Search Documents

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By Lincoln Silva Gomes

Processos metalúrgicos durante soldagem provocam tensões residuais em peças soldadas. Recentemente foi observado um efeito de redistribuição das tensões residuais de soldagem num período de até duas semanas após o termino do processo de soldagem. Existe hipótese nossa que esta redistribuição das tensões está associada a mudança na microestrutura que ocorre no material após do processo de soldagem. Para provar esta hipótese, uma simulação física dos ciclos térmicos do processo de soldagem foi realizada utilizando a simulação física termo-mecânica (GLEEBLE). Através da técnica de microscopia eletrônica de varredura associada a técnica de difração de elétrons retroespalhados (MEV–EBSD) foi observada a variação da misorientação dos grãos e mudanças na microestrutura do material nos primeiros dias após soldagem, acompanhada de redistribuição das tensões residuais.

Aug 17, 2017

If it had not been for the almost unbelievable adventures that came before and after, the last ten months of 19 15 would have been exciting enough for anyone. As it was they were a cheerful interlude. I spent most of the time on our Warren operations catching up on a lot of underground work and visiting Ajo every few weeks to see if my Chuquicamata visit might help solve the New Cornelia problem. While the difficulties were finally solved, at times they seemed almost hopeless. About all I could do to help was to make sure that the ore sent to the pilot plants represented the average ore that must be treated in the final 5000 tpd mill. Dr. Ricketts and John Greenway worked tirelessly with the best consulting advice they could obtain. Credit for the final success was due chiefly to their efforts. Since our old group had given up its "Merry Widow" home in Warren, a few of us got rooms in the company-built Cole Building over the Warren grocery store. This included Jim Lewis, Roy Mitchell, Steve Landon, Paul Stevens, and Hubert d'Autremont who came from Duluth to join our legal staff. Later we rented a small house two blocks from the Calumet and Arizona office. With the now flourishing country club only a 10-min walk away, and an electric car running to it every half hour or so, we were able to give parties in return for the hospitality of our friends. One of the most pleasant episodes came by luck a few days after I got back from Chile. Chester Congdon, a leading director in Calumet and Arizona, with his wife and their daughters, Elizabeth and Helen, spent a couple of days at the Greenway house before making an auto- mobile trip across the desert from Tucson to Ajo. At the same time I arranged to examine the small but rich Bush and Baxter copper mine a few miles from Tucson. At a party in Warren we found we would all be staying at the Santa Rita Hotel in Tucson, and I took my South

Jan 1, 1976

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr203. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 1.6 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, scope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider scopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By Kazimierz Gwizdala

In recent years, in Poland the ATLAS piles have been successfully applied for some constructions near Gdansk. The piles have been used as foundations for housing and another areas of civil engineering, in delta Vistula geotechnical region, characterized by weak, highly compressible soils represented by mud and peat, lying in sub-surface layers, several meters thick. Usually below are dense sandy soils or gravel. In all cases, the base of ATLAS piles rested on sandy soils. The analysis of pile bearing capacity has been discussed and verified by static pile load tests (SPLT). The load-settlements characteristics obtained were satisfactory. In the paper, the results of geotechnical investigations as well as calculations and load tests are shown. The ecological aspects of ATLAS piles application within highly urban areas of the cities and complex geotechnical conditions are emphasized.

Jan 1, 2006

This paper describes the new legislative regime that will apply to the regulation of the minerals industry in New Zealand. The reform of New ZealandÆs minerals legislation was initiated in January 1988 when the Minister for the Environment, Rt Hon Geoffrey Palmer, announced the Governments intention to review all the major laws governing New ZealandÆs resources. The Resource Management Bill is scheduled for introduction to the House in December 1989 and its date of enactment is scheduled for June 1990. With some matters still to be determined (at the time of writing), this paper cannot be a definitive review and description of the new legislation, it is instead an attempt to outline the major features of the Bill, to date, that are seen as important to the mining industry.

Jan 1, 1990

By A. V. Roschin, V. E. Roschin

Composite ores are more often used for production of iron in connection with reserve depletion of traditional ore crude in the regions with developed metallurgy. In particular, the majority of perspective ferrum-ore deposits of the Urals are presented by titanferous magnetite ores which contain a significant amount of titanium and vanadium alongside with ferrum. Thus, the deposits of titanferous magnetites of the Southern Urals on the average contain about 20 % of Fe, 8,7 % TiO2 and 0,24 % V2O5. Due to a high content of titanium oxides it is impossible or it is inexpedient to process such ores in blast furnaces. During work just on titanferous magnetite ore refractory titanium-containing slags are formed in a blast furnace, and in case of its dilution by ores of different types the titanium due to the small content in slag is thrown out. It is often impossible to separate such ores into ferriferous and titanferous concentrates because ferrum and titanium are present in the same minerals. This work attempts to selectively reduce ferrum in solid oxide and to separate metallic iron from titanferousslag with fast fusion. Solid-phase reduction of ferrum has been carried out with carbon at temperature of 1000? 1300°?. In products of solid-phase reduction the extremely disperse mix of metal iron and only partially reduced titanium oxides have been achieved. It is impossible to separate such a mix mechanically. However, the fast fusion of the mix allowed separating it into cast iron and slag with the high content of titanium. Thus the cast iron contained less than 0,1 % of titanium, and the slag did not contain practically any ferrum.

Jan 1, 2007

By Marina Fiore

As otimizações termodinâmicas de sistema ternários ou de maior ordem contendo titânio necessitam que os sistemas binários Ti-X estejam consistentemente definidos e otimizados. O sistema Ti-Si já foi amplamente estudado e otimizado termodinamicamente. Um dos seus compostos intermediários, a fase Ti5Si3, foi inicialmente considerada estequiométrica nas primeiras otimizações termodinâmicas para facilitar os cálculos, embora os resultados experimentais confirmassem a sua não estequiométrica. A otimização mais recente modelou esta fase como sendo não-estequiométrica com 3 sub-redes. A solubilidade foi considerada em duas das três sub-redes, uma na sub-rede do Si e outra na sub-rede do Ti. O problema dessa abordagem é que ela pode aumentar significativamente o número de variáveis a serem otimizadas no cálculo de sistemas ternários Ti-Si-X, dificultando assim a sua convergência durante processamento computacional. O presente trabalho simplifica a otimização do sistema Ti-Si, considerando que o Ti5Si3 é sempre hiper-estequiométrico somente em relação ao Ti. Deste modo, mantêm três sub-redes, mas elimina-se a ocupação do Si na sub-rede do Ti. Os resultados mostram que esta simplificação não afetou significativamente o valor das propriedades termodinâmicas do sistema.

Aug 16, 2017

By J. David Lowell

The first part of this article is a review of industry techniques and styles during the past 50 years. It is followed by my career history during the same period. The second part covers my ideas about what works in mineral exploration. These include estimates about discovery costs, thoughts about education of explorationists, organization of exploration groups and my opinions about the relative value of exploration techniques. Evolution of exploration techniques [Table 1] shows the evolution of mineral exploration techniques and styles from 1950 to 2000. During the first half of that period, there was a progressive increase in exploration drilling. During the second half, there was a decrease in prospecting and an increase in high technology, indirect exploration and a rapid increase in discovery cost.

Jan 1, 2000

By Leandro Brunholi Ramos

As superligas de níquel apresentam boa combinação de resistência à corrosão e à oxidação, resistência mecânica, resistência à fadiga e à fluência, além de conseguirem operar em temperaturas elevadas, mantendo tais propriedades. A liga Inconel 625 vem sendo estudada como revestimentos, obtidos por cladeamento ou aspersão térmica, para tubos de aços ao carbono utilizados nas indústrias de petróleo e gás. Esses tubos poderão ser unidos pela técnica de soldagem, quando então se obtém uma junta Inconel-Inconel, e isso pode acarretar modificações nas propriedades dessas superligas. O presente trabalho objetiva obter uma junta soldada da liga Inconel 625 empregandose o processo de soldagem a arco utilizando eletrodo revestido Ni-Cr-Mo 3 e caracterizar o cordão de solda quanto à microestrutura, à dureza e à corrosão. A microestrutura foi avaliada por microscopia óptica; para dureza foi realizado perfil de microdureza Vickers ao longo da junta soldada; quanto à corrosão foram realizadas curvas potenciodinâmicas em três diferentes soluções: 3,5% NaCl, 3,5% NaCl + 0,01M Na2S2O3 e 3,5% NaCl + 1N H2SO4. Os resultados obtidos mostraram que a zona fundida tem microestrutura dendrítica, sendo a zona afetada pelo calor de aproximadamente 1,2 mm de extensão. A solda não alterou significativamente as propriedades de corrosão e dureza.

Aug 17, 2017

By David E. Albus, Ahmadreza Mortezaie, Bidjan Ghahreman

The structural evaluation of seismic performance of an existing hospital in Long Beach, California, required spring constants of foundation elements. The structure included support by deep foundation elements comprised of belled (underreamed) caissons. The available relationships in the governing building code (ASCE41-13) to compute axial stiffness is not applicable due to the belled configuration of the caissons. The large diameter of the bells required consideration of the foundation medium to the axial stiffness; a detail not clearly described in ASCE 41-13. Furthermore, prescriptive equations in ASCE 41- 13 used to estimate lateral stiffness only consider pile groups with the assumption that the only source of lateral stiffness is the axial reaction of individual piles. These assumptions were invalid for the project at hand where all caissons are configured as single foundation elements, not a pile group. In the present work, the approach taken to estimate seismic stiffness of single-belled caissons is described which accounts for the elastic behavior of the foundation medium below the bell base and lateral behavior of single-pile shafts. Results of the work provide a more satisfactory derivation of the spring constants consistent with current modeling methods. INTRODUCTION Seismic evaluation of an existing hospital in Long Beach, California, required geotechnical investigation followed by site-specific ground motion analysis. This evaluation was required by the Office of Statewide Health Planning and Development (OSHPD) in order to meet the requirements of the Structural Performance Category 4D (SPC-4D) published as a part of the 2016 California Building Code, CBC (Section 3412A). SPC-4D utilizes ASCE41-13, as modified by OSHPD, and involves two seismic performance objectives: BSE-1E (20% probability of exceedance in 50 years) and BSE-2E (5% probability of exceedance in 50 years). Spring constants and capacities of foundation elements were needed for evaluation of the structural performance of the building subjected to these two performance objectives. Our review of the as-built foundation plans indicated that both shallow footings and caissons were used for support of the structure. The plans demonstrated that all caissons are belled (under-reamed) and are individual, i.e. not part of pile groups. In this paper, the subject site condition and foundation elements are described first. This is followed by details of assessing spring constants and vertical capacities for belled caissons. The new requirements of the 2016 CBC concerning the evaluation of critical facilities will likely entail evaluation of other structures with belled caissons due to the more extensive use of these foundations in the past. This paper proposes a method to address the conditions of individual belled caissons not explicitly considered in the current code provisions.

Jan 1, 2018

By Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, Maurício Covcevich Bagatini, Beatriz Fausta Gandra, Adriano Cesar Carvalhido

O combustível com menor granulometria, denominado small, pode ser carregado juntamente com a carga metálica, em substituição ao coque, no intuito de melhorar as condições de permeabilidade do gás e a redutibilidade da carga no alto-forno. Na Usiminas, o equilíbrio na geração e no consumo desse material limita o seu uso em taxas abaixo da média nacional. Nesse sentido, foi avaliado o efeito do coque verde de petróleo (CVP) em substituição ao small coque no consumo de combustível e na estabilidade operacional do alto-forno. Os resultados do teste industrial indicaram a possibilidade de substituição até 45 kg/t gusa, com manutenção do fuel rate, da permeabilidade e da produtividade do alto-forno.

Oct 1, 2019

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By Andrea McGlynn

Iron Ore Company of Canada, Labrador City 2011?Canada's largest iron ore producer, leading global supplier of iron ore pellets and concentrates ?Rio Tinto (58.7%), Mitsubishi Corporation (26.2%), Labrador Iron Ore Royalty Income Fund (15.1%)

May 1, 2011

By Jorge Acosta Ale

El presente texto señala la dotación del cobre en el Perú desde el período 2013, la cual se encuentra ubicada en tres franjas metalogenéticas como son: Paleoceno, Eoceno-Oligoceno y Mioceno. Estas franjas produjeron más de 24 Mt de cobre y aún guardan reservas y recursos que llegan a 192 millones de toneladas. En ese sentido, el futuro de la producción de cobre se encuentra en 18 proyectos mineros, los cuales bajo un escenario optimista ingresan en producción entre 2014 y 2019. Para realizar este trabajo, se ha considerado datos estadísticos de producción global de cobre de la United States Geological Survey, y de la producción nacional de anuarios mineros del Ministerio de Energía y Minas el Perú hasta el año 2013. Los datos de reservas y recursos de operaciones y proyectos se han tomado de reportes anuales de compañías mineras y de exploración en el Perú.

Dec 1, 2014

By Leandro Augusto Justen Marzulo, Guilherme Lucio Abelha Mota, Otávio da Fonseca Martins Gomes, Gilson Alexandre Ostwald Pedro da Costa, Alexandre da Costa Sena, Felipe Schimith Batista

O presente trabalho desenvolveu uma solução, utilizando Hadoop e Map Reduce for C (MR4C), capaz de paralelizar a segmentação de fissuras em imagens de partículas minerais. Um conjunto de 221 imagens de tamanhos distintos de partículas de minério de cobre obtidas por microscopia eletrônica de varredura foi utilizado para os testes. A variação do número de nós de processamento apresentou um ganho do tempo de execução que escalou de forma quase que linear. O balanceamento de carga estática promoveu um speedup de 1,3. A solução proposta, quando comparada à implementação sequencial, considerando um cluster com 9 nós de processamento, atingiu um speedup de 19,1.

Oct 1, 2019

By S. D. D. Welsby

"A pilot-scale flotation column was used to evaluate four polyglycol frothers at Teck’s Highland Valley Copper Mine. The column was fed with flotation plant feed from the grinding circuit cyclone overflow. Frother dosage was changed by controlled addition to the column feed. Pulp, froth and metallurgical performance were assessed using gas dispersion measurements, water recovery and copper, molybdenum and gangue grades and recoveries. Ranking the frothers based on pulp and froth phase performance using gas dispersion measurements and water recovery yielded contradictory rankings. All of the frothers changed the froth structure in a similar manner such that, at the same structural conditions, they all gave the same degree of separation between water and entrained solids. The only difference between the frothers was what dosage was required to achieve a certain structure. Changes in pulp structure appeared to be related to the critical coalescence concentration (CCC) for each frother. Changes in froth structure were not completely described by the CCC and involved other factors, such as the hydrophobicity of particles in the froth. All of the frothers were capable of achieving the same metallurgical result, just at different dosages. Optimal dosages for the frothers were anywhere from the CCC, where copper and molybdenum grades were maximised, to 2 to 3 or 4 to 7 times the CCC, where copper and molybdenum recoveries, respectively, were maximised.INTRODUCTION Background Due to supply issues, Teck’s Highland Valley Copper (HVC) Mine replaced Dowfroth 250C, their auxiliary frother, with Huntsman Polyfroth W31. The primary criterion for selection was that the new frother gave the same performance as Dowfroth 250C, minimising disruption to the circuit. Frothers play a dual role in flotation, altering the bubble size in the pulp zone and the stability of the froth. A stronger or weaker frother, or a blend of both, will alter the balance between pulp and froth effects and, ultimately, metallurgy. Dowfroth 250C and Polyfroth W31 may not necessarily be the best frothers for HVC from a metallurgical standpoint. There may be a different frother or frother blend that could deliver higher recovery in the bulk roughers."

Jan 1, 2014

Essential features of the role of the fill material in mechanized cut and fill mining are discussed, with particular emphasis on its dewatering and strength development after emplacement. The fill material is regarded as a chemically-reactive porous medium, the most important property of which is permeability. Methods are described for measurement of permeability and other fill properties and results of such measurements applied to develop an orderly approach to the operation.

Jan 1, 1966

By K. Duckworth

"Comparative tests of the conventional Turam survey configuration and an alternative configuration called the Tx-parallel configuration were conducted at the McClean uranium deposit in northern Saskatchewan. Both configurations detected the known conductors at the site but the alternative configuration demonstrated its particular effectiveness in the reconnaissance role. This effectiveness results from the fact that the length of Tx-parallel traversesis controlled only by the length ofthe transmitter and not by its power. In addition, the field strength along a Tx-parallel traverse is uniform unless the traverse approaches the end of the transmitter. This freedom from a strong gradient of the primary field along a Tx-parallel traverse eliminates the gradient-induced anomaly shifts which are common in conventional Turam operations. The locations of each of the McClean conductors, that were obtained from the Tx-parallel profiles, werein better agreement with the locations known from drilling than were the locations obtained from the conventional profiles. However, the conventional profiles gave better estimates of the conductance of the targets.The results obtained over the McClean conductors indicate that current gathering has a strong influence on Tx-parallel results with consequent unpredictable influence on depth and conductance estimates. However, the depth estimates obtained from the Tx-parallel data appear to be in good agreement with the known depth of the McClean south conductor. The Txparallel results provide shallow estimates of the depth of the McClean north conductor which suggest that the fracture zone above the graphitic conductor is a significant conductor as was also suggested by earlier VLF surveys.Comparison with the wide range of published geophysical test surveys for the McClean site showed that apart from the work required to lay the transmitter, the Tx-parallel mode of operation of a Turam exploration system is operationally very similar to a moving source Slingram type of survey. At the McClean test site, it provided the same depth of exploration as a conventionally deployed fixed loop transmitter."

Jan 1, 1988

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987