Search Documents

By W. P. Yant, G. W. Jones

"Introduction.During the past two years the Bureau of Mines has conducted a study of natural-gas heaters*** to determine (1) what types of heaters literate carbon monoxide; (2) why carton monocide is liberated; and (3) how, by change of design or construction, the liberation of this gas can be largely eliminated, In addition to the above study the bureau has investigated cases in the Pittsburgh dis¬trict where fatalities have resulted from carbon monoxide given off by natural-gas heaters.Since these fatalities were first brought to the attention of this bureau through the press, it is likely that some cases were missed and thus not listed. On the other hand, some cases reported as being due to carbon monoxide poisoning, on investigation were found to be due to causes other than carbon monoride.The cases listed herein were shown in all probability to be due to carbon monoxide. Those in which there is any doubt have been omitted; so have those in which there was part asphyxiation, where the victims later recovered."

Feb 1, 1924

By Fulvio Tonon

And Rabcewicz said ?tunnels should be driven full face whenever possible.? ADECO, which stands for ?Analysis of Controlled Deformations in tunnels,? now allows us to fulfll Rabcewicz?s dream in any stress-strain condition. In order to achieve that dream and its consequent control over cost and schedule, however, NATM must be abandoned for the ADECO. The paper presents the basic concepts in the ADECO approach to design, construction and monitoring of tunnels together with some case histories, including: full face excavation for Cassia tunnel (width of 22 m, height of 14 m) in sands and silts under 5 m cover below an archeological area in Rome, Italy; Tartaguille tunnel (face area > 100 m2) advanced full face in highly swelling and squeezing ground under 100 m cover where NATM led to catastrophic failure, France; and 80 km of tunnels (face area > 100 m2) advanced full face in highly squeezing/swelling ground under 500 m cover for the high-speed railway line between Bologne and Florence, Italy (turnkey contract).

By AIME AIME

I am happy to welcome you to the twenty-third conference of the National Open-Hearth Committee, and our joint conference with the Blast Furnace Committee, of the American Institute of Mining and Metallurgical Engineers. It is appropriate that, for our fifteenth year anniversary, we should meet in the hotel and the city where this Open-Hearth Committee was inaugurated in 1925. At that first meeting, only a handful of men from a number of steel companies met to discuss ways and means to start a movement to improve the practical and metallurgical technique of open-hearth operations among independent manufacturers, as the United States Steel Corporation had carried on for many years.

Jan 1, 1940

By Carlos Gonzalo Alvarez Rosario

A reciclagem de resíduos eletroeletrônicos (REEs) é importante tanto no aspecto ambiental quanto econômico, uma vez que através do reaproveitamento do REE há diminuição da quantidade de resíduos a ser destinados, além disso, contribui para a sustentabilidade do setor minero metalúrgico, pois é possível a recuperação dos metais provenientes de REEs. Presentes na maioria dos equipamentos eletroeletrônicos, as Placas de Circuito Impresso (PCIs) são compostas por materiais cerâmicos, metálicos e poliméricos. Além disso, a heterogeneidade do material influi diretamente no tipo de processamento/tratamento a ser utilizado, desta forma a caracterização prévia do resíduo é uma etapa fundamental para determinação da rota de processamento a ser utilizada. Assim, no presente estudo é apresentado o processo de caracterização de PCIs proveniente de computadores obsoletos objetivando a determinação e quantificação dos metais presentes, de forma a estudar a influência dos mesmos em processos de biolixiviação futuros. A rota de processamento físico incluiu inicialmente processo manual utilizando guilhotina e, posteriormente, moinho de martelos com grelhas de aberturas de 6 mm e 2 mm. A caracterização foi realizada através de ensaios de perda ao fogo, lixiviação ácida e MEV/EDS e a concentração dos metais foi determinada por ICP-OES. Os resultados mostraram que 50% do material particulado tem granulometria maior que 0,25 mm; as PCIs estudadas possuem 35,6% de metais, 27,2% de polímeros e 37,2% de cerâmicos. Dos metais presentes nas placas o mais representativo foi o cobre com 21,4% em massa enquanto que metais como Fe e Al apresentaram 1,1% e 1,9% em massa.

Aug 8, 2018

By Ulf G. Gwildis

The Bright water Conveyance System includes 21 km of tunnels mined by two earth pressure balance Tunnel Boring Machines (TBMs) and two slurry TBMs. The probabilistic baseline approach defined in the Geotechnical Baseline Report (GBR) can representatively be verified by use of a comprehensive tracking system to identify face conditions that allows comparison with the baselines. The glacial geology includes a high lateral variation in soil types that, when combined with the pressurized face tunneling methods, creates challenges for documenting face conditions. Baseline tracking using spoil samples and TBM operational parameters provides information to document actual conditions and support resolution of differing site condition claims.

By Ronald F. Balazik

This Bureau of Mines study identifies and examines the costs of Federal, State, and local environmental protection controls on domestic phosphate rock mining, The costs include the expenditures needed to comply with government regulations and the effects that these expenditures and regulations have on supply. The study analyzes costs of environmental impact assessments, air and water quality standards, reclamation laws, potential solid waste controls, and local government restrictions. In addition, an industry survey and the Bureau's Minerals Availability System (MAS) are used to evaluate land management policies that restrict access to phosphate resources, Conclusions drawn from these analyses confirm that (1) domestic phosphate mining has incurred substantial control costs and may be subject to significant new regulatory costs in the next several years, (2) certain environmental controls can discourage mining investment, (3) environmental policies governing land-use controls affect the disposition of sizable phosphate resources, and are key determinants in the development of those resources on the Federal do- main, and (4) environmental costs could diminish the competitiveness of domestic producers.

Jan 1, 1983

New Zealand depends on foreign investment for economic development. This also applies to the development of New Zealand's mineral resources. For this foreign investment to happen there must be some incentives to attract the investment. While prospectivity is the dominant parameter considered by investors it is not a variable that can be changed, only the perception of New Zealand's prospectivity. Other parameters likely to be considered are sovereign risk, red tape, green tape, land access, civil unrest, land claims, social risk, labour relations, infrastructure and natural disasters. Regulators and political will can vary some of these parameters. Where New Zealand fits internationally can be measured by investors' perceptions of these parameters. Following on from these perceptions New Zealand can be seen to have advantages in some areas and be disadvantaged in others. How to deal with the disadvantages to give investors confidence is not easy in the New Zealand environment where the development of mineral resources plays a small part in an economy dominated by agriculture. Added to this is the current global state of the minerals industry which offers even more of a challenge to attract foreign investment to develop New Zealand's mineral resources.

Jan 1, 2000

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By Donald Leroux, Jean-François Wilhelmy, Ahmed Bouajila

"A young private R & D organization, COREM celebrated its 10th anniversary in 2009. Managed by a consortium of nine mining and metallurgical companies, COREM has the mandate of increasing the competitiveness of its member companies through the development and transfer of mineral processing innovations. Typical technologies developed by COREM include alternative mineral processing techniques, novel operating strategies, innovative sensors and process simulation software. Many of them were developed in partnership with universities and selected research organizations.Because the COREM membership base is broad (from ferrous to base, to precious metal industries), its R & D program must deliver technologies with applications within a wide spectrum of mineral processes. Comminution, physical (gravity and magnetic) separation, flotation, cyanidation, pelletizing and thermal processes are the main topics of the R & D program. A number of new technologies have been developed and transferred to the plants of member companies. These examples of transferable technologies demonstrate the capability of COREM to impact the bottom-line of its member companies.INTRODUCTIONCOREM is a private mineral-processing R & D organization that operates from its own laboratories and pilot-plant with its own staff of professionals and technicians (about 95 persons). It is managed and financially supported by a consortium of nine mining and metallurgical companies and three provincial and federal ministries. The very ‘down-to-earth’ mission statement of COREM is to increase the competitiveness of the mineral processing plants of its members. The eighteen plants upon which the COREM technology development program is currently based can be found in Québec, Newfoundland and Labrador, New Brunswick, the Netherlands and Botswana."

Jan 1, 2010

By R. A. Meister

The study on improving surface coat refuse disposal site inspections included surface inspections of 15 refuse disposal sites. Monthly aerial photos were taken of the sites and computer methods were used to determine elevation changes. Photogrammetric techniques that were used are described in detail. A comparison of the results of each of these inspection techniques is included. A detailed evaluation of the photogrammetric techniques was made and conclusions were drawn concerning the advantages and disadvantages of using aerial photography and photogrammetry as part of the inspection procedure. Operators' opinions of the aerial photography methods are included.

Jan 1, 1980

The object of this talk is to bring before members the importance of the prospector and the' State Battery system to the wealth and prosperity of the mining industry in particular and the State of Western Australia in general, and to touch on the more important features.Customs plants of any sort are usually subject to a good deal of critioism, usually on the large profits made at the expense of the customer, etc., and this often clouds the real value of the work being done.Prospectors, on the whole, are a good class of men; they work under conditions and difficulties which would deter those less spirited. Food, water and mining supplies are often difficult to obtain and frequently have to be transported great distances. Their mining tools are usually of the most primitive type, yet during last year over 109,000 tons of prospectors' ore were handled by the State Battery system for 73,250 fine oz. valued in Australian currency at over £587,000, the value being 57/- per long ton at par.This production brings the State Battery system into fourth position amongst the producers of the State, the yield being exceeded by the Lake View and Star, Wiluna and the Great Boulder.In passing I might mention that these notes were written at the end of the year 1940, and the above figures were for the previous period. The figures for last year, 1940, were not quite so good, being 101,000 tons for approximately 60,000 fine oz., valued in Australian currency at £572,000.In spite of this drop the State Battery system maintained its position as fourth in order of gold output for the State.The extractions, as a whole, throughout the system, were 92·54%, made up of 68·86% by amalgamation and 23·68% by cyanidation. These figures, for a group of 20 plants treating widely different classes of ore, must be considered satisfactory. The total production since inception is over £11,000,000 in Australian currency.State Batteries are usually more or less of a standard design. Ore is reduced to about 2i in. maximum size before being sent to the bins. Challenge automatic feeeders control the feed to each mill unit, amalgamated copper plates collect the free gold. Corduroy strakes are used with some ores after amalgamation, but in only a few cases has this been found of any advantage to the customer.The pulp from the battery is sampled, after leaving the tables, with a "Tazewell" sampler and pumped to dams for subsequent cyanide treatment.The "Tazewell" sampler is a machine driven by the moving pulp; and takes about fifteen dips per .minute from such pulp through a slotted...

Jan 1, 1941

By A. J. Potgieter, C. Hill, A. Humpel, D. S. Magudulela, V. Scholtz, A. Coetzee

Keywords: Pyrometallurgy, long steel products, coke, sinter, blast furnace, steel plant Located in Northern KwaZulu Natal, Mittal Steel South Africa Newcastle works produces roughly 1.8 million tons per annum, supplying long steel products, locally and overseas. The great extent of local raw material availability and low conversion cost ensures that Mittal Steel South Africa is among the lowest cost, high quality producers of steel. MSSA Newcastle works can be subdivided into two main sections: The iron making side, comprising the coke ovens, sinter plant and blast furnace, and the steel making side, comprising the basic oxygen furnace, ladle furnace, continuous casters, and the medium, rod, and bar mills.

Jan 1, 2006

By Glenn S. Dobby, Glenn A. Kosick

"Column flotation circuit engineering has matured to a good level of understanding regarding testing, scale-up and design. Some of the factors important to the process of implementing columns are addressed in this paper, highlighting the following issues• operating bias and the maximum achievable solids carrying rate for a column application.• internal circulating loads of full scale and pilot plant flotation columns• short-circuiting oflarge scale columns and the impact on separation selectivity• the number of stages in a column circuit and the impact on selectivity.The paper uses several case studies, from pilot plant to full scale implementation, to illustrate these design issues.1. IntroductionTen years ago, in 1984, there were very few column flotation installations world wide and the largest columns were about I . 5 to 2 m diameter or square. During the following decade there have been in the heighbourhood of 80 column installations that have been successful and profitable, as both retrofits and green-fields plants. Now, columns as large as 3 to 4 m are not uncommon. Examples of installations with many large columns include Escondida, with ten columns each at 4 m square, and P T Freeport Indonesia, with 21 columns: nine 3 m diameter columns, four 2.4 m diameter columns and, starting up in April I 995, eight 3.6 m diameter columns.During this growth period there have also been column installations that can be considered as failures. In the majority of these cases, the reason for their failure has been an insufficient installed capacity for applications where there is a high weight recovery of solids to the froth product These include zinc cleaning, copper cleaning and iron ore flotation (silica flotation from a feed that is 15 to 30 %Si02) An application with high weight recovery to the froth product makes column scale-up and circuit design more complicated. This is particularly so if a high degree of selectivity is also required while attaining a high weight recovery, which can happen with iron ore flotation in columns."

Jan 1, 1995

LARGE-SCALE production of zirconium by the Northwest Electrodevelopment Laboratory of the Bureau of Mines at Albany, Oreg., is an anomaly that justifies some explanation. The reduction of titanium tetrachloride with magnesium in an inert atmosphere, as perfected by Dr. W. J. Kroll before 1940, aroused renewed interest in zirconium, and in 1945 development work on this metal was initiated at Albany under Dr. Kroll's technical direction. Preliminary results were promising, and in February 1947 a pilot plant with a weekly capacity of 60 pounds of zirconium-metal sponge was put in operation. Shortly thereafter the Oak Ridge National Laboratory of the Atomic Energy Commission requested production of 1 ton of zirconium-metal sheet, with the provision that it have a low hafnium content. The Bureau of Mines was furnished with a. supply of Brazilian baddeleyite ore, containing less than 1 percent hafnium with respect to zirconium, from which was made about. 2,700 pounds of relatively low hafnium zirconium sheet of 0.080-inch thickness for test purposes. This was accomplished by melting zirconium sponge in a graphite crucible, hot-rolling the ingot in an iron sheath, and finishing by cold rolling. Concomitantly the Oak Ridge Laboratory developed a method for separating hafnium from zirconium; and, in cooperation with the Atomic Energy Commission and the Bureau of Ships of the Department of the Navy, a, larger pilot plant was erected to produce zirconium from very low hafnium zirconium tetrachloride furnished by the Commission. Pilot-plant work on producing zirconium tetrachloride from zircon sand and baddeleyite was discontinued. Production of zirconium sponge in the larger pilot plant of 500 pounds per week capacity was begun in June 1949.

Jan 1, 1956

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By Kenny Lo

"SummaryFor more than a century, ground freezing has been a construction technique used in stabilization of ground by means of lowering the temperature of surrounding soil strata. This technique is used in circumstances where conventional grouting method is unable to achieve the degree of consolidation required to prevent settlement and water ingress during the execution of underground excavation. Whilst ground freezing is effective in imparting self-supporting characteristics to the excavation profile, it poses significant challenges when it comes to the New Austrian Tunneling Method (NATM) where sprayed concrete is used to support the freshly excavated ground. Sprayed concrete, if used in an appropriate manner, provides a fast, efficient and structurally-reliable means of supporting the structure, especially in underground construction. The evolvement in sprayed concrete technology is attributed to the development of concrete know-how, improvement of spraying technique with the use of automation spraying equipment, more in-depth understanding of sprayed concrete behavior and enhancement of materials used in production of high quality sprayed concrete Not only has this markedly escalated the prominence of sprayed concrete on wider perspective,. the positive development has also pushed sprayed concrete beyond its boundaries, enabling it to be embarked on area of application not considered possible decades ago. Nevertheless, sprayed concrete, for all its placement versatility, still depends largely on the technicality provision very similar to concrete to achieve the required quality. Parameters such as raw material grading composition, curing temperature and cement quality are some of the factors that can easily sway the quality of concrete from one extreme to another. Conducive ambient temperature is critical in ensuring optimum hydration of concrete. This is more important in sprayed concrete where temperature plays a pivotal role in influencing the early strength and long term strength development. The low temperature imposed by ground freezing is everything but ideal for competent hydration to take place. This paper outlines how the innovative use of sprayed concrete helps to overcome the adverse ambient temperature in the construction of a 110m underground pedestrian walkway utilizing ground freezing technique in Hong Kong."

Jan 1, 2016

By Herbert Tomlinson

The United States Bureau of Mines has engaged in a study of the conditions under which coal mine accidents, resulting in the loss of life, limb, or time to the injured person, occur from falls of roof and coal. This publication is devoted to the results of a study conducted in the coal mines of the Book Cliffs and Wasatch Plateau coal fields of Utah. To show the necessity of this study, a statement of the fatalities that have occurred during the period 1928-1930, inclusive, in the bituminous mines of the United States and of Utah, is presented (Table 1), followed by a brief description of this Utah district, its coal beds and immediate roof, thickness of cover, dip of coal beds, methods of mining, supervision, roof testing and timbering for roof support, all of which are factors in any plan devised for preventing accidents from falls of roof and coal.

Jan 1, 1932

By Diogo Barcellos Moraes

O trabalho surgiu mediante a necessidade de reduzir o tempo de paradas do equipamento de laminação a frio por ruptura de fio maquina durante as reduções nos passes de laminação. Para que não ocorra ruptura do fio máquina durante as reduções nos passes, faz-se necessário uma boa lubrificação do fio maquina antes de iniciar o contato do mesmo com os anéis de laminação e para que isso ocorra de forma eficaz o fio maquina deve estar completamente seco antes de passar pela caixa de lubrificação. Sendo assim, desenvolvemos um secador de fio para que garante a secagem antes da lubrificação, de modo a evitar empedramento do sabão, má lubrificação e consequentemente rupturas.

Aug 16, 2017

By Samara Venina Simen de Azeredo Silva

Os compósitos produzidos a partir de Nitreto cúbico de Boro (cBN) são utilizados nos processos de usinagem de materiais ferrosos, tais como, peças fabricadas a partir de ligas ferrosas, ligas a base de níquel e materiais ferrosos com dureza de 45 HRc. Os compósitos a base de cBN são produzidos sinterizando cBN e seus ligantes sob condições de altas pressões e altas temperaturas (APAT). O presente trabalho tem como objetivo a caracterização microestrutural dos compósitos nanoestruturados de cBN, processados sob altas pressões e altas temperaturas, com parâmetros de pressão de 6,6 GPa e 1800oC e tempo de processamento cíclico e acíclico. Os compósitos produzidos foram testados na usinagem de aço 4140. Os resultados mostraram que uma melhor densificação e uma menor perda de massa dos compósitos durante a usinagem tem relação com os parâmetros de sinterização e com o tempo de processamento.

Aug 16, 2017

By William G. Hedling

The operation of electric face equipment in underground coal mines has proven to be extremely hazardous to mining personnel, including equipment operators and others working in the vicinity of active equipment. Recent industrial engineering studies* of accidents and fatalities indicate that a major contributor to this hazardous situation is noncompliance with modern principles of human engineering, particularly lack of standardization of control configurations. Control configurations differ not only among different machine types, but also among the same machine types produced by different manufacturers. This lack of standardization can produce a high incidence of error in the operation of electric face equipment, thus creating a potential source of accidents. Other examples of non-compliance with human engineering principles are the widespread use of identical black, round control knobs (regardless of the function being performed), and the inappropriate location, spacing, and labeling of controls. Any or all of these factors may place the operator in a "negative transfer" situation, which means that control manipulations appropriate for one type of machine are different from (or even the reverse of) the control movements required to produce the same effect on other machine types. This situation increases the accident potential to the operator, as well as to others in the vicinity. Accident potential is further increased by circumstances which do not allow for large error tolerance-specifically, emergency procedures. Reports of accident statistics cite operator inexperience as a primary cause of most accidents involving underground electric face equipment. Several factors contribute to operator inexperience, including: 1. High personnel turnover 2. Employee absenteeism 3. Current union practice of bidding for jobs.

Jan 1, 1974