Search Documents

By Andreza Menezes Lima

Dispersões de óxido de grafeno foram caracterizadas com respeito ao tamanho de cristalito e número de camadas, a partir do emprego das técnicas de difração de raios X, espectroscopia Raman e microscopia de força atômica. Todas as análises forneceram valores menores que dez camadas de carbono e concordantes com o reportado por outros autores. Os métodos de difração de raios X e microscopia de força atômica permitiram obter valores mais próximos, em comparação ao obtido por espectroscopia Raman.

Oct 30, 2017

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By L. J. E. Hofer

THIS BULLETIN analyzes and summarizes research at the Bureau of Mines dealing with the preparation, properties, and reactions of iron carbides in the period 1948-60, part of which was sponsored by Wright Air Development Laboratories. The objective was to develop better catalysts for the synthesis of methane and higher hydrocarbons from hydrogen and carbon monoxide. The investigations resulted in the first adequate characterization of epsilon iron carbide, which later proved to be an important intermediate in the tempering of martensite in steel. At temperatures near 170° C, the carbon in carbon monoxide reacts nearly quantitatively with finely divided alpha iron to form an iron carbide in which the metal atoms occupy the positions of the close packed hexagonal arrangement with lattice parameters of ao=2.754 A and co=4.349 A. The carbide has a composition within 2 atomic percent of that required for the formula Fe2C, a Curie point of about 370° C, a specific magnetization of 160.4 ergs per gauss-gram Fe at 50° C, and a ferromagnetic moment of 1.70 Bohr magnetons. Epsilon iron carbide can be converted to chi iron carbide by thermal treatment at 343° C for about 70 hours. The chi iron carbide so formed has a Curie point of 247° C, a specific magnetization of 142.5 ergs per gauss-gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 5.5 Bohr rnagnetons per iron atom. Direct synthesis of this carbide from carbon monoxide at 240° C indicates a composition within 7 atomic percent of that required for Fe2C. Chi iron carbide can be converted to cementite at 550° C in about 315 minutes. The theta iron carbide so prepared has a Curie point of 210° C, a specific magnetization of 147.3 ergs per gauss gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 3.9 Bohr magnetons per iron atom. Pure chi iron carbide reacts to form theta iron carbide by the elimination of free carbon. In the presence of an excess of free iron in intimate contact with the carbide, chi iron carbide reacts with the free iron to form theta iron carbide. The second reaction proceeds at an appreciable rate at 320° C and can be used to snythesize finely divided theta iron carbide with no free-carbon impurity at low temperatures. The ease of the reaction in the presence of free iron suggests that chi iron carbide is an intermediate in the tempering of epsilon iron carbide to theta iron carbide as it proceeds in steels. Experiments on carbon steel show that the magnetic moment of the iron atoms in martensite is about 2.2 Bohr magnetons per atom, a value approximately the same as that of the iron atoms in alpha iron. The Curie points of epsilon iron carbide, chi iron carbide, and theta iron carbide were found -in various specimens of tempered steel to be 10° to 20° C lower than normal values. This shift is probably the result of manganese in solid solution. Preparations of various compositions of epsilon iron carbonitrides show many effects of extensive isomorphism between epsilon iron carbide and epsilon iron nitride. The action of carbon monoxide on finely divided alpha iron at 400° C results in free carbon deposits containing filaments about 0.1 micron in diameter and several times as long. The filaments are characterized by nuclei of dense material located midway from each end of the filament. Although carbiding to near completion at 240° C over periods of about 300 hours produces a preparation containing no appreciable percentage of epsilon iron carbide, very brief periods of carbiding of the order of a minute result in the formation of detectable epsilon iron carbide even at temperatures as high as 325° C. The data indicate that epsilon iron carbide is an intermediate in the formation of chi iron carbide during its formation from carbon monoxide in the gas phase. Attempts to convert cementite to chi iron carbide by cold work increased the Curie point but did not change the X-ray powder diffraction pattern.

Jan 1, 1966

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

Rehabilitation, reclamation and restoration are all terms used to describe the repair of land after mining. Here, restoration is used to mean restoring the land's original use, capability or productivity. Effective restoration is dependent on good planning before mining commences and must include a clear definition of post-mining objectives. The physical condition of the land within the mining licence was that of an imperfectly drained soil in permanent pasture, supporting a seasonal supply dairying unit. During the mining process, the soil layers were separated, with the topsoil stockpiled separately. As part of the restoration process, the land was recontoured to encourage surface drainage, with topsoil spread evenly over the recontoured tailings. Low grond pressure machinery was used to minimise soil compaction, with light discing and harrowing used to increase water infiltration. A permanent pasture was sown, with weed species controlled by spraying, both before and after pasture establishment.  Soil testing has been used extensively to ensure there were no nutrient deficiencies that good compromise pasture establishment and performance. Controlled grazing practices were used to ensure that the sown pastures became well established.

Jan 1, 1998

By Marlon Mendieta, Cristhian Guillén, Ned Vásquez

Actualmente en mina Cerro lindo, el 60% de la producción de mineral proviene de la explotación de banqueos descendentes con el método Sublevel Stoping y ante la problemática del incremento de incidencia de “repies” en los tajeos de producción que estuvo afectando la recuperación de mineral y el performance de las voladuras, se tiene como objetivo incrementar la recuperación de mineral y mejorar el performance de las voladuras; se plantearon alternativas y propuesta de mejora en del diseño y esquema de carguio mediante la aplicación de reforzadores de carga, para la explotación de banqueos descendentes.

Sep 29, 2023

By G. C. Mackenzie

At the last Annual Meeting of the Institute, Dr. C. V. Corless sketched the potential mineral wealth of Canada so clearly, graphically and with-all so entertainingly that one's imagination was fired with the promise held out to future generations for the tremendous expansion of the mining industry in the Dominion. Posterity will undoubtedly witness the fruit of much of the geographical search and survey that is now carried on by our government mining departments. Year after year the work advances, slowly but surely, new areas are . explored, older areas are surveyed in detail, the information being compiled in maps and reports of incalculable value to the prospector, the engineer and the general public. The immensity of the task of exploring, geologically, the outlying portions of the country, with the ultimate view of making valuable mineral discoveries, may be visualized from a study of Dr. Corless' paper and the subsequent discussion which took place and one becomes impressed with the fact that three-quarters or more of the problem can be included under the word "transportation". For instance Dr. Corless said, "The few geological explorers who have penetrated to these remoter regions . . . . . . have as a rule been compelled to stick closely to canoe routes,"; Dr. Goodwin remarked, "This barren Laurentian granite, which is put down on the maps as covering the greater part of this area, is the best guess the geologist could make from travelling along watercourses Within the next few years . . . . . . the Timiskaming and Northern Ontario railway will undoubtedly be extended to James Bay . . . . . . In order that we may be prepared for the probable influx of prospectors when transportation facilities to tidewater are provided, I think all available information on this district should be gathered together in handy form." All three-Corless, Goodwin and Cole-emphasize the well-known fact that explorers, geologists and prospectors working in new country must stick to the watercourses and that transportation by rail, road or water has always been the all-important deciding factor in facilitating the exploration and development of remote districts. Dr. Corless did, however, suggest other means of transportation in stating, "The aeroplane will be of assistance in future study of some parts of these remote areas."

Jan 1, 1924

By M. A. Oskouei

Draglines are the main energy consumers in strip mines. Given the growing cost of energy and environmental concerns, it is important to properly understand dragline energy efficiency. The goal of current research at Missouri University of Science & Technology is to account for operator practice and operating conditions in modeling dragline energy efficiency. This paper presents preliminary correlation analysis and a framework for stochastic modeling of dragline energy efficiency. Thirteen operating parameters (including cycle times, payload, swing angle, and height of dump pile), operator working schedules, operating conditions, and drag, hoist, and swing energies were monitored for an 85 yd3 dragline. Operator effects were examined by two-sample t-tests. The relation between the parameters and energy consumption were assessed by correlation analysis and a stochastic modeling framework has been proposed for dragline energy efficiency. The results show that operator effects are significant (p< 0.05) and energy efficiency is correlated with operating parameters. The completed model will help the coal mines better predict energy consumption, with uncertainty, for different operating conditions.

Feb 27, 2013

By Miklos D. G. Salamon

If all stratifications are horizontal, the computation of surface deformation induced by coal mining involves the prediction of roof and floor convergence and then the transfer of the effects of this relative displacement to the surface through the use of the appropriate influence functions. A laminated model, in the form of a quasi- continuum, provides a simple means of computing the approximate convergence distribution and leads to the Gaussian distribution as the influence function. The ideas presented in this paper represent a subtle but fundamental generalization of the influence function Method. It is postulated that the influence of a small area of extraction is proportional to the roof and floor convergence and not to the thickness extracted. This difference in definition removes many conceptual difficulties associated with the influence function method. To demonstrate the utility of the model, the surface disturbances induced by the extraction of a parallel sided long panel are derived. Formulae giving subsidence, tilt, horizontal displacement and strain are given.

Jan 1, 1989

By J Wei, A Yo, R Levy

Waste water reuse from municipal and industrial effluents is becoming increasingly important in many areas around the world. Water scarcity, local regulation and environmental impact are driving many industries like coal and copper mines to reuse the large volume of waste water they produce. For example, the Chinese coal industry generated about 4.2 billion tons of mine waste water in 2005 of which only approximately 30 per cent was reused. Coal energy represents 76.6 per cent of the total energy generated in China in 2007 and most of the coal-fired power plants are located in north-west of China, which is a water stressed area.The selection of mine waste water treatment process is challenging as the effluents typically contains high levels of organic compounds and salinity and their composition can vary significantly. In recent years there has been a growing interest in the integration of ultrafiltration (UF) and reverse osmosis (RO) membrane technologies for mine waste water treatment and reuse.In this paper, an overview of the design and performance of ultrafiltration and RO membranes applied for reuse of mine waste water are discussed. A study was carried out in two effluents treatment plants treating copper and coal mine waste water, which are located in Chile and China respectively. The following topics will be discussed to demonstrate the performance of an integrated membrane system in mine waste water reuse: The main challenges from copper mine waste water treatment: high level of chemical oxygen demand (COD); high level of total suspended solids (TSS); high salinity; high concentration of silica, sulfate, iron and other contaminants; and fluctuation of raw water quality. The main challenges from coal mine waste water treatment: high level of total dissolved solids, and waste water quality fluctuation. Design parameters for waste water treatment systems: Selection of pretreatment for dual-membrane system in the copper mine: Clarifier with coagulation and flocculation to remove high TSS; Dissolved Air Flotation (DAF) to remove non-settling solids; Media filtration to handle fine solids and particulate organics; Activated Carbon filters (ACF) to remove dissolved organics, colour and odours. Selection of UF and RO membranes and specific design of their recovery, flux, chemical dosage and cleaning regimes. Finally, the performance of UF and RO, including the main fouling factors and efficient cleaning procedures, will be presented and compared to the design parameters to demonstrate the efficiency and performance of the selected integrated membrane systems in each case.

Jan 1, 2009

By W Taylor, S Chen, R Haywood, M White, R West, J Ranasinghe

In March 2012 a combined BHP Billiton and Hatch team embarked on a program to improve the concentrate burner efficiency of BHP Billiton’s Olympic Dam copper flash smelting furnace. A multi-faceted approach including an analysis of the furnace using operational knowledge and first principles engineering led to the design and supply of a new central-lance (disperser). A new, patented, swirl method of introducing the copper concentrate into the furnace was developed to integrate with the existing concentrate burner. Plant trials in 2014 demonstrated an increase of nearly 10 percent in the oxygen efficiency of the furnace. The improved efficiency is expected to provide savings in operating costs and asset life extension of downstream gas and dust handling equipment.CITATION:White, M, Haywood, R, Taylor, W, Chen, S, Ranasinghe, J and West, R, 2015. Improved copper flash smelting at Olympic Dam, in Proceedings MetPlant 2015, pp 382–395 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Karla Ticona, Anthony Saldaña, Lourdes Cacya

La aparición del virus SARS-CoV2-2 en la ciudad de Wuhan China y su propagación vertiginosa en el mundo (OMS, 2020), frenó e impactó severamente los sistemas económicos, entre ellos la actividad minera a escala global. Nuestras operaciones en Mina Toquepala de Southern Perú, Grupo México, no fueron la excepción, siendo nuestros compañeros de trabajo y sus familias nuestra mayor preocupación. Es así, que la Alta Dirección de SPCC lideró las acciones necesarias para mitigar el impacto en la salud de nuestros compañeros y sus familias como prioridad corporativa.

Sep 29, 2023

By Thomas Hans Kleine

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

William Kent, New York, N. Y.:—The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is an admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly gives the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton&apos;s address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer—Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, Sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer—Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric transmission, electric smelting. Work of the Chemist and Metallurgist—Explosives, chlorina-tion, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist—Economic geology. Work of the Mining Engineer—Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing those things he was trained to do as a specialist, but in making use of the knowledge of geologists, chemists, and electrical and

Jan 1, 1910

By Rajagopala Reddy Kallu

After the Sago and Darby No. 1 mine incidents, the new regulatory standards for the design of mine seals in underground coal mines of the United States require the mine seals to withstand higher explosion standards. This necessitated for the development of new design approaches and standards. For development of any new design standards or approaches a detailed understanding of effect of key influencing parameters on the stability of mine seal is a must. This paper attempts to address one of the factors, i.e. roof convergence, that play an important role in the stability of mine seal under explosion loading. Initially a couple of three dimensional numerical models were built and tested for different levels of roof convergence. These models confirmed that roof convergence has great influence on seal stability. A detailed study is undertaken, with some simple assumptions, to establish typical influence of roof convergence on the stability of mine seal under different levels of static explosion pressures. Three dimensional distinct element code 3DEC is used for this purpose.

Jan 1, 2007

By Armando Gallegos Monteagudo

El presente texto señala las experiencias realizadas en GERENS, empresa de consultoría y capacitación en gestión del sector minero, formulación, implementación y control de planes estratégicos que utiliza herramientas con un alto nivel ambiental en la creación de valor económica, ambiental para las empresas mineras el Balanced Scorecard (BSC) y el análisis de la cadena de valor de la empresa. El Balanced Scorecard es una herramienta gerencial que apoya la implementación del plan estratégico y permite su monitoreo y control. Para ello, el BSC requiere que el plan estratégico de la empresa se traduzca en objetivos claros y medibles, indicadores, líneas de base, metas, y programas de acción estratégicos y tácticos.

Sep 12, 2005

By Axel Preusse

For the last 150 years, subsidence damage to the surface has been an unavoidable phenomenon associated with underground coal mining. In particular, the mechanization of mining methods in multiple seam mining and the concentration of mining activities in densely populated European metropolitan areas (e.g., Ruhr, Upper Silesian industrial region) have led to mining having a very strong influence on the earth?s surface. In both these regions, surface subsidence of more than 20m has been reported up to now in comparison to the original state. Underground coal mining in these regions strongly impairs all kinds of surface use, such as urban and industrial development, infrastructure (roads, waterways, and railways) and pipelines?without restricting the functionality of those objects to a greater extent. Demanding and, in some cases, globally unique engineering solutions have been developed and implemented for this purpose. The previously mentioned mining and industrial regions are still very strongly characterized by the (increasingly declining) coal industry and will remain dependent to a large extent and for an indefinite period on artificial drainage measures because subsidence that has already occurred is irreversible. This paper will primarily discuss the prediction of subsidence that is caused by intensive multiple seam mining and its influence on surface objects (e.g., underground pipelines). However, an approach for predicting ground uplifts due to rising mine water as a consequence of mine closures will also be described.

Jan 1, 2012

By J A. Rabe, PAP Fouche, K O?Neill

Two of the most important issues mines have to deal with are tracking the ore mined from pit to plant and to test the efficiency of beneficiation equipment. Kumba Resources and Saco Systems are working together at moment to develop a RFID tracer system to help address these issues. This paper will focus on the tracking of ore from pit to plant. The main advantages for ore tracking is to ensure plant feed blending and dilution according to plan. The RFID tracer system works on the basis of a tracer that physically simulates the ore properties and radio frequency technology that facilitates communication with the tracer and allowing information to be stored on the tracer. This paper tends to indicate the progress on the application of RFID tracer technology in the minerals processing environment as tested at Kumba Resources so far. It is concluded that the system has great potential, but some important problems remain

Jan 1, 2005

By Lucas Gonçalves Generoso, Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, Gustavo Serrano dos Santos, Gustavo Alexandre da Costa Manso

O Alto-Forno 3 da Usiminas iniciou sua atual campanha em 1999. Projetada para durar 15 anos de operação, previa-se uma produção de 41 Mt de gusa. A partir de 2008, iniciaram as avarias mais significativas no sistema de refrigeração, possibilitando a entrada de água e os consequentes distúrbios operacionais. Buscando estender a atual campanha até 2021, a Usiminas realizou, dentre outras atividades de preservação, duas trocas de staves, em 2015 e 2018. Neste trabalho, são apresentados o planejamento e os principais procedimentos relacionados à parada operacional do alto-forno para a segunda troca de staves, com foco nas atividades operacionais que permitiram a redução do nível da carga até 25,1 metros em relação ao stock line. Destacam-se os cuidados e o êxito no abaixamento de carga até o nível das ventaneiras e a metodologia de troca de staves adotada. Por fim, a previsão de extensão da campanha em 7 anos, possibilitará atingir uma produção acumulada de 53,5 Mt, superando em 12,5 Mt o valor projetado.

Oct 1, 2019

By N. W. Johnson

"Two analysis tools which have been applied to problems in industrial flotation processes are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. This paper describes practical examples of the application of kineticsto examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.IntroductionMuch of the published industrial flotation data on the behaviour of minerals in various size fractions have been obtained from specially conducted surveys with a duration of several hours. Such data are very valuable and provide a record of the behaviour of the entire flotation plant or sections during the interval of the survey. Some examples from the literature can be cited Cameron et al. (1971), Lynch et al. (1981), Frew (1982). Less attention has been given to the value of complementary sized data derived from compositing shift or daily inventory samples over an interval of one or several weeks with repetition of the procedure at the completion of each interval. Mineralogical point count data of the size fractions of such samples and data interpretation are rare in the literature.Kinetic data on the behaviour of valuable and gangue minerals in various size fractions have been reported often for flotation banks. In the experience 0 f the writer, there has been a tendency among operating metallurgists to ascribe problems in the flotation process to rate constant values for gangue minerals which were believed to be unsatisfactorily high. Less attention has been paid to the value for the rate constant for the valuable mineral over the length of a particular bank.Examples of the types of data which were mentioned previously have been obtained from the lead-zinc concentrator at Mount Isa Mines Limited. The various types of data have been collected to evaluate their worth in order to provide relevant information for both research and operational aspects of the plant."

Jan 1, 1987