Search Documents

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

By J. D. Dixon

This Bureau of Mines report describes a technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. The technique is adapted for use with a nonlinear finite-element computer code, NONSAP, to obtain stabilization pressures for linear or nonlinear stress distributions in the rock media around the excavation. This analysis permits a point-wise calculation of active rock pressures that depend on the values of shear stress and strength along the excavation surface. The approach is applied to the solution of several sample problems. The results show that both the magnitude and the distribution of stabilizing confining pressures are significantly influenced by rock and joint strengths, joint orientation, and biaxial nature of the load field.

Jan 1, 1976

The mining industry to the lay mind is one which appears peculiarly dangerous, partly because the accidents which take place are usually of a very tragic nature, and partly because other, industries claim victims more from disease than fromviolence, and their fatal nature is not advertised to the same degree so that in spite of this idea of unusual risk, it is a fact that mining will compare favourably, as regards vital statistics, with nearly all other trades requiring special training.Neverthelessthere are a larger number offatal and serious accidents occurring year by year than one would like to see, and could the deaths which take place by accident be eliminated, it is safe to say that mining would become one of the most healthy of all species of skilled labour. If we examine the accidents appearing yearly in the reports of the Mining Departments of the various colonies, it will be at once admitted that many of them need riot, and in many cases ought not to, have occurred.It is, therefore, the object of tbis essay, to pass under review the ordinary precautions which should be adopted to minimise, as far as possible, the dangerous factors whereby fatalities are brought about.

The Bayswater seam of the Singleton Coal Measures is discussed in relation to its field occurrence and related li~hotype profiles. The seam is correlated throughout widely separated areas of the Hunter Valley with the Farrells Creek seam at Howick, Broke seam at Broke, and Saddlers Creek seam at Mt. Arthur. The unusual features of composition of the seam in relation to adjacent seams is dealt with in terms of the seam environment, particular attention being given to the sandstone at the base of .the seam. Petrographic and other data are used to support the arguments submitted.

Jan 1, 1973

By D. H. Trollope

In engineering in general, close agreement between theoretical predictions and structural performance is rare—this is particularly true in rock slopes. Since the complexity of natural arrangements makes exact theoretical solutions of associated structural problems almost impossible, the role of theory should be that of developing guides or markers to which observations and experience can be related. The author in this paper has outlined the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Some important practical considerations result—especially in regard to horizontal stresses—when theory is compared with full-scale experience. In the field of engineering activity, specific examples of close agreement between theoretical prediction and structural performance are rare. Particularly is this so for the case of rock slopes, where, owing to the complexity of the natural arrangements, it is quixotic to expect exact theoretical solutions to the associated structural problems. The role of theory is rather that of developing signposts or guide rails to which observations and experience can be related. It is with this in mind that the present paper has been prepared; the author's aim has been to set out briefly the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Despite the idealization of the problem, it will be seen that the theoretical conclusions are in accord with full-scale experience, particularly as far as horizontal stresses are concerned, and they point to some important practical considerations. CLASSIFICATION OF ROCK SLOPES At the risk of over-simplification, an attempt has been made to classify the problem of rock slopes into three broad categories with respect to internal stress systems. These are illustrated in Fig. 1. It is tacitly assumed in this classification that the strength of individual particles is very much greater than the interparticle strength whether the particles are the crystals of an igneous rock (Case I) or the blocks of Cases 2 and 3. The Homogeneous Monolith: This case is representative of uniform unjointed rock. Under relatively low stress conditions the internal stress system may approximate to that of an elastic body as given by Terzaghi.' It is more usual, however, for overall stability, to consider the material as a rigid plastic which yields in shear when S =C + c tan 4> where S is the shear yield stress, o is the normal stress on the surface of failure, and C and d are empirical constants according to the Mohr-Coulomb criterion of failure. Sokolovsky has recently developed, for the first time, a series of mathematical solutions to problems involvinga C, mass subject to self-weight. He demonstrates that for such a case a semi-arch (Fig. 2) is stable. A corollary of this argument is that for a true C, d material a curved overhanging slope is possible and such an observation may well aid field identification of these materials. The shape of the curved slope face is however directly dependent on the C-value, and from the long-term point of view this is a most difficult value to establish with any degree of confidence. It is customary to measure C and 0 in some form of shear test—usually a triaxial compression test—on core specimens sampled from the rock, and as far as the author is aware the present case is the only one in which, as far as overall stability is concerned, such tests are

Jan 1, 1961

By J. A. L. Napier

This paper presents an overview of work carried out by the CSIR Division of Mining Technology and formerly by the Chamber of Mines Research Organization (COMRO) to quantify the behaviour of the stope fracture zone near deep level goldmine stopes. The motivation for this work is first reviewed in the context of the unsatisfactory status of current mine layout design criteria. Numerical methods to represent failure processes are reviewed briefly. Specific studies of microfracture processes are described as well as physical modelling experiments that can yield insights into deformation mechanisms. Modelling of stope scale deformation mechanisms are presented and considerations relating to elastodynamic modelling of the rock mass are described. The implications of this understanding in relation to prospects for active fracture zone ?engineering? are outlined and finally, the directions of future research work are proposed.

Jan 1, 1997

By AIME AIME

THE following paragraphs, constituting the concluding portion of the Annual Report of the Council for 1903, have been withheld from publication until now, in order to make them as accurate and complete as possible. They will be published in Volume XXXV. of the Transactions in their proper place at the end of the said Annual Report. Franklin Ballou was born in Pittsburg, Pa., May 29, 1845. He was the son of an old resident, Arthur Ballou, a manufacturer and wholesale dealer in vinegar. In early youth Franklin attended the Western University of Pittsburg, but left school at the age of 16 to become book-keeper for his father, upon whose retirement from business, in 1868, he associated himself with Walter C. Childs, of Pittsburg, in the manufac¬ture of furnace-grates and asbestos-cement for blast-furnaces. This firm was known as W. C. Childs & Co., and did a success¬ful business for several years. In 1869 Mr. Ballou married Miss May S. Wilson, daughter of Judge Wilson, of Lewistown, Pa. In 1876 he spent several months traveling in the West and studying the mining industry, which greatly interested him. In consequence of this journey, he wound up his business in Pittsburg and removed in 1877 to Georgetown, Colo., where for several years he conducted a sampling-works, and built up an extensive business as an agent for the sale of ores, besides engaging to some extent in mining enterprises. , It is said that he controlled at one time about one-eighth of the output of the Leadville mines. In the early 80's, he became Vice-President and General Manager of the Bimetallic Smelter at Leadville, of which Mr. David H. Moflat was the principal owner. This was practically the first successful demonstration of pyritic smelting in Colorado. Upon the sale of the works in 1897 to the American Smelting and Refining Co., Mr. Ballou retired

Jan 1, 1905

By E. Sharifi

Advanced Process Control (APC) has been one of the most beneficial tools in the past decades available to minerals processing industry. Low capital cost together with significant improvements in process optimization have made APC an attractive investment option for nearly all mineral processing units. During economic downturns, importance of process optimization becomes even more relevant as metal producers tend to target de-bottlenecking and process efficiency improvements rather than large-scale capacity upgrades. APC project clearly has a lot of potential to improve process performance but there are also some pitfalls to be identified and avoided in order to achieve a desired outcome. Above all, APC project implementation is collaboration between the system vendor and user. Targets for the optimization must be agreed together with the customer and process performance must be defined before and after the optimization project. Most importantly, performance of the process must be monitored on a continuous basis during and after the project and potentially improved further. This paper discusses Outotec’s experiences from various concentrator optimization projects. Some examples are discussed in more details; however, the main target is to present general guidelines enabling a successful APC project implementation.

Jan 1, 2014

Open cut mining of the Black Rock chalcocite ore started in 1963. A ground movement monitoring programme was commencing in the early stages of mining when signs of instabilityof the western wall became apparent. Eventually 100.000 cu vd, of overburden Were removed beyond the rim of the western wall in an attempt to stabilize the slope. Subsequent decpenlug and mining till the final batter angle of 45 resulted in deterioration and mining was stopped 38 ft short in the ulltimte design deplh of 520 ft.Investigations showed that the geology of the western wall , was a major factor in the instability of this wall. A block jointed model was made 10 illustrate some of the pehomena observed. Quallatative agreement was found between the model deformation and the field measurements obtained.The results of the monitoring programme clearly show the value of this work In respect to the conlrol of the mining operatIon...

Jan 1, 1968

By William B. Hughes

The rubber-sleeve core barrel was developed to improve core recovery from unconsolidated sands, where it is most difficult to obtain cores with conventional barrels. The use of a rubber-sleeve core retainer, together with other departures from clsual design, has required a considerable amount of testing to prove its op-erability. Tests run in shallow experimental holes and in drilling wells in the U. S. and Vemzuela have, to a large extent, proved the operation of the barrel. Internal mechanism troubles, such as sandbinding of the sleeve, have been largely overcome. Cores have been recovered from completely unconsolidated sands where conventional coring has almost been abandoned because of poor recovery. In addition to retaining the core until brought to the surface, the barrel gives a "packaged-ar-cut" core, which is coilverzient for handling and transportatiorz. In the initial work, drag blade cutters, roller cutters, and tungsten carbide insert cutters were usrd for cutting unconsolidated sands. Further bit head development is presently being conducted using diamond heads in unconsolidated sands where shaler, hard sands, and limestones are encountered in adjacent formations. Thir work should render the barrel capable of cratting and recovering most types of formations, possibly including broken and frac- tured fornlations. This development is being carried on in cooperation with a diamond bit manufacturer. INTRODUCTIO N For many years the oil industry has needed greater recovery of cores from unconsolidated formations. Conventional equipment has been used to core unconsolidated sands with little success. Specifically, a core barrel was needed which would recover unconsolidated sands in a condition that would give useful reservoir information. DEVELOPMENT OF 'THE RUBBER-SLEEVE CORE BARREL Basic Requirements of Unconsolidated Sand Corino The basic need was defined as a core barrel that would obtain a continuous unconsolidated core with sand grains in place as deposited in the formation. A preliminary survey of coring equipment and search of the literature pointed out the weaknesses of conventional core barrels. Laboratory tests using unconsolidated sand in a metal tube simulated actual sand movement into the core barrel during conventional coring. In conventional barrels the core sometimes crumbles and bridges, or fails under compressive column action, becomes oversize, and wedges against the walls of the inner barrel. The core barrel requirements established by the surveys and preliminary tests are as follows. 1. The core should be held to- gether as it is cut so it cannot crumble and bridge against the walls of the coring tool, care being taken not to permit damage from fluid circulation. 2. The core should be continuously supported as it is cut so it will not have to support itself in compression. 3. The core should be packaged in the barrel to retain an undisturbed condition during the trip out of the well. The packaging should be such that the core can be removed from the barrel and shipped to the core analysis laboratory without physical disturbance or alteration of fluid content by exposure to the atmosphere. Operation of the Rubber-Sleeve Core Barrel The rubber-sleeve core barrel (Fig. 1) meets the basic requirements for the recovery of unconsolidated sands.

By Colin Rawlings, Simon Pepper, Maria Karakitsiou, John Mathews, Peter Townsend, Russell Bowler, David Keeble, Christopher Darton, Scott Sadler

National Grid needs to maintain a connection between two existing electricity sub-stations (Beddington & Rowdown) in the Croydon (south London) area, and allow the replacement of two 275 kV cable circuits that are buried under roads. This is to be achieved using a single 400 kV cable circuit within a 10 km (6.25 mile) long, 3 m (9.8 ft) diameter high voltage cable tunnel which is being driven through water bearing Chalk, at depths ranging from 5 m (15 ft) to 80 m (262 ft), with four access shafts(12.5 m (41 ft) in diameter) ranging in depth from 10 m (31 ft) to 40 m (131 ft). The Chalk in this area acts as a source of public drinking water supply (PWS) and is protected by areas designated Groundwater Source Protection Zones. To minimise the groundwater risk the design and construction of the cable tunnel and shafts has paid particular attention to the construction materials used, including testing of these construction materials prior to use, developing construction methods (including the design of the Earth Pressure Balance TBM) and maintaining a groundwater monitoring & testing programme prior to and during construction to ensure the integrity of the Chalk aquifer is maintained as a drinking water source. This paper describes the tunnel &shaft design and construction in relation to these particular groundwater environmental issues which set new precedents for tunnel assessment, design and construction requirements in the United Kingdom.

Jan 1, 2007

By Duberney Hincapié-Ladino

O presente trabalho estuda os parâmetros de permeabilidade de hidrogênio de um tubo API 5L X80, e uma chapa de aço grau X80, onde a principal diferença está na composição química, o primeiro contém 0,07%C e 0,04%Nb e o segundo 0,04%C e 0,102%Nb. As amostras foram cortadas com espessura de aproximadamente 1 mm, lixadas e recobertas com um filme de níquel, em uma das faces. Nos ensaios de permeabilidade foi utilizada uma célula modificada tipo Devanathan-Stachurski, com a solução A da norma NACE TM0284, com injeção de H2S no lado de geração e 0,2M NaOH no lado de detecção. As curvas de corrente em função do tempo obtidas passaram por tratamentos matemáticos (método tlag), permitindo a obtenção dos parâmetros de difusividade aparente, concentração máxima de hidrogênio e número de traps (sítios de ancoramento). Tais parâmetros mostraram-se iguais para os dois materiais. As curvas foram normalizadas e modificadas de maneira a eliminar o efeito da espessura das amostras. Estas novas curvas foram comparadas com o modelo teórico da segunda lei de Fick. A comparação evidenciou que o procedimento inicial para a obtenção dos parâmetros de permeabilidade mostra-se eficiente e vantajoso por apresentar maior praticidade. Pôde-se concluir que a semelhança no comportamento dos parâmetros de permeabilidade foi devida às similaridades nas suas microestruturas. Os resultados obtidos no presente trabalho evidenciam que o tipo e quantidade de traps nestes materiais são determinados pela microestrutura.

Aug 17, 2017

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed. The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grad~, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the fmal cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure 1."

Jan 1, 2003

By Thierry Sempere, Jorge Acosta

En este trabajo empredemos una síntesis preliminar de la evolución geológica y tectónica que se puede reconstruir actualmente en base a las investigaciones en curso, junto con el análisis de datos metalogenéticos disponibles a la fecha. Se hace énfasis en el magmatismo dado que la gran mayoría de los depósitos minerales se relacionan con fenómenos magmáticos occuridos en un arco de subducción.

May 1, 2008

By Michael J. Lehnen

Slurry diaphragm walls are commonly used as both temporary excavation support walls, and permanent structural walls, for circular shafts and long rectangular structures (such as underground subway stations); however, they are not commonly used for more compact rectangular or square shafts. In these instances, a second wall is typically cast inside the slurry walls to form the permanent structure. This paper discusses the approach used on the Silicon Valley Rapid Transit Project in California to analyze these compact rectangular types of structures for static and seismic loading, and to determine whether or not slurry walls can be confidently used as both the temporary and permanent walls for two tunnel ventilation shafts.

By Curtis Wilson

FROM the results of his investigation of the hardenable copper-nickel-silicon and copper-cobalt-silicon alloys, M. G. Corson1 explained the dispersion-hardening effect by assuming the precipitation of the inter-metallic compounds nickel silicide and cobalt silicide, and on this basis he constructed diagrams for the pseudobinary systems copper-nickel silicide and copper-cobalt silicide. A consideration of these diagrams and of the factors that exert such an important influence upon the rate of precipitation, such as degree of supersaturation, nucleus number and rate of diffusion, leads to the expectation that the rate of precipitation of the silicides on reheating the quenched solid solutions at temperatures below the alpha-phase boundary should increase continuously as the reheating temperature is raised. The present investigation shows that while this rate does increase with the reheating temperature in a general way, it does not do so continuously. Supplements to Corson's diagrams are offered, showing the discontinuities, and slight modifications in the solubility curves are suggested.

Jan 1, 1933

The key to the successful debt funding of a new mining project, whether in economically established or developing nations, is the submission of a comprehensive feasibility study. The feasibility study forms the basis from which the resource banker can construct financial models which govern the amount of available funds, the conditions which control the supply of such funds and the time period over which the loan may be repaid. The bank will wish to ensure that the feasibility study is the best representation and confirmation of reality possible because this model is the basis of the loan security package. Thus the study will be vigorously interrogated by independent experts in all its elements including the ore reserve, mineability, metallurgy, operating and capital cost profile, environmental factors and management. A well constructed feasibility study, undertaken by well recognised and respected independent consultants can save the client company a great deal of real and opportunity costs especially in relation to project timing. Once constructed and operating, the mining project may face one or more completion tests in relation to the loans provided. The genetics of such tests often relate to either the ability of the operating company to become solely responsible for the repayment of the loan or to be rewarded by lower interest rates or some other mechanism. Strong professionalism, accessible records, good checking procedures and high quality, competent site management will greatly assist the client company passing these tests. A record of well established technical competence with its bankers may well assist a company in the establishment of a mezzanine loan for the early development of its next project, thus allowing an earlier return of dividends to shareholders.

Jan 1, 1995

Tunnelling under squeezing ground conditions poses significant challenges. There are fundamental differences in the choice of support for mining as opposed to civil engineering. This paper reviews ground support strategies that have been used to control large deformations in mining excavations based on field data from five different mines in Australia and Canada. Recommendations are made for improved ground control strategies in squeezing rock conditions.

Jan 1, 2008