Search Documents

By E K. Leeka

Process control limitations have led to suboptimal performance of the crushing section of Sishen MineÆs Jig Plant. The performance of the PID (proportional-integral-derivative) controller implemented during commissioning was hampered by the relatively small buffer capacity between the crushers and screens. The inability to maintain the tertiary crushing chamber under full choke conditions lead to inefficient crushing and reduced crusher product cubicity.Model predictive control (MPC) was implemented in the tertiary crusher plant in May 2012 and resulted in a throughput improvement of six per cent in its first month. The controller was further optimised and indicated a throughput improvement of 16 per cent during on/off testing in July 2012. The throughput improvement is attributable to the finer crusher product resulting from operating the crusher under full choke conditions and controlled feed rate to the tertiary crusher plant screens. The next step is to couple the model predictive controller, automated gap control system and an economic optimiser to ensure maximised throughput and value from the resource.CITATION:Leeka, E K, 2013. Performance of model predictive control on the crushing circuit at Sishen Mine, in Proceedings Iron Ore 2013 , pp 417-420 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The Role of the Drilling Contractor BY FERRIS E. SAINSBURY Ron Haxby, Occidental Minerals What is the best method for drilling a 12-in. diam hole to a depth of 1200 ft and maintaining the deflection within 25ft from vertical? Ferris Sainsbury: In order to drill a 12-111. hole down to 1200 ft, In most places you would have to employ a rotary tricone bit With a down-the-hole hammer, I expect by that depth significant Inflows of water would be experienced Even with foams, we would not be able to get the water out of a hole of that diameter So the down-the-hole tricone method of drilling would be best. To keep it straight, we would probably employ the largest square drill stem compatible with the diameter of the hole. Ron Haxby: Is it common in drilling contracts to put in a vertical hole clause? Ferris Sainsbury: You can put in the vertical hole clause Ron Haxby: Does it cost more? Ferris Sainsbury: Normally, if the hole deviates, the driller can correct it with deflection wedges and will charge it back to you at cost, plus 10% or somewhere along that range Any drill hole has a tendency to go perpendicular to the dip, and there are times when stabilization systems are not successful in preventing the hole from turning into the dip of the formation. The only solution, in this situation, is to go in with an oriented wedge and kick the hole back out.

Jan 1, 1979

By Jedson Alessandro Damasceno

Atualmente, a maioria dos pátios utilizam recuperadoras com roda de caçambas para remover o minério das pilhas de estocagem. Tipicamente, estas máquinas são operadas manualmente, com todos os movimentos controlados por operadores, o que faz com que o processo seja totalmente dependente de sua experiência, tornando difícil manter o processo em operação ótima. Para alcançar uma melhor performance, foi implementado um sistema automático que controla todos os movimentos de recuperação. Um importante desafio encontrado durante a construção dessa solução foi a de estimar a taxa de recuperação em tempo real, uma vez que esta informação é essencial para o algoritmo que controla o movimento de giro da máquina. Uma medição real dessa taxa está disponível, mas, a balança localizada na lança fica distante da roda de caçambas. Em outras palavras, a medição real está disponível com um grande atraso (aproximadamente 13 segundos). Este delay é inaceitável para o algoritmo de controle que necessita de uma medida em tempo real da taxa de recuperação na roda de caçambas. Diante disso, foi necessário implementar um sensor virtual. Este sensor foi implementado usando um sistema neuro-fuzzy para estimar a taxa de recuperação em tempo real utilizando outras variáveis disponíveis, tais como a pressão na roda de caçambas e medidas de penetração obtidas por radares. As estimativas obtidas ficaram muito próximas dos valores reais, e este sensor pôde então ser utilizado pelo algoritmo de controle.

Aug 17, 2017

By Pedro Hugo Tumialán

El presente texto señala la composición metalogenética de la Cordillera de Huayhuash (Ancash). La Cordillera de Huayhuash que es parte de la Cordillera de los Andes, es una importante provincia metalogénética polimetálica del Perú. En este sentido, dicha Cordillera constituye una franja de yacimientos polimetálicos de zinc, oro, plomo, plata y cobre, los cuales se estructuran sobre yacimientos filonianos y tipo estrato ligado. Asimismo, los filones no tienen preferencia de roca para su minetalización, los mantos se ubican en horizontes calcáreos del Cretáceo. Asimismo se describe la extensión, fisiografía, estratigrafía y los yacimientos de contacto.

Mar 1, 1980

By Georg Petersen

El presente artículo describe la actividad petrolera realizada durante el año 1962. En 1863 el Gobierno del Perú derogó al Ing. A. E. Prentice el estudio de las posibilidades petroleras de Piura y Tumbes, a través de la perforación del primer pozo de petróleo en Zorritos a través de herramientas imperfectas. Ante tal éxito, en 1864 Lama y Rudens gestionaron que se constituya en Nueva York la "Compañía Peruana de Petróleo". Posteriormente, doce compañías petroleras han desarrolado trabajos de exploración y nueve se encuentran en estado de producción. En este plano tenemos a Belcom Petroleum Corporation Perú, Cerro de Pasco Company, Empresa Petrolera Fiscal, Compañía peruana de Petróleo "El Oriente", International Petroleum Company, Mobil Oil Company, Mobil Oil Company of Perú, Compañía de petróleo Ganso Azul, Peruvian, entre otros.

Jul 1, 1963

By Georg Petersen

El presente artículo describe la actividad petrolera realizada durante el año 1962. En 1863 el Gobierno del Perú derogó al Ing. A. E. Prentice el estudio de las posibilidades petroleras de Piura y Tumbes, a través de la perforación del primer pozo de petróleo en Zorritos a través de herramientas imperfectas. Ante tal éxito, en 1864 Lama y Rudens gestionaron que se constituya en Nueva York la "Compañía Peruana de Petróleo". Posteriormente, doce compañías petroleras han desarrolado trabajos de exploración y nueve se encuentran en estado de producción. En este plano tenemos a Belcom Petroleum Corporation Perú, Cerro de Pasco Company, Empresa Petrolera Fiscal, Compañía peruana de Petróleo "El Oriente", International Petroleum Company, Mobil Oil Company, Mobil Oil Company of Perú, Compañía de petróleo Ganso Azul, Peruvian, entre otros.

Jul 1, 1963

By Frank Cipriani

El presente texto describe los detalles técnicos de los cambios realizados en la mina San Rafael para adaptar el método de explotación de taladros largos en cuerpos a vetas angostas y así contribuir a la industria minera con la experiencia vivida, y mejorar sus resultados operacionales en la compañía. Los cambios implicaban la implementación de nuevos parámetros operativos en las labores de producción, los cuales debían ser de escalas menores a los que tradicionalmente se venían trabajando, así como la adaptación del personal encargado de la dilución hacia los nuevos estándares y procedimientos operativos propios de un minado en vetas angostas.

Sep 21, 2013

By W. W. Adams

The United States Bureau of Mines, in cooperation with the National Send and Gravel Association conducted a safety contest in 1929 Among producers of sand and gravel. Only 26 plants were enrolled, as the contest was late getting under way. It is hoped that a ranch larger number of plants will be represented in the safety competition of 1930. Two trophies, both of which were provided by Rock Products magazine, were awarded at the end of the contest; one trophy was given for the best safety record among plants working 100,000 or mare man-hours during the year and the other for the beat record among plants working less than 100,000 man-hours. The trophies were presented to representatives of the winning, companies on January 29, 1930, at the annual convention of the National Sand and Gravel Association at Memphis, Tenn.

Jan 1, 1930

By Rafael Henrique Alves Gomes

A automação em processos industriais agrega qualidade, padronização e segurança aos produtos e pessoas envolvidas. Entretanto, as demandas de mercado, custos agregados e a concorrência exigem melhorias que podem ser alcançadas através de métodos de otimização. Este artigo apresenta algumas metodologias e ferramentas para otimização de processos industriais que visam desvincular a obrigatoriedade de que Técnicas de Controle Avançado em métodos de otimização são a única solução capaz de oferecer resultados satisfatórios para aumento de produtividade. Os recursos expostos abordam a gestão de malhas de controle, gestão de alarmes e o cálculo do indicador global de eficiência, o OEE.

Aug 17, 2017

By Paul T. Allsman, William H. King

This paper describes the mineral deposits and discusses mining and milling methods and related operating conditions in an important gold , silver , lead , and zinc producing area in Ouray , San Juan , and San Miguel Counties , Colo . , embracing 250 square miles . The area is extremely rigged , ranging in altitude from 8,000 to 14,000 feet . White men first penetrated the area in 1860 , when a group known as "Baker's party " reached the Animas River at the present site of Silverton . Difficulty with the Ute Indians and severe winter conditions forced the group to leave and discouraged prospecting until 1870 when a second party reached the area and succeeded in producing 27 tons of ore yielding $ 150 a ton in gold . In 1874 , a treaty with the Indians opened the way for settlement , and mining was established . The total production of recovered gold , silver , copper , lead , and zinc from 1873 to 1947 in the three counties is valued at $347,057,047 . The greatest amount of the total production of metals has come from quartz veins in a series of volcanic flows and tuffs covering the area and comprising a blanket 4,000 to 6,000 feet thick . The igneous rocks were laid down upon an old , erosion surface and are underlain by Paleozoic and Mesozoic sedimentary rocks and pre - Cambrian metamorphic rocks . The entire series has been intruded in late Tertiary time by volcanic dikes and larger intrusive masses . Because of the great differences in relief generally , mining is con-" ducted through long adits to a depth of nearly 3,000 feet below surface in places . Walls of the veins generally stand well , and shrinkage stoping is the most common method of mining . As virtually all of the ore is sulfide below the zone of oxidation , flotation is the common method of milling . Generally , where gold is important , provision is made for its removal by jigs . Bulk concentration of the sulfides is practiced at smaller mills , but the larger operations make a selective lead and zinc concentrate or a lead , zinc , and copper . concentrate . ·

Mar 1, 1950

By Jorge Injoque Espinoza

El presente trabajo describe la mineralogía de la plata, cobalto, níquel y oro en los principales depósitos de cobre y hierro de la faja costera. Para la descripción de los depósitos se revisan los trabajos de Injoque, así como en diversos estudios de mineragrafía, microsonda y geoquímica.

Nov 1, 1985

By Taehong Kim, Carl Pannuti, Nikolas Sokol, Walter Herrick

BACKGROUND This paper discusses work performed as part the rehabilitation of the gravity flow section of the New Croton Aqueduct (NCA) during an approximately two year period between 2004 and 2006. The goal of the project was to restore the gravity flow section of the NCA to optimal operating condition, extending the lifespan of this significant water supply for the New York City metropolitan area. Rehabilitation of the NCA was purposely scheduled before the completion of the new NCA Water Treatment Plant now under construction (Figure 1). The NCA is a 3.73 to 4.34 m (12.25 to 14.25 ft) diameter brick-lined circular andhorseshoe shaped water tunnel constructed between 1885 and 1891. The NCA conveys water for approximately 50 km (31 miles) by gravity and pressurized flow from the New Croton Reservoir in Westchester County, NY to distribution and reservoir points along its alignment, terminating at a distribution station at 135th Street and Convent Avenue in Manhattan, NY. Prominent features of the NCA include a large intake facility at New Croton Reservoir, 38.6 km (24 miles) of gravity flow horseshoe shaped aqueduct, 11.3 km (7 miles) of pressurized flow circular aqueduct, 2 siphons, and 36 open shafts and headhouse chambers which are used as sampling, access and blow-off locations. Until a partial inspection in 1982, the NCA had flowed continuously since its completion nearly 100 years prior. Flow tests have confirmed that the NCA can convey up to 12.7 m3/s (290 mgd) (Figure 2). Cover depths of NCA vary considerably, ranging from a few to hundreds of meters, typically of hard rock. Primarily mined using means conventional for the late1800s, construction of the NCA also employed cut and cover methods in several low-lying sections of the alignment, totaling approximately 1.6 km (1 mile). The NCA crosses through numerous lithologic changes, fault/shear zones and under several significant water bodies including the Pocantico, Saw Mill and Harlem Rivers and the Tarrytown Reservoir. The NCA passes under the Harlem River as a siphon at a depth of approximately 122 m (400 ft) below grade (Figure 3). Soon after construction the Aqueduct Commission Reports on the New Croton Aqueduct documented prominent defects such as large voids behind the lining. More recently, large-scale inspections of the gravity flow section performed during the 1990sand a 2004 inspection of portions of the pressurized sections of the NCA have revealed additional defects such as open and/or deteriorated masonry joints/cracks, leaks ranging from trickles to several liters per minute into and out of the NCA, missing bricks, formed openings, and in one place, a rupture through the liner with discernable

Jan 1, 2007

By Eli Robinsky

La disposición de relaves es importante en tanto busca proteger y rehabilitarlo el medio ambiente a un menor costo posible. En ese sentido, el presente texto describe el método de descarga densificada como el más adecuado puesto que logra una solución más aceptable desde la perspectiva ecológica. El método ofrece la ventaja de aumentar la capacidad de las zonas existentes para el almacenamiento de los relaves, sin requerir de la ampliación de las presas perimetrales.

Sep 1, 1983

It is difficult, and probably inadvisable, to frame rigid rules for the valuation of alluvial deposits, for such deposits are very diverse in type, varying, for example, according to the mineral sought and according'to the complexity of the deposit which, on one hand, may be a narrow welldefined alluvial strip at the bottom of which is a continuous mineral lead, or, on the other, may be a broad alluvial flat with discontinuous patches of the valuable mineral occurring at different levels throughout the alluvium.However, some definite procedure in valuation must be adopted when dealing with anyone deposit, and the fundamentals of such a procedure are applicable to almost all alluvial deposits.The methods described in this paper are based very largely on the valuation of a specific deposit and, although an attempt has been made to keep the discussion as general as possible, it contains some statements which, if traced to their origin, spring from the writer's association with that deposit. Such statements must be interpreted with sufficient flexibility to be appropriate to whatever area the reader may have in mind.The subject of valuing an alluvial deposit falls naturally into two divisions: The valuation of each borehole; the valuation of the deposit as a whole. The following discussion is therefore dealt with under these two headings.Some general matters are mentioned in a third section.

Jan 1, 1950

By Brian Hart, Stamen Dimov

"The Time of Flight Secondary Ion Mass Spectrometer (ToF-SIMS) is unique in that it measures the outermost atomic layers of any material. The technique is particularly suited for determining surface chemical composition of mineral particles. It is most commonly used as a diagnostic tool to measure mineral surface chemical variability in plant and bench top flotation separation processes. Recently, research towards understanding the full capability of the instrument has resulted in the development of new diagnostic applications related to various Au extraction technologies and the development of the ToF-SIMS as a predictive tool for assessing the chemical reactivity of the ore.In this paper we will present a brief review of the ToF-SIMS technique with recent advances in instrumentation and methodologies including:•,?recent developments and advances towards a semi-quantitative approach to the evaluation of mineral surface modifiers (ex. Cu),•,?flotation case studies investigating activator, depressant and collector loading variability within a flotation process,•,?the recently developed chemical reactivity test which we believe has the potential to predict the behaviour of minerals in a flotation test in response to chemical transfer during grinding,•,recent applications for determination of surface Au preg-robbed in carbonaceous materials.A portion of this material has been recently presented at the COM 2009 meeting and at SIMS XVII (see Dimov et al 2009 and Hart et al, 2009).INTRODUCTIONIn flotation seperation surface chemistry is the principal determinant for selective separation of the various mineral phases (Ralston, 1994, Smart et al, 2003). Determination of this hydrophobic/hydrophilic balance by particle therefore requires correct identification and selection of the particular mineral phase(s) followed by a statistical analysis of the surface chemical characteristics of the particles with an estimation of the spread of values (Smart et al, 2003)."

Jan 1, 2010

By Henry Brañes, Luis Lazo

En los últimos diez años, las operaciones mineras se han enfocado en incrementar su producción, pero han descuidado el estricto control de construcción y operación de componentes mineros, tales como presa de relaves, pilas de lixiviación y botaderos de desmonte. Asimismo, debido al cambio climático, la intensidad de las lluvias se ha modificado, por lo que se tienen eventos de lluvias atípicas de altas precipitaciones en tiempos cortos. Así, estos cambios en el balance de aguas a tratar han evidenciado que las plantas de tratamiento, por los grandes volúmenes de agua a tratar, han quedado con capacidad restringida en el proceso de sedimentación de flóculos con metales pesados. El artículo analiza la aplicación de los equipos centrífugos en la industria minera; en especial, su aplicación en el tratamiento de efluentes mineros, con la finalidad de mejorar la eficiencia y desempeño del proceso de sedimentación y lograr así el cumplimiento de las regulaciones ambientales.

Sep 20, 2019

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

The Electricity Generating Authority of Thailand (EGAT) Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 Mt of lignite annually to generate 2400 MW of electricity. The surface mine pit covers is 4 km by 7 km with mining depths ranging up to 260 m. A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope occur often due to the existence weak planes such as faults and bedding, and the weak mechanical properties of the rocks. Hence, 200 m to 300 m boundaries of rock block including coal seams are left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope. Moreover, the mined coal seams are very thick and their thickness range from 15 to 30 m.This paper discusses the application of multi-slicing highwall mining system with stowing to this very thick coal seam left around large pit slopes by means of numerical analysis.

Dec 6, 2010

By Roney Eduardo Lino

As ocorrências recentes de terremotos em diversos países têm incentivado o desenvolvimento de vergalhão com características sísmicas, ou seja, que apresente elevada resistência mecânica sem que a ductilidade seja deteriorada. Este trabalho propôs uma abordagem investigativa dos principais fenômenos metalúrgicos atuantes no processo de laminação a quente de vergalhão em rolo Ø20 mm. Foi utilizado um modelo matemático de evolução microestutural com equações capazes de prever a quantidade de elementos microligantes ao longo do processo, a cinética de precipitação e o comportamento do tamanho de grão austenítico durante todo o tempo de laminação. Os resultados industriais de microestrutura e propriedades mecânicas convergiram com os resultados previstos pelo modelo. Com combinação do modelo matemático com testes industriais foi possível obter vergalhão com limite de escoamento superior a 600 MPa e alongamento de 15 %.

Oct 30, 2017

Rational decision making is generally perceived by managers of operations to be a delicate process of committing large sums of money and putting other people's life at risk. Consequently most managers may argue that the decision process requires good judgement, intuition and extreme caution; and not one easily made through the use of fancy mathematical algorithms and computer programs. The advent of artificial intelligence and expert systems in the computer industry combined with recent technological innovations in mathematical and economic problem solving is sure to change this perception. PARETO OPTIMALITY is an economic and a mathematical optimisation concept applied to solving real life operational problems; and one that the current volatile economic forces would require managers to employ because it is virtually real. REALISMM is a computer software package developed using the principles of Pareto optimality, dynamic programming, optimal clustering of information and decision maker interaction to generate decision maker preferred solutions. REALISMM has scope for artificial intelligence and expert systems application for cases where the decision maker is unsure about his objective preferences.

Jan 1, 1993