Search Documents

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By Joaquim Luiz Monteiro Barros

Este trabalho tem como objetivo principal apresentar de forma didática e com um exemplo prático a viabilidade da aplicação da tecnologia de recuperação de calor no sinter cooler, com a finalidade de gerar energia térmica (ar quente, vapor, água quente, etc) reduzindo o consumo final de combustíveis na planta.

Aug 17, 2017

By Kihong Park, Matthews C. Habjan, Arthur L. Miller

New Mining Safety and Health Administration (MSHA) regulations limit the mass concentration of airborne diesel particulate matter (DPM) or, more specifically, the concentration of elemental carbon (EC), in underground mines. The mine operators are responding by introducing a variety of controls to reduce DPM in the mines, potentially including the evaluation of new maintenance procedures to reduce underground mine vehicle emissions. There is currently a lack of an inexpensive and dependable method to directly measure the DPM concentration emitted from the vehicle tailpipe. To that end, this work demonstrated a simple field portable method for estimating the mass concentration of elemental carbon exiting the tailpipe of a diesel engine using a direct reading photometer. Simultaneous measurements of tailpipe exhaust were made with a Thermo Electron Personal DataRAM 1200 photometer (particulate mass concentration based on light scattering) and by analyzing PM2.5 and PM1.0 samples collected on quartz fiber filters using the National Institute of Occupational Safety and Health (NIOSH) method 5040 (mass concentration of EC via thermal-optical method). Results indicate surprisingly good correlation (R2 ) 0.97) of the two methods when the data are adjusted for relative humidity (RH) and corrected using an empirically generated calibration factor. Although preliminary, it may be possible to implement this method in maintenance shops to monitor emission trends and to compare emissions of various vehicles in a fleet. Such data will be useful for fleet planning to meet new air quality standards.

By Camila Lourenço Soares

A produção de aço no mundo está a cada dia mais competitivo, com isso as indústrias siderúrgicas tem desenvolvidos projetos com foco na melhoria da qualidade dos aços e na redução dos custos dos processos de fabricação. Este trabalho descreve as melhorias realizadas no processo de lingotamento contínuo, com foco na redução do desvio de placas por desobstrução dos veios da MCC 2. Esta melhoria consistiu na modificação do sistema de controle e injeção de argônio dos veios durante o lingotamento. A implementação dessas ações propiciou um melhor controle na injeção de argônio no sistema de válvula gaveta, reduzindo significativamente as obstruções do veio por deposição de alumina. Hoje, com os resultados alcançados na MCC 2 perduramos entre as melhores práticas nacionais. O trabalho foi realizado sem investimento contribuindo com a redução do custo de transformação do aço em placa.

Aug 16, 2017

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector's item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy's slate left most classrooms before the oldest of us were born.

Jan 9, 1964

By Wesley T. Holmes

This report describes the second phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected synthetic slag compositions in the Ti02 -A1203 -FeO-Si02 -CaO-MgO system. Both the hot-stage microscope and the strip furnace (melting-holding-quenching technique) were used during test procedure to determine the effects of CaO, MgO, and SiO2 on the liquidus temperature of slags. The liquidus temperatures of slags studied ranged from 1,241° to 1,900° C. The lowest liquidus temperature for each Ti02 plus A1203 plus FeO weight-percent generally occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. In this investigation substitution of either CaO or MgO for SiO2 and MgO for CaO raised the liquidus temperature of more than 50 percent of the reported base slags when Ti02, A1203, and FeO contents were held constant. The results of this investigation may serve as guidelines for determining flux requirements in smelting a wide variety of titaniferous magnetite concentrates or ores.

Jan 1, 1968

By D. P. Venter

When Oryx Mine down-scaled in 1994, focus was placed on development, with the primary aim being the exposure and proving of ore reserves. In order to achieve this aim, development ends had to be advanced to reef at the maximum possible rate. This in turn called for support methods which could keep up with the advancing faces, taking up minimum space and time for installation, while providing on the face a real coverage and effective long-term support. In the majority of the development ends which were located in fairly competent ground, the grouted rod development support proved to be adequate until such time as secondary support in the form of meshing and lacing could be installed. The ends developing towards the eastern boundary of the mine, especially in the ?C? block, encountered extremely adverse ground conditions due to the presence of smectite zones within the footwall quartzites. Smectites are a group of montmorillonite clay materials, mainly composed of hydrous aluminosilicates. They occur as minute platy crystals in the rock mass and are especially notable for their ability to absorb liquids. Generally, the zones are found in between the bedding planes of the host rock, and may vary considerably in thickness over short distances. Wherever the smectites were exposed by the development blasting, the rockwalls weathered as the smectites absorbed water and the condition of the tunnel rockwalls deteriorated rapidly. When the smectites were left exposed and allowed to weather, it became almost impossible to install secondary permanent support such as meshing and lacing at a later stage. To minimise the exposure time and subsequent deterioration of the smectite zones, it was recommended that all development ends encountering smectites be shotcreted as soon as possible after blasting. In developing a shotcreting support methodology, both a drycreting and wetcreting system were investigated. The situation at the time ruled out the use of a wetcreting system on the basis of the extensive and costly infrastructure required, as well as its limited manoeuverability. Instead, it was decided to opt for as maller scale but more manoeuverable drycreting system. The system utilized a number of portable drycrete machines with pre-bagged cement, which could support several development ends in close proximity. Initial trials using normal 30 MPa shotcrete on 19level proved successful and the system was implemented.

Jan 1, 1998

By J. Haynes

Coal mines in the eastern US often use sloped shafts as production beltways for ore removal, as means of access for supplies, and for ventilation. These structures are usually completed with the help of a contractor. In late 2011, Frontier-Kemper Constructors was engaged to build a slope for a coal mine in southern Indiana. Although the site was located in familiar Illinois basin formations, the geology proved to be very difficult. This paper describes some of the challenges faced during excavation of this slope and the methods used to overcome them, including changing the method from conventional drill and blast to cutting with a continuous miner.

Feb 27, 2013

By Meliton M. Garcia

The volume of gases produced in major and trace amounts following the detonation of two water gel and two emulsion explosives in a mine were determined. The volume .of the major gases (CO, CO2, NO, and NO2) was measured immediately following detonation, during the mucking operation, and following the removal of the muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The volume of each major gas per pound of explosive (ft /lb) ;ranged as follows: CO, 0.0424-0.3231; CO , 0.6819-1.5632; NO, 0.0129-0.1320; and NO2, 0.0019-0.1111.. An approximate average of 95% of the gases produced was found in the test chamber immediately following the detonation, while less that 2% was found in the chamber following removal of the muck. Benzene was the most significant compound found to occur in trace amounts. Scaling tests performed with a water gel and an emulsion explosive suggest that the volume of the gases per unit mass of explosive detonated diminishes as the amount of explosive per blast increases.

Jan 1, 1986

By Jr. Sayre

Results of studies of reservoir and wax-precipitation temperatures relating to wax deposition in the reservoir of the Bradford oil field are presented in this report. During 1949 and 1950 Bureau of Mines engineers made temperature measurements in 42 wells, which indicate that the Bradford Third-sand temperatures range from 59.7° F., at 1,150 feet, to 71.9° F., at 2,040 feet. Reservoir temperatures measured at the same depths in newly drilled wells and oil-producing wells differed as much as 4.5u F. Injection-well temperatures measured during water injection showed that the temperature of the water entering the sand was 11.5° F. lower than reservoir temperatures before injection. The cooling in the formation resulting froth the injection of low-temperature water was 11.5° F. in the vicinity of the injection-well bore, and a maximum of 2.1° F. 200 feet from the injection well. Sand temperature, after 5 months of water injection, was reduced 1.5° F. 90 feet from water-injection wells. The temperature at which wax begins to precipitate from solution in crude oil was determined at atmospheric pressure for 26 samples and ranged from 51° to 67° F. Oil samples from wells producing no water had wax-precipitation temperatures ranging from 51° to 58° F. and wax contents from 2.20 to 2.97 weight percent, whereas the samples from wells producing water and oil had wax precipitation temperatures ranging from 580 to 67° F. and wax contents from 2.57 to 3.42 weight percent .

Jan 1, 1952

By Fabrice Mathieu

The Cutter Soil Mixing (CSM) provides a cost effective solution for the rapid construction of retaining and cut-off walls using new equipment developed from diaphragm wall cutter technology. CSM consists of cutting and mixing drums mounted on compact hydraulic motors. Soletanche Bachy CSM has been designed to leave the space above the tool free, thereby mixing the soil efficiently during all the phases of the wall construction, with high penetration rates. The precise positioning and verticality of the wall is achieved using a kelly bar and full monitoring. Soletanche Bachy CSM is a versatile equipment which can be mounted on various carriers: pile rigs, hydraulic crane, carrier equipped with telescopic mast. The major phases of Soletanche Bachy CSM development are presented, including the results of an extensive trial carried out in Le Havre (France). The soil consists of hydraulic fill with soft soil lenses overlying sandy deposits. 20m deep panels were constructed to support a rectangular shaft. During the construction, and after its completion, the shaft was subjected to an extensive series of tests followed by a partial excavation. The paper discusses also the future development of the technique and its potential applications.

Jan 1, 2006

By Donald H. Koch

The project investigated the impacts of coal and mineral storage piles on both ground and surface water quality. The study consisted of two major tacks, Task 1 had two phases. The first phase was field investigations in which ten cons and mineral stockpile sites (5 coal, 5 mineral: phosphate, lead, copper, iron, uranium) across the country were visited to determine the actual impart of coal and mineral stockpiles on writer quality. The second phase of Task I was a series of leaching experiments in which drainage from the ten coals and minerals was controlled and monitored to survey the extent to which storage piles release toxic ions to ground and surface waters. Task IT was n review of pollution abatement techniques with three generic treatment examples applied to lead-zinc ore, eastern coal, and uranium ore stockpile leachate. Major conclusions drawn from the completion of Tasks I and II include: water quality impacts are site specific, there is n high correlation between sulfide content of u material and its solution potential, and the selection of the best treatment alternative for n specific coal or mineral storage area must be based on site-specific criteria, pilot studies on representative leachate samples, and sound engineering design.

Jan 1, 1982

By Filipe Sathler

O projeto CR298 se iniciou no final do segundo semestre de 2014 quando o Coque Rate (CR) médio era de 351,0 kg/t. A meta definida foi de atingir média mensal de CR de 298 kg/t em dezembro de 2016, permitindo aumento de produção com alta taxa de injeção de carvão PCI, porém, com baixo Fuel Rate, garantindo competitividade de mercado. Sendo assim, foi desenvolvido e divulgado um novo modelo mental de operação, processo, manutenção e gestão, envolvendo toda a área de Redução, Utilidades e Aciaria. Várias premissas técnicas foram estabelecidas com um plano de ação detalhado para garantir estabilidade no processo dos altos fornos de forma a obter este resultado. A meta foi atingida antes mesmo do planejado: CR 291,3 kg/t em Maio de 2016 e em 2016 a média anual foi de 297,0 kg/t, com Fuel Rate de 484,4 kg/t.

Oct 30, 2017

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By C. Jay Hodgson, P. J. MacGeehan

"Of the 135 current or past-producing 'gold-only' mines in the Superior Province of the Canadian Shield which have produced more than 100,000 tons of ore, the 33 mines which have produced one million ounces or more of gold have accounted for over 84o/o of the total production of 137 million ounces. The published literature on these 33 deposits was reviewed in order to determine the geological setting of the mineralization on a regional (mining camp) and local (mine) scale. The dominant rock types underlying the mining camps are mafic, variolitic, tholeiitic volcanic rocks with a significant ultramafic (komatiitic) component, and clastic and/ or exhalative sedimentary rocks. Felsic volcanic rocks are generally subordinate. Most mining camps are located at or near the top of the mafic-ultramafic sequence, and generally there is a major sedimentary-volcanic contact present which may be 1) a stratigraphic superposition of volcanic and sedimentary units, 2) a rapid, along-strike gradation from dominantly volcanic to dominantly sedimentary units due to facies change, or to the formation of structurally controlled sedimentary basins during volcanism, or 3) frequently (at 40o/o of the camps) a juxtaposition of sedimentary and volcanic sequences across a major fault zone or 'break', which in many instances may represent a reactivated, syn-volcanic basin-margin fault.In contrast to the regional setting, on a local or mine scale over 90o/o of the 33 mines contain felsic intrusions and/ or extrusions within mine workings. The felsic rocks may be quartzbearing (commonly quartz-feldspar porphyries) or dominantly quartz-free (commonly feldspar porphyry syenites or monzonites), and appear to have been emplaced in two different depth-zone environments: an epizonal intrusive environment, and a volcanic vent environment. Although the distinction between epizonal intrusive and volcanic intrusive-extrusive rocks is uncertain in many deposits, the two are tentatively separated on the basis of the grain size of the rock matrix (medium to coarse grained vs aphanitic to fine grained), homogeneity (multi-phased and/ or compositionally zoned vs compositionally homogeneous), and the shape and relationship to stratigraphy of the igneous body (circular or oval in cross section, and cutting the stratigraphy at a low angle vs lenticular and either stratiform or cutting the stratigraphy at a high angle). In addition, felsic intrusions of the volcanic environment commonly grade into tuffs or breccias of extrusive origin, whereas epizonal intrusions do not.Stratiform ore zones of possible exhalative sedimentary origin appear to be confined to deposits in which volcanic felsic rocks are present, and are absent from deposits in which only epizonal felsic intrusions are present. Pervasive carbonate- rich alteration, commonly in roughly stratabound zones of regional extent, and carbonate-rich chemical sedimentary rocks are present in over three-quarters of the deposits containing quartz-bearing felsic volcanic rocks, but are much less common in deposits with quartz-free felsic volcanic rocks. The host sequences of epizonal felsic intrusions which are quartzfree are more commonly sedimentary than those of quartz-bearing epizonal felsic intrusions.Quartz, carbonate minerals, arsenopyrite, scheelite, tourmaline and Cr-muscovite ('juchsite') are the most common mineralogical associates of gold. Arsenopyrite is essentially restricted to the volcanic environment, occurring in about twothirds of the deposits with quartz-bearing felsic volcanic rocks and less than half of the deposits with quartz-free volcanic rocks. Tourmaline, on the other hand, is almost ubiquitous in deposits associated with epizonal intrusions and also occurs in about two-thirds of the deposits associated with quartz-bearing felsic volcanic rocks, but in only one of the eight deposits associated with quartz-free felsic volcanic rocks. Scheelite is essentially restricted to ores of quartz-rich fel"

Jan 1, 1982

By Willy Ank de Morais

Para se determinar as propriedades mecânicas de uma junta soldada torna-se necessário conhecer as propriedades mecânicas do metal de adição decorrente de um processo de soldagem. O objetivo desse trabalho foi verificar as propriedades mecânicas de uma solda MAG elaborando e qualificando um procedimento de soldagem. Para isso foi utilizado quatro ensaios mecânicos: tração, macrográfia, micrografia e dureza. Foi estipulado o limite de escoamento, de ruptura, o alongamento e a estricção; macrográfico, determinou-se, a olho nu, a zona fundida, a zona de ligação, a zona termicamente afetada e o metal de base; micrográfico, tração, definiu-se os componentes microestruturais da solda e do metal de base; dureza e foi estabelecida a tenacidade da solda e do metal de base.

Aug 16, 2017

By K Palmer

Alluvial platinum was recovered during gold mining operations in Maud Creek, a tributary of the Howard River. Average electron probe analyses give Pt 88.75, Fe 5.27, Ir 0.70, Os 1.06, Pd 0.34, Ru 0.14, Rh 1.29, Cu 1.06. Rare grains of a Pt-Fe-Cu alloy are also present and an unusual feature of all grains is the relatively high rhodium content which finds expression in segregations of rhodium arsenide, cherepanovite. Platinum is found in the Orepuki area of Southland, where it is probably partly derived from the mafic rocks of the Longwood Complex. Rocks of the Rotoroa Complex, similar to those of the Longwood Complex, form bedrock in Maud Creek and are possibly the source of the Howard platinum. Alternatively, it might be derived by glacial transport from the Matakitaki ultramafic block 30 km to the southwest. Origin from the Rotoroa rocks is preferred as, if the Matakitaki rocks are part of the Dun Mountain Ophiolites, they might be expected to contain osmiridium rather than platinum. The ratio Pt:Ir-Os has been widely used to distinguish low Pt:Ir-Os ophiolitic from high Pt:Ir-Os gabbroic assemblages. Mafic complexes such as Longwoods, Darran, Rotoroa, and Riwaka might be expected to show similar high Pt:Ir-Os ratios and be targets for platinum exploration. Detrital platinum examined from the Parapara area, Golden Bay is mainly osmiridium, with rare grains of rutheniridosmine, very similar in composition to that found in concentrates from the Kaniere dredge, West Coast.

Jan 1, 1987

By Craig C. Johnson

The purpose of this effort was to investigate the feasibility of employing a piezoelectric transducer for seismic communications applications in mine environments. The transducer, a government furnished device incorporated a high Q, spring-mass resonator to load the air side of the piezoelectric crystal. The resonant frequency was seismic load dependent and fell in the range of 300 to 340 Hz. The effort included a mathematical analysis of the transducer, with corroborative laboratory tests, together with actual communications experiments performed first in an open-formation limestone quarry and finally in an operating iron mine. This work showed that the transducer could be coupled efficiently to hard, competent rock media with power conversion efficiencies of 70 to 80 percent (electrical to mechanical) in typical installations. In the iron mine, when radiating peak power was about 30 W (acoustical) in a gated pulse mode, signals were received at a distance of 760 ft through a massive rhyolite porphyry formation. This represents a 15% radiation efficiency with an input of 200 watts. Despite the high ambient noise level due to operating mine machinery, a signal-to-noise ratio of about 20 dB was achieved using a very narrow band filter to process the received signal, and a data rate of about two pulses/sec was demonstrated.

Jan 1, 1972

By Alexandre da Silva Rocha, Luiz Maurício Barreto de Azevedo, Leonardo Sales Araújo, Rafael Menezes Nunes, Matheus Campolina Mendes, Thiago Marque Ivaniski, Luiz Henrique de Almeida

Superliga 718 é uma liga de níquel endurecida majoritariamente por precipitação controlada. As suas principais aplicações são nas indústrias aeroespacial, óleo e gás e nuclear devido a capacidade da manutenção das suas propriedades desde a temperaturas criogênicas até aproximadamente 650°C. Para atenuar fenômenos deletérios de natureza intergranular, neste material são feitos tratamentos termomecânicos específicos para se se aumentar a fração dos contornos do tipo Σ3n.Portanto, o objetivo deste trabalho é analisar duas rotas termomecânicas capazes de aumentar a fração destes contornos por ciclos iterativos de deformação por trefilação, seguido de solubilização em temperaturas sub-solvus  e super-solvus  e envelhecimento além de avaliar a influência da trefilação na precipitação de  mesotextura e tamanho de grão  Para a análise microestrutural, foram feitas imagens de microscopia eletrônica de varredura(MEV) e difração de elétrons retroespalhados (EBSD). Foi feita simulação computacional por elementos finitos do processamento termomecânico para avaliar a distribuição e o grau da deformação no processo. Os resultados mostram que é possível atingir uma elevada fração de contornos do tipo Σ3n pelo processo de trefilação, contudo, a heterogeneidade da deformação ao longo da seção radial influencia em parâmetros microestuturais .

Oct 10, 2019

By Y. C. Lo

Grinding process optimization is an exciting new tool for maximizing the performance of existing mineral processing plants. This paper discusses the methodology of optimization which involves plant sampling, pilot tests, modeling, computer simulation and plant verification. The methodology developed emphasizes the interactions among operating variables and design options. Two example applications demonstrate that AG and SAG optimization provides the basis to increase grinding throughput up to 10 percent. This sys- tem optimization technology has been proven to be very cost effective for grinding plant performance improvement.

Jan 1, 1998