Search Documents

By G. K. Rogers

The portal, which is the near-horizontal, surface point of entry to an underground excavation, can often be an exceedingly difficult area in terms of ground control. Surface and subsurface failures at portals, as discerned during a study involving over 300 case histories, are unfortunately, common. To aid in the engineering evaluation of portals, the Geomechanics Classification System was appended with discontinuity orientation assessment values and support/excavation guidelines. Also, a design model utilizing RMR predicted rock loads in conjunction with half-dome theory is proposed for the most common type of portal failure. Other pertinent comments and recommendations relating to portal stability are included.

Jan 1, 1989

By D. E. Larson

The U.S. Bureau of Mines investigated Fe-base alloys containing 8 pet Crwith Ni, AI, and Si additions as substitutes for standard AISI Type 304 stainless steel (SS) in high-temperature oxidizing applications. The objective of this study was to reduce the amount of Cr required to make an austenitic stainless steel while retaining satisfactory workability, mechanical properties, and oxidation resistance. Alloys prepared in this investigation had a composition of Fe-8Cr-lMn-0.07C with varying amounts of Ni, AI, and Si. A minimum of 10 pet Ni was required to achieve an austenitic composition. The microstructures of the austenitic alloys were very susceptible to room-temperature, deformation-induced martensitic transformations. When the alloys were cold worked or stressed, the materials had far greater tensile strengths than Type 304 SS at room temperature. At higher temperatures, tensile strengths and workability of several of the alloys were comparable to that of Type 304 SS. Although martensitic transformation caused the room-temperature properties of the experimental alloys to be quite different than those of Type 304 SS, the superior oxidation resistance and similar hot workability of several alloys encourage their use as replacements for Type 304 SS.

Jan 1, 1989

By Thiago Vieira Lopes

O mercado siderúrgico atual encontra-se cada vez mais competitivo e exige das empresas esforços na diminuição do custo de produção para que seus produtos mantenham atratividade no cenário global. A incorporação crescente de produtos siderúrgicos oriundos da Ásia no mercado ocidental obriga as indústrias encontrarem alternativas de diminuição de custo de produção, as rotas para que tal objetivo seja alcançado geralmente estão ligadas ao aumento do rendimento metálico e diminuição no tempo de processamento dos produtos. O equipamento gargalo na linha de laminação a quente da CSN, é a cadeira reversível da laminação de desbaste, R2, e pequenas reduções de tempo no processamento de placas são responsáveis por incrementos elevados na produtividade da laminação. Visando ampliar a competitividade da CSN no cenário siderúrgico foi criada uma função, chamada RM-NECK, no modelo matemático do laminador que classifica todos os materiais gargalo desbaste por grau, espessura, largura, número de fornos de reaquecimento e comprimento de placa, permitindo assim, a diminuição no tempo de processamento na zona do VE2/R2. O estudo evoluiu para um verdadeiro trabalho em equipe, envolvendo especialistas da manutenção e operação e, consolidando anos de experiência no desenvolvimento de um algorítmo inteligente o suficiente para reduzir o tempo de processo observando os princípios da teoria das restrições.

Aug 17, 2017

By Martin Nevens

"In 1998, the Iron Ore Company of Canada initiated an aggressive program to improve the performance of its Carol Lake Concentrator located in Labrador City, Newfoundland. This program was termed the Concentrator Upgrade Program. The Concentrator Upgrade Program was a group of initiatives developed with the common goal of improving the overall process and operations of the IOCC Carol Lake Concentrator. The main goal of the program was to increase the annual production capacity of the concentrator from 18.0 million tomes to 21.6 million tomes. This gain in capacity was to be done mainly through improvements in process iron recovery. The target iron recovery value was 80+% versus a historical value of 70%. This improvement in iron recovery would translate to a natural weight recovery improvement from 44% to 50%.The Concentrator Upgrade Program provided the first opportunity in 30 years to make fimdamental changes to the concentrator flowsheet. To accomplish this, several pilot plants were built to evaluate new circuits. AAer 2 years, a new flowsheet was selected for the primary gravity separation circuit and the magnetite circuit. The centrepiece of the new flowsheet was the introduction of Hindered Settling Separators to the metallurgical process.The Concentrator Upgrade Program has since proceeded into detailed engineering and, as of February 2001, construction. The first one of IOCC’s 3 primary AG Mills (Mill 11) has been converted to the new flowsheet at the time of writing and is in the throes of commissioning. This paper will review the flowsheet development program in the pilot plant for the gravity separation circuit and examine the overall benefits to the operation of the IOCC Carol Lake Concentrator."

Jan 1, 2002

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

By Ismael Vemdrame Flores

No panorama atual da coqueificação há uma necessidade comum de aumentar o uso de carvão de menor qualidade, principalmente devido ao alto custo e decrescente disponibilidade de carvões coqueificáveis de primeira linha. Neste cenário, uma forma de melhorar a qualidade do coque é através do controle de tamanho de partículas de carvões e misturas. A granulometria dos carvões pode alterar sua petrografia e propriedades reológicas, podendo ser utilizada de forma benéfica. O presente trabalho é uma primeira parte de um estudo de longo prazo e tem como objetivo avaliar os efeitos de preparação de carvão em suas propriedades. Para esse fim, dois carvões coqueificáveis e uma mistura foram selecionadas e caracterizadas em diferentes faixas de tamanho de partícula. Os carvões e suas frações granulométricas foram caracterizadas por análise imediata, petrografia, fluidez Gieseler e índice de inchamento livre. Os resultados demonstraram que as frações granulométricas dos carvões apresentam diferentes propriedades (cinzas, matéria volátil, composição maceral, fluidez e FSI) de acordo com o tamanho de partícula estudado. Além disso, discutiu-se o motivo por trás das diferenças observadas.

Aug 1, 2018

By Vitor Tomaz de Aquino, Moysés Dutra da Silva, Weslley Luiz da Silva Assis, Rafael Masulck Santos, Tiago Araújo Neves

Neste trabalho é abordado o problema das múltiplas mochilas para modelar a necessidade industrial metalúrgica de alocação de bobinas de aço em um forno de recozimento em caixa. Condições especiais de processo, exigem priorização das bobinas mais antigas do estoque para garantir requisitos de qualidade. Além do mais, algumas limitações físicas e exigências de qualidade devem ser respeitadas, tais como, a obrigatoriedade de agrupamento de bobinas de mesma qualidade e limites físicos de altura e peso. Assim, uma formulação matemática é proposta para resolver este problema, cuja função objetivo visa maximizar o peso total da carga ocupada pelas bobinas de mesmas características e priorizar as bobinas mais antigas em estoque. Os resultados computacionais mostram que a aplicação da técnica do modelo de programação linear otimiza a formação de cargas gerando resultados reais de processo.

Oct 1, 2019

By Tiany Guedes Cota

A indústria cerâmica utiliza as argilas como matéria-prima para fabricação de cerâmica vermelha, branca, de material refratário, entre outros. Possuem um vasto campo de aplicação devido às suas características que, em geral, são decorrentes de sua composição química e do processo de fabricação que lhe originou, tais como: temperatura de queima, proporção dos componentes e granulometria da matéria-prima utilizadas. Comumente vem sendo realizada a substituição de parte da massa argilosa por resíduos industriais, para aproveitamento de materiais, diminuição de custos e impacto ambiental. Nesse presente trabalho, foi realizado um planejamento fatorial em dois níveis das variáveis de adição de pó, temperatura de queima e pressão de compactação nas propriedades de densidade, retração linear de secagem (RLS) e de queima (RLQ). A coloração final também foi um parâmetro analisado. A temperatura parece ser a variável que mais influenciou nos resultados de densidade e RLQ. A pressão de compactação dos corpos de prova não foi uma variável significativa na densidade, RLS e RLQ. Logo, a condição ótima para fabricação dos corpos cerâmicos foi com incorporação de 10% de pó de despoeiramento em substituição ao solo argiloso e temperatura de queima de 1000°C.

Aug 17, 2017

By Cyril Stanley Smith

ARCHEOLOGISTS, by use of the terms Bronze Age and Iron Age, indicate that metals have in the past determined the character of civilization. The relatively simple discovery by a primitive metallurgist that the addition of tin to copper both facilitated the production of castings and increased the durability of the product enabled hunter, warrior, and housewife alike to do things never dreamed of before. Similarly, the smelting of iron and the discovery of hardening methods greatly changed the arts of peace and war. Discoveries of low-melting-point alloys for joining and for making household utensils, and perhaps the adornment of a feminine form by sparkling precious-metal jewelry, have at times changed the destiny of a country. Bronze cannon, the cast and wrought iron Watt engine, copper transmission lines, and aluminum alloy aircraft, are cases of particular metals making possible the realization of an improved engineering design. Perhaps of the greatest influence of all upon civilization was the development of type metal. The rapid increase in the rate of dissemination of knowledge dates from the day that the technique of the pewterer was utilized in making rapidly reproducible and accurately sized letters for printing. It was not movable type, but metal type that was important, for metal castings could be made of identically the same shape and size at an enormous rate, and possessed excellent inking and wearing characteristics.

Jan 1, 1946

By Jeff Whyatt

Deformation of underground salt, trona and potash mines is generally time dependent, providing for gradual adjustment of strata to mining induced stresses. Time dependence can allow for higher extraction ratios provided eventual failure can be tolerated. However, this eventual failure can be violent if creep deformation can shift stress and potential energy to strong, brittle geologic units. The mine failure case studies reviewed here illustrate this process. Yield pillars and defects in bridging strata figure prominently in these cases. Yield pillars provide local and temporary support to the roof, temporarily delaying the cave; and allowing extraction ratios and overburden spans to increase beyond the long term capacity of overlying strata. Defects (faults, voids, thinning) of strong overburden strata reduce the critical span, sometimes to less than panel width. Analyses of many of these cases have focused on a cascading pillar failure mechanism, but recent work and this review point to failure of strong overburden strata as the essential element. The suddenness of failure and attendant seismic events pose hazards to miners and, in some cases, to those on the surface. Characterizing these failures is a first step towards recognizing and managing the risk of catastrophic collapse in underground mines.

Jan 1, 2008

By Lucas Teixeira Costa

A crescente demanda por aços ultrabaixo enxofre em usinas integradas a carvão mineral tem levado a esforços para reduzir o teor de enxofre no gusa e no aço. Todavia, a falta de uma visão integrada dos processos acarreta em otimizações isolados que nem sempre contribuem para uma efetiva redução de custos e aumento de produtividade final. No presente trabalho, foi construído e validado um balanço de massa capaz de realizar uma previsão do teor de enxofre de final de sopro a partir das entradas iniciais de enxofre na carga metálica e nas adições de fundentes. Para isso, considera-se que ocorre transferência de enxofre entre as fases, segundo seus teores e o coeficiente de partição de enxofre. A raspagem de escória de tratamento de gusa deve ser feita com muito cuidado para promover a melhor remoção da camada sobrenadante e ao mesmo tempo evitar perdas no rendimento metálico no processamento do aço. Utiliza-se o teor de enxofre do gusa carregado no LD como o principal parâmetro de controle, e recomenda-se que seu teor seja superior a 20ppm, uma vez que o esforço necessário para reduzir para teores abaixo desse limite será totalmente perdido no LD, devido à reversão durante o sopro.

Aug 17, 2017

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By Jadson Barbosa

Corpos de prova de ferro com diferentes níveis de pureza – um de pureza ultraelevada, dois de pureza elevada e um puro comercial – foram testados mecanicamente com diferentes taxas de deformação no âmbito de um antigo projeto. O objetivo era obter a resistência à tração de cada material e verificar a influência das impurezas e da taxa de deformação nas propriedades mecânicas do ferro de pureza ultraelevada. Para melhor compreender os resultados desses ensaios de tração, uma caracterização microscópica detalhada dessas amostras é realizada através deste trabalho. Para tal, foram analisadas as superfícies lateral e de fratura dos corpos de prova de tração no estereomicroscópio e no Microscópio Eletrônico de Varredura (MEV). O dano foi analisado em seções longitudinais ao longo do eixo de tração utilizando o microscópio óptico; a estrutura dos grãos deformados foi investigada por meio da técnica de microscopia EBSD (Difração de elétrons retroespalhados). Microestrutura, padrão de deformação, orientação dos grãos e as características das superfícies lateral e de fratura são então comparadas quanto ao processo de fabricação, nível de pureza e taxa de deformação.

Aug 17, 2017

By LUIS ALBERTO TORRES-CRUZ

The assessment of liquefaction vulnerability is crucial to understanding the potential consequences of a tailings dam failure. The “Plewes method” is a relatively well-known and simple screening method to assess liquefaction potential based on results of cone penetration testing (CPT) which may be complemented with laboratory testing. The objective of the current work is to emphasise the screening nature of the method and its uncertainties when applied in tailings deposits. Specifically, the paper highlights the difficulties in assessing the intrinsic uncertainty of the method and the additional uncertainty that results from variations of the slope of the critical state line (λ10) along the depth of the CPT sounding. The results of the method are too uncertain for detailed characterisation of tailings even when a relatively low intrinsic uncertainty is assumed. However, the method characterises weaker soils with lower uncertainty (although still too high for detailed characterisation) than stronger soils. The uncertainty of the method is negatively affected by the relatively low λ10 values that are typical of nonplastic tailings. It is suggested that the results of the method should be presented in scatter plots in which the spread of the data is consistent with the uncertainty of the method.

Jan 28, 2021

By Mariana Cristina de Oliveira

O objetivo desse trabalho foi avaliar a influência da deformação plástica na resistência à corrosão do aço API 5L X65, amplamente utilizado na fabricação de dutos destinados à indústria de petróleo e gás natural. Com esse propósito foi realizada análise metalográfica antes e após ensaios eletroquímicos de corrosão. Conclui-se que todas as condições 0%, 0,5%, 1,0%, 1,5%, 2,0% e 2,5% de deformação sofreram corrosão generalizada e as velocidades de corrosão foram similares em solução NACE 177-A.

Oct 30, 2017

By Afshin Sadri

Uma das principais razões para o reparo de altos-fornos é a perda do revestimento refratário, principalmente nas regiões da soleira e onde são feitos os furos de corrida. A operação intensa dos altos-fornos pode resultar em desgaste e deteorização extensiva do material refratário. Isto pode, então, afetar a continuidade das operações e a vida útil do forno. Novo-Lipetsk (NLMK) e a Hatch desenvolveram uma abordagem sistemática para monitorar a condição do revestimento da soleira dos altos-fornos usando Acousto Ultrasonic-Eco (AU-E), um sistema de ensaios não-destrutivos desenvolvido pela Hatch. Inspeções contínuas e periódicas dos altos-fornos revelaram áreas com deterioração acelerada do material refratário, formação extensa de “elefant foot” e acelerado desgaste do refratário, assim como fissuras e outras anomalias. Para prolongar a vida do forno, mantendo a intensidade de suas operações, algumas modificações, tais como a melhoria da qualidade do coque e da limpeza das placas de resfriamento e adição de óxido de titânio, entre outras medidas, foram recomendadas e aplicadas. Este trabalho demonstra como esforços coordenados entre a NLMK e a Hatch resultaram no prolongamento da vida útil de um alto-forno

Aug 17, 2017

By Robert M. Doerr

The research objective was to determine the effect of aluminum alloy additions on the oxidation behavior of cobalt-nickel alloys. Thirty high-purity alloys were reacted with 02 at 0.5 atm at 1,351°, 1,389°, and 1,429° K in a volumetric apparatus for about 300 min. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with aluminum additions of about 0, 1, 2, 4, and 8 wt pet. Large early deviations from, or changes in, the parabolic rate constant were encountered, but in most cases, the reaction rate declined approximately in accordance with the parabolic rate law. A sharp peak in the parabolic oxidation rate constant was observed for specimens containing a to 22 percent nickel and 1 to 2 percent aluminum at 1,351° K, and the rate constants for these compositions were lower at the higher temperatures. Specimens containing 8 percent aluminum reacted far more slowly than did any of the others.

Jan 1, 1971

By M. A. Schellhardt

In recent years development of instruments and equipment for determining subsurface pressures and temperatures in. gas and oil wells has made it feasible to obtain information that eras not available in the past on many gas-production problems. The material presented in this report illustrates particularly the value of subsurface-temperature data in the study of subsurface leakage from gas wells. An abnormal decline in the shut-in pressure of the Lone Star Gasoline Co. A. Jones No. 1 gas well in the southern part of the Buffalo (Tex.) field was observed during an interval when a negligible volume of gas bras being withdrawn from the reservoir. Wellhead-pressure readings indicated that the shut-in pressure of the well declined from 2,295 pounds per square inch gage on February 3, 1937, to 1,445 on February 12, 1935. Tests conducted by engineers of the Lone Star Gas Co. suggested that the subnormal pressure gaged on February 12, 1938, probably was not caused by a head of liquid in the well.

Jan 1, 1940

By Herman O. Ankenbruck

Analyses of statistical data indicate that haulage accidents are one of the largest sources of injuries and fatalities in underground coal mines, and that the rate of accidents in transportation has been increasing during the past few years. These previous analyses were performed by correlating accident or fatality data at a rather high level of miner activity. In this present investigation, underground surveys were made by observing conditions and activities in some detail at a rather low level of activity in an attempt to understand factors contributing to hazards in the specific situations observed. The aim of the current study was to derive preventive measures that might obviate the hazardous conditions and unsafe acts observed; and, following this, to provide recommendations for additional research and development to reduce accident potential in underground transportation. The major project tasks are diagrammed together with the task outputs in figure 1-1. Initially, a preliminary study of ell underground haulage operations was performed in order to establish the kinds of data needed and to provide the rationale leading to the data requirement. At the same time, the various types of haulage equipment used for each operation were defined. A preliminary analysis of each type of haulage operation was performed in order to establish the sequence of tasks required to operate haulage equipment. These tasks were transferred directly onto observation forms, and were used in developing interview forms. In parallel with the task analysis, a review was made of accidents and hazards that might occur during each type of operation.

Jan 1, 1975

By Joseph M. Kurtak

The Bureau of Mines is currently conducting a four year mineral assessment of the 5.7 million acre Valdez Creek Mining District in Southcentral Alaska, as part of its ongoing statewide mining district evaluation program. This report is a summary of the 1987 field work, which included the examination of mines, prospects, and mineral occurrences in the study area. Placer gold has been the most important metal produced in the area, and production totaled 161,131 oz, with the majority of the production coming from the Valdez Creek Mine. Lode gold and silver production totaled 1,581 oz and 8,617 oz, respectively and came mainly from the Golden Zone Mine. Varying amounts of other metals, including copper, lead, zinc, molybdenum, antimony, chrome, nickel, cobalt, tin, tungsten and platinum exist in the study area. Occurrences of industrial limestone and coal are also located in the area.

Jan 1, 2011