Search Documents

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By Donald W. Baggs

This report describes economic mining feasibility studies conducted by the Bureau of Mines to estimate mining costs in the Porcupine mining area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of three mineral deposit types: 1) massive sulfide deposits containing zinc, copper, and silver, 2) vein gold, and 3)disseminated gold. Cost estimates were developed using the Bureau of mines Cost Estimating S,-stem. Discounted cash flow rates of return were calculated using the Bureau of Mines MINSIM (mining simulation) computer program. Three sets of metal prices were used in the study based on recent historical price information. Underground longhole stope mining of a massive sulfide deposit containing 25 pct zinc. 1 pct copper, and 63.6 g/mt silver was found to be economic at high metal prices at a quantity of 13,200,000 mt ore. Cut-and-fill mining of a 26,400,000 mt massive sulfide deposit was found to be economic at medium metal prices. Open pit mining of a similar deposit was found to he economic at medium metal prices and 26,400,000 mt ore, or at high metal prices and 6,600,000 mt ore. Underground mining of a vein gold deposit was found to be economic at a grade of 17.1 g/mt medium metal prices and 1,320,000 mt ore. Open pit mining of a disseminated gold deposit was found to be economic at a grade of 1.71 g/mt medium metal prices and a quantity of 39,600,000 mt ore.

Jan 1, 1986

By Braden T. Lusk, Rex A. Meyr, Kyle A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by MSHA and required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. A polycarbonate safe haven wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed in both half-scale and small scales in the University of Kentucky Explosives Research Team’s (UKERT) explosives driven shock tube. The constructed polycarbonate walls were tested multiple times to determine the walls resistance to blast pressure. The results for each test were analyzed and averaged to create one pressure versus time waveform which was then imported into the finite element program and modeled to compare deflections of each part to that was measured during testing for model validation. This paper summarizes the results.

Jan 1, 2014

By D. Randolph Berry

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller, Inc. to develop guidelines for the storage and use of Self-Contained Self-Rescuers (SCSRs) in underground non-coal mines. An SCSR is a device capable of supplying, in an emergency, one hour of self-contained oxygen (no breathing of mine air). The information and recommendations in this report were developed primarily from three sources: discussions with mine representatives (including management, labor, and government), site visits in underground mines I and a detailed analysis of every reported non-coal accident which produced d hazardous atmosphere during the 5-year period 1976-1980 -plus ten other major incidents from prior years. Volume IV has three major sections: Recommendations and Discussion (Section 2), Analysis of Mine Accidents (Appendix A), and a Summary of Discussions with Mine Representatives (Appendix B).

Jan 1, 1983

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

By Louis H. Meece

The romance of the River lives on in the tales of Mark Twain; and many Americans still think of the Mississippi River in terms of the steamboats loaded with passengers, gamblers and cotton. Yet for many years, coal has been a major cargo on the American waterways. Currently, about 100 million tons a year of coal is handled in some part of its journey from mine to destination by barge. The bulk of this traffic has been on the Ohio River System and the Upper Mississippi River System in years past. Now we have a new entry. Over the past 10 years various movements of coal have developed down the Mississippi River to power plants at Memphis and along the Gulf Coast, and a small amount of metallurgical coal has moved down the Mississippi River for export to Japan since 1970. But in 1980 a brand new player came on the scene. 1980 was a momentous year for the American coal business. Historically, we have exported about 50 million tons a year of metallurgical coal to the world's steel mills. Just before and after World War I, we also had a fairly healthy export trade in steam coal; and again in the late forties, we supplied large amounts of coal to Europe until domestic production could recover from the ravages of World War II. But since the early fifties, the name of the export game has been metallurgical coal. Starting in the mid seventies, something began that was almost totally missed by the American coal industry; and that was the growth in the use of coal first in Europe and now in the Far East as a steam product and as an alternative to petroleum products. As these world coal markets began increasing, the U.S. at first was thought to be noncompetitive because ocean rates were still very low. For example, as recently as 1977, Australian coal could be moved all the way from Australia to the Gulf Coast for $12.50 per metric ton. Coal exporting countries were Poland, Australia and South Africa, except for the continuing exports of U.S. high quality metallurgical coal. But then came the second oil shock, and all of the sudden that $12.50 rate from Australia to the U.S. Gulf became $25.00. And then suddenly and almost unrecognized by the American industry, American coal was in fact competitive at overseas destinations because of the drastic change in trade patterns brought on by the doubling and tripling and quadrupling of bunker fuel prices for ships.

Jan 1, 1982

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

IN 1906, soon after his arrival in New Zealand, a brief article was prepared by the writer on "The Salient Features of the Economic Geology of New Zealand," for the Journal of Economic Geology. In November, 1907, a somewhat similar paper, entitled "The Mineral Wealth of New Zealand," was read at the Royal Colonial Institute in London. The present contribution to the Transactions...

Jan 1, 1909

This publication summarizes the in-house and contract research and development projects programed for fiscal year 1981 by the Bureau of Mines under its Minerals Environmental Technology activity. The document provides a mechanism for interested parties, including potential contractors, to gain insight into ongoing and projected work of the Bureau?s environmental research efforts. Research to identify and correct environmental problems associated with mining and metallurgical operations has long been an integral part of the Bureau's mission. The environmental research and demonstration activities of the Bureau were consolidate in 1979 with the formation of the Minerals Environmental Technology program, which is directed toward the elimination or reduction of environmental problems associated with the extraction and processing of minerals. Among the efforts underway are development of data and technology for assessing the potential environmental impact of minerals development, for monitoring minerals extraction operations, and for establishing viable reclamation requirements on abandoned mine lands; development and demonstration of technology 'or control of environmental disturbances during minerals extraction operations; development and demonstration of land reclamation and mine closure techniques to restore or enhance the productive use of mined lands; development of engineering techniques that incorporate state-of-the-art mining environmental technology in the design and planning of minerals extraction operations; development and demonstration of new mining systems that greatly reduce or eliminate the adverse environmental impacts of minerals extraction; and providing the technologic base for Federal, State, and local establishment of environmental standards for mining operations. Included in the minerals-processing-related work are projects to clean mineral-processing waters: demonstrate a Bureau process for scrubbing SO from powerplant stack :;as; recover dissolved minerals from process streams; stabilize discarded dusts, slags, and tailings: remove hazardous contaminates from byproduct wastes; reduce generation of waste solids; and improve metallurgical process engineering to eliminate pollution. Approximately $21 million was appropriated for this work in fiscal year 1981.

Jan 1, 1981

By A. H. Lang

Introduction The recent uranium discovery at Theano point, lake Superior, is probably a rediscovery of the first reported Canadian uranium occurrence. A description of material from the original discovery was published in 1847 by J. L. LeConte, and many attempts have been made to relocate the deposit. Such attempts have in the past been unsuccessful because of vagueness in the original description of the locality. Besides being a prospect that seems to merit development work, the Camray discovery is important because it reaffirms the occurrence of pitchblende in the eastern part of the Precambrian shield. Much staking followed the announcement of the discovery, and some additional finds have been reported. Location The Camray discovery is at the shore of Theano point, lake Superior, about seventy miles north of Sault Ste. Marie (see Figure 1). It is in township 29, range XIV, district of Algoma. The showing is two miles from Highway No. 17, and is reached by a rough trail that leaves the highway at mileage 72.9 from Sault Ste. Marie. There are no towns of any size nearer than Sault Ste. Marie.

Jan 1, 1949

By A. T. Haile

Detailed monitoring of the response of the rock mass between rockbolt reinforcement units subjected to a simulated seismic source has been successfully conducted. This work has shown the increase in amplification of the Peak Particle Velocity (PPV) with distance from a rock bolt unit, and, a minimum PPV for rockburst damage for the given site characteristics. This understanding, at this site, will allow the design of a suitable rock bolt spacing to prevent unravelling of the rock mass between the rock bolt units for a given level of seismicity. Or, alternatively, an estimation of the requirement for a suitable fabric support system, for the anticipated level of seismicity, can be made.

Jan 1, 2001

The Mahakipawa gold deposit is located 21 km northwest of Blenheim. It became the site of a small hardrock gold rush in 1889 following nearby alluvial gold discoveries in 1888. The study investigates the geology of the area of hard rock mining in the vicinity between Cullens and Waikakaho Creeks. The Marlborough Schist which hosts the gold depos, it consists of polydeformed greenschist facies quartzofeldspathic psammitic, pelitic and volcanigenic schist.

Jan 1, 1993

By AIME AIME

THE 123d meeting of the Institute was held in New York Feb. 14 to 17, 1921. The total registration was 1199, as compared with 1138 at the New York meeting in 1920. The weather was a strange and welcome contrast to that of last year, when New York was buried under six feet of snow as the result of the fiercest blizzard in its history. This year there was no snow, and the weather was said to be much more like an Arizona winter than New York. A complete program of the Technical Sessions is on p. 9. The discussions of the papers presented will be published in pamphlet form as soon as possible and will be noted in MINING AND METALLURGY in the usual way.

Jan 1, 1921

By Nestor Cezar Heck, Aline Lima da Silva

Na produção de vários tipos de aço o controle da composição, tamanho e distribuição das inclusões não-metálicas é de fundamental importância, não só para a qualidade dos produtos siderúrgicos, como também para a garantia da continuidade do processo de fabricação do aço. O controle da composição das inclusões é uma questão que pode ser adequadamente analisada com o uso da ferramenta ‘termodinâmica computacional’, proporcionando ao aciarista informações vitais para ajustes no processo. Neste estudo, com base em cálculos termodinâmicos, foram construídos diagramas de fases especiais com a utilização do software FactSage e seus bancos de dados. Especialmente as influências do Al e do Ti sobre a composição das inclusões foram analisadas, levando-se em conta o teor de oxigênio total. Duas metodologias (estática e dinâmica) foram usadas para se compreender o importante fenômeno da reoxidação. Os resultados deste trabalho, além de auxiliar engenheiros aciaristas a compreender este tipo de análise, deverão estimular estudantes desta área da engenharia a se engajar na assim chamada ‘termodinâmica computacional’.

Nov 19, 2019

By José Eustáquio da Silva

Este trabalho mostra a versatilidade e praticidade do uso da metodologia denominada “Método e Aparelho para Avaliar as Propriedades de Coqueificação do Carvão”, metodologia esta desenvolvida e patenteada pelo corpo técnico da SunCoke Energy. Esta técnica tem possibilitado o desenvolvimento de novas misturas de carvões totalmente alinhadas com os dois grandes pilares da Siderurgia mundial: misturas e coque com baixo custo e qualidade adequada. A fidelização com todas as particularidades do processo real de coqueificação faz desta metodologia uma poderosa ferramenta para tomada de decisão na definição de novos blends, como também para a caracterização de carvões dos quais ainda não se conhece seu potencial para produzir um coque de boa qualidade. Diferentemente das tecnologias similares existentes, o “Box Test” da SunCoke Energy tem robustez suficiente para ser reutilizado para até quatro enfornamentos e é capaz de produzir massa suficiente de coque para que sejam realizadas todas as análises para uma perfeita caracterização do coque.

Aug 17, 2017

By Letícia Pegoraro Leal

O mercado mundial está se desenvolvendo continuamente em todos os segmentos com a finalidade de melhorar a qualidade e diminuir os custos. O aperfeiçoamento e a criação de novas técnicas de soldagem são responsáveis por conservar as propriedades mecânicas e realizar as soldas com um menor número de defeitos. Este trabalho apresenta o processo de soldagem por fricção com pino consumível, conhecido como FHPP (Friction Hydro Pillar Process) em pino AISI 4340 e chapa AISI 4140. Como toda nova técnica é importante conhecer os parâmetros que serão utilizados no processo. Compreender o efeito da velocidade de rotação, força axial e de forjamento, consumo do pino e taxa de carregamento são necessários para avaliar sua influência na microestrutura da solda. Desta forma, no presente estudo, após a soldagem foram realizadas metalografias, a fim de analisar defeitos macro e microestruturais. Por fim, verificou-se significativa influência dos parâmetros de processo no comportamento metalúrgico da região soldada.

Aug 8, 2018

By Art Cooper

Granulation systems are common in the metals industry. The process of granulating slags, mattes and metals is more than a century old, and a number of different systems have been developed to accomplish this task. These systems have followed an evolutionary path, and may be characterized by common elements in terms of molten material handling, granulation methods and post-granulation processing. This paper will summarize the more common systems used in the metals industry, with particular reference to non-ferrous applications.

Jan 1, 2006

By Joshua Alyson Freitas Ribeiro

Aços com teores eutetóides, tratados termicamente são usualmente utilizados em trilhos metroviários. Para que sejam atingidas as propriedades mecânicas desejadas para as devidas aplicações, o material pode ser submetido a alguns tratamentos térmicos, como, por exemplo, Recozimento Pleno, Normalização e Têmpera. Os tratamentos térmicos são de extrema importância, pois possibilitam uma grande versatilidade na utilização dos aços em geral. Neste estudo, as peças utilizadas são provenientes de um trilho metroviário e foram fornecidas pelo Laboratório de Pesquisa e Tecnologia em Soldagem da Universidade Federal do Ceará. Foram feitas análises metalográficas após diferentes tratamentos térmicos em peças do Aço SAE 1080 Fe-C com o objetivo de verificar os aspectos microestruturais e a sua inflências no comportamento mecânico das amostras e a alteração nas propriedades mecânicas. Pelo fato do material estudado ter uma matriz com composição perlítica de, aproximadamente, 100%, são mostradas as consequências devido à mudança nos espaçamentos interlamelares provocados pela aplicação de diferentes tratamentos e a influência da fase martensita na dureza do material.

Oct 30, 2017

By J. W. Neale

Mintek and BacTech have joined forces to provide the metallurgical industry with bacterial-oxidation processes for the treatment of sulphide ores. The processes are aimed at both refractory gold-bearing and base-metal concentrates. Previously, BacTech had commercially implemented the refractory gold process at the Youanmi Gold Mine in Western Australia. More recently, the process has been incorporated in the Sulphide Treatment Plant at the Beaconsfield Gold Mine in Tasmania, Australia. In addition, Mintek and BacTech have recently signed an agreement with the Laizhou Gold Metallurgy Plant in China?s Shandong Province, which will see the third commercial realization of the technology for refractory gold. Development of the base-metal technology is the subject of several papers in the proceedings of this colloquium. The implementation of the refractory gold technology at Beaconsfield is discussed in detail. Some important aspects that are covered include: ?Test work, and the choice of bacterial culture ?Process design choices, and the advantages of the Mintek-BacTech process ?Inoculum build-up ?Plant commissioning ?Plant performance. Besides the Laizhou project, Mintek and BacTech are currently investigating several other commercial prospects for the technology. These include the use of the technology for a gold-copper deposit, where the production of both gold and copper is envisaged.

Jan 1, 2000