Search Documents

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

This final report summarizes the effort on a very aggressively scheduled and demanding development program undertaken by Westinghouse for the U.S. Bureau of Mines under Contract No. H0101262. The objective of this program was to produce hardware and test it to determine the efficacy of certain concepts of Coal Mine Rescue and Survival as established by the request for proposal and the study performed for the U.S. Bureau of Mines by the National Academy of Engineering (NAE). (These are stated in paragraph 1. 1 for reference.) In carrying out this program, Westinghouse provided specific hardware designs in consonance with the objectives of the concepts outlined in the NAE study final report. Though this contract did not require producing final design hardware ready for introduction to the coal mining community, components of the CMR&SS - as delivered - have some value in disaster situations and are to be kept on standby alert. Additional design and production development is required and should be undertaken on most of the subsystems and components before they can be used in the competitive coal mining community.

Jan 1, 1971

By José Bengoa

Con el advenimiento de la globalización económica, las prioridades de los líderes de los países en desarrollo se redujeron a tres: las de atraer inversión extranjera, uso de tecnología avanzada y conectarse con el mundo de la Internet. Por ello, la minería afronta nuevos desafíos que requiere de creativas y oportunas respuestas en esta nueva realidad. En este sentido, el presente texto señala las nuevas perspectivas operativas en la industria del cobre a través de la adaptación de los sistemas integrados de gestión al sector productivo, así como de la corporación de las tecnologías de información y de la internet.

Jul 31, 2003

By Iván Arana Sevallos

Dado que la mina Catalina Huancca posee rocas malas dentro de sus labores mineras, surge la inestabilidad de las mismas. En ese sentido, el presente texto señala la forma de aplicar la voladura controlada a través del uso de espaciadores inertes para espaciar los cartuchos de explosivo y reducir la presión que ejerce el explosivo en el taladro al momento de la explosión.

Dec 1, 2014

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

By C. C. Harris Discussion by B. K. Loveday

B. K. Loveday (National Institute for Metallurgy, Johannesburg, Republic of South Africa) - The paper and subsequent technical note' describing a method of determining the parameters of the three-parameter size-distribution equation developed in the paper were read with much interest. This equation was also used at National Institute for Metallurgy (NIM) to describe size distributions in grinding tests, because it was necessary to have a single equation to describe the size distribution at any time during a test. A graphical method also was used to determine the three parameters, and the use of this method as an alternative to Professor Harris's latest method is discussed here. The three-parameter model can be expressed as follows: Eq. 1 can be rearranged and transformed to Yield a linear reiationship between Y and X (transformed) log

Jan 1, 1970

By A. Pellegrino, F. Collin, C. Guiducci, R. Charlier

A numerical approach for modeling coupled Hydro-Mechanical fracture behavior in 2D is presented in this paper. This approach accounts for the strong dependence of the flow characteristics on fracture apertures and offers an anisotropic description of the flow propagation in the fracture. An interface finite element and a constitutive model are developed . In order to validate the applicability of the model to general geomechanic problems, 2D simulations were performed. Results show the good application of the mathematical model and the fundamental hydraulic role played by the fractures. In diesem Beitrag wird ein Stoffgesetz vorgeschlagen um hydromechanisches Kluftverhalten numerisch zu Modellieren. Dieser Vorgang nimmt die starke Abhängigkeit der Fliesseigenschaften von der Kluftöffnung mit in Anbetracht. Ein Interfaceelement und ein Stoffgesetz wurden entwickelt. Zum validieren der Anwendbarkeit dieses Modells wurden 2D Simulationen durchgeführt. Ergebnisse haben gezeigt dass das mathematische Model anwendbar ist und dass Klüfte eine fundamentale hydraulische Rolle spielen. Une approche numérique pour la modélisation du comportement couplé hydro-mécanique des fractures en 2D est présentée dans ce papier. Cette approche prend en compte la forte dépendance des caractéristiques du flux de fluide sur les ouvertures des fractures et présente une description anisotrope de la propagation du flux dans la fracture. Un élément fini d'interface et un modèle constitutif sont développés. Dans le but de valider l'applicabilité du modèle à des problèmes généraux de géomécanique, des simulations 2D ont été réalisées. Les résultats montrent la bonne application du modèle mathématique et le rôle hydraulique fondamental joué par les fractures.

Jan 1, 2003

[ ]

Jan 1, 2009

By A. Boniface

The International Tunnel and Underground Space Association (ITA) has a number of working groups (WG) that meet at least once a year. One of these is WG12, ?Use of Shotcrete?, of which the author is a member. The purpose of this paper is to draw attention to a number of topics that were discussed at the WG12 meetings held in April and September 2008; and also to a number of other matters that arose from the presentation of thirty-four papers at the 5th International Symposium on Sprayed Concrete held in Lillehammer, Norway between 21 and 24 April 2008.

Jan 1, 2008

Statistics is essentially a study of variability, the use of some suitable mathematical model representative of such variability, and the application of this inferred pattern of behaviour to practical problems. Probability theory is the mathematical structure devised for providing models for chance happenings. Perhaps the simplest example of a chance happening is the result obtained in tossing a coin. Although the result of a single toss can never be predicted with certainty, there is no reason why in repeated tosses the expectancy of heads and tails should not be equal. In such a case the outcomes of the experiment are said to be equally likely, so that the probability of obtaining heads (or tails) is 1 in 2, that is, 0,5. This simple probability .model refers to a 'mathematical' or 'unbiased' coin. Whether such probabilities are meaningful for actual coins tossed in any particular way is a matter for experience to determine. Probability models have also provided the basis for representing observed variability in cases where the actual under- lying probabilities are only partly known or defy analysis. A typical example of the latter case is the variability observed in the values obtained from gold or other ore samples. The interacting natural forces which gave rise to this variability are obviously very complex and are unlikely ever to be unravelled completely. In spite of this, probability theory and the more recent geostatistical theories have provided us with models which can represent this variability on a reasonable basis. Applied statistics and geostatistics must therefore never be accepted as exact mathematical sciences. Furthermore, a basic and essential concept is that in the type of applications covered in these notes, no model must ever be accepted as necessarily the final and exact answer to the problem; thus, any model must prove and continue to prove its appropriateness in practice, preferably by follow-up comparisons.

Jan 1, 1981

By O. Noirot, H. C. Owens, P. D. Rao, D. E. Walsh, J. R. Mokka

Over a period of seven years (1989-1996) the Mineral Industry Research Laboratory (MIRL) University of Alaska Fairbanks, has investigated the effects of temperature, residence time, and particle size on the degree of low-rank coal (LRC) upgrading for a non-evaporative, hydrothermal drying process, also known as hot water drying (HWD). Three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated, factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10-20 minutes of residence time. Thereafter, the upgrading process slows down and over 100 minutes of additional residence time are required to produce similar percentage increases in coal properties to those achieved in the first 10- 20 minutes. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C range.

Feb 24, 1997

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

By R. Steele

In addition to compliance with government emissions and reporting requirements, mining and mineral processing companies are increasing energy efficiency to reduce costs and become more competitive in the global marketplace. One of the major obstacles to identifying opportunities for increased energy efficiency is the lack of readily available data on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. As well as energy reduction, mining and mineral processing companies often struggle with the prediction of energy use, and are often penalized for under or over forecasting. Once again, it is the lack of timely information that makes this prediction difficult. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify energy reduction opportunities, reduce energy costs, and better predict energy use in a mining and mineral processing operation.

Jan 1, 2011

By N. L. Ayres

Tendon support systems have been successfully used to stabilize excavations. Tendon support systems are routinely designed using the axial load-bearing capacity of tendons, namely the tensile strength. To attain tensile strength the tendon must be loaded along its length, which often does not occur in practice. Tendons should optimally be installed at 90° to the surface of the excavation to achieve maximum penetration depth, yet this is often not physically or practically possible, and installations at angles less than 90° occur. Furthermore, the intersection of geological features within the rock mass frequently results in complex loading situations on tendons. The position and angle at which loading occurs results in different combinations of tensile and shear forces acting on the tendon, which can impact on the support performance of each unit and ultimately the whole system. All factors that influence the support system should be understood and taken into account to ensure a sound support design. Combination loading situations are further investigated and tested to obtain a better understanding of the mechanisms involved and the effects on tendon load-bearing capacity. Tendon support units were tested at different installation angles to establish the tendon performance, mechanical behaviour, and load capacity during these loading situations. The results and outcomes are aimed at providing rock engineers with additional data and improved understanding of how tendons could perform under certain conditions.

Jan 1, 2014

By José Héctor Figueroa Paredes

La industria del procesamiento de minerales tiene problemas respecto a la disponibilidad de agua para sus operaciones -en tanto la escasez del recurso hídrico plantea incorporar en los procesos productivos alternativas de procesamiento orientados a optimizar el consumo de agua. En este sentido, Southern Copper Corporation, considera tecnologías de espesamiento de alta densidad a fin de maximizar la recuperación de agua de los relaves de Cuajone, para asegurar los requerimientos de agua para sus proyectos de expansión. Por ello, el presente trabajo señala la factibilidad de recuperar agua de los relaves Cuajone en la Southern Copper Corporation, a través del método de espesamiento de alta densidad que permita el manejo de pulpa densificada, sin la necesidad de formarse una pasta.

Sep 14, 2009

By Aldo Bendezú

En el Perú, el cobalto @>0.1% de concentración se da principalmente en sistemas hidrotermales, particularmente en yacimientos de tipo IOCG y en vetas altoandinas de Zn-Pb-(Ag)-Ni. El primer tipo se presenta en al menos dos segmentos del cinturón de yacimientos IOCG de la costa, entre Lima e Ica. El segundo ha sido documentado principalmente en la Cordillera Oriental, entre Huánuco y Puno. Se han identificado 29 sistemas de vetas y mantos significativos entre ambos tipos. En las vetas, estos ocupan porciones restringidas de 100-500 m de largo, 50-200 m de alto y 0.2-1.5 m de potencia, sugiriendo masas prospectivas del orden de 0.2-0.5 Mt por cada sistema.

May 10, 2023

By JeffreyS. Vipperman, Daniel R. Babich, EricR. Bauer

In response to the continuing problem of noise induced hearing loss NIHL among mine workers, the National Institute for Occupational Safety and Health NIOSH has conducted numerous noise surveys in coal preparation plants. The research, consisting of worker dose monitoring, task observations, and equipment noise profiling, was completed in eight separate preparation plants. Worker dose monitoring was conducted for three shifts in most cases. Workers experiencing higher than allowable doses were task-observed for one full shift to correlate dose to noise source(s). Finally, noise levels on all floors, and in lunchrooms and control rooms, were characterized. Results indicate that only workers who routinely spend a significant portion of their shift in the plants (away from the control rooms) are susceptible to overexposure from noise. Certain pieces of equipment (screens, centrifuges, sieve bends) are the loudest primary noise sources responsible for the worker noise exposures.

By Eduardo Candido de Almeida Wenceslau

O laminador reversível 4-HI de uma cadeira da CSN-PR, o LRF#1 tem capacidade de projeto de 350kton/ano, suficiente para atender a linha de galvanização contínua, LGC, que produz o Galvalume?, primeira unidade no país até sua partida. Deficiências na produtividade desse laminador passaram a ser fator de atenção, pois acarretava na necessidade de complementação de abastecimento de bobinas full hard, BFH, provenientes de outros laminadores do grupo. O presente trabalho mostra o estudo e plano de ação realizado para incremento da produtividade do laminador, sobretudo por meio da redução do número de passes de laminação e revamp do sistema de refrigeração para atender plenamente a demanda da LGC com baixo custo e possibilitar o fornecimento de BFH a clientes externos.

Jul 30, 2018

By Shimeni Baptista Ribeiro Daer, Patrícia Freitas Rodrigues, Edir Neves Teixeira, Naiara Vieira Le Sénéchal, Andersan dos Santos Paula, Francisco Manuel Braz Fernandes

Este trabalho visou em compreender as características microestruturais de uma liga de NiTi rica em Ni deformada a quente por meio do processo de forjamento rotativo, que foram submetidas ao processo com temperaturas distintas de pré-aquecimento (800 e 950 ºC) sem e com tratamento térmico de recozimento prévio (950 ºC por 2 horas) para homogeneização do lingote. Por meio dos aspectos da evolução microestrutural verificados com auxílio das técnicas de Microscopia Óptica, Microscopia Eletrônica de Varredura e difração de Raios X pôde-se observar que a adoção do recozimento prévio para homogeneização e incremento da temperatura de pré-aquecimento as etapas de forjamento rotativo a quente, conduziu a resultados mais satisfatório ao processamento termomecânico a ser aplicado nesta liga, a fim de seguir para as etapas de deformação a frio.

Nov 14, 2019

Typically, large volumes of data are collected during geotechnical investigations for mining projects but rarely is this done in a comprehensive manner that enables all aspects of the geotechnical environment to be evaluated. A geotechnical core logging process has been developed to record mechanical and structural properties of the rock mass. The method enables data for a wide range of rock properties and geotechnically significant major structures to be collected including rock strength, joint surface condition, fracture frequency and fracture orientation. The logging method is unique in that sufficient data is collected to enable the independent determination of all the major rock mass classification systems including rock mass rating (RMR), (Bieniawski 1976, 1989; Laubscher, 1990) Norwegian Geotechnical Institute (NGI) tunnelling quality index (Q) (Barton, Lien and Lunde, 1974) and geological strength index (GSI) (Hoek, Kaiser and Bawden, 1995). The logging system has been specifically developed to allow better and more precise appreciation of rock mass and structural conditions across the project area thereby optimising the use and application of the available geotechnical data and improving confidence in the outcomes of geotechnical investigations. This paper describes the core logging process with case examples showing how the logged data can be used for underground and open pit mine design.

Nov 25, 2010