Search Documents

By C. B. Piazzarollo

Red Ceramic materials are widely used in Civil Construction in Tropical Countries. However, these materials have high porosity and low mechanical strength. Thus, in order to improve these properties, recycle mineral wastes was incorporated into clay from Campos - RJ, ornamental rock waste, from the gneisses cutting of Cachoeiro - ES, 150 km from Campos. After the addition of up 10% of waste in clay mass, ceramic pieces were produced and subjected to the tests of porosity (P) and flexural strength (FS). The test material contains 53.3% clay and 67% waste slit. The X-ray diffraction identified the presence of kaolinite, quartz and feldspar for the clay and, for the waste, quartz and orthoclase. The results of FS and P showed that the residue influenced, positively, the ceramic piece, with strength gains especially from 920º up to 960°C.

Jan 1, 2015

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

In the process of oxygen blast furnace, the lower coke ratio and the higher coke load make the skeleton coke more important. To understand the dissolution of coke in melting and dropping zone, the influence of FeO content, temperature and reaction time on the dissolution of coke with slag were studied by single-factor experiment. Meanwhile, the three factors and three levels orthogonal were conducted. The dissolution degrees were characterized by the weight loss ratio and diameter variation. The results showed that the weight loss ratio increased and the diameter decreased with the increase of FeO content, temperature and time. The three factors and three levels orthogonal test showed that time was the most significant factor on coke dissolution, FeO content of the second, and finally the temperature. The microstructure of coke after reaction indicated that the dissolution occurred on coke surface.

Jan 1, 2016

By Hojat Naderi

In this research assisted leaching of chalcopyrite using sodium peroxodisulfate was studied. Electrochemical techniques such as Tafel analysis and electrochemical impedance spectroscopy (EIS) were used to investigate the surface reactions of a chalcopyrite electrode in the presence and absence of Na2S2O8. According to the results, addition of sodium peroxodisulfate increases the current exchange of the corrosion process and prevents the formation of a passive layer on the surface of the electrode. EIS tests show the trans-passive dissolution of the passive layer on the chalcopyrite electrode in presence of Na2S2O8. Equivalent electrochemical circuits were modeled for Na2S2O8-free and -containing solutions and the model parameters were compared to determine the effect of S2O8 2− on chalcopyrite dissolution. Copper dissolution from pure chalcopyrite mineral and chalcopyrite concentrate was carried out using 15 g/L sulfuric acid solution with and without Na2S2O8. Simultaneous presence of 10 g/L ferric ion and 40 g/L peroxodisulfate salt results in about 40 and 18% of Cu extraction from chalcopyrite concentrate and pure chalcopyrite mineral, after 96 h, respectively.

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By Hongbo Yang, Tongbo Zhang, Ting Huang, Jingshe Li, Fangfang Song

"Liquid core length is a very important parameter of the process of continuous casting, which directly reflects the cooling status in secondary cooling zone and solidification rate of the slab. In this paper, the billet caster in some steel plant in China was chosen as the prototype of simulating. A numerical simulating model for calculating the liquid core length of continuous casting billet was built by ProCAST software, which was verified reasonable and accurate by pin-shooting technique. Based on the model, the relationships between casting speed, casting temperature and liquid core length of casting billet were found, which was very practically useful for the workers on sit to improve casting billet quality. IntroductionContinuous casting process developed very rapidly because of the high metal yield, energy saving, and low-cost 111• And the quality requirements of continuous casting billet for customers became higher and higher with the fast development of economic121• Internal defect usually is the major quality problem for continuous casting billet[3•61 , which is influenced by the solidification process of casting billet, especially the solidification process of liquid core17•81 • So it is very important to study on the relationship between casting parameters and the liquid core length which means the distance between the crystallizer meniscus and the casting billet solidification end-point. In practical production process, the workers usually control the quality of casting billet according to the liquid core length."

Jan 1, 2013

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014

By Mansoor Barati

The present paper is based on a term project for final year undergraduate students, requiring them to evaluate a process for producing silicon from rice husk. The traditional method for production of silicon involves carbothermal reduction of quartz in electric arc furnaces at temperatures exceeding 2000 °C. The technology consumes a considerable amount of electrical energy as well as fossil fuels, resulting in significant CO2 emissions. A flowsheet for production of silicon metal from rice husk is laid out in this paper. The technology will consist of combustors, which will generate steam using the rice husk biomass, power generator, and electric furnace for reduction of the rice husk. Materials and energy balance calculations presented here indicate that such process can be operated independent of external electricity.

Jan 1, 2014

By Sergio N. Monteiro

Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.

Jan 1, 2009

By Jae-Chun Lee, Jinki Jeong, Manis Kumar Jha, Divika Gupta, Pankaj Kumar Choubey

Rare metal indium (In) is mostly used as electroluminescent material in liquid crystal displays (LCD) monitors. Present paper describes leaching studies for the recovery of In from waste LCD monitors in presence of different other impurities. The leaching studies showed that more than 85% of In was leached out using 20% sulfuric acid at 60oC in mixing time 30 min at fixed pulp density 25 g/L. The solution could be purified using SX/IX and from the pure solution metal/ salt could be produced by evaporation, precipitation, electrolysis, crystallization processes.

Jan 1, 2014

By Yong-ming Chen, Chao-bo Tang, Yun Li, Long-gang Ye, Sheng-hai Yang, Hao-tian Xue

In order to achieve high recovery of Cu and Co during cobalt-bearing copper sulphide ore smelting process, reducing agent (coke) and sulphidizing agent (pyrite) were added into molten smelter slag for reducing-sulphidizing smelting to product Cu-Co matte. Effects of reductive atmosphere, pyrite dosage, smelting temperature and smelting duration on Cu, Co, Fe distribution behaviours were investigated. The results show that the distributions of Cu and Co are mainly enriched in Cu-Co matte, and the distribution ratio, LCu and LCo, improve with increasing of coke amount or pyrite addition, whereas above 6 wt.% coke or 20 wt.% pyrite, Cu and Co tend to transfer from matte to cleaned slag. A properly high temperature(1300) and smelting duration(3h) are beneficial to the enhancement of the distribution ratio of valuable metals, and under the given set of conditions, LCu > LCo generally. However, an undesired high Fe contents in matte limit further increase of LCu and LCo.

Jan 1, 2015

By Preben Ingerslev

Control of the reheating of ingots is based either on surface temperature measurements using optical pyrometers or on furnace set points and reheat time determined empirically. This paper presents a real-time mathematical heat flow model, named BESTT, which calculates the temperature distribution in an ingot cross section when reheated or cooled. The model runs on a 486 PC in less than one minute for a variety of ingot cross sectional shapes such as circular, square and with some considerations octagonal and heavy-cornered square. Initial temperatures can either be uniform or nonuniform while accounting for temperature dependent thermophysical properties. The model was developed and verified using 718 alloy ingots in box type furnaces. When integrated with on-line pyrometric measurements, BESTT can provide for improved feed back in the reheating control loop. The use of BESlT will assist in reducing energy costs, and improving product quality and consistency. EPD Congress 1994 Edited by C. Warren The Minerals, Metals k Materials Sodety, 1993

Jan 1, 1994

By A. McLean, Y. Uchida, M. Iwase, M. Myochin, K. Wiikimoto

"Phase diagrams of FeO-containing ternary systems could be derived from experimental data for the activities of FeO. The systems investigated are CaO-CaF2-FeO, SrO-SrF2-FeO; BaO-BaF2-FeO, CaO-CaCl2-FeO, SrO-SrC12-FeO, BaO-BaC12-FeO, CaO-A12O3-FeO and BaO-SiO2-FeO.IntroductionThe importance of phase diagram cannot be overemphasized. In a book, ""Alloy Phase Equilibria""[l], the author, Professor A Prince, states, ""A metallurgist has been defined as a person who thinks in terms of phase diagram"". Whether one accepts this statement or not, it is self-evident that an ability to interpret phase equilibria is essential to the professional metallurgists.The physical chemistry studies of iron and steelmaking process often require phase diagrams of FeO-containing slags. Iso-thermal section of the phase· diagrams of such systems can be derived from experimental data for chemical potentials of FeO. Due to the recent developments in the area of solid state electrochemistry, rapid determinations of the FeO activities have become possible. The present paper is aimed at documenting the derivation of the phase diagrams of FeO containing slags.Experimental AspectsAn electrochemical method incorporating stabilized zirconia can be used for the measurements of the activities of FeO in various slags and fluxes[2]. For the details of the experimental technique, reference should be made to reference 2"

Jan 1, 2000

By Toshio Kurikami, Koichi Yamazaki

"Toho Zinc Co., Ltd Chigirishima Refinery has the production capacity of electrolytic lead for 95000t/y by sintering- blast furnace electrolytic process. Lead raw materials are lead concentrates, spent batteries and dusts that contain lead from other companies, and these are handled by existing smelting process. There are many circulation materials in the process, because the system has been constructed with improving the recovery rate and protecting the environment. This report describes material balance in each process, distribution of the lead and various components, and it examines present state of the processing. In addition, we report the result that we have tried to improve the work environment.IntroductionThe Chigirishima Refinery of the Toho Zinc Co., Ltd. is located in Chigirishima, an island 4km off the coast of Takehara-city, Hiroshima, Japan. The Chigirishima Refinery began lead smelting operations in 1951.The Chigirishima Refinery adopted the sintering-blast furnace-electrolytic process and has an electrolytic lead production capacity of 95,000 tons/year. The existing smelting process handles raw materials from lead concentrates, spent batteries, and lead-bearing dust from other companies. This system was constructed with the intentions of improving material recovery ratios and protecting the environment; therefore, there are many materials recirculating throughout the smelting process. This report describes the material balance in each process and the distribution ciflead and various components, and it examines the present state of processing. In addition, we report the results of our attempts to improve the work environment."

Jan 1, 2000

By Billy W. Osborne

The use or primary dross as a source for aluminum ion in the manufacture of aluminum sulfate offers opportunities for an inexpensive raw material. The aluminum sulfate industry in the US is a mature market with numerous small plants operating close to major users. The majority of manufacturers use either bauxite or aluminum oxide trihydrate as a source for the alum¬inum ion.. However, using process technology developed and patented by IWC, the oxides are removed from primary dross for use in manufacturing aluminum sulfate prior to metal recovery. This process offers the benefit of reducing costs for metal recovery. This paper discusses some of the methodology used in this process.

Jan 1, 1995

By Yuanbo Zhang, Zhixiong You, Zijian Su, Bingbing Liu, Guanghui Li, Guang Yang, Tao Jiang

Sodium stannate is widely used in the electroplating and tin alloy industry. But the traditional processes for sodium stannate production are characterized by long flowsheet, high production cost and strict requirement for the equipments, etc. In this study, a novel process for sodium stannate preparation from cassiterite concentrate and sodium carbonate via roasting in CO/CO2 mixed gas then followed by leaching was developed. The effects of roasting parameters on the Sn leaching efficiency were conducted. A Sn leaching efficiency of 77.2% was obtained under the optimal conditions. Sodium stannate (Na2SnO3·3H2O) with a purity of 95.8% was produced by the new process, which is better than that specified for the industrial first-grade product.

Jan 1, 2014

By Dirk Verhulst, V. I. Lakshmanan

Why Chloride Hydrometallurgy?The most available, cheapest and best known reagent for treating ores and other raw materials for the metallurgical industry is sulfuric acid. Hydrochloric acid is second in line. What often happens is that a process is developed on the basis of sulfuric acid, and that at some point the question arises: wouldn't hydrochloric acid do this better?Considering hydrochloric acid immediately opens a very interesting field of research. To summarize a few comments from another paper presented at this symposium [1]: chlorides are far more soluble than sulfates (with a few interesting exceptions); the hydrogen ion activity is greater in chloride than in comparable sulfate solutions; higher oxidative conditions are possible; regeneration is more straightforward; more diversity is possible and better conditions for the separation of species can be found for solvent extraction and ion exchange; sulfur in the ore can be separated as elemental S; higher metal concentrations in solution and more flexibility in the chosen oxidation state means significantly lower energy costs.Also, the volatility of many chlorides at higher temperature allows further separation without the need to go to a different system. Chlorides also form molten salts with a low melting point, providing another means of separation and purification in the same chloride medium.

Jan 1, 2011

By Jilai Xue, Jun Zhu, Germain Kouma Ndong, Qiaochu Liu, Luxing Feng

"High-temperature oxidation and corrosion behaviors of Ni-Fe-Cr alloy as inert anodes for aluminum electrolysis have been studied in oxygen and molten electrolyte. The oxidation and corrosion scales on the anodes tested were analyzed using XRD and SEM-EDS. The oxidation rate is found to increase with increasing temperature from 700 °C to 950 °C, which can be approximately described by an inverse power rate function. The oxidation scales at 750 °C, 920 °C and 950 °C contain Cr-rich phase along with FeCr204 and (Feo.6Cro4)203. The corrosion extent of Ni-Fe-Cr anodes in electrolyte is dominated by temperature, which can make the scales thickness double from 700 °C to 750 °C or from 920 °C to 950 °C. Cr and Fe in the scales on the anode in electrolysis corrode preferentially into the molten electrolyte, while the nickel oxides could better sustain the corrosive environment in electrolysis. The results can be useful for developing inert anode material for potential application in aluminum electrolysis.IntroductionThe development of an inert anode for aluminum electrolysis has been a long term goal for aluminum industry. The present process for primary aluminum production involves the reduction of alumina with carbon anodes, forming carbon dioxide:"

Jan 1, 2013

By J. L. Jambor, H. W. Nesbitt

Oxidative dissolution of pyrrhotite and pyrite is largely responsible for the sulfate-rich waters of the vadose zone in the Waite Amulet tailings. Although the shallowest of the sulfate-rich waters are of the Fe-SO4 type, they change to Mg-SO4-type, near-neutral waters within 1-2 m of the tailings surface. Phyllosilicates and amphiboles are the only minerals present in sufficient quantity to ameliorate the amount of acidity produced. X-ray diffraction and microscopic studies of bulk sample indicate that quartz, chlorite, talc, amphiboles, magnetite, albite, and micas are the major and minor non-sulfide minerals, but their variations with depth do not give clear indications of depletion in the vadose zone. Mineralogical and bulk chemical compositions of the tailings confirm that Fe2O 3 has accumulated in large quantity in the vadose zone, with the Fe having been derived from Fe sulfides. When the effect of Fe2O3 is accounted for, the bulk compositions suggest that SiO2 is slightly more abundant in the vadose zone than in the saturated zone. This may be the result of residual enrichment of siliceous minerals such as quartz and albite in the vadose zone. Weathering of the tailings since the cessation of deposition in 1962 has resulted in a well-defined zone of sulfide depletion and secondary sulfate-mineral development. Although some silicate dissolution is indicated by pore-water compositions, the role of silicates in providing neutralization seems to have been minimal. The contribution by silicate minerals in laboratory tests of neutralization potential may be excessive relative to that in natural settings.

Jan 1, 1999

By Martin J. Hansel, Jan Bäckström

Starting from historic perspectives on converting at the Rönnskär Smelter, the continuous developments of refractory practice is described. In the development the joint efforts of operators and suppliers of refractory have lead to significant achievements. This paper comprises the development of the converting process and the refractory lining as well as future prospects regarding operation and refractory lining design, especially in the face of equipment and raw material availability. 81

Jan 1, 2009

By M. Demuth, B. Holleis, M. Potesser, D. Spoljaric

"In 2005, Messer Group established a technology competence centre for metallurgy in Gumpoldskirchen (Austria), with the aim to develop oxygen burners which satisfy today's and upcoming standards of legislation as well as customer requirements. With the assistance of the Development Sponsorship Fund (FFF) of Austria, cooperation with the University of Leoben was agreed on. With the long term experience of the Gas-Warme-Institut ""GWI"" in Essen (Germany) and the University of Leoben, different new burners have been developed.The efficiency of industrial combustion processes can be increased in two ways (which can be seen in Figure 1 ), either by preheating the fuel and combustion air or by adding oxygen. Due to the high 79 % Nz ballast in air combustion, only low flame temperatures can be reached. This results in high heat loss in the exhaust gas, caused by the low combustion efficiency. Oxygen can be introduced into the combustion chamber using different techniques:• Oxygen fuel burners• Direct oxygen injection into the fuel air flame• Underlaying of the fuel air flame• Enrichment of the combustion airIn Figure 2, the theoretical flame temperature for the stoichiometrical combustion of natural gas is plotted as a function of oxygen enrichment. Therefore, it can be concluded that even low enrichment values produce higher flame temperatures and result in higher combustion efficiency."

Jan 1, 2012