Search Documents

By Xuemei Zheng, Aiyuan Ma, Yonggang Zuo, Jinhui Peng, Shiwei Li, Libo Zhang

The effect of moisture content on the dielectric properties and microwave drying behavior of zirconium hydroxide was studied by using an open-ended sensor dielectric measurement system at the frequency of 2.45 GHz. The experimental results showed that moisture content can significantly influence the variation of dielectric properties. Dielectric constant, loss factor and loss tangent all increase with the increasing moisture content. Compared with the conventional drying method, the microwave-assisted drying method resulted in a substantial decrease (81.8%) in the drying time, and the drying effect was better at the lower power level of 600 W. This study offers the useful information on dielectric properties of zirconium hydroxide, which can be used for developing microwave drying applications in mineral processing and designing better microwave sensors for measuring zirconium hydroxide moisture content.

Jan 1, 2015

By Seyed Mahdi Abbasi, Adel Sheikhhosseini

"This research was conducted to study the changes of microstructure, chemical composition and mechanical properties ofIN718 superalloy after adding aluminum to the ESR process slag. The experiments were performed in VIM and ESR furnaces. The results showed adding 1.5 percent aluminum to the slag increase lave phase in the IN718 samples from 0.34 percent in the base sample to 3.0 percent. It also indicated that the more increase of aluminum in slag cause decrease in the aluminum absorb yield in the superalloy.it is observed that increasing aluminum from 0.7 to 1.1 and then to 1.5 percent caused a decrease of absorb from 91.4 to 76.3 and 74.6 percent respectively due to increasing of aluminum oxidation. According to the results, tensile strength increased and ductility declined in the IN718 samples mainly because of rising the amount of y' volume fraction.IntroductionIN718 superalloy is an iron-nickel base superalloy with constant mechanical properties at medium at high temperatures. For the past seven years a considerable amount of time and effort has been expended by both suppliers and users in the study of Alloy 718 [ 1]. The interest in this material stems not only from the interesting metallurgy associated with the alloy, but with the large usage of the material in numerous applications In fact many people believe that the projected use of this alloy increase significantly over the next several years, The large use of Alloy 718 is the result of its performance in respect to high strength, good ductility, good repair weld ability and from its versatility of being supplied in various product forms. This superalloy is used in wide ranges of industries such as aerospace and gas turbines [2]. In the past more than 20 years many researchers did a lot of work to improve the structure stability of IN718 at high temperatures and intended to develop a new 718 type alloy to be used beyond 650 °C. One of the methods is to control and phase precipitation behavior by means of adjustment of Al, Ti and Nb contents. The other idea is to strengthen the matrix by altering the content of solid solution elements such as W and Co. The adjustment of these alloying elements can change phase precipitation behavior [3]. If detailed information dealing with phase precipitation behavior can be obtained before experimental work for alloy development, a lot of time can be saved and the development cost can also be reduced. In recent years, computer modeling based on experimental data plays an increasing role in alloy design and development. Adding Al to the Iron and Nickel increas the strength of superalloy by formation of y phase and subsequence formation of n phase. Ti in IN718 superalloy also helps the formation of MC carbides and gamma prime phase. Increasing Al/Ti and (Al + Ti)/Nb will lead to form finer particles of y'. More uniform distribution of the precipitates and enhancing stability of y' in IN718 superalloy [ 4]. Adding Al to slag of ESR process can reduce the oxide inclusions because of the strong tendency of Al to oxidation. In addition, tensile properties of IN718 superalloy improve. The most significant inclusions in IN718 superalloy are Alz03 and TiN that were found in agglomerate forms. Thermodynamic calculation results indicate that the effect of increasing Al shows a strong increase in solvus while phase solvus shows mildly decrease when Al level is less than 2%, after that it dramatically decreases [ 5]. Laves phase precipitation and the appearance of phase are occurred when Al content reaches 2%. In fact, when Al content is beyond 1.5%, phase has already precipitated in a considerable scale. Shows the fraction of increases greatly while the fraction of phase decreases remarkably with the increment of Al content. Based on thermodynamic theory, if these particles were not existed in the melt during cooling agglomeration would not accrue and the superalloy will be cleaned By adding Aluminum to the slag, the metal reacts with oxyge"

Jan 1, 2013

By Mike Dry

While McCabe-Thiele plots are useful for designing single-component solvent extraction systems, not least because of their simplicity, they are less useful for multi-component solvent extraction. This paper presents a relatively simple method, compared to other approaches, for modelling solvent extraction as chemical equilibrium reactions between the various aqueous and organic species. The essence of this approach is how values for the equilibrium constants can be extracted from standard laboratory data. Synergistic solvent extraction of nickel is used to illustrate the method.

By Adam J. Gesing

The eddy current separator (ECS) is designed to separate nonmagnetic (nonferrous) electrically conducting (metallic) particles from nonconductive residue. Nonferrous metallic particles are repelled out of the material stream passing over the eddy current rotor (ECR). The rotor is housed in a fiberglass composite outer shell that serves as a conveyor head pulley. This results in the desired metaVnonmeta1 separation. The behavior of ferromagnetic particles, mainly iron and iron oxide (i.e. rust), is quite different. These particles are strongly attracted to the magnets and the smaller particles tend to align their long axis in the direction of the magnetic flux. Since the direction of the flux changes with the passage of each magnet pole, the small particles spin at very high rates causing wear of the belt and of the composite outer shell housing the ECR. Large particles, when trapped under the ECS belt, cannot spin, but can be heated by the eddy current effects and subsequently can burn through the composite outer shell. We discuss the practical implication of this behavior of iron and rust on the design, performance and maintenance of eddy current separators.

Jan 1, 1999

By Jian-hua Ren, Guang-liang Wu

A lot of dust is produced in iron and steel enterprises, giving rise to serious environment pollution, with which all countries are trying to find methods to deal. The influence of relevant technological factors on dephosphorization was investigated in laboratory, and the effect laws of that were analyzed. The results demonstrate that, in the given conditions of the best slag-metal proportion for hot metal dephosphorization is 1:10, and the optimum temperature is 1350 , The phosphorus distribution ratio of dephosphorization agent containing converter dust of 30% has the maximal value, with dephosphorization rate reaching 85%. Under the optimal conditions, premelting dephosphorization agent can significantly improve the ability of dephosphorization, dephosphorization efficiency increasing to 92%. Therefore, the dust can substitute the oxidant and fixative of dephosphorization agent, be used in hot metal dephosphorization, to enhance the efficiency of utilization.

Jan 1, 2016

By Gui-fang ZHANG, Zhe SHI, Lei GAO

Secondary V-recycling slag, an industrial waste containing high gallium is being dumped continuously, which causes the loss of gallium. Thus, the alkali fusion process was employed to recover gallium from this slag. The effects factors on extraction of gallium such as roasting temperature, roasting time, alkali fusion agent concentration and CaO concentration were investigated in the paper. The experimental results indicated that excessive roasting temperature and roasting time is unfavorable to the recovery rate of gallium. The appropriate roasting temperature and duration are 1000 and 2 hours, respectively; The appropriate proportioning of Na2CO3: NaOH is 2:1 when the concentration of alkali fusion agent weighs 0.4 times the mass of the slag; In order to remove SiO2 from the leaching liquor, CaO should be used as an additive in the roasting process. The appropriate concentration of CaO should weigh 0.2 times the mass of the slag. Employing these optimal alkali fusion conditions in the roasting process, gallium recovery is above 90%

Jan 1, 2015

By Edward Peters

Scandium (Sc) has unique properties and is one of the more valuable elements in the periodic table. Scandium can be used in solid oxide fuel cells and to produce high strength aluminium alloys of value, for example, in the aerospace industry. Scandium is often grouped together with the rare earth elements (REE). Amongst others, scandium can be found in bauxite residues, so called red mud. It is possible to extract and enrich scandium from red mud by leaching and solvent extraction. Scandium can then be recovered from the pregnant strip liquor by crystallization. The strip liquor will however still contain certain impurity elements. In the present work, a method for obtaining a pure scandium solid phase by direct crystallization from the strip liquor is evaluated. It was found that Fe and Ti co-precipitate with Sc under the conditions employed.

By Heng Yi

The salt lake brines that lithium is extracted from have high chloride levels making the brine very corrosive to stainless steel extraction column internals. This is a significant problem in column scale-up to industrial production. Two types of corrosion-resistant ceramic internals, the hybrid ceramic internal and ceramic plate, were designed and tested under pilot conditions for future industrial application in this field. The hydrodynamic results (Yi et al. Ind Eng Chem Res 56 (4):999–1007 (2016), [1]) show that holdup of hybrid ceramic internal is higher than that of ceramic plate by around 50%, while Sauter mean diameter when using the hybrid ceramic internal is smaller than when using the ceramic plate by around 30%. This results in a larger mass transfer area, hence better mass transfer efficiency for the hybrid ceramic internal. Axial dispersion and mass transfer parameters are also examined (Yi et al. Ind Eng Chem Res 56(11):2049–3058 (2017), [2]). The results show that the column with hybrid ceramic internals has 50% lower axial dispersion coefficient and 50% higher mass transfer coefficient, leading to higher mass transfer efficiency. The transfer unit height of the column using hybrid ceramic internals can be as low as 0.2 m, showing very good efficiency. This is promising for near-future applications. Two-phase computational fluid dynamics (CFD) models have been developed for the two columns with ANSYS FLUENT commercial software. CFD successfully predicts the higher holdup and lower axial dispersion coefficients for the hybrid sieve plate pulsed column as measured in the experiments, and the cause for the difference in performance has been explained with information from CFD.

By Wenbin Liu

A novel route for rapid synthesis of ultrafine WC-Co cemented carbides with homogeneous binder phase distribution is reported. The composite powder is produced by in situ reduction-carbonization reactions by using WO2.9, Co3O4 and carbon black as raw powders. The reaction equilibrium and phase stability are studied by thermodynamic calculations. The WC-Co composite powder is condensed by spark plasma sintering (SPS) to obtain the cemented carbides bulk. The sintering temperature is lower than that in the conventional sintering methods by 1500C, while the sintering time is remarkably reduced by 3-5 times. The high performances of the hardness and the fracture toughness are obtained. The experimental results confirm that the present processing scheme of in situ reduction-carbonization reactions and subsequent SPS sintering is an efficient way to prepare WC-Co cemented carbides, and is apparently superior to the conventional long-period techniques of preparing composite powder and cemented carbides bulk.

Jan 1, 2008

By Liu Wei-feng

In this paper, the practice of separating precious metals from base metals in gold-antimony alloy by selective chlorination leaching under controlling potential in China has been introduced in detail. The precious metals and the base metals can be separated completely when the complex gold-antimony alloy is treated by this process. The impurity metals were removed effectively since the leaching efficiencies of copper, nickel and antimony are over 99%, with direct recovery of gold being 99.83% that is about 20% higher than that of the original process and silver, antimony, copper and nickel are also recovered effectively. The gold grade of the resulting crude gold powder can reach to 94%.The new process has been applied in the treatment of gold-antimony alloy for two years, and many former procedures have been cancelled, such as electrolysis, Anode slime leaching by nitric acid, smelting in crucible and blowing in muffle. The new process is more shorten, lower cost and friendly to the circumstance comparing to the original process.

Jan 1, 2008

By Dany Racine, Daniel Marceau, Denis Laroche, Dmitry Lukovnikov

Carbon base materials play a critical role in the performance of Hall-Héroult cell. The determination of their thermo-physical properties is of primary importance for modeling and designing complete cell systems. However, overcoming the associated experimental hurdles is complex and often underestimated. Of them are the Poisson’s ratio measurements and the continuous oxidation/burning of the materials at temperatures above 200°C. The novel procedure developed in this research is based on the Gleeble® 3800 system. Its vacuum chamber allows test with a chosen atmosphere at temperature of more than 1000°C. Young’s modulus, Poisson’s ratio and the coefficient of thermal expansion values can all be adequately measured using a single test. Cylindrical carbon samples (: 50mm, L: 100mm) were tested in the modified system at temperatures ranging from room to 950°C without any trace of oxidation. The resulting values were also in good agreement with literature data for a specific graphite material.

Jan 1, 2015

By Jiakai Zhang

Many postconsumer electrical and electronic equipment wastes contain a considerable amount of rare earth elements (REEs); however, the current level of REE recycling from them is limited (<1%). Neodymium–iron–boron (NdFeB) magnets, used at both small- and large-scale, from computer hard disk drives and small tools to wind turbines and cars, are a good example of such waste materials that contain high content of neodymium (Nd) and dysprosium (Dy). These elements are considered critical metals because they are the main building block of emerging green technologies that will allow for GHG emission reductions. Because demand for these green products is increasing around the world, the demand for REEs is increasing quickly, putting their supply at risk in the near future. Thus, it is critical to develop efficient, robust, and cost-effective processes to recycle these elements from this class of electronic waste materials. Here, we performed a thorough characterization of a N52–NdFeB magnet to identify its composition, crystal structure, and morphology. Furthermore, we developed an efficient hydrometallurgical process to extract Nd and Dy with high efficiency (more than 95%).

By Zeng Zheng, Liu Chen, Yu Xing-Fu, Tian Su-Gui, Zhang Chao

"Single crystal nickel-base superalloy is prepared by using the various withdrawing rates. By measuring creep properties and microstructure observation, the influence of the element segregation on creep properties of the superalloys is investigated. Results show that the dendrite spacing and the segregation extent of the elements decrease with the enhancing withdrawing rate. The superalloy with smaller dendrite spacing has lower segregation of the elements and better creep resistance. The dislocations climbing over the rafted y’ phase is thought to be the deformation mechanism of the alloy during steady state creep. In the later stage of creep, the fact that some dislocations shear into the rafted y’ phase may twist the rafted y’ phase. As the creep goes on, the initiation and propagation of the cracks occur up to occurring creep fracture, which is thought to be the fracture mechanism of the superalloy during creep.1. IntroductionSingle crystal nickel-based superalloys consist of high volume fraction of ?? strengthening phase and ? matrix, and possess the excellent high-temperature mechanical and creep properties, therefore, they have become the main material to make the blades of the advanced aeroengines[1-3]. Some literatures report that the temperature-bearing and creep-resistance properties of the single crystal nickel-based superalloys can be remarkably improved as the increases content of the refractory elements, such as W and Re[4-6]."

Jan 1, 2012

By Mariana Barcelos, Frederico Muylaert Margem, Giulio Rodrigues Altoé, Pedro Amoy Netto, André Gomes, Sergio Neves Monteiro

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of polyester matrix composites reinforced with continuous fique fibers, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Jan 1, 2015

By Manjie Li, Mingrui Yang, Haijun Peng, Shuxing Qiu, Wei Liu, Shengfu Zhang

It is important to produce and utilize highly reactive coke in order to reduce the energy consumption and CO2 emissions through improving shaft efficiency in blast furnace. The present study aimed to investigate the transformation of iron minerals and properties of iron coke (the coke mixed iron ore fines). Along with the increase of iron ore fines, cold strength displayed a slight downtrend and the pore structure wasn’t inferred to be a major factor affected the properties of iron coke. During carbonization, the majority of mixed iron oxides were reduced to metallic iron by CO and H2 and the degree of metallization achieved to approximately 75%. Nevertheless, produced metallic iron was oxidized by pure CO2 during gasification. Iron coke reactivity index (ICRI) was obviously enhanced and the iron coke strength after reaction (ICSR) drastically decreases, which were also significantly influenced by crystal structure of carbon.

Jan 1, 2015

By M. Giralico

Optimized mixer settler designs will now handle flows of over 25,000 GPM. The size and expense of the equipment hamper experimental settler optimization efforts. Computational Fluid Dynamics (CFD) is a timely and predictable tool for settler design development. In the past, CFD has been used to evaluate only the flow field in pumped and auxiliary tanks. A similar numerical analysis is used to evaluate settler flow and phase separation. Phase separation is analyzed using multiple species for the aqueous and organic phase. Experimental validation shows good agreement between the computational and experimental solutions in both flow field and phase separation. The computational model is used to show performance differences between various choices of settler geometry, liquid depth, with variable flow rates. Understanding the differences allows the development of optimized settler designs. System improvements are predicted to lower entrainment levels further and/or allow new smaller footprint designs. This paper focuses on the major design components of the settler and how future technological advances will lead to further improvements in their design. LIGHTNIN?s new designs will handle tomorrow?s production requirements, while maximizing profits.

Jan 1, 2003

By Glenn Stevens

After 40 years of operation with the original design, Pan Pacific Copper determined it was necessary to rebuild the Saganoseki Flash Smelting Furnace to continue safe operation. The original design employed a rigid steel frame, which, through hearth growth, led to severe distortion of the frame. Contributing to the continued growth of the hearth were thermal cycles that occurred during the government mandated annual shutdowns. Hatch designed a unique sprung bound, pivoting binding frame to maximize crucible size within the existing furnace footprint, while integrating the PPC designed cooling jackets. The bound system maintains tight brick joints, while the new conductive hearth design with integrated bottom cooling produces a protective freeze layer to accommodate higher furnace throughput. Minimization of furnace downtime for the rebuild was achieved through effective construction planning, highly trained contractors, and through an efficient start-up and ramp-up to full production.

By Tetsuya Uda

Our recent achievements of rare earth separation technique[1,2] and new process idea for rare earth magnet recycling[3] are reviewed, (1) Binary chloride mixtures of rare earths were separated by a new selective reduction-vacuum distillation process. According to our experimental results, apparent separation factors were 8.1 for the Pr-Nd chloride mixture and 570 for the Nd-Sm chloride mixture. These values are much higher than conventional solvent extraction methods. (2) A study of recycling process of magnet sludge was carried out. The rare earths in the neodymium magnet sludge were extracted by chlorination with FeCI2, An activated carbon was used as a de-oxidation reagent Metallic iron in the sludge was not chlorinated because the iron monochloride is not stable, The extracted rare earth chlorides were easily separated from Fe-alloy and the excess of FeCh by vacuum distillation, 96 % of neodymium and 94 % of dysprosium in the sludge were extraeted into chloride phase, By the vacuum distillation, a mixture of neodymium and dysprosium trichlorides of 99.2 % purity was recovered, On the other hand, the rare earth chlorides can be converted to the corresponding oxides by a pyrohydrolysis reaction accompanied by a formation of HCl gas, The HCI gas can chlorinate metallic iron to FeCh, Therefore, a new recycling process for rare earth magnet waste can be realized as a chlorine circulation type process. During the process, only carbon and water are consumed and there are no toxic pollutants, Moreover, the obtained rare earth oxide can be directly used as raw material in the conventional oxide electrolysis process,

Jan 1, 2003

By Yun Soon Han, Joo Hyun Park

Indium (In) solubility in the FeO-SiO2-Al2O3-5%CaO slag was measured under p(O2)=10¯¹¹ atm at 1573 K to clarify the dissolution mechanism of In in FeO-bearing metallurgical slag. The In solubility increased with increasing oxygen partial pressure, whereas it decreased by increasing the activity of basic oxide, viz. FeO. Thus, a dissolution mechanism of In in the FeO-SiO2- Al2O3-5%CaO slag was described by the following equation. In(s)+1/4O2(g)=(In+)+1/2(o2-) The enthalpy change of the In dissolution reaction was negative, indicating that the dissolution reaction was an exothermic reaction. This is consistent with the above reaction mechanism.

Jan 1, 2014

By Li Qian

Mechanisms of bio-dephosphorization from iron ore was investigated in this Paper. The results show that there are two bio-dephosphorization ways from iron ore, the one is that Acidithiobacillus ferrooxidans directly derive phosphorus from the ore, the other is phosphorus is able to be leached acid produced during metabolizing of Acidithiobacillus ferrooxidans, and the latter is more important than the other. Adding suitable pyrite can enhance the bio- dephosphorization process through providing nourishment and producing acid directly due to S 3oxidized or indirectly due to Fe3 as oxidant. The potential varies in the range of 0.434~0.498V and pH is in the range of 2.5 ~ 1.25 during bio-leaching process. It can be founded that, according 2+to the E-pH graph of Fe-H2O system, Fe wouldn?t be oxidized under sterile system in this potential and pH ranges. It can be obviously concluded that the Acidithiobacillus ferrooxidans are 2+able to reduce the potential for the oxidization of Fe and make the oxidization occur in the above pH and potential zone, so the bio-leaching process can proceed. the investigation of E-pH graph of P-H2O system show that H3PO4 can exist steadily.

Jan 1, 2009