Search Documents

By Y. A. Chang, J. Woodford, C. R. Kao

Reactive diffusion studies between NbC and Si were carried out at 1300 °C under a vacuum of 10-5 torr and a uniaxial pressure of 1 MPa. The annealing time ranged from 8 to 100 hours. The Si used was single crystal silicon; the NbC was hot-pressed powder compact. A NbSi2+SiC two-phase reaction layer formed with NbSi2 as the matrix and SiC as discontinuous particles. The microstructure of the reaction product is homogeneous, dense, and fine. The NbSi2 grain size and SiC particle size are in the micron range. The growth of the reaction products follows parabolic kinetics. Extrapolation of the data to zero thickness suggests an apparent incubation time of 3.5 hours. However, for short annealing time «60 hours), the thickness data can be approximated by linear kinetics with an initial growth rate of about 2 11m/hr. Based on these experimental observations, a growth mechanism for the reactive diffusion between Si single crystal and NbC powder compact is proposed. We propose that the nucleation sites for the SiC particles are at the voids of the NbC powder compact. This proposed nucleation mechanism offers a potential way of controlling the SiC particle size by changing the void size and void density of the NbC powder compact. This hypothesis, if proven to be true, will allow us to control mechanical properties of the composites by tailoring the SiC particles formed. It is also pointed out that the microstructure requires Si to be the dominant diffusing species and to diffuse through the reaction layer, while Nb and Conly have to undergo local rearrangement.

Jan 1, 1996

By G. Gao

Flyash from municipal solid waste (MSW) incinerators is frequently classified as a characteristic hazardous waste due to its lead and cadmium content. Extensive investigation has therefore been carried out to detoxity the flyash by leaching and to recover lead, cadmium and zinc. Detoxification can be accomplished by leaching in HCI/NaCI solutions. Optimization of leaching conditions for effective detoxification and subsequent metal recovery can be achieved by controlling the acidity of the lixiviant and flyash to lixivaint ratio. Lead and cadmium In the leaching solution is recovered by cementation with zinc dust. Leaching and cementation experiments have shown that zinc concentrations suitable for electrowinning, > 15 g/liter, can be achieved. Experiments have also been performed to determine the effects of pH, particle size of the zinc dust used, quantity of zinc added and dissolved impurities on the cementation kinetics. After recovery of lead and cadmium, electrowinning or electrowinning coupled with solvent extraction can be used to recover zinc. A process flowsheet is presented.

Jan 1, 1991

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By P. R. Khangaonkar

The variety of intermediates, middlings, complex materials and wastes produced in the conventional processing of tin ores as experienced in the tin industry in South East Asia is reviewed. The problems associated with the treatment of these materials so as to produce useful products by hydrometallurgical or pyro-cum-bydrometallurgical approaches are discussed. Results of treatment of amang middlings consisting of cassiterite, struverite, ilmenite, zircon, monazite etc by chlorination with carbon tetra chloride are presented. The efforts to leach tin without letting iron coming in, by alkali leaching of certain wastes of tin processing are also briefly indicated. It is felt that pyro-cum-hydrometallurgical approach can help a viable treatment of these materials so as to obtain usable or value added products.

Jan 1, 1994

By Kazuyoshi Shimakage, Shinji Hirai, Kenji Wada

"An amorphous zirconium oxide coating was prepared by the sol-gel process using zirconium tetra-n-butoxide on the surface of aluminum to improve the corrosion resistance to salt, acid and alkaline attacks. The coating films formed on the smooth aluminum substrates under UV-irradiation indicated an excellent corrosion resistance for salt, acid and alkaline attack tests. For example, the corroded area of coating film in salt attack test for 3600ks in the order of sol-gel coating· film< chromate film <boehmite film, and the sol-gel coating film had the best corrosion resistance. The coating film prepared on the coarse aluminum substrate by a boiling treatment after heat treatment at 573K also had greater corrosion resistance, and a water-avid surface appeared a contact angle of approximately 3°.IntroductionAs given in a previous paper1; a composite film consisting of a porous layer of anodically grown aluminum oxide filled with amorphous zirconium oxide and an amorphous zirconium oxide coating layer deposited thereon via the sol-gel process utilizing the dip-coating technique, was prepared to improve the alkaline corrosion resistance of aluminum. The alkaline corrosion resistance of these composite films was increased in the range of 24 to 50 times those of conventional anodic oxide films anodized in sulfuric acid. As a result, it was proved that heat treatment at 573K after dip-coating was an important process to .remove organic component from gel film and to accelerate the densification of coating layer. Furthermore, the effect of ultraviolet (UV) irradiation at ambient temperature on the densification of coating layer was also examined to lower the heat-treatment temperature2.Then, a sol-gel film prepared by UV irradiation at ambient temperature indicated that alkaline corrosion resistance of aluminum was superior in the range of 2.4 times to 2. 6 times that of the conventional composite film heated at 573K."

Jan 1, 2000

By R. E. Brewer

Pilot scale flotation tests were conducted with a l?ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pet of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated. The tailings were first water leached at approximately 60? C, and the water-leached tailings, containing approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH&apos; and sodium sulfide addition on gold flotation recovery and redox potentials were examined. Maximum gold flotation recovery, 36 pct, was achieved at pH 8,5 with a sodium sulfide addition of 0.18 Ib/st. Overall gold recovery by leaching and flotation was in the range of 70 to 80 pet.

Jan 1, 1989

By Nickolas J. Themelis

The role of copper in the economy will not diminish in the 21st century. Following the tenets of industrial ecology, production and use of copper must take into account both human needs and also how to minimize "collateral" effects on the environment. Dispersive uses will be phased out and post-use recovery of copper will increase. This will result into an advantage for smelting processes that can accommodate mixed metal scrap and waste streams. The bath smelting processes of Noranda and Mitsubishi will continue to make progress but the dominance of the Outokumpu flash smelting will not be challenged until the Noranda reactor overcomes the obstacles to the direct production of copper, thus eliminating the need for a converter.

Jan 1, 1999

By J. Etay, S. Daugan, Y. Fautrelle

"New type of electromagnetic parametric instabilities arising at the free surface of liquid metal in the presence of a low frequency magnetic field are presented. First, the mechanism of the instability is analysed in an idealised case. Then, the experimental device working with mercury is described. Various shapes, both regular and irregular, of free surface are found. A experimental stability diagram is obtained. Measurements of the deformation performed on photographs are compared with physical orders of magnitude.IntroductionWhen a liquid metal pool of electroconductivity a is submitted to an A.C. magnetic field B = B0 cos mt, electrical currents j are induced in the liquid metal and interact with the applied magnetic field to create electromagnetic body forces F = j x B. Those Lorentz forces comprise both a mean value (time average) and an oscillating part. Those forces are widely used in many metallurgical processes to stirr a liquid metal or to control its free surface, e. g., in aluminium continuous casting or electromagnetic levitation problems (1-3). When liquid metal free surfaces are submitted to AC. magnetic fields, the shape of those interfaces may interact with the applied field and leads to a various instabilities. A review of these instabilities may be found in Fautrelle (4). That instabilities may be a problem for the control of processing as electromagnetic levitation or quasi-levitation."

Jan 1, 1999

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By Jacob Bummer, Greg Roset, Dayle Flynn

"IntroductionStillwater Mining Company operates a Precious Metals Smelter (PMS) located in Columbus, Montana USA. The PMS processes iron, copper, and nickel sulfide bearing concentrates containing platinum, palladium, gold, and rhodium. The concentrates are produced from two mines in the Beartooth Mountains located in south central Montana. The PMS utilizes a 7.5 megawatt 3-in line electric furnace to smelt the concentrates, and two Top Blown Rotary Converters (TBRC's) to remove iron. In addition to the mine concentrates, the PMS also processes various forms of Platinum Group Metal (PGM) bearing recycled catalyst. The sulfide matte produced within the electric furnace and TBRC's acts as a collector for the PGMs. Throughout the operation of the PMS, there are three different forms of molten material that are processed through the Stillwater Granulation system: TBRC matte, TBRC slag, and electric furnace matte. This paper describes the operation of this granulation system.Tapping the FurnaceWhen a sufficient level of molten PGM bearing matte has been reached within the inner volume of the electric furnace, the molten material is ""Tapped"". Tapping requires drilling into the electric furnace until reaching the molten matte phase. The matte phase will drain out of the drilled hole through a graphite launder into a 5 ton refractory lined ladle. Once the ladle is full, the tap is plugged with a mud gun."

Jan 1, 2012

By Supachai Surapunl

The distribution behavior of VA minor elements (As, Sb and Bi) in the smelting stage of the Mitsubishi process were evaluated thermodynamically based on thermodynamic data and operating data. The fractional distributions between the gas, slag and matte phases considered as the degree of vapor saturation of l.0 are as follows: 53.8, 27.2 and 19% for As, 23.6, 56.6 and 19.8% for Sb, and 91.3, l.1 and 7.6% for Bi, respectively. Arsenic is mostly distributed to the gas and slag phases. It is effectively eliminated by volatilizing and slagging. Antimony is mainly in the slag phase, which is suitably removed by slagging. Bismuth is easily vaporized to gas phase. The degree of vapor saturation has a large effect on the distribution behaviors of the three elements between the three phases. The amount of a minor element in the charge has an effect on the distribution of As but no effect on the distributions of Sb and Bi. Increasing matte grade and temperature results in the change of distributions for As and Sb, significantly. The change in the distribution ratio between slag and matte phases also considerably affects the distributions of As and Sb. The distribution behavior of Bi is not significantly changed by the change in matte grade, temperature and distribution ratio.

Jan 1, 2003

By C. O. Bounds

The magnetic properties of (NdDy)15Fe78B6 sintered magnets have been evaluated using powder prepared by Inert gas atomization. The atomized powder had a particle size distribution from 1 to approximate 1000 microns. The as atomized powders have been sieved into, coarse, intermediate, and fine fractions; magnetic properties were evaluated for the as produced powder and each fraction. A B, of 11.7 kG, a Hci of 11.0 kOe and a BHmax of 32.5 MGOe was -obtained on a sintered magnet made from the as-atomized powder. The magnet made from coarse powder exhibited a slightly higher B, of 12.1 kG, while that from fine powder showed a decrease in B, to 11.2 kG. Hydrogen decrepitation has been utilized to study its effect on the magnetic properties. Finally, cast ingots with a definite columnar structure have also been used to compare the magnetic properties of magnets of the same nominal, composition but of different alloy preparation process. Hydrogen decrepitation does not appear to improve the magnetic properties of magnets made from thin cast ingots. However, it does show a significant improvement in the Hci of magnets made from the atomized powders. Possible causes for the differences in the magnetic properties on magnets made from each process have been discussed in the paper.

Jan 1, 1992

By Xin Zhang, Mengqi Li, Hongxu Li, Xinrong Zhang, Hao Bai, Ning Li

"Organic Rankin Cycle (ORC) is an effective technology to transform low-grade energy resource into electricity. In this paper, based on thermodynamic principle, considering the waste heat resource lower than 120°C, thermodynamic properties of ORC with working fluids ofR245fa, mixed R21/R245fa and mixed Rl52a/R245fa were assessed. The results show that high evaporation temperature contributes to improved system performance. The Rankine Cycle that uses R21/R245fa can increase net cycle output, thermal efficiency and exergy efficiency by 3.02%, 2.35%, and 4.44%,respectively, as compared to that with pure R245fa. When using Rl52a/R245fa as working fluid, the net cycle output can increase by 3.83% at most, while the thermal efficiency decreases by 8.7%. These results indicate that R21/R245fa has a good advantage in improving the cycle thermodynamic performance.IntroductionOrganic Rankine cycle is usually used for low temperature power generation, and is applied to the conversion of geothermal energy, low-temperature solar energy, ocean thermal energy and industrial low-temperature waste heat etc. Traditional Rankine cycle is quite mature already, however, organic working fluids would affect significantly the general efficiency of the entire thermodynamic system. Thus, selection of proper working fluids and development of new highperformance cycle is becoming important."

Jan 1, 2013

By Tatsuzo Kitamura

The tank house of Tamano refinery, that started its operation in January, 1972, was constructed incorporating the application of Periodic Reverse Current (P.R.C.) from the outset of design works. In 1973, the production of electrolytic copper came up to 8,000 mtpm, a sharp increase ds compared with the designed capacity of 7,000 mtpm, and successful operation has been achieved up to the present. P.R.C. has been employed for the purpose of raising productivity level and reducing copper inventories. Since there were various problems in P.R.C. application to such a large sized cathode as 1 m x 1 m, special attentions were paid to the following items: -Development of a unique bus bar to make an electrolytic current to each electrode as uniform as possible. -Improvement of circulating method of electrolyte. -Application of high-performance equipment to realize a uniform spacing between anode and cathode. Owing to these creative technical developments mentioned above, technical level for operation up to 350 amp per sq m of cathode current density has been established. The quality of electrolytic copper, which was a matter of interest, has been proved to be as excellent as those of conventional electrolysis products through a long term supply to the field of SCR and Dip forming where high levels in quality are required.

Jan 1, 1976

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FexAs2O2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS203 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000

By J. M. Zhuang

Lignosulfonates, by-products of the sulfite pulping process, have been utilized in a process [1, 2] to treat acidic rock drainage (ARD). This process is referred to as the LignorTM process. In the present study, lignosulfonates were found to protect lime from developing an external surface coating, and hence to favor its dissociation. Further, the addition of lignosulfonates to ARD solutions increased the clotting and settling rate of the formed sludge. The capability of lignosulfonates to form stable metal-lignin complexes makes them very useful in retaining metal ions and thus improving the long term stability of the sludge against leaching. The LignorTM process involves metal chelation with lignosulfonates, ARD neutralization by lime to about pH 7, pH adjustment with caustic soda to 9.4 ? 9.6, air oxidation to lower the pH to a desired level, and addition of a minimum amount of FeCl3 for further removal of dissolved metals. The LignorTM process removes all concerned metals (especially Al and Mn) from the ARD of the Britannia Mine (located at Britannia Beach, British Columbia, Canada) to a level lower than the limits of the BC Regulations. Compared with the high density sludge (HDS) process, the LignorTM process has many advantages, such as considerable savings in lime consumption, greatly reduced sludge volume, and improved sludge stability.

Jan 1, 2003

By H. V. R. von Rhaden

Systematic quantitative X-ray diffraction analyses performed on diamond-drill cores originating from the Aandenk formation at the Loraine Gold Mine, located in the Welkom goldfield, Orange Free State, South Africa, have revealed the presence of a number of phyllosilicate mineral assemblages which have not hitherto been reported from this region. Rectorite, a regularly interstratified 1:1 mica-montmorillonite "swelling clay", is found to occur together with paragonite, muscovite, pyrophyllite, kaolinite, and chlorite in highly-altered friable rocks. The presence of rectorite in mill feeds may have potentially serious implications with respect to gold recovery. Quantitative X-ray diffraction analysis for phyllosilicates can be used as an aid to correlation, and also to guide the widths of stopes in underground mining. Rectorite has a unique mode of origin, which is discussed.

Jan 1, 1991

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By Y. K. Rao

Relatively pure crystalline lead sulfate (PbSO4) can be produced by chemical vapor transport from an impure source such as the lead-acid battery paste or the roast-ore-leach-residue from a hy¬drometallurgical process-route. In a closed-reactor, transport of matter is induced by a tempera¬ture-gradient and the steady-state transfer rate can be calculated using the data on the standard free energies of formation for the species present and the pertinent binary diffusion coefficients. The present work focusses on chemical vapor transport in a tubular reactor (1.4-cm inner diameter x 10-cm long) with the source- and deposition-ends held at 850°C (T,) and 750°C (Td), respectively; PbC12(g) is the &apos;solvent&apos; or &apos;transport agent&apos; and NiSO4(s) placed in the source-zone -serves to maintain a sufficiently high S0,-potential such that the stability of the lead sulfate species is ensured. For the purposes of analysis, the gas-phase in the reactor is assumed to consist of eight species: H2O, PbC12, SO3, SO2. O2 HO, C12, and PbC14. The reaction between C12(g) and PbSO4(s) in the high-temperature source-zone produces PbCl2, SO2, and 02; four more reaction-equilibria in the same zone yield other species. In the low-temperature deposition-zone, reaction equilibrium involving PbC12, H2O, and SO, leads to the nucleation and growth of PbSO4 crystals; three other reaction-equilibria occur in this zone. By employing the virtual equilibrium state for the end-zones and coupling it to the Stefan-Maxwell diffusion equations for each of the gas species, the respective partial pressures for these, in the source- and deposition-zones, are computed at steady-state. From these data, the molar fluxes of PbCl2. PbCl4, and so forth, are determined. Allowing for the transport-enhancing effects of thermal convection, the net transport rate of lead (or PbSO4) is duly calculated for specified initial conditions. The predicted rates show very good agreement with measured rate data reported in the literature [ V. Plies, T. Kohlmann and R. Gruehn: Z. anorg. allg. Chem, 568, 62 (1989)

Jan 1, 1995