Search Documents

By Syd Peng

It is necessary to fully understand roof geological features in order to design a proper roof support system for underground coal mines. These geological features include: rock type, rock strength. rock layer interfaces, voids, cracks, and bed separations. Traditionally, engineers have relied heavily on the use of surface borehole log data to identify geological features. Since surface boreholes very expensive to be drilled in close spacing, log data are often insufficient to provide detailed information on the roof geology. Recent advances in control technology have made a large amount of roof bolter drilling data available to mine personnel. These data can be obtained during normal roof bolt installation cycle with little or no interruption in mining operations. This research project has developed several methods to identify geological features in a mine roof from measured drilling parameters. Power trend line analysis can be used to locate discontinuities and interfaces in mine roof. Power averaging can be applied to determine the relative strength of roof strata. Thrust trend line analysis can be used to locate fractures in mine roof. The results of these methods are combined to produce a mapped roof geology In a production environment, manually interpreting and managing collected drilling parameters is not practical since hundreds of holes will be drilled during a production day. A new software package, MRGIS, has been developed to allow mine engineers to make use of the large amount of roof drilling parameters for roof support design. An actual underground test site is presented to demonstrate the analysis and display capabilities of MRGIS.

Jan 1, 2003

By Salah Badr

Longwall mine layouts with their entries, chain pillars, face support systems, advancing mining faces and compacting gobs represent a geomechanically complex mining operation. Geomechanical aspects are further complicated if mining occurs at depths exceeding 350 m, as stresses induced adjacent to the excavations exceed the unconfined strength of the coal and result in fracturing of the sidewalls of entries and chain pillars during development. Traditional methods of geomechanical analysis, whether empirical or numerical, are unable to represent such behavior satisfactorily. Achieving some meaningful results requires explicit representation of the three-dimensional boundary conditions and implementation of appropriate constitutive models for the rock mass. This paper describes a numerical modeling methodology for deep longwall mines operation using the FLAC3D finite difference de, which incorporates a strain softening constitutive law for modeling failure of coal. An important aspect of the modeling method includes accounting for stress relief provided to the pillars and entries due to the increasing load applied to the compacting gob.

Jan 1, 2003

By Duk-Won Park

The excavation of a longwall panel causes a continuous stress redistribution in the surrounding strata for every face advancement. The understanding of the behavior of rock to high level of stresses is instrumental to the structural design of underground mines. In order to achieve a realistic analysis of the behavior of strata, the three-dimensional finite element method is frequently used. Also the model developed for the analysis has to be designed large enough to represent the influenced strata in the study area and a sufficient number of elements has to be used to provide detailed information on the stresses and displacements. Due to the size of the model and its numerical solution the CRAY X-MP/24 supercomputer has been used for this study. The mine site selected for the analysis is a coal mine located in the Black Warrior Basin in Alabama. The mine has two longwall sections at a depth of 2,000 feet with various dimensions of chain pillars, including yield pillars. Various research programs at this mine have been carried out by Park et. al. ( 1984 ). Therefore data were already available on the geology, and physical properties of rock and coal. In addition a rock testing program has been carried out to obtain rock mass classification parameters. The progressive failure technique has been utilized to simulate stress redistributions. The failure criterion after Hoek and Brown ( 1980 ) which is based on rock mass behavior was used for the iterative technique. Simulated stress redistributions are therefore very realistic. In order to automate the process involved in the application of progressive failure technique, a computer program has been developed. The combination of a large scale three-dimensional finite element model and the automation of progressive failure simulation provided a tool that can generate a large amount of information related to the behavior of rock and coal as a response to a longwall mining operation.

Jan 1, 1989

By David C. Laurence

in March 1999, the School of Mining Engineering at the University of New South Wales carried out a series of underground trials using " Evermine", a South African developed two-part water based polymer membrane. The aim of the trials was to determine the potential of a spray-on polymer membrane such as Evermine as an alternative to conventional rib support systems The mine selected was Angus Place colliery, reputed to have some of the worst ground conditions of any Australian underground coal mine. Ribs at Angus Place are supported by conventional pattern bolting supplemented by wire mesh. The trials indicate that there is significant potential for the introduction of polymer membranes into the underground coal minim; industry Initial results indicated that ribs that had been sprayed exhibited less displacement and spalling than unsprayed ribs. particularly when subjected to abutment loads from an approaching long-wall Further research will he required to conclusively rate the performance of Evermine in comparison to other products in the market and the long term performance of the product

Jan 1, 2000

By William G. Pariseau, Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"This contribution describes development and application of a user-friendly finite element program, UT3PC, to address three important problems in underground coal mine design: (1) safety of main entries, (2) barrier pillar size needed for entry protection, and (3) safety of bleeder entries during the advance of an adjacent longwall panel. While the finite element method is by far the most popular engineering design tool of the digital age, widespread use by the mining community has been impeded by the relatively high cost of and the need for lengthy specialized training in numerical methods. Implementation of UT3PC overcomes these impediments in three easy steps: First, a material properties file is prepared for the considered site. Next, mesh generation is automatic through an interactive process. A third and last step is simply execution of the program. Examples using data from several western coal mines illustrate the ease of using the application for analysis of main entries, barrier pillars, and bleeder entry safety.INTRODUCTIONRational design of safe underground entries and crosscuts, barrier pillars, and bleeder entries begins with a site-specific analysis of stress. An analysis of stress identifies the critical regions of high-stress concentration where yielding is likely and additional or more focused ground control measures are needed. This analysis also identifies regions where stress concentration is low, and risk mitigation is less urgent. Displacements induced by mining, including roof sag, floor heave, and pillar squeeze, are also of importance to stability. The popular finite element method is well-suited for such analysis and has been in use for studying coal mine engineering problems since the late 1960s (Dahl, 1969). The method has been taught in undergraduate engineering curricula for many years and offers an alternative to existing design procedures based mostly on rules of thumb, empirical methods based on mine data, and predigital-age concepts of strata mechanics. However, despite the versatility of the finite element method, usage has been limited, mainly because of the cost of the software and the required training in numerical methods.The program UT3PC (Pariseau, 2017) has evolved from early two-dimensional versions in the era of mainframe computers. These early versions were still quite limited using only a few hundred elements that required overnight turnaround times. Recent versions of UT3PC are convenient and efficient desktop programs that use several million elements. With the advent of personal computers in the mid-1980s and subsequent increase in computer speed, expanded memory, and lower costs, applications for mining increased in three-way cooperative projects among industry, the former U.S. Bureau of Mines, and academia. The Spokane Research Center of the U.S. Bureau of Mines, in cooperation with the University of Utah, developed a two-dimensional desktop finite element program, UT2PC, available to the mining community in 1991. This was a short course offered at the 1991 SME Annual Meeting in Denver, CO."

Jan 1, 2017

Since the initial development and trials of FLEXIBOLT flexible roof bolts, further comparative testing and product development has been completed as part of the changeover to this roof support system at two Australian longwall operations, Ellalong and Angus Place Collieries. Details of the practical implementation of FLEXIBOLTS at both collieries are outlined together with their impact on roadway development rate productivity. At Ellalong where fully encapsulated 2.1 m long bolts are used, the reduction in bolt density is discussed with respect to both support system design and work force acceptance. The impact of shear deformation on bolt loading is described. Bolts longer than the working height have been required at Angus Place to achieve a suitable bolt anchorage horizon. Details of the long hole drilling and the benefits of a two stage grouting procedure are outlined. Improvements in roof conditions which have resulted from the inclusion of FLEXIBOLTS into the overall roof support strategy at Angus Place are described. Their importance to the viability of the Angus Place operation is also highlighted.

Jan 1, 1994

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By Bruce K. Hebblewhite

Tower Colliery is a longwall mine operated by BHP Coal Illawarra Collieries, Southwest of Sydney, Australia It mines the Bulli Seam at a depth of approximately 450m. The surface topography overlying the mine consists of several steep-sided river gorges, up to 68m in depth, which run at oblique angles across a sloping terrain Apart from some light rural development, the surface land is essentially natural bushland, but is traversed by a major freeway. This crosses one of the gorges on twin, six-span, box-girder bridges, with bridge piers up to 55m in height. Consequently, a major surface subsidence monitoring program has been in place for several years now, including intensive conventional, GPS and E DM surveying, plus real-time monitoring of critical components of the bridge structure. Although the bridge and freeway are outside the conventional angle of draw' subsidence influence criteria, and have seen only negligible vertical deformation as a result of mining, there has been widespread evidence of regional horizontal deformation of the land surface, large distances away from the mining area The effect at the bridge has been well within acceptable tolerances, primarily because of the regional nature of the movements, with very little differential movement observed at the bridge piers Gorge closure and evidence of large headlands of land moving `en masse' have been observed. Horizontal movements of hundreds of millimetres have been recorded in some locations where gorge closure has been monitored. Possible explanations of these movements include one or a combination of mechanisms such as pre-mining stress relaxation. valley notch effects, valley bulging, regional joint patterns, movement toward active goaf areas, vertical gorge shearing' and shear failure of horizontal bedding planes below the surface This paper presents a case study of the regional horizontal ?subsidence displacements? measured during mining. and a discussion of the possible explanations for these phenomena

Jan 1, 2000

By Hamid Maleki

A novel ground control program has been developed at Plateau Mining Company through five years of geotechnical investigations. The study was initiated to determine the causes for roof stability problems and to develop alternative support and monitoring systems for increased safety and productivity. From systematic roof fall observations, extensive geologic mapping, roof drilling and monitoring ground movements along gate entries of four longwall panels, a sand- stone channel system was detected and shown to impact roof stability. In particular, underlying mudstones up to seven feet thick experienced instability due to differential compaction and load transfer from the gob. Roof bolter operators were trained to report roof lithology for mapping channel positions into the roof and for selective use of longer bolts. This boosted operator morale, and improved ground conditions. Monitoring rates of roof movement is used in these areas for detection of instability and for application of secondary support: This has significantly increased safety and productivity.

Jan 1, 1987

By A. Mahyera

BETTER ROOF SUPPORT During the last decade, resin-grouted roof bolts have taken a substantial foothold in the coal mining industry - now accounting for about one-third of all bolts installed annually, due to the improved roof support. However, the high cost, toxicity and flammability of the resin cartridges appear to be a limiting factor in even greater use of such bolts. Terra Tek, Inc. has, over the past few years, been developing a novel roof bolting system to mix/inject a very fast-setting and high strength inorganic cement into bolt holes and install point-anchored or full-column grouted rebars - all automatically and at substantial cost savings. This grouting system utilizes a unique method to mix the grout ?in-the-hole?. It has been integrated with a conventional bolter, retrofitted with an indexing-head mechanism and an on-board pneumatic computer to sequence and Control the drilling, grouting and bolting. Cycle times are the same or better than for a resin system. Following laboratory testing/development, the prototype system has undergone field trials in a Utah coal mine. A description of the bolting system, results of pull-tests in the laboratory and field, and economics and productivity gains with this system in comparison to a conventional resin-cartridge bolting method are presented. The relationship of this technique to improved roof control is also discussed.

Jan 1, 1984

By W. C. Smith

Over the past several years, the Bureau of Mines has conducted studies on the performance of fully grouted resin bolts In underground mines. The effectiveness of resin-grouted bolts in maintaining a competent roof, even in weak rock, has been well documented in the literature. Recent Bureau studies have evaluated the affects of shortened grout columns on bolt behavior in a variety of rock types (1, 2, 3). The application of partial grout columns to primary roof support systems has been introduced as a viable alternative to fully grouted bolt systems in some mines. The point-anchored resin bolt and combination bolt represent such alternatives. While both systems usually employ some mechanical interlocking system, their primary difference lies in the length of resin column used. Point- anchor systems rely on an anchoring device that is a short length of resin column of 2 feet or leas. Combination bolts, on the other hand, often require 3 feat or more of resin column. Resin migration into voids and fractures intersecting the borebole wall is a major problem when installing fully grouted bolts in weak roof rock and can result in a reduced column length that provides reduced anchorage. The relationship between column length and anchorage integrity deserves closer study. The Denver Research Center of the Bureau of Mines has examined the load- carrying capabilities of resin-grouted bolts in weak strata. Pull tests were performed on about 900 resin-grouted, 4- foot-long bolts with column lengths ranging from 6 to 48 inches. The practical performances of 8 different column lengths were evaluated for 10 mines under in sit" conditions using data obtained from standard pull tests. In addition criteria are discussed, including engineering properties of the host rock for designing safer and more effective grouted bolt installations.

Jan 1, 1987

By D. A. Payne

Large excavations, such as Iongwall panels, result in extensive vertical stress redistribution in the surrounding strata. The large abutment stresses developed may produce damage to pre-existing or planned excavations in the same seam or in seams above and below the workings. Knowledge of the magnitude and location of these stresses is therefore important in the design of mine openings; pillar sizes for panel and pillar layouts, roof supports in longwall gateroads and workings over or above pre-existing or planned extraction in adjacent seams. In an attempt to reduce costs, the Cape Breton Development Corporation (CBDC), a Federal Crown Corporation responsible for operating two retreat longwall coal mines, examined the potential for either interpanel barrier pillar width reduction or entire pillar elimination by the adoption of dual life gateroads for the longwall panels. In order to assess the potential for reduced interpanel barrier widths or total elimination, an investigation of the redistribution of vertical stresses around longwall panels in the Sydney Coalfield was established. The study was conducted jointly by the Cape Breton Coal Research Laboratory (CBCRL), of CANMET (a division of Natural Resources Canada) and the Denver Research Center (DRC) of the United States Bureau of Mines. The program included monitoring of vertical stress changes around longwall panels and gateroad behaviour in two seams. USBM-style hydraulic borehole pressure cells connected to chart recorders for continuous monitoring were deployed at four sites, two at Lingan Colliery and two at Phalen Colliery. This report describes the investigations conducted at Phalen Colliery. Contoured plots of stress redistribution around two sites are presented.

Jan 1, 1995

By Christopher Mark

The Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. The study described in this paper was performed in a 1200 ft long, experimental headgate section which contained three pillar designs: - a three-entry, yield-abutment pillar' system, - a four-entry, yield-yield-abutment pillar system, and - a five-entry, all-yield pillar system. As the longwall mined by the experimental section, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The results of the study indicate that the all-yield system performed at least as well as, and probably better than, the two abutment pillar systems.

Jan 1, 1988

By Reha Ozel

The stability in longwall faces depends on the interaction beman the roof strata, face supports and floor strata. The load distribution on the other hand, depends upon relative stiffness of the three supporting elements namely, the coal face, support and gob. Therefore, in defining support requirements, it is particularly important to analyze the strata loading, the face convergence and the controlling mechanism provided by supports. The controlling mechanism however, depends on the type and characteristics of supports used in long- wall faces. The design guidelines presented in this paper have bean developed based on a number of strata control oriented projects carried out in Turkey, load and convergence measurements carried out in 10 longwall faces, in Zonguldak Coal Region, and procedures given in literature. Evaluation of load and convergence measurements, and analyses of face supports were carried out by means of a computer program, called L0NGWAI.L-MEW, developed by the authors. The output of the design analyses include the following: (1) estimation of support capacity for roof supports namely; individual hydraulic props, chock-type power supports and various types of shield supports, and (2) analysis of loading conditions and response of shield support components in terms of stability and structural integrity.

Jan 1, 1990

By John W. Fredland

Conducting mining operations under a body of Water can create hazardous conditions for miners. The potential for a sudden inrush must be considered and abnormal ground control conditions can be encountered. This paper synopsizes the factors which mine operators should take into account when evaluating whether an inrush may occur. It addresses the applicable Federal regulations and discusses some items which coal operators should consider in applying for a permit, Through collecting and analyzing the pertinent information, the likelihood of encountering problems can be judged. Through proper mine planning, the potential for creating hazardous conditions can be mitigated.

Jan 1, 1982

By Clarence O. Babcock

Since Vicat in 1833, the width to height ratio of a mine pillar has been taken as the fundamental variable in pillar design. From work in the laboratory by many investigators testing rock, Coal and concrete samples, it has been concluded by some that pillars with a width to height ratio of 10 to 1 are indestructible. It has also been concluded that a constrained core exists within the pillar which increases the pillar strength. The role of the roof and floor, if mentioned at all, is often noted in an incidental way. In the present work on laboratory testing of model pillars on concrete, coal, and rock instrumented with special strain gages, it was concluded that the end constraint and not the width to height ratio is the significant variable in determining the pillar strength. In tests where the end constraint is steel, a large compressive stress is produced on the horizontal plane of the pillar, and this effect increases as the width to height ratio is increased, resulting in an increase in pillar strength. If the end constraint is not steel but something with a small Young's modulus, the state of stress in the horizontal plane may be tensile, increasing as the width to height ratio increases, resulting in a decrease in pillar strength. Related to mining, the results are that a large width to height ratio pillar is strong for strong roof and floor and weak for weak roof and floor. That is, the roof and floor and not the width to height ratio determine the pillar strength. The confined core condition should be verified by testing if large pillars are to be used. If there is no confined core or the pillar is in tension, smaller pillar sizes should be used. The final conclusion is that the geometry alone is meaningless in pillar design.

Jan 1, 1984

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By Gift Makusha

The Witbank Coalfield in South Africa contains up to five economically viable coal seams. These seams have been mined continuously for over 100 years and the reserve in now becoming depleted. The normal mining method has been bord and pillar with examples of stooping. The situation now occurs where the formed pillars, left to maintain stability, have a higher quality than the coal that is left in the unmined reserves. Where the reserves are less than 70m deep and continuous over several kilometers, opencast mining is being successfully applied. After several years of investigation, Anglo Coal has identified blocks of coal that warrant investigation with regard to pillar extraction by underground methods The proposed method is pillar extraction using Mobile Roof Supports (MRS) It is proposed to mine three panels at a depth of 120m, by keeping the panels narrow and sub-critical. The sub-critical layout does not allow caving to surface and more stress is thrown onto the barrier pillar rather than the face pillars. The sub-critical span is anticipated to be 100m. The paper describes the full geotechnical investigation, including numerical modelling, instrumentation and drawing on the local South African experience of shortwall mining. The project will be unique in that pillars were not designed for pillar extraction and have low factors of safety (l.4 - 1.8) and width to height ratios of less than 4. The mining height will be approximately 4-4 5m, and this represents "new" operating heights for Mining Roof Supports. The required equipment was ordered in late 2002 and pillar extraction is anticipated to begin in June 2003.

Jan 1, 2003

By T. N. Singh

With a view to producing increased target output every year, Indian coal mining industry is fast moving towards mechanisation but the present approach of mechanisation suffers from lack of standardisation, mainly due to nonavailability of the cutting data for various machine/rock combinations. The coal seams of the country are relatively hard in nature and the coaling machines are reported to be affecting production and productivity of the coal mine and the very trend of mechanisation. This paper presents the result of extensive study performed to visualise the cutting characteristics of coal seams of compressive strength ranging from 20 MPa to 65 MPa. In a specially designed drag bit type coal plough rig, continuous recording of cutting forces was done with the help of a microprocessor based data logger and the specific energy of cuttability was evaluated at different depth of cut and speed of cutting. The geomechanical properties such as compressive strength, orientation and frequency of cleats etc. and different indices of coal seams were measured in the laboratory and field and relationship was developed for easy determination of specific energy.

Jan 1, 1992

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984