Search Documents

By D. W. Wu, M. T. Haque

A novel impedance probe was commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mudline, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mudline information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are reviewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2002

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By R. Latifovic

Assessment of the possible impact of existing and future mining projects located in remote areas may be difficult and costly. This may have an adverse effect on the process of issuing mine permits and development of new mines. A remote sensing based land cover change assessment methodology presented in this paper is a promising avenue to render this process more meaningful, precise and affordable. It has been applied to a case study of the Oil Sands Mining Development in the north-east of the Canadian province of Alberta. Recently, the Athabasca Oil Sands Region (AOSR) is a place of unprecedented growth of open-pit mining operations. This study was focused on the primary impact onto the landscape and vegetation resulting from exploration and, mining development. This impact was assessed using an information extraction method applied to two LANDSAT scenes. The analysis based on derived land cover maps shows a 8.64% decrease of natural vegetation in the study area (715,094 ha) in 2001 relative to 1992. It is demonstrated that the methodology presented here provides reliable results and is fully applicable for the assessment of the environmental impact of large scale mining operations.

Jan 1, 2006

By Adrian Brown

Groundwater inflow and impacts have become major aspects in the permitting and operation of many gold mines. First, the hydrothermal or placer genesis of many of the orebodies being investigated or produced today almost guarantees that mines will be "wet", involving groundwater control as part of operations. Second, the style of ore deposition a1 so often involves a1teration of the host rock, resulting in relatively weak, low permeabi1ity materials that require extensive groundwater pressure control for stable mining. Third, the location of many mines in arid areas guarantees that impacts on water resources will be matters of key focus during permitting and operation. However, groundwater control and protection is a technically difficult area and often involves managerial decisions and activities that do not fit comfortably into traditional mining. In an attempt to overcome some of these difficulties, this paper provides a guide to mine managers and hydrologists as to appropriate strategies for designing, setting up, operating, and evaluating groundwater programs at gold mines that get the job done and are cost effective.

Jan 1, 1988

By E. G. Kelly

Many methods of evaluating the efficiency of mineral separations have been described in the literature. In most cases, these present the efficiency as a single number. This paper argues that single-number measures of efficiency are inadequate because they seldom allow reliable comparisons, and are unlikely to correspond to the optimum operating conditions. To realistically make comparisons, it is necessary to distinguish the particle-induced component from the equipment- induced component. In a number of situations where the separating property can be identified (such as in gravity concentration and classification), this can often be done. However, in more complicated systems, such as flotation, this has not been possible. A technique is described whereby particle and equipment contributions to efficiency can be distinguished without the need to define the separation property. Because smelter schedules define a boundary correlation between grade and recovery, they generate some of the better single¬-number measures of efficiency, but even these have limitations.

Jan 1, 1991

By L. Vandamme, J. H. Curran

A fully three-dimensional hydraulic fracture propagation model, based on the Displacement Discontinuity Technique, is briefly described. Using this model, it is shown that the geometry of a propagating fracture is dependent on several factors, among which the fluid pressure distribution within the fracture plays an important role. The containment of hydraulic fractures is found to be dependent on stress and toughness barriers in the formation. Containment is also observed to be more effective with a decrease of the viscosity, pressure or flow rate of the injected fluid. The three-dimensional layout of the fracture is shown to have a definite influence on the width and pressure distributions within the fracture. The examples considered indicate the need for fully three-dimensional models, as complements to the commonly used two-dimensional and pseudo-three-dimensional models.

Jan 1, 1986

By Gregg Wilkerson

The Blind Springs Hill pumice beds are located 5 miles southwest of Benton, California in the foothills between the Benton Mountain Range and Blind Springs Valley. The best exposures of the pumice are in an area 0.75 miles west of Blind Springs Hill. The pumice is Quaternary ejecta material which came from the rhyolitic volcanoes in the Glass Mountain-Volcanic Tablelands area of Mono County. The pumice beds occur in two distinct layers separated by an unconformity. The upper layer is 0 to 11 feet thick and consists of coarse subangular pumice fragments, some of which are over 1.75 inches in diameter. The lower bed is medium to coarse grained with subangular fragments up to 1.0 inch. The lower bed is 0 to 9 feet thick. Overburden at the Blind Springs Hill deposit varies from 0 to 15 feet. There are approximately 1 million cubic yards of material in the deposit that can be mined. The size distribution in the deposit is mostly fine with only 10.6% of the pumice fragments being over 0.5 inch in diameter, the minimum size needed for stone-wash or acid-wash applications. Suitability of pumice for the textile industry is quantified by standard 15-minute abrasion and absorption tests. In the Blind Springs Hill deposit, the plus 0.5 inch fraction has an abrasion loss of 33% which is too high for stone-wash application but it has an absorption capacity of 36% which makes it suitable for acid-wash applications in the textile industry. The abrasion and absorption properties of this deposit are within the range of those which have been measured for other pumice deposits within the United States.

Jan 1, 1995

By Kadri Dagdelen

Production scheduling of an open pit mine is one of the most important steps in open pit mine planning. The production schedule of a mine defines the distribution of cash flows and as a result directly influences the net present value and overall economic feasibility of a project. It is becoming more and more critical to obtain an exploitation schedule of a deposit such that highest possible returns are achieved from a project. As the mining industry mines lower and lower grade ores, production scheduling is becoming a key item which can make or break a project. Although the need to plan and operate a mine with an optimum production schedule has been obvious for some time, the methods used to obtain such a schedule have not been. There is not a single, mathematically proven, optimum mine production scheduling algorithm which is widely accepted and used today. In an attempt to determine a production schedule which is optimum, a new algorithm was developed. This algorithm, in theory, is based on the lagrangian concepts of mathematics and in practice is based on the parameterization concept of mining. This paper describes the fundamentals of this newly developed algorithm.

Jan 1, 1986

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By Eric C. Schwamberge, Clem A. Pelletier, Deborah L. Muggli, George W. Poling

The Pit Lake at Island Copper has evolved into a 3-layered meromictic system. Acid Rock Drainage (ARD) is collected and injected into the lake at 220 m depth via 2 diffuser systems. In situ dye studies were conducted during 2 differing hydrological regimes in order to determine the behavior of the ARD plume within the Pit Lake. Results indicated that when runoff from the waste dumps was low, the injected ARD remained within the bottom half of the intermediate layer of the Pit Lake, initially below depths of 90 m. However, when runoff from the waste dumps was high, the injected ARD at -220 m depth rose through the intermediate water column layer rapidly, but did not breach the top pycnocline at -10 m depth. Overall, the system is currently performing as a mixing bowl with a strong boundary or cap at the upper pycnocline. maintaining mixing below the 10 m depth water level.

Jan 1, 2000

By V. T. McLemore

The Steeple Rock district in New Mexico is a major epithermal gold-silver district that exhibits district zoning. Five types of ore deposits occur within the district: •base-metal veins (with gold and silver) form the center of the district and occur along the Carlisle fault, •gold-silver veins along northwest-trending faults and outward from the base-metal veins, •copper-silver veins along the margins of the district, •fluorite veins along the margins of the district, and •manganese veins along the margins of the district. Areas of older acid-sulfate alteration occur throughout the district and also exhibit the following zoning: massive silica/chert zone (inner), silicified zone and clay zone (outer). This alteration overlies regional alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow, but older, epithermal hot-springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1996

By H. S. Chang

A three-dimension two-phase (air and dust) computer model was developed to model air velocity and respirable dust distributions in the longwall faces. This paper describes the derivation of the model including the model features, mathematical equations and boundary conditions. Example simulations were also performed for two longwall faces where measured respirable dust and air velocity distributions were available. The results indicated the model can simulate the mine conditions fairly accurately.

Jan 1, 1996

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By Babcock. C. O.

This report presents equations derived from experimental testing to convert borehole pressure cell data from vertical and horizontal cells to the biaxial ground stress changes. While hydraulic pressure cells in boreholes have been in extensive use since 1957, methods of data reduction have been slow to develop. The methods of Sellers (1970) and Bauer et al. (1985), respectively, indicate a linear relationship between cell pressure change and the rock stress change. Lu presented a theory for creep behavior (Babcock et al., 1982). In the present work, in laboratory testing, the logarithm of the cell pressure was related to the stress change in seven elastic materials for a range of Young's moduli of 3.45 to 85.5 GPa (0.5 to 12.4 x 106 psi). The gage response depends upon the setting pressure of the gage, the gage pressure at any time, the rock properties, and the cross-sensitivity of the gage to transverse loading. The setting pressure of the cell should be proportional to the Young's modulus of the rock, the absolute stress can be determined by overcoring in strong rock, and the in situ Poisson's ratio can be estimated in some cases from the cell responses.

Jan 1, 1986

By J. B. Zachwieja, P. E. Richardson, G. W. Walker

The electrochemical nature of mineral-collector interactions and their relationship to flotation have been investigated to develop a better understanding of the factors controlling sulfide mineral beneficiation. Spectrophotometric and electrochemical techniques have been used to examine the reactions occurring on electrodes composed of a bed of bornite particles in the presence and absence of potassium ethylxanthate (KEtX) at a pH of 9.2. The combined techniques showed that KEtX sequentially reacts with bornite by (1) a chemisorption reaction forming ca hydrophobic species between --0.4 and -0.2 V (SCE), (2) an electrochemical oxidation reaction forming cuprous xanthate between -- 0.2 V and the xanthate/ dixanthogen redox potential, and (3) oxidation to dixanthogen when the potential exceeds the reversible value for the xanthate/dixanthogen couple. The flotation response of bornite closely parallels spectrophotometric and electrochemical evidence for adsorption of KEtX by the reactions listed above. The degree of surface oxidation resulting from the formation of iron oxides on the surface dictates the flotation response as evidenced by the fact that oxidized bornite floats at more anodic potentials than unoxidized bornite. The strong correlations between the flotation response, degree of oxidation, and potential indicate that chemisorbed xanthate produces a hydrophobic layer sufficient to float unoxidized bornite, but cuprous xanthate and dixanthogen arc required to float oxidized bornite.

Jan 1, 1988

By Giin-Fa Fuh, Sally A. Shoop

An instrumentation program was developed based on the results of an analytical study of the geomechanical effects of longer longwall face lengths. Boundary element simulations showed that longer face lengths can cause in- creased face convergence and an increase in the shear stresses in the immediate roof. Empirical design methods predict that longer faces will cause little effect on abutment stresses as long as the roof caving is well behaved. On this basis, a longwall face instrumentation program was designed with emphasis on the interaction between face support and ground response for optimizing face conditions. At a 600-foot (183 m) face, five midface shields and two headgate shields were monitored with vary- ing hydraulic pump pressure. The instrumentation included six convergence rods with linear potentiometers to measure canopy-to-toe convergence; fourteen pressure transducers to monitor leg pressures; and two portable data loggers. Similar instrumentation will be in- stalled on a 750-foot (229 m) face for comparison. The results from the 600-foot (183 m) face indicate that a ground reaction curve, as determined from the relationship between the sup- port set pressure and the roof convergence, can be used to optimize the support pressure to control convergence, the key element to ground stability in the face area.

Jan 1, 1986

By D. W. Fohlen, B. A. Filas

The International Finance Corporation (IFC), the private investment arm of the World Bank Group (WBG), requires all IFC-financed projects to comply with its environmental and social policies and guidelines. IFC's review process involves an environmental and social assessment and the implementation of an Environmental Action Plan (EAP) that will set forth the necessary actions to bring the operation into compliance. This paper provides an overview of the environmental and social policies and guidelines that apply to mining projects and examines how WBG/IFC policies and guidelines are applied to mining projects in developing countries. In addition, it includes a review of the increased emphasis IFC is giving to social issues over the past several years based on the existing WBG policies. IFC’s process for the environmental and social review of proposed investments is briefly discussed. The paper focuses on how IFC emphasis has shifted from the traditional environmental and impact mitigation analyses of a few years ago to the integrated social and environmental awareness, action (EAP), and implementation programs (social plans) required today. Today, IFC's focus is to promote sustainable development by investing in projects that directly benefit local communities and the environment. Examples of these changes will be highlighted by a review of recent investments located in West Africa. The goalposts have not moved, but the rules of the game have become tougher.

Jan 1, 2001

By Graham A. Mathieson

A detailed breakdown of capital and operating costs is an essential element in the planning and evaluation of any mining project. The OPCOST System was developed by Golder Associates to provide mining engineers with the facility to synthesize detailed cost estimates for all aspects of an operating or potential open pit mine. The system can also be applied to underground mines equally as well. Such estimates can be prepared at a variety of levels depending on the detail required by the project. The OPCOST System is a suite of computer programs linked through a common hierarchical data base. It simulates the thought and reasoning processes within the quantity takeoff and cost estimation phases of a mining project. The system was developed as a mining cost engineering tool on the basis that it would have to satisfy a variety of purposes, namely:

Jan 1, 1982

By Thomas V. Durkin

About 1.41 kt (45.2 million oz) of gold have been ! produced in South Dakota since 1875. South Dakota's mining laws attempt to strike a balance between economic development and environmental protection. Mining is promoted as an industry while prevention of pollution is required along with reclamation of affected lands to a beneficial use. The South Dakota Department of Environment and Natural Resources' (DENR) system of "one-stop shop- ping" for environmental permits streamlines the permit process. It fosters quick resolutions to compliance problems and helps keep enforcement actions out of the courts. Paha Sapa means "Hills that are Black" in Dakota Sioux. Appearing dark from a distance due to a thick forest of Ponderosa pine, the Black Hills were gold to many people. The exact date that gold was discovered in the Black Hills remains debatable. An inscribed stone tablet found in 1887 near Spearfish recorded these words:

Jan 1, 1998

By S. A. Kupferman

Cement raw materials used in southern California and Arizona cement plants occur in a wide variety of geologic environments. Limestone, the primary material making up 75-80% of the raw materials mix used in cement manufacture, is mined solely from Paleozoic Era deposits. During this time, 570-245 million years ago, vastly more limestone was formed in California and Arizona than at any other time (continent was in southern latitudes). The general geology of each limestone deposit associated with the eight southern California and two Arizona cement plants will be reviewed. Many of these deposits are geologically complex, having been subjected to Mesozoic deformation, metamorphism and instrusive events, along with Cenozoic uplift and deformation. All of the cement plants in this region require the use of secondary additives in order to meet the chemical requirements for cement. The kinds of additives vary greatly, depending upon the chemistry of the limestone deposit, cement specifications, and the cement manufacturing process. In some cases, clay deposits with suitable chemistry on or near the limestone sources are utilized. Where alkali limitations or need for alumina-rich materials exist, then specialty clay deposits are used. Iron-rich sources in the region include iron ore deposits and slag or mill scale from local steel mills. The geologic setting and location of these additives, along with gypsum and silica-rich deposits presently in use, will be mentioned.

Jan 1, 1987