Search Documents

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985

By T. W. Lloyd

Accurately predicting coal seam discontinuities is an important part of modern underground coal mining. Conventional methods of coal exploration sometimes fail to identify rapid variations that may seriously impact mining and quality. Radio Imaging Method (RIM), a geophysical approach to mapping longwall panels, has been developed where electromagnetic signals are transmitted and received though the coal block. The amount of signal loss for a given distance, when compared to the coal seam characteristics, identifies anomalous areas. A comparison of RIM predictions with actual geologic conditions encountered during longwall mining demonstrates the accuracy and usefulness of the data.

Jan 1, 1986

By William E. Cobb

15.1 INTRODUCTION The mine development process, as discussed in Chapter 2, is a series of data gathering and analysis steps. As the mine development process proceeds, information about the geology, mineability, and metallurgy of a particular deposit is continually generated, along with environmental information regarding project permitting status. As data are obtained, checkpoint evaluations are typically conducted to determine the economic viability of the particular deposit. Although the project evaluation process was discussed at length in Chapter 2, a brief review of the process is presented here to "set the stage" for the discussion on economic analysis of heap leach projects. Figure 15.1 (MacKenzie, 1980) presents an overview of the sequential process of mine development. Once the deposit is discovered or acquired, an initial delineation program can be undertaken to expand the project's geologic, mining, and metallurgical data base. At the end of this initial program, the direction of the project is evaluated. The company can either abandon the project, postpone it, develop and mine it, or gather additional data in hopes of improving the project's economic viability. If the company continues gathering data, then another decision point and evaluation will be required. This process may continue until the company either decides to postpone the project or develop and mine it. A project may be postponed indefinitely, typically in hopes of improved metals prices. Certain holding costs, such as land or royalty payments, may be associated with postponement. In general, once a company goes through two evaluations, the project is less likely to be abandoned. For this discussion, it is assumed that the company will undertake initial, second, and third delineation programs to gather sufficient geologic, mining, metallurgical , and environmental data to justify a positive production decision from the second or third economic evaluation. The objectives of the first delineation program will be to confirm and expand upon the available information about the deposit. During the second delineation program, development funds should be directed toward identifying the critical project items (i .e., ore reserves, mineralogy, mineable grade, metallurgical recovery, etc.) that must be resolved before making the production decision. This second economic evaluation can be used to determine which metallurgical concept will be applied to the project: heap leach or a traditional agitation-type leach plant. If the proper work has solved key project concerns in the second program, a production decision may be made from that evaluation.

Jan 1, 1988

By L. Whitby-Costescu

The Shebandowan mine and concentrator, with a capacity of 9072 t/week (10,000 st per week), was opened in 1972 after several years of environmental study and planning. The mine is located in a popular vacation cottage .area about 96 km (60 miles) west of Thunder Bay, Ontario. Undertaken before environmental assessment procedures had become an established requirement, Shebandowan is one of the first Canadian examples of effectively integrating environmental work into overall planning. Although it is an underground mine, many of the environmental considerations are common to open-pit operations, and hence, it provides a case history for the use of all mine planners. Computers can play a part in such studies by simulating the annual production of mine wastes, by on-line polling of environmental sensors and by processing sensor data. Early attention was focused on establishing base-line conditions in a two-year water quality monitoring program. Since production began, water quality monitoring has shown that mining has not caused any significant changes. However, mine drainage disposal arrangements had to be modified in the light of operating experience. There is no townsite associated with the mine, and workers commute from established municipalities. Harmonious relations have been achieved with local cottage residents after their initial fears were dispelled. Plans are ready to begin revegetating the tailings when a sufficient area of dry elevated tailings has been accumulated. Rehabilitation of the land disturbed during development was begun before start-up and was completed during initial operations.

Jan 1, 1979

By Lester E. Sutton

The past three years have been the most difficult period in the modem history of the barge line industry. Having withstood the fuel cost run ups of the late 1970s and the imposition of inland waterways system user fees, the industry has struggled more recently with an overcapacity problem of unprecedented proportions. In responding to these challenges, the industry is undergoing important long-term structural changes, with the various individual barge lines pursuing an array of divergent long-term business strategies. This paper discusses these strategies in terms of their probable impact on the industry as a whole, and argues for the survival of a competitive number of large, national, independent barge lines as the outcome most in keeping with the long-term interests of the mining and minerals industry.

Jan 1, 1986

By F. J. Sotillo

Mineral processing requires good classification of particles to attain an adequate separation of minerals. This is of utmost importance in the case of sulfide minerals. An ideal classification is obtained when particles are separated at a given mesh, which is fixed according to the characteristics of each sulfide ore. Under these ideal conditions, particles coarser than the mesh of separation are recovered in the underflow, whereas particles finer than the mesh of separation are recovered in the overflow. This paper presents the results of pilot plant tests that were performed on Ag-Pb-Zn and on Ag-Au Peruvian sulfide ores using a Density Separator, and the comparison of these results with those obtained using hydrocyclones, under similar operating conditions. The results show that the ratio of circulating load is reduced by 50% by using a Density Separator with respect to that obtained by using hydrocyclones. Moreover, the effect of the improvement in the separation efficiency obtained by using the Density Separator on the kinetics of flotation is also shown. Silver recovery of the Ag-Pb-Zn ore increased by 18% whereas gold grade in the concentrate of the Ag-Au ore is doubled.

Jan 1, 1998

By R. L. Atwood

The structure, properties, and composition of commercial chelating-type copper extractants are examined. Characterization of these extractants was accomplished using organic separation techniques and analytical tools such as NMR and IR. Results indicate that only the trans isomer of the diphenylhydroxyoxime (LIX (R) 64N) is capable of copper chelation. The effect of the structural modification of the extractants on the extraction and stripping reactions are discussed.

Jan 1, 1972

By Peter L. Dunn

With the advent of new high-strength magnetic materials, rare-earth magnetic separators have become more common place for processing heavy mineral sands. In many instances, rare-earth magnets have replaced conventional separators such as electromagnetic cross-belt and induced-roll type machines. This paper will present the results from a detailed test program developed to evaluate the performance of rare-earth drum and roll separators for processing heavy mineral sands. The effect of machine design parameters, such as magnetic element configuration and separator diameter, will be reviewed in light of these test results. The impact of basic operating parameters (i.e. feed rate and roll speed) on separation efficiency will also be presented.

Jan 1, 1999

By K. L. Myers, R. Espell, C. Deringer

Construction of the AA Pad reclamation was completed in the fall of 2000. Seeding of the ET cover began in the late fall of 2000 and continued through May of 2001. On Saturday afternoon, June 1, 2002, a large, very localized thunderstorm struck the reclaimed AA Pad site. Eyewitnesses present at the time described a dark storm cloud parked above the site for less than half an hour. Average rainfall intensity was measured to be 122 mm (4.8 inches) per hour and peak rainfall intensity was estimated to be 213 mm (8.4 inches) to 259 mm(10.2 inches) per hour. At the time of the storm, the construction was less than two (2) years old and the vegetation had only a single season of growth. The entire period from the end of construction until the date of the storm was a drought period with below normal precipitation. Other than a few small snowmelt events, there was no precipitation event large enough to produce any significant flow in the channel network. Therefore, the very first significant runoff event was the extreme event of June 1, 2002. The storm essentially represents a large-scale field test of the design concepts used at the AA Pad site. Shortly after the storm, data was collected and analyzed with the intent of learning as much as possible about the performance of the cover system design with the expectation that the newly acquired knowledge might be utilized in future designs to further improve the performance of similar cover systems during extreme events.

Jan 1, 2003

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By Richard Switalski, Mark R. Kritzer, Boro J. Lukajic, Robert Pintabona

Ground freezing was chosen as an initial support method during construction of two deep shafts at the Mill Creek project. The Mill Creek, Phase 2 tunnel (MCT-2) is utilized to convey and store combined storm and sanitary sewage collected from the member communities in the greater Cleveland area. The main objective of groundfreezing was to provide a strong support structure to resist soil and groundwater pressures. This was achieved by creating a watertight, frozen-ground barrier around the shaft perimeter. The paper will provide an overview of ground freezing techniques applied during the construction of two shafts, each 250-feet deep.

Jan 1, 2003

By E. W. Geist, W. J. Bronkala

PRINCIPLES OF MAGNETIC SEPARATION The application of magnetic separators relies on the different behavior of individual mineral particles under the influence of magnetic forces. When exposed to a magnetic field, all materials are affected in some way. According to whether materials are attracted or repelled by the magnetic field, they are designated paramagnetic or diamagnetic, respectively. Paramagnetic materials are attracted along lines of magnetic force from points of lower magnetic field intensity to points of higher magnetic field intensity. The very strong response of some materials to a magnetic field is sometimes designated ferromagnetic and the particles attracted frequently retain magnetic properties after the applied magnetic field is removed. Diamagnetic materials are repelled along the lines of magnetic force from points of high magnetic intensity to points of lower field intensity. Only limited commercial use of diamagnetic effects has been made. For practical applications, the paramagnetic groupings are: 1. Strongly magnetic (ferromagnetic) 2. Magnetic 3. Weakly Magnetic 4. Non-magnetic The limits of these groupings are not well defined and will vary in some mineral species. Only a few minerals are ferromagnetic (magnetite is an example) and arbitrarily some investigators have selected 10,000 gauss, or 1 Telsa, as the dividing line between low and high intensity magnetic fields. I. S. Wells has developed a table indicating the magnetic intensity required to separate a selected grouping of minerals which is shown in Table 1 on page 2. A similar table has been developed by Carpco Inc. of Jacksonville, Florida in conjunction with the use of its high tension separators. This table, Table 2 on page 3 shows other minerals grouped in the broader categories cited above. Magnetic separation methods are used either to separate valuable minerals from nonmagnetic waste or magnetic impurities or other valuable magnetic minerals from bulk nonmagnetic values. Magnetically susceptible mineral particles occur as either individually discrete particles,

Jan 1, 1986

By M. F. Corcoran

Rapid advances have been made in the past few years in the application of automatic controls and instrumentation to iron ore pelletizing plants. Present practice in applying instrumentation and control to the Grate-Kiln system of iron ore pelletizing is described. Major control points and loops are tabulated. Future trends in the application of digital control including computer data logging systems are described.

Jan 1, 1965

By Robert A. Bauer

Geology and weather effects produce natural ground movements that may be misinterpreted as mine subsidence. Weather, local geology and vegetation clearly influence the elevation of the ground surface through frost action and changes in groundwater levels and soil moisture content. Common practices of monument and benchmark design and placement do not address the problem of natural ground movements. Monuments can be designed to minimize some natural ground movements. Differential displacements can be reduced by knowledgeable placement of benchmarks and monuments which are of similar design and construction. Commonly, the threshold values of movement for the determination of mine-induced subsidence are dependent on the closure errors (accuracy) of individual surveys. Accuracy is more than the amount of closure error; it should include the range of elevation changes (error band) determined for each monument over a period of time before it is disturbed by mining. Multiple baseline surveys of the entire monitoring system, conducted before the onset of subsidence, should be used to establish subsidence detection limits.

Jan 1, 1986

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By P. M. Krishna

An example illustrates the use of ASTM Standard E901-82, Classification System for Uranium Resources. The example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that ,remain in fixing the classification of a given uranium resource include the uncertainty in estimating the quantity of undiscovered resources and resolving the differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1983

By D. W. Park

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floor and thinly-laminated immediate roof. The investigation covered by this paper concerns a mine that was experiencing ground-control problems with weak floor conditions. Four hundred ft above the presently producing seam, another seam has been mined out. Several roof falls occurred locally, and as much as two ft of floor heaves have been experienced. The paper presents the results of comprehensive analysis conducted on floor heave, roof sagging, and the influence of the mined-out seam using instrumentation and numerical analysis.

Jan 1, 1991

By W. J. Roberds

A formal and explicit yet cost-effective approach is proposed to ensure that decisions made during mine development are optimum (with respect to their ultimate consequences) as well as defensible. This risk management approach is based on probabilistic risk assessment and established decision analysis techniques, and appropriately considers the relationships among various mine development decisions, tradeoffs among consequences, the uncertainty in predicting consequences, and the benefits of flexibility to respond to changed conditions.

Jan 1, 1992

By W. N. Brown

One of the seemingly eternal problems with which we are frequently faced is that of providing adequate and economical warehousing facilities to store large quantities of bulk product. Seasonal consumption, transportation, marketing, and other factors very often dictate extensive product warehousing requirements for an operation geared for steady, year-around production of a material requiring weather protection during storage. Fertilizers such as potash and urea are examples of such products; the consumption of these materials is extremely heavy in the early spring at which time the materials must be placed in the soil, whereas, for obvious operating efficiencies, production is more or less constant for a given operation throughout the year.

Jan 1, 1961

By Thomas A. Earl

Strip mining of coal, and to a lesser extent limestone, gravel and other mineral deposits in the Appalachian region of the eastern United States has left many large and small areas of devastated land where mining predated reclamation requirements. In Pennsylvania alone, there are between 250,000 and 370,000 acres of strip-mined land 1,2/. A higher percentage, and a greater total acreage of land in Pennsylvania is in need of some form of reclamation than any other state, with the neighboring states of Ohio and Nest Virginia also having nearly the same magnitude of mining.2/ Recent legislation governing strip mining of coal proposed royalties to cover reclamation of such presently unusable land. However, in Pennsylvania and other states some progress has already been realized by utilizing abandoned strip mines and gravel pits for waste disposal sites. Given acceptable hydrogeologic settings, such use of these mined areas for landfilling has provided the incentive for ultimately restoring unreclaimed land to beneficial use, at no cost to the general public.

Jan 1, 1975