Search Documents

By Prakash M. . P. E. Donde

1. INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has often taken a leading role in introducing innovative construction technologies to build its transit system. Most recently, Contract Section E-5a, which included Fort Totten Station and Tunnels was constructed utilizing the New Austrian Tunneling Method (NATM) in soft ground. Along with the station and tunnels, two permanent shafts were also constructed in soft ground employing the NATM technique. This project is located within the District of Columbia on the Greenbelt Route. The subject of this paper is to discuss the unique method of construction of these two shafts, and explore the benefits of applying the NATM technique to the construction of deep shafts. The design of the shafts was performed jointly by Jenny Engineering Corporation of Springfield, New Jersey, and Mayreder Consult of Linz, Austria. The designers also provided construction support services and a resident NATM expert at the site during construction. The construction of the project started in April 1988 by a joint venture of Mergentime Corporation and H. T. Construction, a subsidiary of Hochtief Company from Germany. This $48.7 million construction project has been completed. 2. SUBSURFACE CONDITIONS The two NATM shafts are located primarily in Cretaceous-age deposits that are over 100 million years old. These deposits are intermixed and lenticular in nature

Jan 1, 1993

In conjunction with steady increases in production levels, long-wall operators have applied greater quantities of ventilating air to control respirable dust and methane gas. As a result, air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high-velocities, especially during shield advance as dust falls from the shield canopy directly into theair stream. Laboratory tests to simulate dust liberation by shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH in a wind tunnel designed to study dust entrainment in high-velocity airstreams. Dust was introduced into the tunnel to determine dust concentration as it relates to entrainment, dilution, air velocity, and particle adhesion. Airborne dust samples were obtained by iso-kinetic sampling using BGI cyclones to quantify respirable dust concentration at the various air velocities. Laboratory tests were con-ducted at velocities ranging from 2.0 to 10.1 m/s (400 to 2000 fpm),and significant differences in airborne respirable dust levels were measured. This research is being conducted to provide fundamental information on the entrainment characteristics of respirable dust at high air velocities, which will subsequently lead to solutions for shield dust control. A discussion of the test procedures and results are presented.

Jan 1, 2004

By T. Yalcin

It is well recognized that machine type and machine characteristics play vital roles in the successful application of froth flotation in mineral processing. Since the early 1900s, a multitude of machine designs have been and are still being introduced in an attempt to improve flotation efficiency. Machines based on mechanical agitation have been the most dominant in industrial practice. However, in recent years there has been a growing interest in pneumatic flotation units because of their claimed simplicity, low cost, high throughput and good metallurgical performance. This work was carried out to assess the effectiveness of pneumatic flotation on a magnetite ore. The method was applied using a prototype pneumatic flotation device that utilized a suitable nozzle for bubble generation. Important variables of the process were examined and optimized, including the nozzle size, air flow rate and froth thickness. Further tests were conducted to determine the influence of frother dosage and to explore the improvements that could be made on concentrate grade and recovery by cleaning and scavenging. Under the best test conditions, an iron concentrate was obtained with a grade of 66.4% Fe and a recovery of 97.7%. Particularly, the recovery was superior in comparison to that of mechanical flotation. This was attributed to the ability of pneumatic flotation to create and maintain a relatively thick froth layer.

Jan 1, 2002

By R. V. Ramani

Minerals, together with agricultural and forestry products, are the primary source of wealth produced in the United States. Although the production of minerals requires only a small fraction of the state's total land surface, as compared with either agriculture or forestry (Table 1), mining activities generally are much more disruptive to the land surface, and rehabilitation is more complex and costly. The past 10 to 15 years have witnessed a sharp increase in mineral exploration and mining, particularly coal mining, which has brought with it an increase in conflict over land use and an increase in negotiations for purposes of mineral prospecting and mining. The general increase in the production and consumption of coal and the particular increase in the percentage of coal extracted by surface mining methods coupled with a growing nationwide environmental consciousness have created increased public concern and in some cases outrage over mining activities. Although there is ample evidence to indicate that it is possible to plan for and design mining activities in such a way that they are compatible with other activities and can thus be made a part of a sequential land-use plan, there is a general lack of knowledge regarding the importance of mining as the provider of basic and essential raw materials to supply society's constantly expanding and increasing mineral needs. This lack of knowledge extends to such matters as land and mineral rights negotiations, the character of mineral deposits and minerals, mineral economics, and land-use planning.

Jan 1, 1977

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By R. W. Seedsman

Mandalong Mine was originally planned to operate with panel widths of 250 m and a predicted surface subsidence in excess of 3 m. The consent conditions applied by the NSW government on this mine plan were very tight and, following a change in ownership, were considered by the new operator to present a number of unacceptable business risks An acceptable risk profile for the mine layout restricted surface deformations to less than 500 mm vertical subsidence, less than 7 mm/m tilt, and less than 5 mm/m strain. Empirical subsidence prediction methods indicated that it would be necessary to reduce extraction panel widths of 80 m - an uneconomic option. The application of a number of rock mechanics concepts identified that the local overburden geology could be exploited such that panel widths of up to 175 m could be possible. The 125 m width was selected as a low-risk introduction of this new subsidence prediction method. The extraction of the first 2 longwall panels has demonstrated the validity of the prediction subsidence method and has provided the opportunity to refine the selection of key input parameters. The impact of mining through a zone of thrust faults was successfully predicted. The mine is now planning the introduction of 160 m wide panels, and will review the associated subsidence impacts prior to any further increases in width.

Jan 1, 2006

By Gerald G. Griswold, Allan G. Provost

"To Sink or Not to Sink"; this play on the Bard's words sums up the considerations and problems that face the owner on every potential shaft sinking project. The growing demand for access into the earth is pressing construction into new areas and to greater depths. The following discussion will entertain some of the effects of these new and unknown aspects upon the approach to designing and sinking of deep shafts. We will also look at the current shortages of equipment, materials and skilled manpower, and their effect upon the planning and sinking of shafts. Particular emphasis will be placed upon equipment selection, and we will discuss how economics, while always a prime consideration, is now, more than ever, both an incentive and a detriment to the industry. FUTURE CONSIDERATIONS Shaft construction is assuming ever increasing importance both in mining and civil endeavors. The rapid depletion of near surface mineral reserves is requiring the mining industry to look deeper into the earth for new sources. These greater depths increase the exposure to unfavorable geological conditions; heavier ground, high water pressures, and high temperature. South African gold mines have now reached depths of 12, 000 feet, where the rock temperature is 1380 and water bursts from the fissures. In North America depths to 7, 500 feet have been sunk, but deep shafts are still generally considered to be those of

Jan 1, 1974

By Martin N. Kelley

The Great Belt Link is a $3.5 billion fixed link across an 18 km (12 mile) wide body of water that separates the island of Zealand, on which Copenhagen is situated, and the main land mass of Denmark, Jutland, which is part of the European continent. The project consists of three main contracts. The first contract is an 8 km (5 mile) long, two-bore railway tunnel for the eastern half, the second contract is a 6.6 km (4 mile) combination railroad and highway bridge for the western half, and the third contract is a 6.7 km (4 mile) long high-level highway bridge for the eastern half. This paper will discuss the Eastern Railway Tunnel Project and the methods of construction that the joint venture consortium plans to use, along with its equipment selection. The ground conditions to be encountered begin with glacial tills, which are a mixture of clay, silt, sand, gravel, cobbles, and granitic boulders. The boulders can be up to 1-3 m (3-10 ft) in diameter. Underlying the till is a marl which is sometimes highly fractured with hydrostatic pressures of up to 8 bar. About 40% of the tunnel is in till and 40% in marl, with the remaining 20% being a mixed face of the two formations.

Jan 1, 1991

By S. I. Nozhko, V. N. Guliy, A. A. Zolotarev, L. M. Luyshnia

The study of the apatite deposits of the Aldan Shield shows wide spread of the Precambrian apatite-carbonate ores and possibilities of using them for extraction of apatite. Dependency of flotation on ore minerals was studied according to the following scheme: preparation of the monomineralic samples of anhydrite, gypsum, chlorite, serpentine, phlogopite, apatite; mixing them in apatite ore of the average composition; followed by flotation. Another series of the experiments was conducted to ascertain a dependence of flotation activity of the different minerals on the different flotation reagents, which were used as collectors. It has been shown that apatite from silicate-carbonate ores is most extractable because it has the biggest size of grains and is the most free of inclusions. Beneficiation of the sulphate-containing apatite-carbonate rocks is possible when flotol - 7.9 is used as a collector. Meanwhile, the use of the tallaktam leads to an increase in the sulphate recovery. The estimation of individual technological features of the layered Mghydrosilicates and their influence on the process of beneficiation has been examined using samples of apatite-dolomite ore (P205-8%) with the addition of the phlogopite, serpentine and chlorite. The results show that there is little influence of the chlorite presence on the flotation while the serpentine presence leads to a decrease of the flotation, because of its high specific surface area.

Jan 1, 1993

By D. T. Iseley, A. L. Atta-alla

INTRODUCTION The extension project of the East Line Subway of Atlanta's subway network includes the construction of two single track transit tunnels under Interstate Highway 285. The project will be in DeKalb County, Georgia. The length, width, and height of each tunnel are 54.25, 6.3, and 7.2 m (178, 21, and 23 ft) respectively. The ground cover above the tunnel crown ranges from 1.5 to 3.25 m (5 to 11 ft). A soil pillar about 5.5 m (18 ft) wide will remain between the tunnels. The construction of each tunnel includes (i) installation of 21 steel soil support pipes of 75 cm (30 in) diameter, (ii) jet grouting 15 soil cement shafts of 60 cm (24 in) diameter in the soil under the pipes, (iii) contact grouting behind the tunnel lining and between soil support pipes and pavement, (iv) excavation of soil inside the soil support arch, and (v) installation of steel pile foundation, steel sets, and permanent tunnel lining of cast-in-place concrete, all as shown on the cross section in Fig. 1. The soil profile can be described from top to bottom as cement/asphalt concrete pavement, a fill layer consisting mostly of stiff sandy silt/firm silty sand, a residual soil layer consisting mostly of silty sand/sandy silt, partially weathered rock, and solid rock.

Jan 1, 1991

By A. Iordanidis

Ieropigi Fe-Ni deposit is located in northern Greece, in Kastoria?s prefecture near Albania?s borders. A laterite profile exposed by opencast mining and placed near the basement of the mine was chosen for sampling. Ten samples, representing ?pure? Fe-Ni ore, ophiolite-bedrock, ?red? ophiolite and ?enriched? ophiolite were collected, based on macroscopic observation. The samples were analysed by X-Ray powder Diffraction (XRD) for the determination of the mineral phases. Iron and Nickel concentrations of the same samples were also determined by X-Ray Fluorescence (XRF) methodology. The Fe-Ni ore samples consists predomi-nantly of hematite, goethite, chrysotile (serpentine), saponite and quartz. ?Red? ophiolite samples consists mainly of chrysotile, hematite, quartz, calcite and small amounts of paragonite and goethite. Bedrock and ?enriched ophiolite samples are comprised of chrysotile, hematite, calcite, quartz, nontronite, paragonite and sepiolite. The Fe content ranges between 13% and 49% in Fe-Ni ore samples and between 7% and 10% in ophiolite samples. The Ni content ranges between 1% and 3% in Fe-Ni ore samples and between 0.3% and 4.5% in ophiolite samples (the higher content is observed in the so-called ?enriched? ophiolite). A correlation between Fe-Ni concentrations and mineral assemblages is being attempted in order to evaluate the nickel-rich mineral phases. It is shown that the nickeliferous minerals are serpentine, hematite, goethite and saponite.

Jan 1, 2006

By William R. Nash

The scope of work for the fast track construction of the Weeks Island Replacement Facility, Weeks Island, Louisiana included the design and construction of two salt mines. Mine #1 - An interim underground mining level consisting of a 975 m (3200 ft) incline and 3520 m of 5.5 m x 7.3 m (11560 ft of 18 ft x 24 ft) drill and blast excavation; raise boring; core drilling; roadheader excavation; complete bulk material handling facilities utilizing an existing production shaft. Mine #2 - Simultaneous with the interim mine construction a new one million ton per year underground salt mine was constructed consisting of: two 5.5 m diameter x 381 m (18 ft diameter x 1250 ft) deep shafts; 76450 cu m (100,000 cu yd) of drill and blast bottom excavation; surface and undergound bulk material handling systems (conveyors, skip loaders, shaft equipment, hoisting); ground freezing for water control for both the production and service shafts; the design of the first underground doublewall slipform installation of a dynamic bitumen shaft lining system; the emergency grouting of both the existing production shaft and the interim mining level in the salt dome; 227 mt x 64 m (250 ton x 210 ft) high structural steel production headframe; 2.2 MW (3000 hp) double drum mine hoist; service shaft headframe; and service buildings.

Jan 1, 1987

By Louis M. Schlesinger, Joel F. Hutwelker

A pilot plant was constructed to attrition scrub and deslime North Carolina phosphate ore. A 15.2 cm (6 in.) diameter pilot-scale Linatex Hydrosizer was used for desliming. Four tests were run at a throughput of 2.9 t/hr/m2 (0.30 ton/hr/f t2) and a teeter bed density of 1.12-1.13 g/cm3. The teeter water flow rate was varied to create an upflow velocity ranging from 0.25-0.47 cm/s. (This latter value is equal to the terminal settling velocity of a 200 mesh (74 micron) particle having a density of 2.7 g/cm3.) The recovery of +200 mesh oversize to the sizer underflow was 95%-96%, regardless of the teeter flow rate. The recovery of -200 mesh undersize to the sizer overflow increased from about 90% at 0.25 cm/sec to 100% at 0.47 cm/sec. A metallurgical balance that was conducted for one of the tests showed that less than 2% of the phosphatic value was lost to the overflow. A fifth test was run using an upflow velocity of 0.47 cm/sec; however, the teeter bed density was maintained at 1.05 cm/sec. This change had the effect of reducing the cut point (d50), while maintaining complete slime removal.

Jan 1, 1993

By B. K. Parekh

The International Symposium on Comminution was organized at Camborne School of Mines, Cornwall England. Papers covered the fundamental and practical aspects of comminution in the mineral industry. Although comminution equipment design has not changed fundamentally during the last 50 years, methods of control and optimization have improved considerably. A simulation model for batch ball milling in the rotating mill was developed as a step toward continuous simulation of ball and autogenous milling. New concepts in jaw crusher technology design and the concept of a 1.6- x 2.1-m (66- x 84- in) jaw crusher with open feed throat has resulted in power savings. The use of cone crusher technology in comminution circuits with particular reference to machine design, plant flowsheet and control figuration has been reported by Boliden Allis, of Sweden. The Whiten steady state crusher model form has been used to develop a quantitative model of 2.1-m (7-ft) cone crushers. This was done by incorporating liner age (wear) and liner length as variables on the selection of particles for breakage and thus on the product size distribution. Another paper by Lira and Karetsky discussed the development of a model based on a multisegment ball mill developed by Whiten and Kavetsky. It is capable of simulating the performance of a coarse grinding ball mill of a given diameter, ball size and mill speed.

Jan 1, 1991

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By J. A. Dos Santos

High angle conveyor (HAC®) systems in open pit mining offer many advantages over the traditional, truck only, haulage systems, including: (1) superior energy efficiency, (2) less dependency on petroleum products, (3) less sensitivity to inflation, (4) less labor, (5) less excavation for the amount of ore recovered, and (6) less ramp construction and maintenance costs. Previous studies had revealed the technical and economic feasibility of high angle conveyors. This paper presents the Sandwich Belt HAC® as the vital link to optimization of in-pit conveying systems. HAC development to date is discussed, beginning with studies in 1979, to the first large scale prototype in 1983, to the first commercial unit in 1984, into "the latest commercial installations. Discussion continues with the HAC systems to suit the various open pit mining operations and the corresponding characteristics of the system components, particularly the high angle conveyor. The range of HAC systems from the low capacity (up to 1,814 t/h), low lift (10.7 to 36.6M), highly mobile to the moderate capacity (1,814 to 3,629 t/h), moderate lift (36.6 to 76.2M), intermittently mobile to the high capacity (greater than 3,629 t/h), high lift (greater than 76.2M), semi-mobile, are discussed along with some possible combinations of these.

Jan 1, 1989

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic's rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

By Ralph E. Magnuson

The quality of our environment is of great importance to all of us. Today, there is a great public concern about the degradation of our air, land, and water and the resultant slow death of our planet Earth. The miner has always been concerned with his environment. Historically, mining has been a part of the frontier. As a result, the miner has pioneered and developed many parts of the world. In the beginning, he had to hack out a place for his mine, himself, and his family. He was given accolades and praise for his accomplishments. Now, however, he is attacked as a ravager of the landscape. It was and is no different on the Marquette Iron Range in Marquette County, located in the Upper Peninsula of Michigan. Iron ore was discovered in 1845 and mining was begun by 1848. Over nearly 1 ¼ centuries, a total of 379,197,000 tons have been shipped to market. Ports, docks, railroads, and towns all had to be built in order to get that tonnage out to iron and steel makers. In those early days the environment had to be mastered, not pampered.

Jan 1, 1970

By S. C. Carniglia

Bayer-process alumina hydrate becomes in turn the source of a host of special products in addition to the calcines that feed aluminum reduction cells. Though relatively smaller in tonnage, specialty aluminas serve important industrial markets in an exciting and growing variety. Production methods and applications are discussed for: (1) trihydrate as flame retardant in organic materials; (2) high-surface-area transition aluminas as desiccants and scavengers, catalysts and substrates; (3) calcines for industrial ceramics, refractories, and abrasives; and (4) tabular alumina for refractories, bed supports and other uses.

Jan 1, 1977

By Elif Çevik

This study deals with the mineralogical-geochemical characteristics and the industrial usage of the olivine from the dunites that crop out on the west of the Topuk village (Orhaneli). Mineralogical compositions of non-altered dunite samples are averagely as: Olivine (>90%), serpentine (1-4 %), opaque minerals especially chromite, magnetite, pyrite (1-3 %), and secondary minerals as magnesite, chlorite (1-2 %). X-Ray Diffractograms of the dunite samples indicate that olivines are in forsterite (93 on an average) composition, and chlinochrysotile and lizardite accompany to the forsterite. Chemical analyses of the dunites show that MgO, SiO2, Fe-,03 and LOI contents vary from 40,99 to 50,2 %, 34,67 to 40,6 %, 6,8 tol3,7 %, 0,11 to 11,27 %, respectively. SE-TAT Mining Company states that the study area has 400.000.000 tonnes proved, 800.000.000 tonnes probable and totally 1.200.000.000 tonnes olivine reserve. Consequently, all studies indicate that Orhaneli Olivin has convenient mineralogical and chemical properties and the grain size (0.04-40 mm) for industrial usages such as abrasive, olivine sand products, steel slag conditioner, balast and covering material in industry: Orhaneli olivines are demanded especially from the firms related to refractory industry, iron-steel factories, naval forces and shipyards. SE-TAT Mining Company also exports these olivines to different countries such as Macedonian and Spain.

Jan 1, 2005