Search Documents

By M. C. Manderson

Phosphate rock is a naturally occurring mineral which, in upgraded form, is important to both agriculture and industry. Phosphate rock normally must be upgraded before it can be assimilated and used. Most of this upgrading is now carried out by chemical means, largely through the reaction of a strong inorganic acid (primarily sulfuric acid) with the phosphate rock to remove major impurities and to produce soluble phosphate. A less important but yet still commercially significant conversion method involves the thermal reduction of phosphate rock at high temperature in an electric furnace to produce elemental phosphorus. The elemental phosphorus is then converted to usable end products. This conversion route is a more costly method than the chemical route, but it has the advantage of being able to produce chemically pure phosphorus derivatives. On the other hand, the use of phosphate rock for agricultural application-primarily for use as a plant nutrient ingredient for fertilizer -does not require the same level of purity. As a consequence, the chemical method of phosphate rock upgrading is the predominant technique for producing phosphatic fertilizers.

Jan 1, 1977

By Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides: chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 1000 to 150°C. The rate of dissolution of chalcopyrite becomes so rapid under these conditions that the rate of recovery is no longer limited by the rate of chalcopyrite dissolution, but by the degree of exposure and other factors. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, size of sulfide particles, and fraction of sulfide exposed to solution.

Jan 1, 1972

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Mobile RAs have a limited ability to dissipate heat, and heat buildup can lead to a life-threatening condition as the RA internal air temperature and relative humidity increase. The National Institute for Occupational Safety and Health Office of Mine Safety and Health Research performed heat testing on a 10-person tent-type training RA and contracted ThermoAnalytics, Inc. to develop a validated thermal simulation model (TSM) of the tested RA. The TSM was used to examine the effects of the constant mine strata temperature assumption, initial mine air temperature (MAT), initial mine strata surface temperature (MSST), initial mine strata temperature at depth (MSTD), and mine strata thermal behavior on RA internal air temperature using 117 W of sensible heat input per simulated miner. For the studied RA, when the mine strata temperature was treated as a constant, the final predicted RA internal air temperature was 12.8°F lower than it was when the mine strata thermal behavior was included in the model. A 10°F increase in the initial MSST resulted in a 7.1°F increase in the final RA internal air temperature, whereas a 10°F increase in the initial MSTD yielded a 2.5°F increase in the final RA internal air temperature. INTRODUCTION Since 2008, the Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (1). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. NIOSH recommended an apparent temperature limit of 95°F in its 2007 report to Congress (2). In 30 CFR 7.504, MSHA has specified a maximum apparent temperature of 95°F inside an occupied RA (3). The apparent temperature is calculated using both air temperature and relative humidity (4). Calculations could be used to determine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, in order to simplify the problem, the mine temperature could be assumed to remain constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. OMSHR research has shown that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (5). Thus, calculations performed with the assumption that the mine temperature is constant would under-predict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, research has not been used to confirm that the mine air temperature is the appropriate basis."

Jan 1, 2016

Water contact angles in the air/water/francolite, fuel oil/water/francolite and fuel oil/water/quartz systems were measured to describe the wetting characteristics of these minerals. It was found that white francolite is more hydrophilic than black and tan francolite both in the absence and presence of fatty acid addition. The contact angle measurement results do not correlate very well with the flotation response and it appears that kinetic aspects of the bubble attachment process play an important role in the francolite-fatty acid flotation system.

Jan 1, 1997

By D. P. Caplice

On behalf of the Ontario Water Resources Commission, I would like to express my sincere appreciation to your Institute for presenting us with this opportunity to outline the regulatory control programme as it relates to the mining industry in the Province of Ontario. In Canada, and particularly in Ontario, we are blessed with an abundance of natural resources. Fresh water in the form of lakes and rivers covers nearly 17 per cent of the area of the Province. (Total area of the Province of Ontario is 412,582 square miles.) The mining industry, which had its beginning in the early 1800's with a small iron ore plant, has progressed with the major discoveries of nickel and copper in 1883, silver in 1903, gold in 1908, iron in 1939 and uranium in 1953, to the point where, in 1966, almost one billion dollars in mineral wealth was mined in Ontario. Water, in spite of its great abundance and with due respects that it may become a natural resource worthy of export in the foreseeable future, has become increasingly precious in Ontario, particularly in the more urban areas in the southern part of the Province.

Jan 1, 1968

By K. Lapakko

One responsibility of the Minnesota Department of Natural Resources is to encourage the development of mineral resources within the state. A second responsibility is to ensure that mineral development does not adversely impact other natural resources, including the water resources of the state. One approach the Division of Minerals has taken to fulfill these responsibilities is to conduct cooperative research with the mining industry. To encourage mineral development the Division has cooperated with industry on projects related to exploration, mining, and mineral processing. To examine environmental issues the Division has worked in concert with iron ore, base metal, and precious metal exploration and mining companies, as well as the Western Governors' Association, US Bureau of Mines, US Bureau of Land Management, and the US EPA for the past 20 years. These projects were conducted to evaluate methods of predicting, preventing, controlling, and treating problematic mine waste drainages, as well as mine waste revegetation. This paper I) briefly summarizes cooperative projects conducted, 2) enumerates elements which have contributed to the success of cooperative projects, and 3) describes changes implemented for future projects at the Division's new field and laboratory research facilities, as well as at existing mine and plant sites.

Jan 1, 1998

By E. O. Strahl

In the search for economic mineral deposits, the need for efficient mineral or chemical assays is of prime importance. Costly analytical methods and long delays in obtaining assay results severely limit the effectiveness of an exploration program. The assay problem becomes acute once a potential ore body is located and large numbers of samples are generated in close interval drilling programs. In order to avoid the delays and high costs of extensive assays, the exploration geologist or mining engineer is likely to be required to curtail his drilling program, composite samples, or restrict the required analyses to a limited number of critical elements. As a result, the definition of the potential ore body may be less than needed for final economic evaluation. The assay requirements for bauxite exploration usually involve a considerable number of total elemental and empirical analysis. Since the Bayer process for extracting alumina from bauxite involves the selective dissolution and reaction of specific minerals from the bauxite, a direct chemical analysis for elemental composition yields only a portion of the data required to effectively describe the potential economic value of ore body or deposit. To fully characterize the economic value of a bauxite requires digestion, mud separation and mud settling tests under conditions approximating a commercial Bayer plant. A close approximation of the process behavior of a bauxite also can be calculated from a combination of the chemical and mineralogical analyses. By determining the elemental chemistry, mineralogy, and Bayer plant processing characteristics of a few samples of a given bauxite, correlations can be derived that permit defining a bauxite in terms of a given set of process conditions.

Jan 1, 1977

By Thomas Pea, Heiner Kontrus, Jérôme Steinkühler

In tunnel condition assessment, the trend is towards comprehensive 3D measurement combined with high quality image texture to document and quantify damages to the tunnel surface and to create a cohesive data base of the structural conditions throughout its lifespan. The faster such measurements can be made on site, the less it impacts traffic conditions of the highly sophisticated subway systems. The Dibit high-speed 3D scanning system which is based on Photogrammetry and LiDAR technology enables data acquisition in tunnels at a speed of up to 60 mph. Given the high rate of speed the system can operate, tunnel shutdowns can be drastically reduced, and tunnel safety increased. The photorealistic texturing of the 3D-model allows the identification and analysis of smallest material damage (e.g., cracks ≥0.3 mm wide). The publication illustrates technical details and 3D results of the innovative system from measurements that were performed in the subway tunnels of the Bay Area Rapid Transit System in San Francisco, CA (total length 66.23 km).

Jun 13, 2021

By Karl V. Lindell

Asbestos is not the name of a distinct mineral species, but rather the commercial term applied to the fibrous form of several minerals differing widely in composition. There are some 30 known varieties of asbestos but of this number only 6 are of economic importance, and these, in order of economic significance are chrysotile, crocidolite (or blue asbestos), amosite, anthophyllite, actinolite and tremolite. Chrysotile asbestos was formed by the introduction of hydrothermal solutions into fractures in serpentinised ultrabasic host rocks. These solutions dissolved magnesium silicate from the wall rocks, and with subsequent lower temperature and pressure they became supersaturated, and crystals of chrysotile asbestos formed. The chemical composition is variable but is classified as a hydrous magnesium silicate, containing a high percentage of magnesia and water, plus varying amounts of alumina and ferrous and ferric iron. Other asbestos minerals are formed by a similar process but with a different host rock e.g. crocidolite occurs only in iron' formation. The chemical composition of asbestos minerals other than chrysotile, shows a wide variation, but in general may be classified as silicates, or metasilicates, containing varying amounts of calcium, magnesium, sodium and iron.

Jan 1, 1964

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By Robert W. Row

Advanced physical coal cleaning processes that are now under development may remove significantly greater fractions of pyritic sulfur and ash than do commercial coal cleaning processes at comparable heating value recoveries. These processes may be useful for reducing sulfur dioxide emissions from electric utilities and other emission sources. However, little work has been done to determine their applicability to any major coal market. The northeastern states of the United States are interested in burning more coal, but with further sulfur dioxide emission restrictions. Their nearest coal sources are relatively high sulfur Northern Appalachian coals. The project discussed in this paper, which is scheduled to be completed in June 1985, has the objective of technically and economically evaluating various coal supply scenarios involving five selected advanced physical coal cleaning processes; and comparing the economics of them with alternative fuel supply options open to the northeastern users.

Jan 1, 1985

By M. L. Free, N. Dhawan, M. S. Safarzadeh, J. D. Miller, M. S. Moats

"The drum agglomeration of nickel laterite and gold ores has been optimized through the design of experiments (DOE) using a Taguchi L16 (45) orthogonal array to determine the optimum conditions for maximizing average agglomerate size and minimizing the amount of fines. The effects of controllable operating factors including moisture content (nickel laterite ore: 34-37%; gold ore: 7-10%), retention time (2-3.5 min), drum speed (15-45% critical speed), drum load (nickel laterite ore: 8-32 %; gold ore: 6-22%) and acid concentration (150-600 g/L) on the performance of the agglomeration process were studied.For nickel laterite ore, maximum average agglomerate size and minimum percent fines (-1 mm) occurred under the following conditions: drum load (23.7%), moisture (36.5%), time (3 min), drum speed (30% critical speed) and acid concentration (150 g/L). Under the studied nickel laterite ore conditions, the most effective parameters for maximizing average agglomerate size and minimizing the amount of fines were found to be drum load and acid concentration, respectively. Drum speed had a statistically significant effect on minimizing the amount of fines. Maximum average agglomerate size and minimum percent fines (-1 mm) for gold ore occurred under the following conditions: drum load (19.3%), moisture (8.5%), time (2 min 15 s) and drum speed (40% critical). The most significant factors for maximizing average agglomerate size and minimizing the amount of fines for gold ore were found to be drum load, time and moisture.IntroductionSeveral heap leach operations have experienced problems in terms of poor recovery due to percolation issues caused by low-grade complex ores, tailings and clayey deposits. Poor percolation can lead to low metal extraction due to solution channeling or the development of impermeable/dead zones within the heap (Dhawan et al., 2012; Kappes, 2005). Improper heap building practices such as the use of loose agglomerates and inadequate attention toward the presence of clay minerals have been among the main reasons for percolation issues. During the transport of ore material, severe segregation of the material can occur. To overcome percolation problems, a major improvement was made through the introduction of agglomeration prior to ore placement. If the ore particles and agglomerates are of similar size, segregation can be avoided to a great extent (Dhawan et al., 2013; Kinard and Schweizer, 1987; McClelland and van Zyl, 1988). Agglomeration improves the uniform percolation of solution through ore heaps and is applicable to many ores, wastes and milled tailings (Bouffard, 2005; Dhawan et al., 2013). Manning and Kappes (2005) reported agglomeration/ stacking accounts for ~14% of the total heap leaching operating cost. The cost of binder is a primary contributor toward the total cost. Also, the lack of consistent quality control tests for agglomerate often leads to operational problems. The details are mentioned elsewhere (Dhawan et al., 2013). Considering the significant contribution of the agglomeration/stacking step toward the total heap leach operating cost, it is appropriate to study the agglomeration behavior and its optimization for two different ores. The reason to study the same parameters for different ores is the fact that significant variability in the agglomeration behavior of different ores has been reported to exist in industrial operations."

Jan 1, 2015

By Irwan Halim, Seung Han Kim

This paper will describe design of precast segmental tunnel lining for the Pawtucket CSO Tunnel Project in Providence, Rhode Island. The tunnel is 11,700 LF long with 30-foot finished diameter to be constructed in complex sedimentary rocks. Special features of the segments include a large keystone and no connector used on radial joints. The typical segments will be steel fiber reinforced, and hybrid segments with additional steel rebars and shear bicones will be used around the adit openings without use of any structural framing. The important design considerations will be discussed, including special 3D segment to adit connection analyses performed.

Dec 1, 2022

By Paul H. Johnson

A field investigation was undertaken to study some of the. chemical and hydrological aspects of leaching an impermeable copper sulfide waste dump. Samples, obtained by means of a Becker pneumatic drill from Kennecott's Chino "J" dump, near Silver City, New Mexico, were analyzed for their moisture and soluble-salt content, Fe +2 , Fe +3, Cu +2 , and H in their interstitial solutions and non-water - soluble Fe, Cu, and S in their rinsed residues. Conclusions were drawn from these data concerning the overall chemistry of impermeable-dump leaching and the hydrological characteristics of the dump.

Jan 1, 1970

By J. L. Francke

This paper describes the practices and methods used in a study of Time Domain Reflectometry (TDR) as an inexpensive deformation monitoring tool in underground excavations at the Waste Isolation Pilot Plant (WIPP). The WIPP is being developed near Carlsbad, New Mexico, for the disposal of transuranic nuclear wastes in bedded salt 655 m (2 150 ft) below the surface. Data collected from WIPP geomechanical monitoring are used to characterize conditions, confirm design assumptions, and understand and predict the performance of the deep salt excavation. The geomechanical monitoring program encompasses numerous geomechanical monitoring techniques ranging from inspection of observation boreholes to advanced radar surveys. In 1989 TDR was introduced as a monitoring tool with the installation of 12.7 mm (0.5 in) diameter TDR cables in the underground excavations. In 1993, a new TDR system was installed in a separate location. Based on experience with the previous installation, enhancements were implemented into the new TDR system that: 1.) extended the period of performance by increasing cable diameter to 22.2 mm (0.875 in), 2.) increased accuracy in locating areas of deformation by aligning cables with nearby observation boreholes, and 3.) improved data acquisition and analyses using a standard laptop computer, eliminating the chart recorder previously used. In summary, the results of a correlation between the TDR signatures to nearby observation boreholes and geomechanical instrumentation will be presented.

Jan 1, 1996

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By A. A. Campoli

A stress control design strategy was developed to minimize the explosive failure of highly stressed pillars, during room-and-pillar retreat mining conducted between stiff immediate roof-and-floor strata. A confined core coal pillar strength model was based on in-mine geotechnical evaluations of successful room-and-pillar and longwall bump control designs. Tributary area and linear shear angle approaches were used to estimate development and gob side abutment pillar loads for supercritical section widths. Subcritical width sections separated by barrier pillars to control stress within total extraction panels were optimized with the boundary element program MULSIM/NL.

Jan 1, 1994

By Malcolm J. Robinson

Over 80% of Australia's population lives within 200 km of the coast, 70% in 10 major coastal cities. Potential cement raw materials are widely distributed but deposit size, quality, transport, market and environmental considerations are important in determining economic value. Major production locations are in a variety of geological environments ranging from Lower Paleozoic crystalline limestones to Tertiary and Recent polyzoal limestones and limesands, both onshore and offshore. Raw material transportation is by road, rail, sea, aerial ropeway and pipeline; road/rail transportation of the finished product is traditional but movement by sea of clinker and cement is increasingly a feature of the industry.

Jan 1, 1982

By Alex Stewart

Most iron bearing ores treated by the R=N Direct Reduction Process yield products lower in phosphorus than the initial ores. The sulfur is also removed and generally is in the range of 0.02 to 0.05 percent in the final R=N product, independent of the sulfur content of both the ore and carbon fuel used. The mechanism and thermodynamic justification of the principal reactions leading to the removal of both phosphorus and sulfur and the control of sulfur in the iron concentrate produced are discussed and supported by the results of laboratory experiments. In substantially all iron ores (containing up to 4% sulfur as sulfate) and solid carbon fuels (containing sulfur from 1 to 8%) tested, the rejection of sulfur has been in the order of 90-95%, with not more than 0.02 0.05% sulfur in the final metallic iron product. With respect to phosphorus-bearing iron ores ranging up to 0.70% P205, the rejection to tailings has been in the order of 70-95%, resulting in not more than 0.03 - 0.07% phosphorus in the final product.

Jan 1, 1958

By Frederick W. Bauer

The potential worldwide "market" for metallurgical bauxite is about 94 million MT. The high degree of concentration of the alumina sector, combined with the high percentage of long-term contractual relationships, results in a small spot market with an illdefined price structure. Further segmentation occurs based on bauxite quality and alumina plant design. The potential 'free" market is estimated to be about 18 million MT that represent the requirements of nonintegrated alumina producers. It, too, is covered almost entirely by multi-year supply contracts.

Jan 1, 1984