Search Documents

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By Joseph Renk, David Akers, Glenn Shirey

Each year, US coal cleaning plants landfill or impound millions of tons of high-quality, fine-sized coal. This coal is not only difficult and expensive to capture during cleaning, but, if captured, can pose serious materials handling problems. The GranuFlow. Technology was developed and patented by the U.S. Department of Energy (DOE) to address these problems. GranuFlow involves the addition of a coal binding agent such as an asphalt or heavy oil emulsion to coal to reduce moisture, dusting, and freezing and to improve the flow properties of the coal in bins and chutes (1, 2, and 3). When the emulsion is added before mechanical dewatering, the binding agent causes the formation of fine-sized coal agglomerates that dewater better than untreated coal. In addition, the binding agent increases the capture of ultra-fine coal in screen-bowl centrifuges. Previous work by DOE has also demonstrated that such treatment results in a significant reduction in dustiness and a reduced potential to freeze. To address concerns about the handling and combustion characteristics of GranuFlow treated coal, DOE performed a pilot-scale pulverization and combustion test (4). No problems were encountered during pulverization or combustion, and use of this fuel in a p.c. boiler was found to be feasible from a technical perspective. CQ Inc. has an exclusive license from DOE to market this technology and is currently performing a series of commercial demonstrations to determine if GranuFlow is both technically and economically viable.

Jan 1, 2005

By William J. Shampine

The Floridan aquifer, which underlies all of Florida, yields water with a sulfate content of less than 50 parts per million in the north-western part and throughout most of the center of the State. In the southern part of Florida and along the most of the east coast, the sulfate concentration generally exceeds 100 parts per million and is as much as 1,700 parts per million. The sulfate concentration tends to be higher in the deeper zones of the aquifer. This map shows the sulfate concentration in the upper part of the aquifer. Sulfate is found in almost all natural water. Sulfate in rainwater is dissolved from impurities and gases in the atmosphere. Rankama and Sahama (1955, p. 314) report that the average sulfate content of rainwater is two parts per million; however, concentrations have been as high as 283 parts per million. Much of the sulfate in rainwater comes from hydrogen sulfide gas which is generated in shallow water on the continental shelves. The combustion of bituminous coal used for heating and industrial purposes seems to be an important local source of sulfate.

Jan 1, 1966

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By Guy T. McBride

Mr. Chairman, Fellow Keynoters, Ladies, and Gentlemen: It is purposed to consider the theme of this meeting, "The 1970's - Pivotal Decade for the Mineral Industries," from the particular -- some would say peculiar -- point of view of one engaged in mineral engineering education, and this coign of vantage prompts the textbookish subtitle, "Problems and Solutions (?) in Undergraduate Mineral Engineering Education." Three interrelated problems, or problem areas, will be presented and discussed, and where solutions seem to be emerging or seem worthy to be suggested, they will be identified. The three problems are: 1. The goals, and therefore the course requirements, of the undergraduate curricula are in question, 2. The unit costs of undergraduate education appear excessive to those who bear the charges, and 3. The social ambience of the day affects for the worse the work attitudes and the career motivation of both prospective and in-course students. The Need. - Any discussion of these problems must bottom upon recognized national needs for minerals and a technologically sound minerals industry staffed by competent engineers, particularly at the exploration, development, and production levels, Fortunately, these needs have been recognized and to some extent quantified, and they are even now under further intensive study by some of the most competent members of our society and profession. The latter reference is, of course, to the current work of the National Commission on Materials Policy (U.S.A.) under the executive directorship of Dr. James Boyd. Predating this, and perhaps to some extent

Jan 1, 1972

By J. S. Spivey

We in the coal industry, especially in the State of Illinois, put tremendous emphasis, including time, money and effort, into on-the-job training. The results of such training and safety have been tremendous. For example, in 1981 Illinois was the first major coal producing state in the history of coal mining to have zero mine-related fatalities. And in 1985, I am very proud to say, we had the second best record in the history of coal mining, with only two fatalities. Obviously, one fatality is one too many. Our goal is, has been and will continue to be to strive for excellence. It is sad, however, that in 1981 while were were celebrating zero fatalities in the workplace, there were 21 fatalities that occurred off the job. Thus, it has become a classic American story. Success with safety has been found in the workplace, but training and preparation to prevent accidents away from the job site have almost been ignored. Accidents are the leading causes of death in the United States for all persons age 1 thru 38, and are the fourth leading cause of death for people of all ages. Every single day, on the average, more than 290 Americans are killed in accidents - a rate of one every five minutes. The leading cause of fatal accidents in the U.S. is motor vehicles. And the number two cause is home accidents. A staggering statistic is that people are being killed off the job at a rate of about 9 to 1 over those on the job.

Jan 1, 1986

By H. J. Sandri

In the spring of 1991, Western Aggregates, Inc. began operating the newest expanded shale lightweight aggregate operation in North America. The operation is located in Jefferson County, Colorado, just south of Boulder, at the sight of the former Ideal Basic Industries ("Idealite") lightweight aggregate plant, which was decommissioned in 1975. The "new" facility has been built to principally serve the Denver and Front Range markets, as well as ship products into other locations in Colorado, Wyoming, New Mexico, Kansas and Nebraska. Western Aggregates is a wholly-owned subsidiary of Inco U.S., a subsidiary of Inco Limited of Toronto, Canada. Inco Limited is the free world's largest producer of nickel and is a leading producer of copper, cobalt, gold, silver, and platinum group metals, high nickel and super alloys, and specialized engineered products. Inco is constantly seeking new mining related investments that leverage off its mining and processing skills and that meet corporate fmancial objectives. Construction materials are an area presently being pursued by Inco. The basic 'building blocks' of society, from a construction perspective, are sand and gravel, stone, and aggregates. To the vast majority of people these are natural products that are mined, quarried or dredged, and other than washing, screening and crushing, are generally used in their primary form. While these materials vary from quartzite river rock, to calcified limestone, to hard basalt, they are generally classified as "heavy" aggregates. There are, however, other types of aggregates that do not fall under the "heavy" classification, but are used in general construction activities just the same.

Jan 1, 1992

By Mortimer J. Richardson

Dredging can be traced to early times where it may have been derived by the Phoenicians prior to the 4th century B.C. The first tangible design drawings of a bucket ladder (BL) dredge can be found in the collections of Leonardo da Vinci (1452-1519), which he produced when he was attempting to create better methods of channel and port dredging. The perfection of the system did not commence until after the invention of the steam engine in the early 1800's; providing the impetus to progress from man-powered mud mills, horse drawn along polders or dikes in the Netherlands, England, France and Germany, to steam-driven. In the 1860's following the various gold rushes in the U.S., Australia, New Zealand, Siberia and South America, with placers in particular, efforts were begun to apply mechanization to achieve deeper digging. There is a recording of a dredge being installed to mine gold in Montana in the 1860's but did not include a processing system. Then in the 1880's in New Zealand, some practical engineers developed a system that is said to be the first bucket ladder mining (BL/M) dredge for mining gold placers. In studies of the New Zealand gold dredging experience, it is estimated that some 500 dredges were built to mine gold between the 1880's and 1942. A careful analysis of the data, however, shows that very few were profitable. The technology appeared to stagnate in the early part of the century. Two of the BL/M dredge design engineers left New

Jan 1, 1992

By David Rolley

The extended weakness of dollar-denominated commodity prices during the past four years has often been attributed to, among other factors, the strong rise in the value of the dollar, and many U. S. producers have hoped for a recovery in metals and minerals prices once the dollar weakened in foreign exchange markets. The recent turnaround in dollar strength may put this view to the test quite soon. Hence a review of the role of exchange rate changes in the determination of the prices of world-traded metals and minerals may be timely. This paper has three parts. Part I reviews the recent summary record of price movements in commodity and foreign exchange markets. Part 11 reviews the distinct ways in which exchange rate changes influence the supply and demand sides of a representative commodity market. Part III then more closely examines copper and aluminum prices to highlight the potential differences in the effects of exchange rate changes for commodities whose production is dominated by geology and commodities which are processing-dominated. The paper also contemplates the likely implications of these differences for commodity prices in the case of a decline in the trade-weighted dollar. The evidence suggests that the degree of recovery for dollar- measured commodity prices may be very different for differing goods. And it may be the case that some commodities whose prices appear to have been most affected by exchange rate influences may show the least recovery in response to a fall in the trade- weighted dollar.

Jan 1, 1986

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Jan D. Miller, Chen‑Luh Lin

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of cm size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of mm size. Based on Micro-XCT, it was expected that 85% of the copper for sample A could be recovered at 65% of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual energy (DE) X-ray radiography was used as a basis for sorting. Previous DE X-ray radiography of a drill core sample demonstrated that this rapid detection method can be used to identify rich or poor Cu-bearing coarse particles. Pilot scale X-ray sorting of sample A (10 × 1 cm) showed 31% rejection of a 0.08% Cu gangue product with a corresponding recovery of 90% copper.

Nov 30, 2021

By H. Verakis

A fire in a coal mine conveyor belt entry represent a major safety and health risk to miners. Fighting belt entry fires can be a commanding effort. If there is a failure of one aspect in the fire fighting needs such as a dissimilar hose-valve connection, then it can result in the inability to extinguish a fire. Fire incident data compiled over nearly 30 years for underground coal mines shows that fires in belt entries account for 15-20 percent of the total number of fires. Fires in the belt entries of coal mines have resulted in injuries and fatalities. New regulations have been promulgated that require an unplanned fire not extinguished within 10 minutes of discovery to be reported to the Mine Safety and Health Administration (MSHA). A fire that is not extinguished within several minutes may take hours or days to extinguish or may require sealing a section or the mine in some cases. The current fire protection regulations in the U.S. Code of Federal Regulations (CFR), Title 30, Part 75 are designed to prevent or control the fire hazards present in a belt entry. These requirements and other factors affecting belt entry fires are discussed, including fire detection and warning, fire suppression devices, type and location of fire fighting equipment, waterlines, and cleanup and removal of combustible materials. The fire suppression systems used to extinguish/control a belt fire and the effect of ventilation on the propagation of conveyor belt fires are also discussed.

Jan 1, 2009

By Julian Brown, Steve Hicks, Zach Agioutantis, Zachary Wedding

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

Although grinding mill liner life has been the subject of extensive studies, evaluation of the effect of liner design on power consumption, a far more significant part of total grinding costs, has been less comprehensive. The factors that effect ball mill energy efficiency are reviewed, and attention is then focused on the mechanisms of grinding. The trajectory of the outer row of balls, with different lifting face angles, is derived, and basic recommendations for mill speed and liner configuration are presented.

Jan 1, 1981

By S. J. Parkin, P. Shead

Extraction of coal at Harworth Colliery is undertaken in the Deep Soft seam at roughly 1000m depth where the strata temperature is 42 "C. Production employs the longwall retreating method using high powered mechanised methods to extract coal at a rate of approximately 40,000 tonnes per week from a single face. This paper describes the climatic conditions encountered on a typical district , 6's district, where the initial ventilation set-up was as a typical U-type district which was antitropally ventilated. Under this initial set-up climatic conditions in the intake typically exceeded 30 "C effective whilst in the face area and in the return airway effective temperatures in excess of 32 "C and 33 "C were common . The paper then proceeds to describe the methods employed to attempt to improve the climatic conditions on the district, especially with regard to the coal face and return airways and describes in detail the effects of reversing the district airflow direction, employing homotropal ventilation, on the climatic conditions. The results of this reversal have been dramatic and have resulted in a substantial improvement in the climatic conditions experienced , however problems have been encountered with the control of methane gas since the changeover. The final part of the paper describes the results of computer simulations to analyse the effect of various ventilation designs on the predicted climate for future production districts in order to de- fine a district layout which will produce acceptable climatic conditions in the working zone without the need to use refrigeration techniques and which will improve methane gas control .

Jan 1, 1997

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By D. Castillo

The effectiveness of a flotation column is due principally to the addition of wash water to the froth phase. The wash water flow rate can be significant, especially so for systems yielding a high weight recovery of fine solids, e.g. zinc sulfide flotation. Therefore, it is critical to recognize and assess the impact of the water addition upon upstream separation stages. This paper examines column flotation circuit configurations using data from a portable 2 t/day pilot plant. The objective is to provide an improved basis for column design, either as a retrofit or as part of a new circuit.

Jan 1, 1990

By Max Friedemann, Alexandros Bousdekis, Anna Gustafson, Helmut Mischo, Håkan Schunnesson

Many devices used in mining are not monitored by sensors or do not have their own intelligence. By retrofitting sensors and real-time data processing, machines can be integrated into an existing digital infrastructure. Within the project Mine.io funded by the European Union a Sandvik DE110 exploration drill rig is being digitized using various AI algorithms at research and education Mine “Forschungs- und Lehrbergwerk Reiche Zeche (FLB)” of TU Freiberg. The aim is to increase the productivity of drilling with real-time evaluation of the current rock to be drilled and the current maintenance status of the drill rig. The drill rig is equipped with a speed sensor, pressure sensors in the hydraulics, 3-axis vibration sensor, borehole length measurement and temperature sensor. The sensors are additionally attached to the drilling rig and no structural changes on the drill rig are necessary. All data are processed real-time at a server structure outside of the mine using AI algorithms to analyze which rock (ore or host rock) is being drilled and to perform predictive maintenance. Processed Data are visualized for the operator to optimize the workflow and the productivity.

Feb 1, 2025

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By Ezz El Din Abdel Hakim Khalaf, Khalid S. Essa, Marc Munschy, Mohamed A. S. Youssef

This study focused on joint interpretation of the aeromagnetic and radiometric data to allocate and describe the structural elements and mineralization zones such as uranium, gold, and sulfide in the Gebel Umm Tineidba and its surroundings, Eastern Desert, Egypt. The study region is covered by exposures of Precambrian rocks such as gneisses, migmatites, ophiolitic mélange, metavolcanics, younger granites, and Quaternary sedimentary covers. The application of the total intensity magnetic and reduced-to-pole maps, power spectrum, analytic signal, tilt-angle, and local wavenumber maps helps in recognizing magnetic sources distribution, lineament features, and mineral zones delineation. The obtained results indicate that the depths of the deeper NE–SW, NNE–SSW, and N–S trending structures extend from 400 to 1750 m and shallower ones range from 100 to 400 m. Finally, the main trends of these structures affect the probable mineralization zones.

Sep 22, 2022