Search Documents

By G. R. Addie

While the cost of transporting raw phosphate matrix from a pit to a processing plant via slurry pipelines is more efficient than it could be by rail cars, conventional trucks or belt conveyors, it still amounts to many millions of dollars, and in many areas there still exists much room for improvement. By taking advantage of pipeline test data on different slurries, it is possible to reduce costs by optimizing pipeline diameters, operating velocities and slurry concentrations. Better wearing, more efficient pump designs are now available which, if applied correctly, can lead to significant savings. The authors discuss what benefits are possible in relation to the electrical operating and wear maintenance costs and go into some of the factors associated with taking advantage of these benefits, identifying what they see as being practically possible.

Jan 1, 1998

By Nikhil Dhawan, Débora Moreira, Yogendra Pratap, Himanshu Tanvar

A glauconitic siltstone sample with a potash content of 10% is investigated as a potential potash source. The fine grain structure comprises potash bearing phases of glauconite, muscovite, and microcline. The as-received samples showed poor dissolution ~ 5%. Planetary ball milling was attempted for the dissociation of the underlying silicate structure for the potash release, and ~ 60% potash was obtained after 12-h milling. Mechanical activation (8 h, 60% NaOH) prior to heat treatment (600 °C, 30 min) was found successful in recovering more than 95%K values from glauconite. The final residue consists mainly of quartz, indicating a complete breakdown of the silicate matrix. The mechanical activation process followed is simple, adaptable, and less energyintensive compared to existing methods.

May 4, 2020

By H. G. Kok

The concept of mobile crushers is not new. Since their introduction about twenty-five years ago, mobile crushers have continued to gain widespread attention. Mobile crushers reduce minerals in the open pit mine to sizes which can be transported by belt conveyors thereby reducing or eliminating the need for truck haulage. Truck haulage is costly, often representing as much as 50% of the total mining cost. More than 80% of the cost of truck haulage is for fuel and lubricants, tire replacements, and operators' wages, and it can be anticipated that the cost of these items will continue to increase at a steady pace. Compared to truck haulage, transportation by belt conveyor is more energy-efficient, less labor-intensive, and less subject to inflation. Therefore, mobile crushers, used in conjunction with belt conveyor systems, offer one of the most effective available methods of reducing energy consumption and mining costs,

Jan 1, 1980

By H. Cho

There is an indication that high-pressure roller milling promotes selective liberation due to preferential breakage along the mineral boundaries. A study was undertaken to compare the degree of liberation obtained by high-pressure roller milling with that of conventional ball milling. Coals with different HGI's were ground in a high-pressure roller mill and a ball mill to produce products with similar size distributions. The products were then subjected to float-sink separations to determine the degree of liberation. Also, the relative cleanabilities were compared by separating the ground products by froth flotation. The results from this study are presented in the paper.

Jan 1, 1994

By E. R. Drevdahl

It has been suggested that we at the University of Arizona present a paper covering the origin, philosophy, and results of the College of Mines program in the field of computers and operations research. I have worked with the program since its beginning, and I will try to outline the developments as they have taken place. The formal development of the educational and research program in the field of Operations Research and Computer Applications at the College of Mines, University of Arizona, began in early 1957. During the year, the University offered its first formal instruction in computer programming. This was my first introduction to computers, and it did not take long to realize that this new tool had a potential that could be profitably utilized by the mining industry. In March 6f 1957, the University Computing Center began operations with its IBM 650 computer. This machine was the only computer of this size in the local area at this time, The first programming effort was in machine language and the programming cost could only be justified for repetitive-type of problems. The progress in the computer field moved very rapidly and with the development of the many compiler and assembly programs and the addition of sub routines to the computer library, the scope of problems that could profitably be investigated by computers expanded rapidly.

Jan 1, 1963

By Ronald R. Hartman

I can recall a time 10 or 12 years ago when I spent a pleasant Sunday afternoon driving to Jim Thorpe, Pennsylvania to see a carnotite deposit that had recently been discovered. The announcement of the discovery stated that it was in the Pottsville conglomerate in a road cut along the highway. To my surprise, the highway was lined with cars and every weekend prospector for 100 miles had come to see the ?big uranium deposit of the east?. I literally had to stand in line to make a measurement with the scintillation counter I had with me. The thought at first occurred to me that this is evidence of how thoroughly the surface of the United States must have been prospected, more likely, perhaps it points out quite the opposite. A lot of time and energy was being spent in tracing the footsteps of others and a lot of time was spent looking for the obvious occurrences. The point is, that in the early days a tremendous amount of uranium exploration was carried out but few systematic surveys were made. Thorium anomalies were usually discounted after cursory surface field checks. Conversely, in airborne surveys - anomalies due to elevation changes or thin over- burden on hilltops were often investigated more thoroughly than smaller indications on hillsides and valleys. An adequate supply of uranium was nevertheless found due to the ingenuity and persistence of the geological profession and the public in general. This ?adequate? supply, like so many estimates for raw materials turned out to be far too low.

Jan 1, 1967

By J. M. Rios

This paper exposes the reasons that led the Empresa Nacional Minera del Sahara, S.A. (ENMINSA) to the selection of a conveyor belt system for the transport of phosphate rock over a distance of 100 kilometers. ENMINSA was created in 1962, with the main objetive of the exploitation of phosphate rock deposits in the Spanish province of Sahara, in North West Africa. Poor grade outcrops were known previously. A detailed geological research carried over the province led ENMINSA to the discovery of deposits not exposed, and of much higher grade. The sector known as Bu-Craa was chosen as the most promising, and was explored by means of drill holing and shafting. The important amount of information obtained permitted a detailed evaluation of the capacity and grade of the rich ore contained in the Bu-Craa area. Simultaneously with the systematic reconnaissance of the Bu-Craa deposits, ENMINSA developped the study of the technical and economical problems required for the beneficiation of the rock, which comprised five main groups of projects: rock exploitation; beneficiation plant; rock transport from the mine site to the Atlantic coast; storage, handling and loading facilities by the sea- side, and power plant. Once determined the location of the marine loading facilities, which to date are in an advanced stage of construction (figs. 1 and 2), the studies conductive to the selection of the best transport system from the mine to the ocean, along 100 kms. distance were undertaken.

Jan 1, 1968

By Gabriel Böde Jimenez Leon, Michael Karmis, Christopher Newman, Zach Agioutantis

"When utilizing high recovery underground mining methods, such as longwall or high-extraction room-and-pillar mining, the movement and deformation of the overburden propagate toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidenceinduced changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, the resulting strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed ruptures, upward, blocking stream flow or having the stream diverted into the fracture zone at the base (Iannacchione, et. al., 2010).Recent investigations on the effects of underground mining on surface bodies of water suggest that to determine the degree of stream impact one must also consider the geologic structure and thicknesses, surface topography, watershed drainage areas, width of river bed and rate of mining. Due to the complex nature and number of parameters affecting surface streams, subsidence modeling tools and software packages should be implemented throughout all stages of subsidence planning, prediction and control. The Surface Deformation Prediction System (SDPS) utilizes the influence function for the calculation of final subsidence deformations with respect to the angle of influence, supercritical subsidence factor as a function of the percent hard rock, edge effect offset distance, and surface topography. Developed more than 25 years ago, SDPS has been continually updated with new analysis and prediction features, providing a reliable and versatile program for subsidence management methodologies. Most recently, the program has been updated to evaluate the effect of varying surface topography in the prediction of horizontal displacements, referred to as ground strain, allowing for the accurate three-dimensional representation of surface deformations in mountainous terrain (Agioutantis and Karmis, 2014). Ground strain has become one of the predominant deformation indices used in the evaluation of potential damage to surface structures (Karmis et al., 1995). Ongoing work with SDPS software seeks to investigate the calculation of ground strain in SDPS and its ability to accurately and realistically predict damage to surface streams due to underground mining operations."

Jan 1, 2015

By R. L. Bullock

For the past 30 years there has been a gradual evolution of mechanical excavating systems in underground hard rock mining applications. This paper traces many of the tests of various tools and methods to break hard rock, up to the present. The tools include impact hammers, boring machines, disc on boom mining machines, disc on revolving wheels and drums, picks and drag bits on revolving hubs, rock splitters, slot cutting systems, and with customized explosives/powder mini-blasting. While the progress has been slow, successes are being achieved in hard rock and more opportunities exist today than ever before.

Jan 1, 1995

By I. J. Jansen, C. L. Hooks

Successful soil construction involves prepa¬ration of an adequate base, selection of high quality soil ma¬terials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experi¬ments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construc¬tion. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By David J. Boron

The United States has the largest total (364 billion metric tons) and recoverable (182 billion metric tons) coal reserves in the world.1 However, progressive coal utilization in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. New technologies are being pursued both to appease these environmental concerns and improve economic performance and process efficiency. These technologies, however, have not reached the level of effectiveness required for optimum operation. If more stringent emission standards are imposed, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the successful development of new and advanced coal cleaning technologies in order to continue and promote the use of coal in this country. The EPA New Source Performance Standards In 1979, the Environmental Protection Agency in response to the amendments to the Clean Air Act of 1977 issued new source performance standards (NSPS) for utility and industrial boilers. The NSPS set emission standards for sulfur dioxide, nitrogen oxides, and particulates affecting boilers of 250 MM Btu per hour heat input or 'greater that started construction after September 1978. Plants starting construction or in operation before September 1978 remained subject to the provisions of the regulations promulgated in 1971, i.e., SO2 emissions of 1.2 15/MM Btu. The NSPS for SO2 emissions provides a sliding scale for SO2 reduction depending on the sulfur content of the run-of-mine coal, with an upper limit of 1.2 lb of SO2 per million Btu and a minimum emission level based on 70% SO2 removal. Table 1 summarizes the EPA NSPS for SO2 emission standards.

Jan 1, 1983

By K. E. Burgher

Since World War II, the need for the use of explosives in construction, mining, and quarrying near congested urban areas has increased dramatically. Often times a coal mine, once isolated from a city, finds itself surrounded by residential and commercial structures. The United States Bureau of Mines and others have researched blast design to a point where ground vibration and airblast damage can be avoided. A problem still exists, however. It is the fact that people often react to only the loud noise associated with a blast although it may not cause damage. Most often it is the concussion of a blast, less than 20 hertz and inaudible, that produces damage. Public fear from the "startle" and "fright" of loud blast noise greater than 20 hertz leads to the complaints which are generally unfounded. See Thackray, Touchstone, and Baily (1975) for a further discussion of the startle effects of loud sudden noises. When blasts are designed in accordance with U.S.B.M. specifications, management generally has little to worry about with respect to damage claims. Complaints, however, still arise when the noise is accentuated from the blast. It is meteorological conditions which dictate how the sound levels will propagate. Some mines use small pilot test shots (generally one-two lbs) to determine when atmospheric conditions favor sound travel.

Jan 1, 1987

By J. T. Clancey

The potential inadequacy of natural gas reserves to supply projected requirements in the 1980's has been pointed out.(1,2) As a result, interest has arisen in the development of new, potentially low-cost processes for the conversion of coal into high BTU gas. In June, 1964, the office of Coal Research (U. S. Department of interior) and Consolidation Coal Company (now a subsidiary of Continental Oil Company) entered into a contract to continue work on coal gasification utilizing the Consol CO2 Acceptor Process. Work under this contract has been specifically directed toward the use of lignite as the carbonaceous feed, although the process is also applicable to non-caking subbituminous coals. The primary objective of this work was to establish the technical feasibility in continuous bench-scale equipment, of the novel features of the C02 Acceptor Process. Secondary objectives were the testing of commercially obtainable acceptors and the design and economic evaluation of a commercial facility. The bench-scale process development has been completed successfully and the construction of a large pilot plant at Rapid City, South Dakota, has been authorized. It is the purpose of this paper to review the technology of this new gasification process and to present the current projected economics of a plant producing 250 MM SCFD of pipeline quality gas.

Jan 1, 1969

By Frank M. Howell

Creede, one of the younger major mining camps in Colorado, grew spectacularly to a town of eight or ten thousand people in the early 1890's following discovery of rich ore in the Amethyst and Last Chance mines. Gross metal production in gold, silver, lead, copper and zinc rose to a maximum of four million dollars a year in 1893. Annual production dropped to much lower figures and ranged between one hundred and five hundred thousand dollars per year during the period from 1914 to 1940. Production reached a gross of eight hundred thousand to one million dollars per year by the mid-1950's. In the years 1953 to 1957, Steven and Ratté conducted geologic investigations which were carried on as part of a cooperative program of the U. S. Geological Survey and the Colorado Metal Mining Fund Board. In a preliminary report on the Creede District, Steven and Ratté suggested that the Bulldog Mountain Fault Zone appeared to be a favorable structure to prospect. On the basis of that recommendation, augmented by independent work done by Manning W. Cox, the property was acquired, transferred to Bulldog Mountain, Inc. and financed by an O. M. E. loan. Late in 1963 Homestake Mining Company, under a Lease and Option Agreement, backed the venture by furnishing additional funds plus management.

Jan 1, 1969

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016

By Walter N. Campbell

The Simon Silver Mine is located near Mina, Nevada, approximately 50 miles northwest of Tonopah and 40 miles east of Hawthorne. It is an old property which was last worked in 1932 and closed operations due to problems arising from low metal prices. Federal Resources Corp. acquired the property in 1963 and undertook a completely new development program since the old surface plant and underground workings were beyond feasible repair. The deposit of silver, lead, zinc and copper is predominantly replacement of limestone. In the summer of 1964, a new surface plant was constructed and on December 2, 1964, sinking of a three compartment vertical shaft started and was completed to a depth of 1088 feet in April of 1965. Following the sinking program an 850 foot crosscut was driven to intersect the mineral zone on the 1000 level after which drifting, crosscutting and raising totaling some additional 4280 feet has been completed along with considerable diamond drilling and long holing into the walls. To date, two ore bodies have been encountered and test stoping operations are underway together with development of the 800 level for servicing, ventilation and access. The present development of ore is directed towards substantiating sufficient reserves to warrant the construction of a flotation mill.

Jan 1, 1967

By Neal Cochran

I consider it a distinct privilege to be afforded the opportunity of discussing the program of the Office of Coal Research. The principal activities I will be discussing are concerned with projects that fall in the utilization area. I will, to be sure, touch on other activities of the Office of Coal Research but am not equipped to discuss these activities in great detail. Research activities of the Office of Coal Research are conducted on a contract basis with commercial, academic, and non-profit institutions. We do not operate any laboratories of our own but we do maintain a very small staff for technical and administrative supervision of our contractors. We have consistently attempted to interest outstanding, creative, and practical research organizations in our program. We are constantly seeking the imaginative new idea that will materially reduce the cost of mining coal, transporting it, or will process it into a more convenient and useable form. In assessing proposals and in developing our program, we search for the improvements that will develop large-scale new uses for coal or coal products or those that support these new uses.

Jan 1, 1963

By Ed L. Schrader

Kaolin of the Georgia-south Carolina "Clay Belt" are used in a wide variety of filler and extender applications. Sane applications specifically require the performance enhancement delivered by incorporating kaolin into the product formulations. Other applications are less specific in requirements for an inert mineral filler. In order to be a feasible candidate for filling and extending, a mineral or mineral product must be generally inert (except where specific interaction with the filled medium is desired), inexpensive, easily handled and transported in a variety of forms, accessible to a broad segment of the desired market, and must exist in sufficiently large ore reserves as to assure production for many years. Of course, more precise requirements are necessary in specific applications of a prospective filler material.

Jan 1, 1985

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By Alexander B. Ikonnikov

All known bauxite deposits in China occur in its eastern half, and almost all of them are found in the Carboniferous and the Permian. They are of platform origin, but contain diaspore as the major ore mineral. There is only one known deposit composed of gibbsite. The most valuable deposits are sedimentary ones formed in local depressions on the edges of platforms during marine transgressions. They lie on Upper Cambrian or Middle Ordovician limestone that was weathered for a long period of geological time. Generally, Chinese bauxites are low in iron, and have a rather low alumina/silica ratio.

Jan 1, 1984