Search Documents

By D. J. Rose

The San Miguel Mine is owned by San Miguel Electrical Cooperative, Inc. and operated by Atascosa Mining Company, a wholly-owned subsidiary of Morrison-Knudsen Company, Inc. This multiseam, single-zone lignite surface mine is located near Jourdanton, Texas, 110 kilometers (68 miles) south of San Antonio. Lignite extracted from four closely-spaced seams is used to fuel the 400-MW San Miguel Power Plant. Recovery depths range from 7 to 37 meters (25 to 120 feet). The mine began stripping operations in the spring of 1980 and now produces approximately 2.5 million tonnes (2.8 million tons) of lignite annually. Atascosa Mining Company is responsible for production, maintenance, engineering, and management services. Production responsibilities include topsoil removal, overburden removal, lignite mining, spoil pile regrading and topsoil replacement, as well as ash disposal and construction and maintenance of water retention and diversion facilities.

Jan 1, 1984

By R. W. Lankston

Uranium mill tailings disposal facilities present unique problems with respect to siting, design, and long-term stability because their contents remain potentially hazardous for 100,000 years. Dawn Mining Company, operator of a uranium mill in Washington, undertook geological and geophysical studies relative to planned expansion of existing disposal facilities. Seismic refraction and reflection, resistivity, and ground magnetics data were integrated with limited drill data to determine the configuration of Quaternary sediments and the underlying basaltic and granitic bedrock. Analysis of multiple reflections and magnet modelling on a micro-computer with CRT graphics added detail to the interpretation.

Jan 1, 1980

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By J. C. Irvine

Meramec Mining Company, a joint venture by Bethlehem Steel Corporation and St. Joe Minerals Corporation, is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge Mine located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during an exploration program to discover new lead orebodies. An airborne magnetometer survey which was run by the U. S. Geological Survey, the Missouri Geological Survey, and several min¬ing companies was published in 1950 and showed an anomaly in the Pea Ridge area. Test holes drilled in 1953 and 1954 revealed the presence of a large orebody of probable commercial significance; additional drilling in 1956 and 1957 provided confirmation of this. Meramec Mining Company was incorporated in 1957 and shaft sinking began in the latter part of that year. The Pea Ridge orebody lies under about 1300 feet of sediments. It is tabular, about 2600 feet long and up to 600 feet thick, and lies in an approximate east-west delineation. The orebody dips about 800S and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite, The Pre-cambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 feet 1 inch in diameter and 2500 feet deep. No. 1 shaft, equipped with an "A" type head-

Jan 1, 1972

By Clarence Hardy Long

In January of 1969 the United States Department of Health, Education and Welfare, through the National Air Pollution Control Administration, published a series of Air Quality Criteria (4'S) and Control Techniques (6,7) for air pollutants in compliance with the 1967 Clean Air Act which will affect the operation of all fuel burning equipment in the very near future. The design of equipment for the future which will use fossil fuels will also be affected. The purpose of this paper is to discuss some of the modifications which might be anticipated in the future for fuel burning equipment. One class of the several air pollutants looked at first by the USDHEW was the sulfur oxides. Other pollutants, such as nitrogen oxides, will be studied and controls for these will supposedly be written in due time. The obvious use of low-sulfur fuels, coal, oil and natural gas is suggested by the Control Technique(6). Conversion to other sources of power, such as nuclear energy and hydropower, is also suggested. The statement is made that since possible hydroelectric sources are limited and nuclear plants are not yet available on a large scale, the changeover to these sources of power will not be overnight. The bulletin (6) suggests that one possible solution in some areas may be the use of low sulfur coals for short periods of time during periods of severe air pollution. A curve showing the effect of this was given in the 1969 April issue of the Power magazine, where A. E. Boyer and F. B. Kaylor of Stone and Webster also described a computer program called DOSAGE which might be used to check weather, temperature, humidity, wind direction and velocity, and sound an alarm when that 0.1% of the time per season is here that requires the use of low-sulfur fuel. Inversion is eminent! Once this has passed operation on regular fuel may be resumed. This would mean a separate storage

Jan 1, 1970

By Henry E. Swanson

In the early 1960's the Company, then named the United States Smelting Refining and Mining Company, was drilling the Continental ore body located near Fierro, New Mexico. Reserves of underground ore of sufficient quantity were indicated to build a mill. At the same time some ore from the Continental No. 1 mine was being milled at the Company's Bullfrog Mill, formerly a lead-zinc mill. The copper ore in comparison to the lead-zinc ores was very hard, abrasive, and heavy. These factors pointed out the possibility and attractiveness of autogenous grinding. While prior to this some study had been given to autogenous grinding, no large scale tests had been made. Such a program was carried out and from the pilot plant data the following was established: 1. Grinding of the ore by autogenous means could be accomplished. 2. This could be done in one stage; however, not at a satisfactory tonnage throughput rate. Thus, the use of a secondary unit has been employed. 3. Grinding in the secondary unit could be done by pebbles generated in the primary unit. This resulted in the scheme whereby the ore would be ground 100% autogenously. 4. Liberation of the copper minerals was excellent so that good recovery at a satisfactory concentrate grade would be obtainable.

Jan 1, 1976

By Harald F. Solberg

A preliminary study of the performance of a 4-inch Krebs cyclone at near rope conditions and different feed slurry temperatures was completed. Results suggest that temperature influences the x50c size which, in turn, did not depend upon spigot diameter. The bypass correction to a reduced efficiency equation incorporating the concept of a critical size xo was a function of fractional water recovery to underflow and may depend on feed size and feed percent solids. Further experimentation is required to develop an accurate model at near rope conditions.

Jan 1, 1981

By J. Gordon Scott

The Iron Ore Company of Canada has now been operating a computer for the grading or blending of direct shipping ores for two years. This paper deals with the computer application pertaining to the grading of direct shipping ore. It consists of five sections. The first part deals briefly with a description of the operation of the Iron Ore Company of Canada; the second with the source and flow of the various data required to grade or blend ore; the third briefly outlines the computer programs used in this application; the fourth illustrates the mathematical approach used to properly blend ore. The final section briefly describes other technical computer programs.

Jan 1, 1964

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products, The original source of potassium was wood ash (hence the name potash), However, today the term potash refers to all commercially important salts of potassium. Sylvite, usually found associated with halite, is the predominant economic potash mineral; carnallite a lesser important source of potassium chloride, while langbeinite is important as a source of potassium sulphate. The world's first potash mining operation commenced in Strassfurt, Germany about 1860, Since that time the industry has grown steadily to its present annual volume of about 30, 000, 000 tons of potassium chloride products or 18, 000, 000 tons of K2O equivalent, potassium chloride or "muriate of potash" being equivalent to 63. 1% pure K2O, WORLD POTASH RESERVES ARE NOT EVENLY DISTRIBUTED The earth's crust contains 2 to 3 per cent potassium, mostly in the form of insoluble silicate minerals. The economically important deposits, however, are formed from brines concentrated by evaporation. The world's most important commercial deposits are of Devonian and Permian age, however soluble potassium bearing salts are presently being concentrated by evaporation in several drainage basins, notably Searles Lake, California, Great Salt Lake, Utah' and in the Dead Sea. At least twenty-four countries are known to have reserves of potash: Canada and the USSR have over 80% of the presently known world reserves, (Figure 1)

Jan 1, 1972

By J. B. Cabezas

The metallurgical processes that are frequently applied today use strong solutions and are of alkaline, acidic, or organic nature. These play a very important part in recovery of values from many ores. These solutions are of such a chemical nature that they are generally corrosive, flammable, and contaminating. In most cases, they are highly dangerous to the environment. Within the extractive metallurgical industry, it is also very common to have to deal with the handling of contaminating solutions with a high content of cyanide, arsenic, mercury, lead, copper kerosene, acid and many other components whose temporary or permanent confinement within the process must be adequate and absolute.

Jan 1, 1986

By S. Veeramasuneni

The interaction of soluble salt particles in their saturated brines is of interest from both a fundamental and practical perspective. The state of dispersion/aggregation of alkali halide particles as determined by optical microscopy can now be described based on non-equilibrium electrokinetic measurements for alkali halides. These results indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. These experimental results can be explained based on the interfacial polar interaction theory. In this regard the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems.

Jan 1, 1997

By Gordon T. Austin

Garnet is the general name for a family of complex silicate minerals having similar physical properties and crystallizing in the isometric (cubic) system. All garnets have the same general chemical formula but vary greatly in chemical composition. The name garnet is derived from the Latin word granatus, meaning like a grain, which refers to the mode of occurrence wherein crystals resemble grains or seeds embedded in the matrix. GEOLOGY Mineralogy Chemical Properties: The general formula for garnet is A3B2(SiO4)3, whereas A can be calcium, magnesium, ferrous iron, or manganese, and B can be aluminum. ferric iron, or chromium, or rarely titanium. The formulas and names of common garnet species are: [ ] Almandite and almandite-pyrope solid solution garnets are the best abrasive types, but andradite, grossularite, and pyrope also are used. All species of garnet have been used as gemstones. The structure of garnet consists essentially of isolated SiO, tetrahedra connected by oxygen-cation-oxygen bonds through the distinct A and B group cation sites. Within this structure magnesium, ferrous iron, and manganese easily interchange and substitute for each other in the A cation position, and calcium does so less readily. Additionally, aluminum, femc iron, and chromium substitute for each other to a limited extent in the B cation position. This ability to substitute or exchange ions without changing the crystal structure is called isomorphism, and garnet is one of the finest examples of a isomorphous series. Because of this isomorphism there is complete solid solution between certain garnet species but not between others. Fig. 1 illustrates these solid solution relationships. Some rare species of garnet are known that illustrate the wide range of cation substitution that the garnet crystal structure can accommodate. They include: [ ] These rare species are not of interest for industrial applications, but can be of interest to mineralogists and the gem industry. Physical Properties: Garnet displays the greatest variety of color of any industrial mineral. Garnets have been found in all colors except blue. For example, grossularite can be colorless, white, gray, yellow, yellowish green, various shades of green, brown, pink, reddish, or black. Andradite garnet can be yellow- green, green, greenish brown, orangy yellow, brown, grayish black or black. Pyrope is commonly purplish red, pinkish red, orangy red, crimson, or dark red; and almandite is deep red, brownish red, brownish black or violet-red. Spessartite garnet can be red, reddish orange, orange, yellow-brown, reddish brown, or blackish brown. A few garnets exhibit a color-change phenomenon. They are one color when viewed in natural light and another color when viewed in incandescent light. Because of the great variation in color of garnet within each species and similarities in color between garnets of different species it is recommended that garnet identification not be based on color alone. The Mohs hardness of garnet varies from 6.5 to 9.0. Grossularite and uvarovite have a hardness of 6.5 to 7.5; andradite is 6.5 to 7.0; and pyrope, almandite, and spessartite are 7.0 to 7.5 in hardness. There are reports of almandite having a hardness of between 8.0 and 9.0. As with hardness, the specific gravity of garnet varies considerably. The specific gravity may be as low as 3.2 or as high as 4.3 depending on chemical composition. Garnet crystallizes in the isometric system with rhombic dodecahedra and trapezohedra the most common forms. Crystals also form in combinations of dodecahedra and trapezohedra or either of these in combination with hexoctahedra. Crystals can have cubic or octahedral faces, but these are rare. Under favorable conditions of formation garnet will crystalize in nearly perfect forms that rival study models. Garnet also forms as irregular blebs, grains, knots, or masses, with or without distinguishable crystal faces, and as coarse- or fine-grained granular masses that appear to be totally lacking in crystal form. The fracture of garnet also shows great variation. In some garnets, particularly those that are well crystallized and glassy in appearance, the fracture is subconchoidal to conchoidal. Other, more poorly crystallized garnets exhibit a fracture that can only be described as uneven. Garnet occasionally has an indistinct dodecahedral cleavage. Certain species of garnet from specific locations have a pronounced laminated structure consisting of planes of weakness along which parting takes place. This parting may resemble cleavage, but since it is mechanical and not related to crystal structure it is not true cleavage. The optical properties of garnet are sensitive to even small changes in chemical composition or strain in the crystal structure. For this reason each species does not have a single index of re- fraction (IR) but has a range of 1Rs. Uvarovite in its pure form should have an IR of 1.870, but in nature samples vary from 1.74

Jan 1, 1994

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The STG integrated method of grouting can be divided into the several phases as outlined in preceding chapters. For convenience in describing technical procedures, they can be grouped as: 1. Investigations in non-geotechnical, exploration bore¬holes. 2. Drilling the holes necessary for geotechnical investiga¬tions and for grouting. 3. Conducting appropriate hydrogeologic tests in those holes and consequent calculations. 4. The preparation of a clay mortar. 5. The preparation of a clay-cement grout with additives. 6. The injection of the grout. 7. Checking the quality of the grout curtain. Items 2, 4, 5 and 6 are discussed below. These activities contain the procedural aspects of grouting. 7.1 DRILLING GROUT HOLES Grout holes belong to a very select class of drillholes. The necessary drilling equipment must enable the operator to drill the holes in inclined, twisting directions. In addi¬tion, the equipment must permit drilling under structurally and hydrogeologically complex conditions. The equipment must permit the operator to conduct specific testing activi¬ties in the drillholes. These activities include hydrodynamic analyses, flowmetric analysis, and the installation and re¬moval of deflectors, packers, grouting plugs, casings, lin¬ers, pumping facilities and other work. As explained in Chapters 5 and 6, the grouting of sat¬urated rock is conducted both through holes drilled from the surface and through holes drilled from the face of a shaft, drift, or tunnel. The drilling of grout holes from the surface can be carried out by an aggregate of equipment that can be the same equipment used for drilling exploration boreholes. Depending on the projected depth of the holes, the STG ZIF- 1200MR and ZIF-650 drilling rigs (or modifications of them) are used. The SKB-4, SKB-5 and SKB-7 high-output drilling rigs (workover rigs) have been used in recent years. The STG BMP-24 drilling rigs are used for carrying out the descent-lifting operations for drilling holes from the sur¬face. In a number of cases, the UKB-500C, URB-3AM and URB-2A power-fed drilling equipment is used for drilling holes from the surface. It should be noted that the drilling of grout holes usually requires an electric drive assembly. Drilling with diesel drive assemblies would be used only to preclude the possi¬bility of losing electric power during drilling operations. Turbine drilling would be used only for appropriate techni¬cal-economic reasons. The selection of the grout hole design is determined by the hydrogeological and structural geological conditions at the site as interpreted in Chapters 2 and 3. The design of grout holes must be as simple as possible in order to min¬imize costs. Hole design guidelines can be adopted as a basis for this purpose, unless site-specific conditions require otherwise. The mouth of the drillhole must be outfitted with a guide-pipe having a length of at least 2 m and an outside diameter from 219 to 234 mm. The upper part of the hole must be attached by a jig consisting of borehole casing that has a diameter ranging from 108 to 146 mm. The length of the jig h is determined by the equation [ ] where k = 1.1 to 1.2 is the load factor; P,, is the injection pressure of the grout into the mouth of the drillhole; D is the external diameter of the jig pipe; m = 0.6 to 0.7 is the work condition factor; T[ ].1 MPa is the bonding value of the rock cemented to the jig. The grout hole is drilled from the jig shoe to the de¬signed depth using a rock-crushing bit with a diameter of 93 mm or more. However in complex hydrogeological condi¬tions when the shaft intersects unstable rock, other hole designs can be used. The diameter of grout holes must permit an aggregate of investigations to be conducted in them using down-hole borehole geophysical and flowmetric logging instruments. It is necessary to cement the casing strings reliably in the grout holes, thereby permitting the injection of the grout under high pressure through the pres¬sure tight mouth of the borehole. Technological details for drilling grout holes such as the rotational rate of the drill bit, the axial load on the rock¬crushing bit, and the drilling fluid flow rate are optimized for the specific rock-hydrogeological conditions largely by experience. The hole diameter and type of rock crushing bit are important variables in these details of drilling. It is advisable to drill holes using water as the drilling fluid. However in those cases where the hole walls are unstable or under very high ground water pressure, the use of a well¬ engineered drilling mud should not be precluded. Unfortu¬nately, drilling mud can influence test results. When steeply dipping fractures with inclination angles of more than 60 to 70° are encountered, it is necessary to drill guided, inclined grout holes. This procedure permits the maximum number of fractures in each hole to be stu-

Jan 1, 1993

By R. V. Ramani

In 1970, of the 603 million tons of coal produced in the United States, 339 million tons, or 56%, were produced by under- ground mines. While the ratio of underground to surface production has been decreasing in the last few years, it is anticipated that a 60:40 ratio of underground to surface-mined coal will remain for some time. Underground coal operators are continuing to invest in new mines and are interested in increasing the efficiency of all their operations. One area for improvement is in mine planning and design, particularly in the area of selection of equipment for operation. Because of the availability of a wide variety of equipment, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, such a choice must be made on the basis of technological facts and forecasts related to the mining operation. If the mining conditions can be reasonably predicted, along with a mining plan, it should be possible to insure the selection of the right equipment for the particular application. In order to increase the efficiency of underground coal operations, it is necessary to understand not only the operating system in detail, but the inter-relationships between system components and the operating environment. With such an understanding comes the application of simulation and other operations research techniques to plan and operate mining systems. Computer simulation studies have been successfully adapted to underground coal mining, and applications by Prelaz et al. (1965), and Manula and Sanford (1969) are some that are being used by the mining companies. However, a need still exists for better understanding of certain intra-system and system-environment interactions in order that computer simulation programs may be provided with better input data for more effective application. This paper deals with one aspect of the coal-winning system in need of better definition, namely, studying the performance of continuous miners.

Jan 1, 1973

By R. Q. Honaker

Although the fundamental principles of hindered bed classifiers are relatively simple, the complex interactions between the operating parameters provide a degree of difficulty that hinders the ability for on-line plant optimization. Thus, a dynamic population balance model was developed for determining the hindered settling velocity of particles varying in density and size. The steady-state results of the model include partition curves as a function of particle size and density as well as metallurgical data. A statistical comparison of the simulation results with those obtained from industrial units reveal a high level of accuracy with adjusted R2 values greater than 0.95.

Jan 1, 1999

By George A. Snyder

The presence of moderate to high concentrations of colloidal clays in coal preparation plant waters can cause serious operating and economic problems for a coal company. Among the host of possible problems are the following: 1) Poor separation of clays in the plant thickener, resulting in: a) Increased ash in the clean coal. b) Increased specific gravity of the wash water and decreased coal recoveries at the desired quality. c) Increased thickener operating costs in trying to overcome the problem. 2) Decreased solid concentrations in the thickener underflow and increased pumping requirements to meet solids withdrawal requirements.

Jan 1, 1979

By L. E. Sausa

Measuring the specific gravity of a pulp in concentrating plants is a relative, y simple procedure, but the desired accuracy is often difficult to attain. Many plants use the system of weighing a known volume of the pulp on a scale. In many cases, this method is quite accurate, but obtaining a true sample presents quite a problem. This is especially true when the pulp tends to froth, the solids settle rapidly, or the flow is fast at the point of sampling. There is also the problem of the operator neglecting to take the sample because of duties elsewhere, or, if everything Is apparently running smoothly, he assumes the pulp density is also all right. In 1952, the Pine Creek plant of Union Carbide Nuclear Company began working on a better method for measuring and controlling pulp density. After an extensive investigation of different methods for measuring the specific gravity of moving pulps, the Research Department decided that the bubble tube method appeared to be the simplest and most promising for our applications. It consists of two bubble tubes, of different lengths, submersed in a pulp. Low pressure air is supplied to, the two tubes through sight bubblers to maintain approximately equal volume of air to each bubble tube. The bubble tubes are also connected to a differential manometer, one to each side. Therefore, knowing the vertical distance between the outlets of the bubble tubes, the manometere can be calibrated to measure directly the specific gravity of the pulp. (Figure No. 1 illustrates this model.)

Jan 1, 1960

By Hans Ehdwall

INTRODUCTION Investigations of radon and radon daughter concentrations in Swedish [non-uranium] mines started in the late 1960's. The first screening measurements showed that the average annual exposure to radon and radon daughter products was 4.7 WLM. The main reason for high radon and radon daughter concentrations was inefficient ventilation and radonrich water entering the mine. In the radon regulations worked out later it was stated that no miner should be exposed to more than 60 000 pCi h/1 equilibrium equivalent concentration of radon annual exposure, corresponding to 3.6 WLM. Now, 1981 the situation has changed considerably. From the average annual exposure of 4.7 WLM in 1970 it is now only 0.7 WLM. Sweden has up to now had only one [uranium] mine and the work there has only been investigative. However, there are plans for a commercial uranium mine in another part of Sweden. The radon problems in these mines are widely different depending on the mineralogy. NON-URANIUM MINES The radiation problems in Swedish mines were not recognised until the late 60's. The first radon and radon daughter measurements were made in some sulphide ore mines in 1967 (1). The radon and radon daughter concentrations were surprisingly high for non-uranium mines. In order to have a complete picture of the radon situation in Swedish mines the National Institute of Radiation Protection (NIRP) decided to make measurements in all, at that time about 60 mines (2). To get results as fast as possible measurements on radon gas seemed most appropriate to start with. Sampling was made by mailing a number of evacuated 4.8 litre conventional propane containers from NIRP to each mine. The containers were then opened at the place of interest. After sampling the containers were sealed and then mailed back to the institute for measurement. The measurements were made in ionization chambers. This method only gave the radon concentration and the radon daughter concentration was estimated by multiplying the radon concentration by an assumed equilibrium factor. The equilibrium factor is defined as the ratio of the total potential alpha energy for the given daughter concentration to the total potential alpha energy of the daughters if they are in equilibrium with the given radon concentration. The results of this first preliminary survey indicated that a great many of the Swedish miners probably had an annual radon daughter exposure of more than 3.6 WLM. As the radiation exposure in non-uranium mines was not regulated in either the Swedish Radiation Protection Act or the Swedish Labour Protection Act work was started on special radon regulations. A lung cancer mortality study was also started. To check the results of the first survey and to get experience and knowledge of radon problems in mines, it was decided that personnel from the NIRP should visit each mine for a detailed investigation of radon and radon daughter concentrations starting with the ones with the highest radon concentrations. The main reasons for these so-called "basic measurements" were: 1. To estimate the doses received by Swedish miners 2. To find the sources of the high radon and radon daughter concentrations 3. To find appropriate counter-measures 4. To determine the most typical equilibrium factor for each mine. Unlike most uranium mines the reason for high radon concentrations in non-uranium mines is seldom the occurrence of highly radioactive minerals. The main sources were found to be waste-rock and radon-rich water. In order to filter and warm up the inlet air, especially in winter time, it was very common at that time to suck the air through broken wasterock. By doing so the air was contaminated with radon from the waste-rock and radon-rich water in it. It is noteworthy that the radium and uranium concentration in the waste-rock is relatively low. The uranium concentration is only of the order of 15 - 20 ppm. The action to prevent this contamination of the inlet air was to change the direction of the ventilation and in the case of radon-rich water entering the mine the action was to prevent the air coming into contact with the water. The first calculation of the radon daughter exposure of Swedish miners was based on radon gas measurements. The radon daughter concentration was estimated by using an assumed equilibrium factor of 0.5. Later when the mines were visited by institute staff it was possible to compare the assumed equilibrium factor with the measured ones. It was found that the factor varied from 0.15 at the air inlet to 1.0 at the air outlet and the average equilibrium factor on workplaces for almost all mines was between 0.4 and 0.6. The result of the exposure calculation in 1970 showed that more than 40 % of the miners had an annual radon daughter exposure of more than 3.6 WLM. The overall average was 4.7 WLM and the maximum annual expo-

Jan 1, 1981

By Louis A. Panek

INTRODUCTION Block caving is distinguished from other types of mining in its requirements that the mineral body to be extracted must cave after a relatively large tabular open¬ing is created underneath it, and that the caving must be predictable and controllable for both operating and safety reasons. A mineral body that caves readily may present special problems with respect to ground support in the mining access openings, where stability, rather than failure, is the desired objective. The complete ex¬traction of a caving block, which may measure 50 to 100 m on a side and 100 to 300 m in height, tends to create a large void, resulting in significant changes in the ground stress system and a migration of rock from all directions toward the void; these events begin very early in the life of the mine and lead to additional spe¬cial problems with respect to control of ground move¬ments in the mine working areas, in the rock adjacent to the caving stope, and on the subsiding surface above the mine. Thus, the mechanics of an undercut-cave operation involve a broad range of geotechnical subject matter, including the determination of the lithostatic earth stresses, the structural properties of a large jointed rock mass, the flow properties of the fragments after caving, the stability of tunnel-like openings, and the stability and displacements of the rock structure (1 to 2 km in size) that surrounds the ore body. The objectives are achieved by in-place measurement of rock properties, laboratory tests, theoretical structural analyses of the related prob¬lems, measurements of structural behavior in and above the mine, and comparison of theoretical predictions with actual performance in order to interpret and refine the predictive capability. Undercut-cave mining (Julin, et al., 1973) differs from most other methods in that the caving is an essen¬tial and inherent part of the excavation process and in¬volves the movements of millions of cubic meters of rock over distances of hundreds of meters, as compared to the gradual 2-m settling of the overburden typical of full¬caving longwall coal mining. Undercut-cave mining may involve a rock mass on the scale of a 1-km diam open¬pit mine, but mining is several times deeper than that in the open-pit mine; furthermore, a large portion of the rock mass is in a failed, rather than a stable, state. Ground-control problems are inevitable in a situa¬tion where ground movements are occurring on such a large scale, and where the rock mass is expected con¬veniently to cave at one location but to be stable at an¬other. To devise effective responses to these ground¬control problems, one needs to know first of all what is happening, not merely at the point where the symptoms are observed, but more broadly with respect to the be¬havior of the entire mine rock-mass structure over the total area of extraction, including the effects on the sur¬face as well as those underground. Monitoring structural behavior on this scale would require a sizable group of people, if they attempted to measure all the significant mining-induced changes of ground displacement and pressure, even on a 100-m grid of points. The practical approach is to conduct the mea¬surements activity by a judicious sampling, making in¬termittent, concentrated efforts in selected areas of lim¬ited extent to study problems of immediate importance; simultaneously a minimum level of surveillance is main¬tained over the total structure to delineate long-term be¬havior trends in the major structure, which provide the baseline reference data that are so essential for interpre¬tive purposes. Mine-structure behavior depends not only on the mine extraction configuration and sequence, but on the rock structural properties and how they change from one location to another in the mine. Increasing attention is being given to determinations of rock strength and de¬formation by performing mechanical properties tests in place and in the laboratory, and by drawing inferences from the mapping of geologic structure in mine openings as they are driven and from the logging of cores ob¬tained from exploration drilling that may be performed primarily for delineating ore reserves. Monitoring of mine-structure behavior and inter¬preting it in terms of the growing excavations and the structural properties of the rocks have significant im¬pacts on designing the major undercut-cave operations of undercutting and drawing the ore, supporting the ac¬cess openings, and controlling surface subsidence. The purpose of this chapter is to call attention to the com¬mon ground-control problems encountered in undercut¬cave mining, to relate them to the mining process, and to explain the geomechanical approaches to analyzing these problems with emphasis on methods that are most readily available to the mine staff. UNDERCUTTING, CAVING, AND DRAWING A distinguishing characteristic of an undercut-caving method of extraction is the objective that the rock mass fails of its own weight in a predictable and controllable manner, after it is undercut by excavating a tabular¬shaped void, horizontal or inclined. Induced or forced caving refers to procedures that may be resorted to when the ore will not self-cave over the desired span. Block caving, panel caving, and mass caving are terms used to denote the particular sequence of undercutting and ex¬tracting the total area of the ore body on a single min¬ing level. The discussion herein is not specialized to any of these variations; the word block as used does not imply anything as to sequence. CREATING THE UNDERCUT A common undercutting method is to drive a series of drifts and blast the intervening pillars. Theoretical structural analysis and practical experience show that ground-support problems in the undercutting drifts and in underlying access openings as well (the same princi¬ple applies even if undercutting is done by belling out drawpoints from the slusher drifts) are minimized by retreat-mining across the undercut slot according to a sequence such that the growing undercut area retains a

Jan 1, 1982

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997