Search Documents

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

By B. R. Waples

Sometimes a project is born easy, sometimes a project has a hard time being born. Probably every project can say we had tremendous problems to overcome and they would all be right. This project had all things happen to it. Born easy, a hard time after being born, there were tremendous problems to overcome but here it is, a major copper project, a major operation, and a new source of copper for Mexico and the world market. La caridad is an ore body located in the state of Sonora in northwestern Mexico. It is at an elevation of 1,200 meters above sea level and the nearest major city is Hermosillo, the capital city of Sonora. Hermosillo is located approximately 270 kms (about 168 miles) to the southwest of la caridad. North of la caridad, 130 kms (about 81 miles), is the U.S. border town of Douglas, Arizona, which has a sister city on the Mexican side of the border -Agua Prieta.

Jan 1, 1979

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By C. L. Karr

Establishing suitable control of pH, a requirement in a number of mineral and chemical industries, poses a difficult problem because of inherent nonlinearities and frequently changing process dynamics. Researchers at the U.S. Bureau of Mines have developed a technique for effectively controlling such systems. This technique successfully combines the process control capabilities of fuzzy logic and the search capabilities of genetic algorithms. Fuzzy logic offers an effective mechanism for handling nonlinearities, while genetic algorithms can provide fuzzy logic controllers with real-time adaptive capabilities. This Bureau-developed technique is applied to a laboratory acid-base neutralization experiment. Nonlinearities in the laboratory system are associated with the logarithmic pH scale and the changing process dynamics are due to alterations in pH and buffering capacity input solutions. Results indicate fuzzy logic controllers augmented with genetic algorithms offer a powerful alternative to conventional process control techniques in such nonlinear, rapidly changing systems.

Jan 1, 1992

By D. R. Spears

The U.S. Bureau of Mines has had an ongoing interest in developing new reagent schemes for floating Stillwater, MT, chromite ore. Previous reagent schemes have been unsuccessful in achieving complete separation, primarily because little is known about the surface chemistry of the minerals in this ore. In order to design a rational reagent scheme, a study of the binding of various functional groups (R = -H, -OH, -CO2H, -NH2) on the two components (chromite and forsterite) of the Stillwater chromite was undertaken. Electron Paramagnetic Resonance (EPR) Spectroscopy was used to determine the adsorption isotherm, from a cyclohexane solution, of spin-probes which contained the functional group of interest. This was complemented by studies of the saturation surface coverage of the spin probe on the two minerals. In each case, more sites existed on chromite than forsterite; however, the forsterite sites were more strongly binding for each functional group. The results are discussed in terms of their implications for flotation.

Jan 1, 1994

By William Gleason

With more than 20 major mines extracting copper, gold, coal, molybdenum and lime, Arizona is recognized as one of the better mining jurisdictions, not just in the United States, but in the world. However, that is not to say the road to production is always paved with gold, or in many cases, copper. Earning the license to mine in Arizona is a complex process with years of paperwork and permitting before the first tons of ore are ever processed. Now, get the federal government involved and the process becomes even more complex, and the path to production can become even longer.

Jan 1, 2013

By Douglas J. Lacke

1974 marked the start of a new era for Climax Molybdenum Co., a division of AMAX, with the initiation of an open pit operation above the existing successful underground block panel caving mine. A number of problems posed a challenge to the Climax open pit. Highly fractured rock, old mine workings, permafrost, and more than 7.6 m/a (300") of snowfall forced changes in normal operations. Final pit wall design was altered. Production bench heights were lessened due to old workings. These and other modifications contribute to a highly successful open pit operation.

Jan 1, 1981

By M. C. Fuerstenau

Flotation data indicate that sulfonate and dodecylamine adsorb physically on Mn02 at ambient temperature. Oleate also adsorbs physically if the zero-point-of-charge of the Mn02 is sufficiently high. Chemisorption of oleate apparently occurs between pH 8 and 9, and this phenomenon is enhanced considerably at elevated temperature.

Jan 1, 1966

By D. D. Young

During the 1970's a number of covered storage facilities were constructed in North America to store and handle large quantities of bulk, solid materials. This trend, away from outdoor storage piles, will probably continue at a stronger pace in the 1980's. This paper attempts to answer some of the questions often raised about the economics of large covered storage facilities. The paper is in four parts: 1. Why Build a Storage Facility? 2. 2. Common Components of Storage Systems With Details of Six Storage Facilities 3. Results of a Study for 50,000 Mg Clinker Storage 4. Guidelines for Conducting a Study to Select a Storage System.

Jan 1, 1980

By Hugh Boyd

Jet pulverization is a relatively new tool for fine grinding. It is not yet in general use in the mining and ore dressing fields, since most of the requirements in these areas have been for relatively coarse particle sizes. As the need for finer grinding increases - because of different ores, new products, and new values being sought - jet pulverization will, increasingly, be properly used.

Jan 1, 1969

By TOMI GIORGIO DE, Ricardo Tichauer

Mineral exploration is a key factor for success in the mining industry. However, exploration best practices are often ignored in small-scale mining. This works presents the Tichauer-DeTomi Matrix, a methodology that measures the level of compliance of exploration programs in small-scale mining with the industry best practices. The matrix has been applied to three projects in Brazil: an artisanal gold mine in the state of Pará, a small-scale manganese project in the state of Bahia, and a small-scale manganese project in the state of São Paulo. The application of the matrix resulted in indexes that represent the level of maturity of the exploration program in each project and indicate priority actions for reduction of the geological uncertainty. Therefore, the Tichauer-DeTomi Matrix has shown potential to be a useful tool for assessment of geological uncertainty in small-scale mining. As a risk indicator, it may contribute to promoting investment in small-scale mining and development for communities that depend on this activity around the world.

By Paul D. Tomlingson

An effective maintenance program ensures the adequate availability of production equipment. In turn, this availability enables production to maximize utilization and successfully meet production targets. An overall production strategy is necessary to draw all departments toward this common effort. Only then will production targets be met. From the maintenance view this means that production must comply with PM and repair schedules. Purchasing must supply parts and materials on time. Mine engineering must not overwhelm maintenance with non-vital construction. Accounting must provide correct, timely cost information - - etc. This strategy - - its content, effectiveness and enforcement is the responsibility of the mine manager . . . his alone. This paper describes a successful approach to maintenance within this strategy.

Jan 1, 1979

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific, and NIOSH have combined efforts to evaluate an in-situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an Aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was pre-loaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both real-time and time-weighted-average approaches. The real-time measurements were performed with the model AE33 Aethalometer® made by Magee Scientific. The results of the NIOSH 5040 method analysis were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82%-89%. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the Aethalometer were higher, possibly due to differences in the performance of the size-selectors used for the two methods (impactors versus cyclones). More research is required to develop a robust correlation between the two methods, to support the use of the Aethalometer for future mining applications. The advantage of the Aethalometer is that it can measure and record DPM levels for weeks at a time, and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in-situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise at reducing DPM concentrations in the mine environment.

Jan 1, 2016

By George W. Parker

The ever increasing costs of labor and supplies have made it imperative that operators of open pits look for some way in which to cope with these increases. One of the most logical ways to increase the efficiency of an operation is by the introduction of larger haulage equipment, as generally haulage costs are the greater portion of the over all expenses. These larger haulage units require larger shovel units. In the late 1930's and the early 1940's large mining, quarrying and heavy construction operations had more or less standardized on the 4 to 6 cubic yard shovels. During this same period the haulage units were generally 22 to 27 tons. Some ten years ago 9 - 13 cubic yard shovels along with plus 50 ton haulage units were introduced by manufacturers in an effort to enable operators to decrease costs.

Jan 1, 1962

By Floyd L. Prestridge

A test of a solvent extraction (SX) pilot plant featuring electrostatic coalescence has been performed by C-E Natco at the United Nuclear uranium mill in Church Rock, New Mexico. Operating in parallel with the United Nuclear SX system, the C-E Natco electrostatic SX pilot plant exhibited comparable extraction efficiency to the United Nuclear system which utilizes conventional mixer-settlers. The C-E Natco pilot, however, operated at much higher liquid loading rates and exhibited less communication between the aqueous phases of the extraction and stripping circuits.

Jan 1, 1983

By G. Machiavelli, P. Bevilacqua, G. Ferrara, T. P. Meloy

During several years of operation in Europe, South Africa and other locations, the Tri-Flo process has demonstrated substantial improvements in dense-medium dynamic-separation systems. The reasons for this improvement are: • a high-sharpness separation due to the multistage system and the application of new concepts in the design of the regeneration circuit and in the control of the medium Theology, and • the possibility of performing two cuts at different densities using a single separation device and a single regeneration circuit. This paper discusses the above points in detail with particular reference to the multistage technology (based on the circuit analysis theory) and to the control of the medium rheology (based on recent work in the modeling and simulation of the rheological behavior of dense suspensions). Concerning the multidensity separation, information is given on the new three-stage separator where the high-density separation is performed by the first stage and the low-density separation is performed by the second and third stages. This configuration (already realized in two operating plants) was selected because no particular sharpness was required at the high-density separation, while high sharpness was required at the low-density separation. However, the configuration can be inverted or a fourth stage can be added (at very low additional cost) to provide two stages for each separating density. The importance of achieving a high sharpness separation is related to minerals (industrial minerals in particular) where the density difference of the phases to be separated is very low (as in processing of lithium ores, feldspar- and others). Information is provided on plants operating in South Africa and Canada, for the beneficiation of lithium minerals and on a plant under construction in Italy for the beneficiation of feldspar. Finally, the importance of making the separation at two densities is emphasized with particular reference to coal; i.e., producing a low-ash premium coal and recovering, in the middling, a by-product without losing heating value. Also, very important for some minerals is the production of a high-grade concentrate (at the first stage) suitable for sending directly to metallurgy (e.g., chromite ores) and the production of a low-grade concentrate that can be further treated. In this way, a higher overall recovery of the valuable mineral can be achieved, and, at the same time, a reduction of the treatment costs can be obtained. All of the above applications were once considered impossible.

Jan 1, 1995

By Gerry Norton

The overall economics of a coal production unit are governed by a number of interdependent parameters which individually and collectively affect the final result. A business judgement is measured through return on investment considerations and in this respect, a sensitivity analysis proves useful. Figures 1 and 2 show how the various parameters affect return on investment through unfavourable change from planned or expected values. In the case of metallurgical coals, the selling price negotiated is the primary and most sensitive variable, followed by transportation, clean coal yield and capital funds invested in mining. It is clear that coal preparation plant capital and operating costs are the least sensitive to R.O.I. For energy coals, the selling price is determined by heat energy content (x cents per million BTU's) and is therefore not con¬sidered as an interdependent variable. In this case, transportation cost is the major primary factor affecting the level of income. Again the amount of saleable clean coal or total yield has a major effect on return on investment. Most of the factors considered in Figures 1 and 2 are fixed and unfavorable change from planned values becomes critical but clean coal yield is to a great extent controllable during actual operations. Once the theoretical yield for a particular coal has been determined, the optimum return is achieved by approaching this theoretical yield as nearly as possible in practical commercial operation.

Jan 1, 1975

By C. A. Hollingsworth

The Deep Leg Flotation Cell was developed to solve a problem which confronted the Smith-Douglass Company on moving from one mining area to another. Poor recovery and, to some extent, inferior concentrate grade were encountered in the silica flota¬tion circuit. This was believed due to the softness of the phosphate which caused it to form slime. In view of the urgency of the matter, the problem was attacked from two angles. The first involved the development of a flotation cell which would not create slime and the second, a new or improved reagent for floating silica from phosphate rock which would be less sensitive to slime than reagents currently in use.

Jan 1, 1964

By Steven J. Schatzel, Kayode M. Ajayi, Marcia M. Harris, Zoheir Khademian

Predicting rockmass permeability is critical in evaluating various engineering designs, including estimating gas inflow to a longwall mine in the case of a hypothetical breach in the gas well. This study conducted field permeability measurements to validate a geomechanical model capable of predicting rockmass permeability during longwall mining. A series of slug permeability tests were conducted in an active mine in Pennsylvania. A model of the mine was constructed in 3DEC numerical modeling software, and permeabilities were calculated. The modeling results agreed well with the pre- and post-mining permeability measurements, showing the applicability of this tool to evaluate gas well stability near mine workings.

Feb 1, 2024

By Eugene C. Robertson

The exchange of heat from wall rock to ventilating air was studied in a cross-cut driven through fresh rock on the 4600 level of the Kelley Mine, Six- teen thermocouple probes, 10 inches long, twenty-three probes, 7 feet long, and five probes, 50 feet long, were emplaced in the walls soon after blasting and wall -rock temperatures were monitored intermittently over a two-year period to determine heat loss from the wall rock. Temperatures, humidity, and velocity measurements were made of the air at the same times to determine heat gain. An important but less well-defined variable was the heat transfer by water entering the crosscut from fractures and leaving in the ditch. The balance of heat in and heat out at each probe station is within an acceptable range. Theoretical and empirical models for heat flux into a cylindrical opening fit the data reasonably well, also.

Jan 1, 1970