Search Documents

By A. J. Kwitowski

Remote control for mining machines ordinarily means the operator is not seated on the machine, but is located within direct view of the machine and work area Thus, remote control operators are exposed to the hazards of roof/rib falls and dust/methane explosions. The U.S. Bureau of Mines has developed a method to disassociate remote operators from these hazards. Off-board, computer-based "tele-operational" systems are utilized that station the operators one-hundred meters or more distant from the working faces. Details are provided for tele-operated systems for thin-seam extraction and haulage equipment in highwall and deep, room-and-pillar coal mines.

Jan 1, 1992

By G. L. Mowrey

In addition to developing various types of coal interface detection systems, the U.S. Bureau of Mines is actively involved in developing a coal rib thickness monitoring system for high wall mining applications. One particular system that appears to show promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1995

By R. E. Williams

University of Idaho scientists research under U.S. Bureau of Mines Cooperative Agreement C0278001 constitutes a complex hydrogeological, hydrochemical and metallurgical mine waste management project at an existing Superfund site. Technologies that may prove useful for the extraction of dissolved metals from acid mine water and solid wastes include lixiviation and biosorption. Acid mine water is the major, long-term problem in the valley. We are attempting to delineate the major sources of ground water recharge which feed the acid mine drainage and their hydraulic properties. Grouting of recharge areas may facilitate minimizing the production of acid mine drainage if recharge pathways can be identified.

Jan 1, 1990

By J. A. Rusnak, K. M. Mohamed, M. A. Van Dyke, M. M. Sears, G. Rashed

"Researchers from the National Institute for Occupational Safety and Health (NIOSH) recently developed a coal-mass model to realistically simulate the deformation and loading behaviors of the ribs of coal pillars in underground coal mines. The scale-dependent properties (stiffness and strength) of coal material were considered in the coal-mass model. In this paper the orientation of face cleat with respect to driving direction was integrated in the coal-mass model. The controlling parameters (dimensionless coal-mass scale and fracture strains) of the modified coal-mass model were calibrated using a published case study of coal pillar strength. Numerical models with wide ranges of controlling parameters were conducted to simulate the test pillar. The best match between the numerical modeling results and the measured stresses and deformations was achieved by using a coal-mass scale of 30 and fracture plastic shear and tensile strains of 3.25% and 0.325 %, respectively. INTRODUCTION The failure of coal pillar ribs by itself are a major hazard in underground coal mines. Furthermore, failing ribs can indirectly contribute to roof and floor instability by increasing opening widths across intersections and entryways. Over the past decade, rib failures have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Mining depth has always played a very important role in assessing rib stability. Gauna and Mark (2010) completed an analysis of rib fatalities that occurred between 1996 and 2010. One of their most prominent and influential findings was the identification of a relationship among fatalities, depth, and mining height. Therefore, Coal rib stability will continue to be a challenge for future deeper mines in U.S. coal basins. In the past several decades, research efforts have focused on roof support. The current rib control practice in U.S. coal mines is to select rib bolts through a trial-and-error approach (Mohamed et al., 2015a). Rib failure incidents can be can be substantially reduced or even eliminated by adopting an engineering-based coal rib design approach. The factors affecting rib stability in coal mines are numerous and mutually dependent. These factors include but not limited to mining height and overburden depth, interburden thickness for multiple-seam mining, coal strength, cleat density, entry direction with respect to cleat orientation, existence or absence of partings in the coal, percentage of extracted roof and/or floor rock, density of rib bolt support (Mohamed et al., 2015a). Moreover, it is difficult to isolate the particular effect of a specific factor on the overall rib stability. Therefore, a reliable empirical rib design approach is not achievable because it requires a significant number of case histories to be collected in order to have a reasonable range of all of the critical parameters. However, numerical modeling can be a practical tool to assist with rib support design if the modeling is realistic, which can only be achieved through calibration and validation of the numerical model against field data."

Jan 1, 2018

By A. E. Isaacson

Researchers at the Bureau of Mines, U.S. Department of the Interior, developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were also designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1989

By Kenneth J. Miller

A novel two-stage froth flotation process to remove pyritic sulfur from fine- size coal is described. The process consists of a first-stage, standard coal flotation step in which high-ash refuse and some of the pyrite are removed as tailings. The first-stage clean coal froth concentrate is then repulped in fresh water, and a coal depressant, a pyrite collector, and a frother are added to float the remaining pyritic material. Laboratory and pilot plant flotation results with coals from the Lower Freeport and Pittsburgh beds are given. The pilot plant test results show that up to 80 percent pyritic sulfur reduction was achieved with the Lower Freeport bed coal and up to 50 percent with the Pittsburgh bed coal. Laboratory and pilot plant results were in excellent agreement, indicating that the process is a viable means of removing much of the sulfur from some coals.

Jan 1, 1974

By Jr. Schnakenberg

In 1986 the U. S. Bureau of Mines (USBM) embarked on a major research effort to develop technology that can substantially reduce worker exposure to face hazards simply by relocating the equipment operators to an area of relative safety. This reduced exposure mining system (REMS) research effort enhances the USBM ongoing health and safety research efforts to reduce and control dust and noise and to reduce accidents through training and better mining practices. This paper reports progress of the research that is developing and will demonstrate the technologies required for the computer-assisted tele-remote operation of continuous mining machines, haulage systems, and roof bolting machines.

Jan 1, 1996

By Derek J. McCracken, William G. Holroyd

Emery is a rock that at one time held a large share of the abrasives market. The introduction of synthetic abrasives, however has forced it to settle for only certain niches in the marketplace. This loss of market share is due mainly to the higher amounts of impurities and weaker internal structure that naturally occurring minerals have compared to manmade materials. The use of rocks and minerals as abrasives dates back to early man, who used flint, quartz, and other natural materials to fabricate various tools. During the 19th century, with the Industrial Revolution imminent, the character of the abrasives industry was changed forever as synthetics were introduced. Frank B. Norton is credited with producing the first manmade abrasive when, in 1855, he manufactured a vitrified grinding wheel using emery grit and clay. Before Norton's accomplishment emery had been the only commercially available abrasive. The latter part of the 20th century has seen synthetics capture an increasing share of the abrasives market from natural materials. The term emery is believed to have been derived from the words emeri (French), smeriglio (Italian), and smiris (Greek). The term corundum, for the principal mineral of emery, seems to have originated from kauruntaka, the Indian name for the mineral. GEOLOGY Emery is a gray to black, granular rock comprised of various minerals including corundum (A1,0,), an iron-bearing mineral (usually magnetite-Fe,O,, hematite-Fe,O,, or hercynite- FeAI,O,), and several trace impurities such as mullite, titania, silica, and magnesia. The hardness of emery normally ranges between 7 and 9 on the Mohs scale, depending on its mineral com- position and level of impurities. Corundum, the hardest mineral in emery, typically has a hardness of 9. The specific gravity of emery ranges from 3.2 to 4.5, also depending on mineral composition and purity. The crystallography of each mineral contained in emery differs somewhat. Corundum exhibits an hexagonal crystal structure, whereas magnetite forms within the isometric system, frequently as octahedral crystals. Hercynite, an iron spinel, is also isometric. Hematite has an hexagonal structure but often is found as botryoidal and reniform masses. Principal deposits of commerical emery are found in the United States, Turkey, and Greece. In the United States two emery producers in the Westchester County-Peekskill area and one in the Cortlandt County area of New York closed their mines in the late 1980s. Commercial production in the United States now comes only from the western Cascade Range in Oregon. The emery in New York has a typical A1,0, content of 41.5%. Most of the rock is not true emery because it contains a mixture of spinel and magnetite but very little corundum. The deposits are of Late Ordovician-Early Silurian age and consist of veins in which emery is mixed with olivine, pyroxene, and hornblende. The veins evidently were formed by contact metamorphism and are surrounded by Precambrian schists that contain mica, sillimanite, cordierite, garnet, and quartz. The deposits in Oregon were formed during Miocene time by the contact metamorphism of ferrunginous bauxite by intrusive lamprophyric dikes and plugs. Emery is found in thin layers bordering these tabular dikes, which are usually oriented perpendicular to bedding, and in "surficial placer deposits. The emery deposits in Turkey occur as small, massive, lens- shaped bodies and as surficial placers. They are believed to have formed during Permian and Triassic times. In Greece the principal site of emery production is at Cape Emeri on the Island of Naxos. These deposits consist of lenticular masses of emery surrounded by marble. They originated during Mesozoic time, evidently by metasomatic replacement. Smaller deposits on several other Aegean islands were formed by the metamorphism of bauxite or other alumina-rich materials.

Jan 1, 1994

By R. P. King

Knowledge of the behaviour of flotation machines had developed and increased considerably over the last few years. Although much work remains to be done on the study of the fundamental processes that influence the collection of hydrophobic particles at an air-water interface, there is enough information to permit the building of realistic models of the gross flotation behaviour of various ores. These models serve as an ideal base for the development of simulation techniques for the steady-state behaviour of entire flotation plants that consist of a large number of individual flotation machines. Simulation techniques have a very real role to play in assisting with the design of new plants and in improving the operation of exisiting plants. Recently, highly efficient data-logging systems have been introduced on flotation plants. These systems are based on the on-line measurement of volumetric flowrate, pulp densities, and metal contents, and they generate enormous quantities of information regarding the operation of the plant. Unfortunately, this information is largely wasted at the present time because efficient data-reduction techniques, although available10 are not in common use. Simulation techniques play a central role in such data reduction because they form the essential link between the fundamental kinetic flotation processes on the one hand and the plant data on the other.

Jan 1, 1974

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Steven T. Mitchell

The introduction of Vertical Crater Retreat (VCR) Stoping at the Homestake Mine in Lead, SD, constitutes a major advance in Homes take Mining Company's efforts to improve productivity and reduce costs through underground mine mechanization. The work to date indicates that Vertical Crater Retreat Stoping is one of the safest methods of underground hardrock mining today, and is competitive with all other forms of stoping in terms of cost and productivity. Homes take anticipates that VCR stoping rill account for approximately 30% of the total mine production in 1980.

Jan 1, 1980

By Richard Crowell, James Gillaspie

A concentrate biooxidation process was successfully demon­strated in the field in a remote part of northwestern Mexico. A 275 tonne (300 st) biooxidation heap was constructed using GeoBiotics' proprietary GEOCOAT™ coated concentrate process. The pyrite/chalcopyrite/sphalerite concentrate was bioox­idized in the heap for 60 days. Cyanide leach recovery of the con­centrate increased from 68% gold recovery at a cyanide consump­tion of 1.6 kg NaCN/g Au (llO lbs/oz) in the as-received concen­trate, to 94% gold recovery at a cyanide consumption of 0.37 kg NaCN/g Au (27 lbs/oz) in the biooxidized concentrate. The heap was constructed at a rate of7 tonnes (7.5 st) concentrate per hour, using typical heap leach equipment and easily scalable methods. Heap operations demonstrated that energy dissipation in the humid summer environment was easily controlled by low pressure aeration and management of solution chemistry and application. Observations of the demonstration heap appear to support the presence of reflux of moisture within the biooxidation heap.

Jan 1, 1998

By Staff

GENERAL DESCRIPTION The Lucky Friday mine is located in Mullan, Sho-¬shone County, Idaho. The mining method is horizontal slice cut-and-fill (with timbering for support or un¬timbered) using hydraulic sand. Cemented sand fill at a 1:17 ratio is used in sill pours and at a 1:7 ratio for the final 152 mm (6 in.) capping in successive stope floor pours. Annual production with 100% cut-and-fill mining is 167 829 t (185,000 st). The average depth of mining is 1296 m (4250 ft) and the average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size The ore body is 396 to 488 m (1300 to 1600 ft) long on strike, 1421 m (4660 ft) on dip, with an average width of 2.3 m (7.5 ft). Dip varies from vertical to1.2 rad (70°) Ground Conditions, Ore Value, and Production Requirements The ore body contains quite strong argentiferous galena and quartz. The hanging wall and footwall are strongly sheared and fractured. Ore value is $211/t ($192/st).

Jan 1, 1982

By Toshio Fujiwara, Sumikichi Ito, Masao Kitamura

The Tennohji-Benten Giant Trunk Sewer Project has been under construction since 1974 in the eastern part of Osaka, the second largest city in Japan. The entire project is divided into 7 blocks, some of which have already been completed. This 8.8-km sewer tunnel, being driven through a densely populated area, was planned to be constructed by the shield tunneling method. This paper described shield tunneling performances and ground behaviors during the construction of Blocks 2 and 3. An earth pressure shield (dia., 6,750 mm) was employed in Block 3 tunneling. The ground was generally soft and the cover over the tunnel varied from 13 m to only 4.5 m, so that a considerable amount of chemicals was injected to stabilize the ground. A hand-digging type shield (dia., 7,250 mm) was used in Block 2 tunneling under compressed air. For 85 m of the total length of 1.6 km, the soil at the face was extremely soft, and therefore, the ground freezing method was additionally employed.

Jan 1, 1981

By Vladimir J. Ovdenko, Sergey N. Lazarenko, Evgeny L. Schastlivtsev

The term sustainable development shortly appeared in international use in the run of UNO Environmental Protection Conference held in Rio de Janeim in 1992, bears the concept, that evolution process ( associated either with a region or society) should provide mutual interests concern in three aspects - environmental, economic and social ones, admitting as well the fact , that environmental protection should become an integral part of each process and cannot be regarded separately. In this connection it seems quite reasonable to employ the principal of sustainable development, while creating the model of industrial mastering the territory constraint lands viewing their future, for a example, in rich mineral deposit's development. In Kuznetsk coal basin in Russia ( west Siberia) the development of a big coal deposit Erunakovsky is now being underway. The major part of coal will be mined with open cast method, resulting the number of local environmental adverse impacts' occurrence. In such a situation mastering of sustainable development model is given the top priority, demonstrating the essential result of its application in a form of possibility to define the best correlation between economically expedient and environmentally tolerable loads during coal mining. The given paper is an attempt to work out the main principals to approach the creation of sustainable development model in regard of the definite region case. To simplify the presentation of employed approach's main idea, the given below accepts as its component only one of many actually existing environmental profiles, that define mining pro- cess impact on environmental situation -the size of infringed (de- graded) lithosphere surface. Basically, the actually existed correlation between spheres. grounding the model of sustainable development - economic, environmental and social- is given in a form of nomogram under Fig.1. On the presented graph the prognostic values of broken lands relative extent within Erunakovsky boundary ( to be compared with total region area taken as 100%) are arranged on axis x". Axis "y- demonstrates the main values associated with complete economic background, making the intrinsic part of the principal for sustainable development, i.e. annual coal output for the given area. It's top, used in assessment value relates to actual showings implied for the study region project and quantifies 60 min. tons. While regarding the social facet of principal for sustainable development, the applied mode to separate social issues into two types - one profiling a welfare standard of living and the other. pertaining the way environmental situation contributes to the degree of &ologica-1 comfort in people's living was defined as the most expedient and the most adequate in the matter of reflecting the actual terms of vital activity of the society. In accordance with the cited above the economic level showings are plotted on the graph on "-x” axis, while "-y" one obtains the values associated with the point of ecological comfort presented in conventional units. For the maximum possible conventional point of living (corresponding in nomogram to 1.0 value) a welfare level secured with industrial region economic activity revenue was assumed in case the top planned annual amount of coal is delivered ( 60 min. tons). While studying the index of public economic welfare, environmental conditions corresponding level in its original state i.e. prior to any industrial work carried in the region, was adopted as its top possible conventional rating (1.0). The given nomogram displays the integrity of x-f(y) type interrelations plotted on the basis of four separate dependencies, precisely a) the size (area) of infringed earth's surface as a function of coal output in the region; b) subordination of ecological comfort of people's living to the degree of lands infringement; c) interconnection of economic and environmental components of people living; d) interconnection of economic level of people's living and the amount of coal mined in the region. Linked to a single unit, these separate plain dependencies create, as seen from the graph, a more intricate system of bonds, that affords during defining or changing this or that system parameter to secure undergoing changes, that occur to other parameters of the system. The mentioned reason made it possible to consider and drive to mutual conformity ( as far as it is possible) all parameters values for the defined system's relations, that in their turn indicate the concern of other aspects of a sustainable development principal. According to the graph, in order to get not more than 50% of infringed land left after the deposit's mining, it is advisable to ex- tract not more than 40 min. tons of coal annually, gaining in this case the level of ecological comfort for living in the amount of not

Jan 1, 1996

By S. C. Sun

[There are significant quantities of anthracite silt deposits in Pennsylvania, known as 'liver silts" (l,2). These contain from 20 to 55 per cent of non-combustible materials, the major portion of these impurities being clay slimes. Both the anthracite coal and impurities are mostly of extremely fine particle size. The utilization of these raw silts in power-plants faces such serious problems as, handling difficulties causing plug-up in equipment, disposal of enormous ash-residue, and corrosion. These problems may be solved by upgrading the raw silt with a cleaning process, which will be capable of removing most of the clay slimes and electrolytes.]

Jan 1, 1964

By B. Weaver

Every year Pit & Quarry Magazine surveys the industry to produce their annual review. Here's a sampling of some of the statistics the survey produced from the end of the year 1994 survey.

Jan 1, 1995

By M. M. Fine

Development of a process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is underway at the Twin Cities Metallurgy Research Center, Bureau of Mines. The new route from concentrate to metal includes 2-stage fluid-bed treatment; pelletized concentrate (33 percent Cu, 7 percent S) is first desulfurized (to about 0.5 percent S) in an oxidizing atmosphere, and in the second stage the calcine is metallized by reduction with hydrogen. Thereafter, the reduced product plus 10 percent CaO is routed to a smelting furnace to separate metallic copper from the gangue. Recovery and the Cu content of the product at this point are in the 97-98 percent range. The metal must be refined to remove sulfur and iron to make wirebar copper. An important feature of the process is the pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment, which has permitted shorter reaction time, decreased dusting, and facilitated subsequent processing.

Jan 1, 1970

By Michael J. Humenick

A laboratory experimental research project was conducted to evaluate the use of chlorine for the oxidative destruction of residual ammonia which may remain in ground water after in-situ uranium solution mining operations. The work tested the idea of the injection of high strength calcium hypochlorite solution into the mining zone to convert ammonia to nitrogen gas as a final clean-up process for ammonia removal from the ground water system. The paper details ammonia removal efficiency as a function of chlorine dose, reactant and product material balances, and how the concept may be used as a final ground water restoration process.

Jan 1, 1982

By J. R. Koehler

Mining practices at the Sunnyside Mines, Sunnyside Coal Company, Sunnyside, UT, have been documented by U.S. Bureau of Mines researchers to preserve the extensive history of yield pillar-based longwall gateroad system evolution on the property. An overview of the historical mining conditions, practices, and innovations that resulted in the evolution of the two-entry yield pillar gateroad system currently employed at Sunnyside was developed from interviews of 30 long-time Sunnyside employees. Employing yielding chain pillars at Sunnyside virtually eliminates tailgate pillar bumps and contributes to reducing face bumps. Limiting the overall width of the gateroad system benefits bump control and especially, roof and floor stability.

Jan 1, 1994