Search Documents

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By B. P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using carbonate solutions. The objective of the present study was to increase the absorption rate of CO2 into the carbonate solution without reducing the absorption capacity of the solution. This approach used a polypropylene glycol methyl ether (PPGME) as a surfactant to chemically alter the gas bubble size. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations of 0, 0.12, 0.24, 0.36, and 0.48 g/L. Results showed that as the concentration of surfactant increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 mmol/min CO2 at 0g/L PPGME to 3.92 mmol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in absorption capacity of the solution.

Feb 27, 2013

By Franz Walchshofer, Mark Kuchta, Nobuharu Isago, Ugur Ozbay, Wolfgang Dolsak

A series of in situ pull test were performed on a new design friction stabilizer bolt with the objective of determining its performance characteristics. The bolt is installed while drilling, thus improving safety and significantly reducing the installation time. An optional expansion element can be inserted into the bolt to provide an end-anchorage, which further increases the bolt’s capacity. In situ tests show that the pull capacity of the 2 m long new design bolt is about 15 tons. When installed with an expansion element, the pull capacity of these bolts becomes as high as 30 tons.

Jan 1, 2005

By O. P. Burghardt

Blast furnaces of high specific throughput capacities producing 10,000 tpd of pig iron or even more, require burden materials which, because of their chemical, physical and metallurgical properties, guarantee such high performances. Meanwhile, it should be generally accepted that for evaluating the quality of iron ore pellets, it is not sufficient to know the chemical analysis and the physical properties, i.e. grain size distribution, cold compression strength and abrasion of the fired pellets. It is indispensable to determine the metallurgical properties indicated by swelling, reduction-softening under load and reducibility, as well as grain disintegration in the low-temperature range in the beginning of reduction. By introducing new test methods, and in the face of the need to meet more strict requirements, pellet producers are being confronted with steadily increasing tasks and problems which require a deepening of our knowledge of the ways and means of making high-quality iron ore pellets.

Jan 1, 1975

By J. O. Voigt

No major changes took place in the salt industry during 2004. No new uses of salt appeared and only localized supply disruptions occurred. Many salt producers reported slightly increased salt sales and profits for the year. In the United States, about half of the salt supply is produced as brine, by solution mining, and is used by the chemicals industry. One-third of U.S. salt is produced as rock salt by 14 underground mines. The remaining two production techniques, each with less than 10 percent of the total tonnage, are vacuum-pan-evaporation for refined, food-grade salt, and solar pond crystallized salt.

Jan 1, 2005

By David R. Gossett

For the 22nd year, the chance to exchange knowledge, experience and business cards drew hundreds of mining and phosphate professionals for a two-day regional Phosphate Conference in Lakeland, Florida Nearly 400 people participated in the October conference, which focused on the phosphate industry?s future success. There were 41 exhibitors, 13 program advertisers and 23 sponsors among those supporting the conference. It was chaired by David Gossett, 2006-2007 SME Florida Section Chairman. In the opening panel session that he chaired, John Garlanger (SME) of Ardaman and Associates posed the questions; ?How successful has the industry been? How do we measure it and what factors contributed to the industry?s success? How long will the ethanol boom last? Can the industry obtain the permits it needs to mine for the next 30 years? Can the industry attract and retain the quality of workers it needs??

Jan 1, 2008

By Clay Haynes

While the Kansas River Tunnel is a relatively short, small diameter tunnel, the shaft excavation methods implemented were long and large on innovation and use of reverse circulation drilling equipment. ATS Drilling, L.P. used mechanical excavation techniques for both soil and rock segments of the 42.7 m (140 feet) and 38.1 m (125 feet) deep shafts that were 2.9 m (9.5 feet) and 4.1m (13.5 feet) diameter, respectively.

By Jose F. T. Agapito

The mining engineer must be able to predict the structural behavior of the rock around underground openings so that he can answer questions relating to safety and economics. With the present status of rock mechanics knowledge, exact predictions cannot be attained and approximate idealizations are made. As a first approximation, structural design makes use of theory, laboratory testing of rock properties, and available experience from excavations in similar rock formations. However, realistic design can usually be obtained only after in-situ observations and measurements are made. After all the information is collected, judgement and experience play a most important role in the final formulation of the design. This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator, The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale, The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver (Figure 1) . Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River Formation at a depth of 600 to 850 ft, Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek, The distance from the mine to the side of the mountain varies from 500 to 1,200 ft, and its height above the stream floor is approximately 700 ft.

Jan 1, 1974

By Z. Duan

A novel concept involving the deployment of chemical stabilization has the potential to eliminate the need of slurry impoundments and significantly reduce the release of trace elements from the high surface area fine coal waste. The process involves mixing the fine waste generated from the underflow of a thickener operation with chemical stabilization agents to tie up the water and to create a solid waste material that can be discharged directly. Portland cement, sodium silicate, F type flyash, C type flyash and hydraulic lime were evaluated as stabilizing agents. A detailed experimental study has been conducted to identify the conditions that provide the maximum compressive strength within a short curing time. Results to date show the ability to achieve compressive strengths adequate for equipment to maneuver on using a Portland cement concentration of around 10% by weight. Quick-setting concrete was not found to enhance stabilization time and compressive strength.

Jan 1, 2012

By A. D. Davis

The former Homestake gold mine at Lead, South Dakota, has been selected by the National Science Foundation as the proposed host site for the Deep Underground Science and Engineering Laboratory. The deep laboratory and associated research campus will be developed at approximately the 7700-ft level. Plans also include the development of the Sanford Underground Science and Engineering Laboratory at the 4850-ft level. After the mine?s pumps were shut off in June, 2003, water levels rose to approximately the 4650-ft level by early 2008. Pumps in the 8150-ft deep mine were turned on again for dewatering in April, 2008. Instrumentation is being installed in the mine to measure water-level declines during pumping, for later analysis of permeability and related hydraulic properties of the formation. Pressure-sensitive transducers and data loggers will provide real-time information on water levels that will be available to interested parties. Quality of the water also will be monitored as it is pumped from the mine. I

Jan 1, 2009

By Stephen Hodgson, Ken Brouwer

September 2005, Northern Dynasty Mines announced the discovery of a new, high-grade deposit at its Pebble project in southwest Alaska. The product of insightful geological investigation, Pebble East, as it is now known, is quickly growing into one of the most significant copper deposits in the world. Preliminary analysis shows it could reduce the U.S. copper supply deficit by a third. The new deposit has also altered Northern Dynasty’s view of how Pebble should be developed. This article describes the Pebble project as it is currently understood and outlines the work planned for the next several years.

Jan 1, 2007

By L. John Minnick

Extraction of crude ores and minerals inevitably produces various by-products either as a result of nonusable residues or as waste by-products from process operations. Thus for each 100 tons of coal extracted in a strip mine operation, one can expect to produce 25 tons, or more, of mine refuse. In addition, the amount of ash produced from the burning of coal will represent 10 to 20 percent of the weight of coal burned. With the advent of lime/limestone scrubbers now being installed on many power plants, an additional by-product is produced that in most instances is equal in volume to the sluiced fly ash. Statistics developed by the National Ash Association have indicated that sluiced waste from power plants in the United States currently exceeds 25 million tons per year (dry basis). Overall mineral industry statistics (copper mines, etc.) indicate better than 200 million tons per year. In the past it was general practice to send most of these waste materials to holding ponds or lagoons simply as a means of disposal or "throwaway" of unwanted by-products. Unfortunately modern society has reached a stage where these large quantities of waste materials are creating monumental environmental and economic problems that need urgent attention. Among these problems are concern for loss of future usable land, pollution of ground water, loss of potential mineral reserves, and loss of opportunities to recycle or use these by-products for the benefit of future generations. An example of the latter is the serious shortages of construction quality aggregates that can be replaced with some of the by-products produced from waste materials from the extractive and chemical industries.

Jan 1, 1975

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By M. Javier

Mining is an industry of experimentation throughout human history. Recently, societies are giving a clear message about mining because many projects are being rejected around the world. These refusals are a generational reaction to the activity of mining. In practice, it generates the perception that mining is using the same methodology without attending to the gradual initiation of conflicts. This is in spite of the best engineering and technology of the time that are put in place at the presentation of those mining projects. Some of these rejected projects are geographically distant from each other, but the communities? rejection occurred during many cases under similar characteristics. This concern shows that the current model of mining projects needs to be replaced with a new one: A new Design, one within which the socio-environmental values of this millennium are inherent. This paper describes Mining Project 101 to help the industry to set the highest and cleanest standards for mining. It also presents its aspects to sustainability and nature, which provides the principles and procedures for designing, planning, and operating mining projects with sensitivity to nature. It offers methods of diagnostic, remediation, and extraction while at the same time preventing and preserving a physical, chemical, and biological equilibrium of nature. This emerging process will be a step up from having a mining industry unaccountable to the socio-environmental conflicts it perpetrates and will abandon the ?cosmetic? repair on the caducity of traditional models in today?s practice. In conclusion, we have the opportunity to change this model. KEYWORDS: Equilibrium in Nature, Geomímic, Deproduction, mine design.

Feb 27, 2013

By G. A. Gamble

Fans used to ventilate subway, passenger rail and vehicular tunnels are similar to the fans used to ventilate underground mines. However, tunnel ventilation fan systems are typically designed to meet NFPA 130 or 502 standards, while mine ventilation fan systems must comply with the appropriate federal mine safety regulations. As a result, fan operation requirements and performance criteria, as well as typical fan and duct configurations differ significantly for tunnel and mine ventilation applications. Variations in environmental conditions in tunnels as compared to mines also result in differences in fan performance and material specifications. The need to enclose tunnel fans within building structures creates space restrictions impacting fan size selection that are not commonly encountered in mine fan installations, resulting in different approaches to selecting fans for the two types of tunnels. This paper discusses the various similarities and differences in design considerations for tunnel and mine ventilation fans.

Jan 1, 2009

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009

The use of belt air in underground coal mines has been a continuous discussion since it was first introduced in the Federal Coal Mine Health and Safety Act (Coal Act) of 1969. Although the Coal Act prohibits the use of belt air to ventilate active workings, there were two exceptions prior to the 2004 Final Rule. There have been several major studies/rule-proposals by MSHA since 1985 and the most recent of which is the Technical Study Panel (TSP) established by the Mine Improvement and New Emergency Response (MINER) Act of 2006 to study the use of belt air and related issues. This paper reviews the history of belt air use, its associated controver-sies, and more specifically, the 20 recommendations unanimously approved by the TSP.

Jan 1, 2009

By A. Redman

Aquatic organisms are sensitive to free cyanide (HCN) though the presence of certain metals that can form stable complexes and thereby reducing both the amount of bioavailable cyanide. Recent work has suggested that consideration of HCN rather than total cyanide can provide the basis for water quality criteria. Cyanide is often present in complex effluents that affect speciation and bioavailability. We have developed a model to predict the speciation of cyanide in complex effluents and have shown that this model can predict the toxicity of metal-cyanide complexes in terms of HCN. This study evaluated available cyanide toxicity exposures with this model to assess the role of water chemistry (e.g., metal-cyanide interactions) on the observed. Toxicity endpoints based on total cyanide ranged over several orders of magnitude for a variety of metal-cyanide mixtures. However, predicted HCN concentrations among these same tests described the observed toxicity data to within a factor of 2. Aquatic toxicity can be well described using HCN though in certain metal-cyanide mixtures toxicity was jointly described by HCN and elevated levels of bioavailable metals. This work was performed in support of an industry-sponsored reassessment (Gensemer et al 2006) of the U.S. EPA water quality criteria for cyanide (EPA 1985) using free cyanide as the basis for the re-calculation. The work presented in this manuscript presents technical support for using free cyanide as the preferred basis for this recalculation.

Jan 1, 2011

By J. F. Allan

The main conditions which affect investment in mineral exploration and development are compared in five countries currently considered attractive for mineral investment - Canada, the U.S., Australia, Brazil and the Philippines. The primary parameters - the probability of occurrence and discovery of mineral deposits and the short and long term viability of mineral development - are evaluated and compared on a relative basis by a form of factor analysis. This analysis indicates that of the five countries studied, Canada is second only to the United States in degree of favourability for mineral exploration and development.

Jan 1, 1976

By Paul H. Johnson

The CH Leaching process is a new, more sophisticated, form of gold, silver, uranium and sulfide copper heap leaching wherein each layer of a multi-layered heap is divided into a number of independent cells, each of which are successively formed and leached in the top layer of the heap to their maximum economic recoveries, and then rinsed and sealed from further leaching. Triangular earth berms form the outside walls of the heap and a gridwork of rock-filled berms on top of the bottom pad form independent under- heap solution storage zones. The high degree of solution recirculation and staging that occurs in this process produces a relatively small volume of very rich pregnant solution. The cellular heap design and its mode of operation result in a uniform, intensive, long-term leach for all of the ore particles in the heap. Besides improved metal recoveries, the process appears to have several cost and operating advantages. In the CR2MR process, sulfuric acid and a soluble sulfide are added to a gold and/or silver pregnant leach liquor to precipitate most of the contained silver, mercury, copper, etc. as sulfides at a pH below 2.5. The other product of the reaction is solubilized HCN. Following a liquid-solid separation step, cyanide is regenerated in the supernatant solution by raising the pH to a level above 9.0. This process regenerates a portion of the cyanide used in the leaching step, removes contaminant ion species (silver, copper, mercury, etc.) from the leach solution and, in a subsequent step, recovers the gold in an enriched form. It is believed that substantial cost savings may be experienced by the use of this process in some gold and/or silver leach systems.

Jan 1, 1984