Search Documents

By Carl G. Consalus

The Kemmerer Coal Company's Sorensen Mine is located approximately 7 miles Southwest of the Town of Kemmerer, Lincoln County, Wyoming. The coal it produces is delivered via conveyor directly to Utah Power and Light's Naughton Steam Generating Plant. The Plant went on the line in the spring of 1963 and the Sorensen Mine has been producing coal since February of that year. In this period, approximately 2, 000, 000 tons of coal have been delivered to the Plant. Present Sorensen mining operations are being carried out in the upper seams of the Adaville Formation. The formation contains, in some places, up to 30 coal seams of varying quality and thickness. Thirteen seams are considered major and are given numbers; the rest are considered splits off of the major seams and are so named. The lowest seam stratigraphically is the No. 1, or Elkol seam. So far, it has not been committed to power production but is being held in- reserve. It is the thickest seam with 80-90 feet of coal as its average thickness. The other major seams vary from 10-50 feet thick, with most of the seams averaging 17-26 feet of thickness. Each major seam has been opened at least once' to obtain a true gross sample of the coal's performance in the Plant.

Jan 1, 1967

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By R. Herrera-Urbina

Measurements of the electrophoretic mobility of bastnaesite in aqueous solutions of sodium nitrate reveal that the isoelectric point (iep) of this cerium fluocarbonate occurs at about pH 9.3. These results also indicate that the pH affects significantly the electrophoretic mobility of bastnaesite, which becomes more positive as the pH decreases and more negative as the pH increases from the iep. Computations of solid-solution equilibria for the bastnaesite-H2O system closed to the atmosphere as a function of pH indicate that cerium fluoride precipitates in acidic solutions, whereas cerium hydroxide precipitates in alkaline solutions. When the initial amount of bastnaesite is fixed at 0.05 wt.% (the solids concentration used for electrokinetic experiments), these computations reveal that bastnaesite is the only solid phase in the pH range from 5.75 to 8.55, it coexists with CeF3(s) between pH 5.22 and pH 5.74, and with Ce(OH)3(s) between pH 8.56 and pH 10.12. Cerium fluoride and cerium hydroxide are the only solid phase below pH 5.2 and above pH 10.2, respectively. According to these computations, the dissolution-precipitation processes that occur when bastnaesite is equilibrated in aqueous solutions at different pH values determine the solid phases present in the system. In turn, these processes must affect the electrokinetic potential at the solid-solution interface, and they must be considered for explaining electrokinetic measurements as a function of pH when bastnaesite is the original solid phase in aqueous suspensions.

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world's major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program's use and interpretation of its results will conclude the paper.

Jan 1, 1984

By Lloyd M. English

Accurate knowledge of the gas content of coal seams has always been important, according to the work of W. P. Diamond and J. R. Levine, 1981, but is becoming increasingly important for several reasons: Excessive gas emissions in the mine can create explosion hazards. Depletion of shallower coal reserves is forcing underground operations to greater depths where coal gas content is often greater. Natural gas prices and the need for new energy sources make naturally occurring coal gas a potential resource of economic interest. Information on coal gas content will impact mine designs, mine ventilation system specifications, and the effectiveness of methane control procedures used. Accurate resource assessment is needed for projecting and designing potential gas utilization enterprises. The emphasis upon methane hazards in mining operations, and upon potential methane utilization, has led us to improve upon the procedures used to determine coalbed methane levels.

Jan 1, 1984

By Y. A. Attia, M. Elzeky

Thiobacillus ferrooxidans bacteria were used in this work to study the effect of bacterial adaptation on the bioleaching of three iron-bearing sulfide minerals, namely, pyrite, chalcopyrite and arsenopyrite. The change in the pH during the bioleaching process was observed and the mechanism of the bacterial action were discussed. It was found that bacterial adaptation prior to bioleaching, enhanced the degree of sulfide leaching by 2-4 folds over that of non-adapted bacteria. A1 so the bacterial activity was enhanced by 2-4.8 folds. The pH of leaching solutions was decreased by the increase in both adaptation period and bioleaching time. It was also concluded that the mechanisms of bioleaching of iron-bearing sulfide minerals involved both the direct and indirect bacterial action simultaneously.

Jan 1, 1989

By Gerald M. Ellis

ntroduction As the gold mining industry continues to develop in the Dominican Republic and Haiti, more deposits will undoubtedly be discovered that will be amenable to development. The Pueblo Viejo gold mine is currently in operation in the Dominican Republic. It has become an important component of that country's economy. Pueblo Viejo output is important to the government as a foreign currency earner. It is also said to be among the world's more successful gold mines. But, while Pueblo Viejo is successful, no other major gold discoveries have been made in recent years. Therefore, alluvial deposits of gold have caught the attention of geologists on the Island of Hispaniola. In the past four years, exploration and investigation of alluvial deposits have been initiated in both the Dominican Republic and Haiti. This type of activity is expected to continue over the next few years. Alluvial gold mining is rudimentary gold washing, done mostly by farmers. It is an old tradition, dating back at least 100 years, and is done by small, independent, or community farming villages in the mountains and plains of the Dominican Republic. Investigations in the DR Recently, alluvial gold investigations have been undertaken in well known locations of the Dominican Republic. One is in the Villa Altagracia area. Here, the terraces and gravels of the Haina River basin were examined, test-pitted, and assayed by Minera Altagracia, a local Dominican mining group. Results led to a new investigation by the state-owned Rosario Dominicana (RD), the company that mines the gold at Pueblo Viejo. Rosario tested areas previously investigated by Minera Altagracia. RD could not define the type of concentration that could justify an industrial-scale type of exploitation. The Haina River placers are located in the flats and valleys of Central Dominican Republic. They are classified as small-scale type of operations where local cooperatives can do the traditional gold washing. It is not now considered a dredgable project for a mining company. The next alluvial gold investigation was undertaken by the Dominican Department of Mines and others in an area of some 700 km2 (270 sq miles) in the northeast near Miches. Farmers have been washing gold in streams and excavating pits in various areas, particularly La Mina and have made a living. Government geologists panned several hundred streams and river tributaries. They also washed material from deep excavations. The results, however, were negative insofar as locating alluvial gold concentrations suitable for large-scale or industrial-scale exploitation. The most favorable locations were the terraces along the Jayán and Cuarón Rivers in the area of Miches. But the grade od concentration is poor. Actually, only traces of gold were found in these

Jan 8, 1986

By Verya Nasri

This paper presents analysis of damages and rehabilitation design for three major French rail-way tunnels built in mid-19th century. The La Nerthe tunnel underwent ovalization deformation with excessive displacement at the springline, and pinching and bursting of the liner bricks at the crown due to tectonic residual stresses with very high lateral earth pressure. The Saint-Louis les Aygalades tunnel invert was subjected to undulatory deformation resulting in tracks misalignment, which was caused by non-homogeneity of mechanical and hydraulic properties of the ground. The Roches de Condrieu tunnel required widening to comply with the increase in dynamic envelope of trains due to their larger cross section and higher speed. The applied rehabilitation methods and constraints of work in these busy mainline railway tunnels have been discussed in detail.

Jan 1, 2008

By Georgene Renner, William R. Yernberg, Steve Kral

Agapito Associates (AAI) provides consulting services in geo-engineering, mining engineering and related disciplines. Founded in 1978, the firm operates out of offices in Grand Junction, CO, Golden, CO and Lombard, IL. Members of the staff include mining, civil and geological engineers, physicists, geologists, numerical analysts, computer specialists, instrumentation specialists, plus administration and technical support personnel. AAI has provided consulting and engineering services to mining companies producing base metals, precious metals, coal, potash, trona, limestone, oil shale and salt, and to defense and nuclear-waste disposal industries. AAI also provides services for measuring in situ horizontal stresses using an advanced biaxial overcore stress downhole measurement system developed by Sigra of Australia. Since 1978, AAI has measured in situ stress in copper, oil shale, molybdenum, trona, limestone and coal mines, and in tunnels and concrete structures. Since 1994, the staff has completed 527 overcore stress determinations. AAI has the equipment and personnel for overcoring, sample coring and instrumentation installation in limited access, surface and underground mines. Portable Longyear CP-65 drills, borehole deformation gauges and strain indicators are used for difficult-access overcoring and are permissible for use in gassy mines.

Jan 1, 2006

By Jerry C. Tien

Without a doubt, the scope of China?s coal boom has been nonstop. Despite the world economic slowdown, China?s year-on-year gross domestic product (GDP) jumped 10.3 percent year-on-year in 2010, boosted by a faster than expected 9.8 percent expansion in the fourth [ ] quarter. And, the first quarter of 2011 expanded another 9.7 percent. According to a frequently cited statistic, the country is building two mid-sized coal plants each week. This amounts to a yearly increase equivalent to the entire power grid in the United Kingdom. China?s coal production was doubled in the last 10 years, from 1.044 Gt (1.15 billion st) in 1999 to 3.2 Gt (3.52 billion st) in 2010. This is 3.2 times the U.S. production (986 Mt or 1.085 billion st) and nearly half (46.3 percent) of the world?s total coal production (6.91 Gt or 7.6 billion st). This rapid increase of demand for coal has made China the world?s largest coal importer in 2009. With the economic situation improving, this trend is expected to continue.

Jan 1, 2011

By H. Copur

Roadheaders have become widely used in underground mining and tunneling operations because they offer the flexibility to excavate soft- to medium-strength rock formations. A critical issue in successful roadheader application is the ability to develop accurate and reliable estimates of machine production capacity and the associated bit costs. Increased pressure to improve productivity and lower costs in the mining and civil construction industries has been the driving force behind the more wide- spread use of mechanical excavation systems. This has caused both industries to move away from the conventional drill and blast methods. Additional benefits of mechanical mining include improved safety, reduced ground support requirements and fewer personnel. These advantages, coupled with recent enhancements in machine performance and reliability, have resulted in mechanical miners taking a larger share of the rock excavation market. Roadheaders are the most widely used underground partial-face excavation machines for soft- to medium- strength rocks, particularly for sedimentary rocks. They are used for development and production in soft rock mining (main haulage drifts, roadways and crosscuts), particularly in coal, industrial minerals and evaporitic rocks. In civil construction, roadheaders are used to excavate railways, roadways, and sewer and diversion tunnels in soft ground conditions. They are also used to enlarge and rehabilitate underground structures. Their ability to excavate almost any profile opening also makes them attractive to those mining and civil construction projects where various opening sizes and profiles are needed. In addition to their high mobility and versatility roadheaders are generally low capital cost systems com- pared with most other mechanical excavators. Because of higher cutting-power density due to a smaller cutting drum, roadheaders can excavate rocks harder and more abrasive than continuous miners and borers.

Jan 1, 1998

By Hans Janzon, Ernst Buechi

INTRODUCTION The headrace tunnel in Amlach is part of a hydro electric power scheme near the city of Lienz in south west Austria. The project is owned and developed by Tiroler Wasserkraftwerke AG, the regional electrical supply utility. The construction work was divided into seven contracts for the entire scheme. The power output will be 60 MW, this being developed from a head of 370 m and water flows of 20 m3/s. The water will be tapped from the river Drau and lead through a 22 km long headrace on the south side of the Puster valley through the Lienzer Dolomiten mountain range. Contract No. 4, which is a joint venture between Mayreder, Züblin, Strabag, Rella and Innerebner, involves the construction of 13.5 km of the headrace. It was decided to bore this from one single adit, which probably makes it the longest pressure tunnel driven from one side by a TBM. (See Fig. 1.) For the tunnelling an Atlas Copco Jarva MK 12 TBM was chosen. The excavation diameter is 3.90 m, with the final lined diameter being in the range of 3.20 to 3.40 m. The back-up is a 145 m long single track rail system supplied by Mühlhäuser (Germany). Side-tipping cars with a capacity each of 8.2 m were used for removing the muck. One California switch was attached to the back-up after 3,000 m, and a second fixed switch was installed after 8,000 m of boring. 3 m long

Jan 1, 1987

By R. J. Boyd

SUMMARY The productivity of drill and blast methods of mining in hard rock is limited by the cyclic nature of the operation, and a plateau of performance has been reached, even with the most advanced equipment developments. Higher mine operating costs and lower metal prices have more than ever generated the need for breaking through these productivity barriers. After initial field testing The Robbins Company has designed and manufactured, on a joint venture basis with Mount Isa Mines, Ltd., Australia, a prototype "Mobile Miner" for continuous cutting of hard rock. This paper describes the cutting concept, the initial application of a completed 1,156 m (3792 ft.) long 14% decline, actual performance and delay analysis, developmental modifications, anticipated performances of a fully developed machine, and possible future applications. Sincere appreciation is expressed to the management of Mount Isa Mines, Ltd., for allowing access to the data used in this paper. The views expressed here are those of the author and not necessarily those of Mount Isa Mines, Ltd. INTRODUCTION A paper titled, "Design and Development of a Mobile Mining Machine", was presented by J.P. Kindsvater at the RETC, New York, in 1985. This paper described the evaluation of a test fixture in an andesite quarry near Seattle, followed by design, construction and

Jan 1, 1987

By Howard L. Hartman

Pardon my audacity, but I feel that this is the solution, not just a solution. Further, I will be so bold as to maintain that this is the last-ditch, eleventh-hour chance for the mineral industry to solve its critical technical manpower shortage. I am not being facetious. I am convinced that there is only one solution--just as there is but one real cause of the problem. My conclusion 'is reinforced by countless talks of endless hours with people both in and out of the industry, with employers and employees, and with educators and students. While I claim no originality for the idea and have no pride of authorship, I am concerned that the industry hear and heed in time. It is quite unlikely that the mineral industry and the mineral engineering profession will willingly subscribe to my thesis or gladly buy my proposal. I am convinced, however, that it is the only course of action open to us, and the only course of action which will succeed.

Jan 1, 1967

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through the use of more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the air bubbles, water, and ore, rapidly attaching the hydrophobic mineral to the bubble surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. A rougher concentrate containing 4.5 pct copper was obtained from a western porphyry copper ore containing 0.67 pct copper. Over 99 pct copper was recovered from the ore at a rate 7 times faster than conventional flotation.

Jan 1, 1991

By J. E. Shearer

The state of Arizona produced 253,276.2 metric tons (279,000 st) of crude gypsum during 1986. This represents approximately 1.7% of the total U.S. production. Four mines provided Arizona's gypsum, three of these mines are in the San Pedro Valley. The uses of the gypsum produced in Arizona are for manufacture of cement, agricultural uses, and wallboard manufacture. The gypsum is used as a retarder in the manufacture of Portland cement. The use in agriculture is treatment of alkali soils to allow water penetration. Other deposits in the San Pedro Valley have production potential, providing there is sufficient market for additional wallboard. The author completed an evaluation of one property earlier this year.

Jan 1, 1988

By Colin D. Jardine

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. A recent application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by the use of a "building block" approach to design and equipment selection. Details of this approach and the results obtained are described.

Jan 1, 1982