Search Documents

By P. Mousset-Jones

The USBH Mining Systems and Ground Control Generic Research Center funded a project leading to the improved planning of airflow and refrigeration in underground mines experiencing hot working conditions. The project was broken down into approximately five phases: 1. Visiting some of the known hot mines in the U.S. and sending out a questionnaire to determine other mines which might be experiencing hot working conditions in the future. 2. Choosing two mines in which to conduct measurements to determine the insitu rock thermal conductivity and diffusivity, and comparing these values with laboratory determined values. 3. Investigating computer programs available for mine climate simulation, and testing these programs with case study examples from the two mines where the rock thermal properties were measured. 4. Considering improved ways of estimating the wetness factor and experimenting with the use of heat flux meters to more directly measure the rock heat inflow into the airstream. 5. Applying the results of these investigations to simulating the climate for future mine development and production areas at the two- mines. The project is approximately two thirds completed. At the time of writing, the insitu measurements at one of the mines are still being recorded. This paper will be describing the procedures and results of the insitu rock thermal property measurements, and give a brief description of some of the simulated results obtained for a mechanised cut and fill stope case study from the Homestake Gold Hine in South Dakota.

Jan 1, 1985

By Jonisha P. Pollard, F. Nasarwanji, Lydia M. Kocher

This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1000 full-time employees, which is nearly double the rate of the next highest affected body part, the back.

Feb 24, 2022

By Kerry Spickelmier

The only nickel smelter and the only active nickel mine in the United States is Glenbrook Nickel Co., a joint venture (50% each) of Cominco Resources International Ltd. and Cominco Ltd. In 1989, with the nickel price riding high between $2.30 and $2.70/kg ($5 and $6/lb), Glenbrook seized the opportunity to purchase and recommission a southwestern Oregon ferronickel smelter and the adjacent nickel-ore mine. This Douglas County site is only about 97 km (60 miles) due east of the Pacific Ocean, and California's border lies a similar distance to the south. Hanna Mining Co. had closed the operation in 1987. And the following year, the equipment had been largely stripped for salvage value. From November 1990 through August 1992, the mine supplied an average 5 kt/d (5500 wet stpd) of ore. Currently, with import ore supplying 40% of the smelter feed, the mine's daily tonnage averages 4.2 kt (4600 wet st). From November 1990 through August 1993, the mine has delivered 2.1 Mt (2.3 million st) of ore grading 1.22% nickel with an average moisture content of 26%. Buffaloed nickel? A nickel is not worth what it was in 1989 and neither is ferronickel, with recent prices hovering around $1.13/kg ($2.50/lb). To survive, Glenbrook has focused on increasing smelter production to lower its operating costs. And this strategy has triggered several bold moves: • a new, $30 million, port facility and • a 10-year importation contract for ore from New Caledonia, an island approximately 1000 km (625 miles) east of Australia. For a Glenbrook update, a May 25, 1993 visit was made to the company's Oregon operations - the mine and smelter near Riddle plus its new Coos Bay port facility. Unfortunately, as the rain came down that day, so did news of another temporary shutdown. The previous suspension had lasted from Dec. 20, 1992 until Feb. 22, 1993. Barely three months back to work on a wet May afternoon, more than 250 of Glenbrook's approximately 300 employees contemplated yet another shutdown, effective July 31, 1993.

Jan 1, 1993

By Sabina Brady

Investment in the ferrous sector between 1981 and 1985 will total about $9 billion, or 7.6% of the state budget for capital assets. The money will primarily go to complete the first stage of the Baoshan Iron and Steel complex and to increase steel production by 3 Mt* (3.3 million st) and seamless tubing by 0.5 Mt (551,000 st). Investment in 1983 will be about $3.5 billion, a 28% increase over 1981. Although data on nonferrous investment is less specific, the Chinese announced early this spring that the country's investment would be 2.6 times greater than the average spent during the previous five year plans. Geological surveying will also be stepped up. The Ministry of Geology and Minerals recently announced it will incorporate a search for metal and mineral resources into its second round of oil and gas surveys. The Sixth Five-Year Plan desig¬nates some actual production targets. Steel is to increase to more than 72 Mt (79.4 million st). The country's production of 10 priority nonferrous metals - aluminum (and bauxite), copper, lead, zinc, nickel, tin, antimony, mercury, magnesium, and titanium - is to increase 12.7%. Top priority is to develop aluminum production. Renewed efforts are to be made to develop gold and silver production and to increase rare earth and rare metal production. By April 1983 when the China Nonferrous Metal Industry Corp. was established, some five months after publication of the Five-Year Plan, the goals for nonferrous development had already been upgraded and changed to include: • development priority status equal to that of coal's; • an increase of more than 150% in the 1985 projected production level for the 10 top nonferrous metals (a move from the Sixth Five-year Plan's production increase of 12.7% to one of 34%); and • modification of the top 10 nonferrous metals list to include tungsten, molybdenum, and rare earths. Aluminum, copper, lead, and zinc maintained primary importance, while mercury, magnesium, and titanium were deleted. It is likely that the modification will be taken one step further and titanium will be substituted for antimony. China has already indicated its intentions to stabilize rather than expand its antimony industry, while press reports play up the titanium industry's importance to the country's development. In addition, the China Nonferrous Metal Industry Corp. announced that it expects to register a progressive annual increase of 4% in foreign currency earnings through export. China's nonferrous development efforts, therefore, appear two-pronged. First, the country's efforts will be directed toward self-sufficiency in its four major process and primary metals - aluminum, copper, zinc, and lead - and a number of other nonferrous metals that are in increasing demand by its light industry sector. At present, 96% of China's non¬ferrous consumption is composed of aluminum, copper, lead, and zinc. Substantial portions of that must be imported to meet rising demand. Second, efforts will concentrate on those metals that can be developed the fastest and are in "urgent demand" on the international market. Metals such as tungsten, tin, molybdenum, titanium, nickel, and rare earths will be given freer use of foreign capital and technology to increase production levels and raise quality. Examples of some projects in the area include upgrading the country's carbide industry and developing new high speed and tool steels to meet international standards. Foreign involvement and sales have been reported in each area, particularly with regard to sales of deposition equipment and presses by Swiss and West Ger-

Jan 8, 1983

By P. Koh

A novel approach incorporating computational fluid dynamics (CFD) and flotation modelling has been used for investigating flotation cell designs. CFD modelling has increasingly been employed to enhance understanding of the cell hydrodynamics in mineral and coal flotation. Opportunities for improving the flotation cell performance can be identify by modelling. The CFD-flotation model from CSIRO incorporates cell hydrodynamics that affect particle-bubble interactions. Information from the model includes velocities, turbulent dissipation rates, gas hold-up, particle-bubble attachment and detachment rates. The attachment and detachment rates have been found to be effective measures of cell performance for cell design.

Jan 1, 2011

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

A viable mineral economy requires availability of economic deposits, the ability to exploit then, and protection of the public interests. The natural tendency for each party to consider only its legitimate self interests can lead to delays or deadlocks. The paper presents several viewpoints aimed at opening each party's mind to the ideas of others in the hope that negotiations might be more reasonable and rapid for the benefit of all concerned.

Jan 1, 1979

By F. M. Jenkins

Improvements in miners? safety and health, as reflected by injury and illness statistics, have reached a plateau and even been reversed. Research into miners' OSH is a necessary adjunct to regulatory enforcement. Under the National Occupational Research Agenda (NORA) mining experts have come together to draft a national agenda for this research. The Mining Sector Council, one of ten NORA Sector Councils, has produced a draft national research agenda to guide all mining research entities: academia, government, and industry. The agenda has seven major objectives, each of which has a sequence of sub-objectives: Reduce the likelihood of disasters in mines; Improve mine disaster response; Improve the health of miners; Improve atmospheric control (ventilation) in mines; Improve health and safety through behavioral research; Improve mine design, systems operations, and management performance to enhance mine health and safety; Apply ergonomics, human factor engineering, to increase health and safety. Long-term maintenance of the Mining Research Agenda requires input from the public, both here and abroad, monitoring of the impact of research results using OSH data, and partners who will translate the research to practice.

Jan 1, 2012

By Jalal Vakili

In designing very large excavated slopes which are becoming increasingly common in both mining and civil engineering projects, the most important decision of the engineer is the selection of a slope angle. The purpose of the geotechnical study of the slope is to ensure reasonable stability of the slope in the most economical way. Because the rock mass composing each slope is unique, there are no standard solutions for slope stability analysis. A practical solution is formulated from the basic geologic data, engineering properties of the rock, geometry of the slope, and ground water observations. Stability analysis consists of analyzing the forces causing and resisting slope failure. There are several methods of slope stability analysis. The limit equilibrium method evaluates the overall stability of the sliding mass just on the verge of slip, using some or all of the three equations of static equilibrium of a plane problem. The stress-strain relationships of the rock mass are not considered. Method of analysis include the assumption of the shape of the slip surface. Peterson (10) introduced the Swedish method of analysis in 1916, which is based on cylindrical sliding surfaces. Fellenius (4) in 1926 extended this method and introduced the method of slices. This method was refined by Bishop (I) in 1955 and later used by Morgenstern and Price (8) in 1965. In many cases layers of extremely soft strata or strata weakened by neutral stress cause failure to take place by translation along plane of weakness instead of by rotation on a circular surface. In this paper, a slope with a horizontal layer of weak meterial is selected for analysis. This is a usual case for open pit lignite mines where lignite seam may be non-cohesive and 'weaker than the overburden rock or a soft clay layer underlies the seam. It is also a common case of rock fill dams supported on a foundation stratum of clay where the strength of the clay layer is less than that of the rock fill. It is shown that utilizing this method, the location of potential failure surface and the value of the minimum factor of safety can be calculated directly and the trial computations of factors of safety for a number of assumed failure surfaces are not necessary.

Jan 1, 1982

The US Constitution provides for regulation by the states for protecting the public's safety, health, and welfare. Hence, in the eyes of the law of all states today, this is the sole justification for registration of professional engineers. Wyoming was the first state to register professional engineers in 1907, to correct abuses of incompetent or fraudulent practices in surveying and real estate. Public safety and health are most directly affected by civil, electrical, and mechanical engineering. Other branches of engineering have a profound effect on the public welfare, including investors, and safety and health of employees. No arguments, pro or con, are valid except in relation to the registration laws of various states. Code of Ethics Few would argue the desirability of requiring conformance with a code of ethics. A major problem lies in enforcing compliance, since protecting the public demands a high standard of competence, yet assessing competence gets confused with restraint of trade. Bidding engineering work on price competition can lead to pressure to cut corners on engineering quality, and was therefore discouraged by codes of ethics. The Supreme Court, in a suit against the National Society of Professional Engineers (NSPE), barred any engineering society from such bidding restriction. It has, however, upheld the right of states to impose codes of acceptable practice as part of registration laws. For example, Texas Canon I reads, "The engineer's paramount professional responsibility should be the safety, health, and welfare of the general public." Anything less makes the code practically meaningless, but there are potential conflicts of interest in many engineering organizations. How can conflicts be handled? Any corporation could improve its public image by adopting a policy that each employed PE should, without fear of recrimination, record in writing over his seal any problem or flaw in any design that comes to his attention. The policy should further require that his superior provide him a written reply pointing out that the "flaw" is accepted as requiring correction or as a calculated risk, or overruled as erroneous or as a difference of opinion. Errors in calculation of judgment are inevitable. Despite this, there are limits to how much time and money should be spent to eliminate them. It is difficult, however, to see any excuse for failure to conscientiously evaluate the opinion of a PE. This may be an impossible ideal, but how else can the profession or the industry have credibility? The National Council of Engineering Examiners (NCEE) has a code of ethics one presumably subscribes to by signing an application to write a Principles and Practices examination. However, NCEE has none of the power of enforcement that is available through state boards of registration. Registration Qualifications Qualifications are set by the laws of the states. In general, they require passage of an eight-hour examination in fundamentals, preferably at graduation, and, later, one in principles and practices. The examinations are compiled and distributed by NCEE. This system provides for a high degree of uniformity and reciprocity. States set the education and experience levels (typically four years after graduation) required by those desiring to write the principles and practices examination. Examinations The principles and practices examination calls for answering eight of 20 equal weight questions; one on engineering economics, 19 on engineering. Economics may enter into engineering questions, but only provided the question is not answerable by an economist without engineering training. In preparing examinations, NCEE strives to use questions that require some judgment and can be more effectively answered by someone with four years experience beyond college. The aim is to assess entry-level professional

Jan 2, 1984

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By B. P. Bellport

This paper summarizes the Bureau of Reclamation's experience in the use of boring machines to excavate six major tunnels on the Bureau's water resources development projects in the western United States. The summary of experience is presented as a compilation of brief case studies for each of the six tunnels. Each compilation presents data on the tunnel dimensions, geological characteristics of the excavated rock, the tunneling machine used, machine operation, muck handling, method of tunnel support, ventilation system, and related information. The listing of the six tunnels in Table 1 reflects a diversity of tunnel lengths and diameters. However, despite this diversity of dimensions as well as the variety of rock encountered during excavation, the six tunnels have one major characteristic in common: their excavation was significantly expedited by the use of boring machines. Beginning with the 10,079-foot-long Tunnel No. 1 on the Navajo Indian Irrigation Project in New Mexico - the Bureau's first tunnel to be excavated by a boring machine - the boring machines, or "moles," have demonstrated their effectiveness in rapid and economical tunnel excavation. Tunnel No. 1, virtually 2 miles long, was bored through in 9 months, an unprecedented achievement in Bureau engineering experience, as compared with tunnels previously excavated by conventional means. Boring of the 45,630-foot-long Blanco Tunnel and the 26,610-foot-long Oso Tunnel, both on the San Juan-Chama Project in Colorado, set world records in rates of excavation,l/* Two days of exceptional progress highlighted the

Jan 1, 1970

By Ronald L. Gibbs

IN THE BEGINNING Contrary to popular myth, the personal computer can trace its roots back to a time before 1981 and the IBM PC. The seeds of the personal computer revolution were probably founded in 1975 with the release of the Altair (kit) personal computer, first advertised in Popular Electronics. June of 1975 marked the beginning of the Homebrew Computer Club in San Francisco. The founding membership list of the Homebrew Club now reads like a "Who's Who" of those involved in the early development of the personal computer industry. The Apple I computer was created by Steve Wozniak in early 1976 from the newly manufactured MOS Technology 6502 chip. It had 4,000 bytes (4K) of Random Access Memory (RAM] memory, a revolutionary amount of memory in 1976. Another early pioneer, the Commodore Pet computer, was another 6502 machine, but with 8K of memory. Tandy Corporation made its name in the hobby industry with leather kits. They embarked on a new path with the production of the TRS-80 line of personal computers. Most were based on the Z-80 chip, but again, were memory limited. A number of other Z-80 based systems followed later, including the Osbourne and the KayPro Computers. These systems were based on the Digital Research CP/M operating system and had a maximum of 64,000 bytes of memory (64K). The Apple I1 Computer appeared in 1977. Newer models of the original Commodore Pet and an Atari computer followed. These machines were also limited to 64K of memory addressing, and the early models typically shipped with only 16K, 32K, or 48K of memory. The Z-80 and the 6502 were the first truly commercialized CPU chips touting boxes with key- boards, monitors (sometimes a TV), and the ability to expand (peripheral slots for serial communications, centronics parallel communications, etc.1. They all shared one technology, audio tape as a storage media. The use of a portable tape recorder provided inexpensive, if not always reliable, magnetic storage. The tape recorders were typically finicky and required patience to use. Adjustments to the volume control were often needed to find "just-the-right" setting for loading or saving information. This kept the personal computer from being accepted in many markets, and gave it a reputation as a hobbyist or experimenters' toy. In early 1979, Steve Wozniak finished the design of a floppy disk drive and controller. This was a revolutionary design which reduced the "then" standard number of controller chips from fifty-plus, to just eight. With the advent of an affordable floppy disk drive mechanism, the personal computer was about to gain respectability. From a business standpoint, it was now possible to save and reliably retrieve business information. It also provided a superior means of distribution for commercially created software. Commercial software became a commodity rather than an oddity.

Jan 1, 1993

By Yosry A. Attia

One of the most significant advances in Mineral Processing in recent years, is the development of the selective flocculation technology. The technology is primarily aimed at recovering the mineral values from ultrafine ore suspensions. This is achieved by selectively aggregating the mineral particles in question to such size as to enable their effective separation from the suspension. Selective flocculation utilizes the differences in the physical-chemical properties of the various mineral components in the mixed suspension. It is based on the preferential ad- sorption of an organic flocculant on the particular solids to be flocculated, leaving the remainder of the particles in suspension. In order to understand the mechanics of this process, selective flocculation may be divided into four major sub processes; these being: ore slurry dispersion, in which all the particles are stably and uniformly distributed in the suspension with the individual particles being essentially separate; flocculant selective adsorption and floc formation; floc conditioning, which aims at obtaining flocs with desire properties for their subsequent separation and with minimum entrapment of dispersed particles; and floc separation from the suspension. These sub processes will be reviewed later in this article.

Jan 1, 1982

By Phillip Crowson

The annual surveys of corporate exploration expenditures carried out by Metals Economics Group (MEG) show that estimated total spending rose to a record $13.2 billion in 2008 ($14.4 billion including expenditure on uranium exploration). This compares with the previous peak of $5.2 billion in 1997. MEG does not adjust its figures for the effects of inflation but recognizes that the substantial increase in budgets of recent years has not been reflected in a proportionate rise in actual activity on the ground (MEG, 2009). In recent years, costs were boosted by rising prices of fuel and other inputs, and acute shortages of qualified staff and drilling rigs. The inflation rate for exploration substantially exceeded increases in general price levels as measured by national indices. Just how much exploration costs in-creased, however, is probably not widely appreciated. Figure 1 compares the MEG estimates of total annual dollar spending in Australia, Canada and the United States combined with their drilling activity, measured in meters drilled, as reported by national agencies. These three countries accounted for 39 percent of MEG?s estimate of total spending on minerals exploration in 2007 and 40 percent in 2008. Expenditure is shown both in money terms, as reported by MEG, and adjusted to real terms, with the U.S. implicit gross domestic product (GDP) price deflator. The comparison is of index numbers based on 2000 as 100. Comparisons for the individual countries are shown in Fig. 2 to 4. National figures for drilling activity and expenditures cover some minerals like iron ore, coal and industrial minerals (29 percent of Australian spending in 2007 to 2008 and 10 percent of Canadian in 2008) that are not included in the MEG estimates of spending. Such exploration has risen more than the total since 1997 so that the index of drilling activity in the figure may be overstated for recent years on a like for like basis with the MEG data. MEG only includes spending on uranium exploration in recent years whereas the national agencies include it throughout. Figures 5 and 6 com-pare national and MEG estimates for Australia and Canada. No comparable figures are available for the United States. The national estimates have been converted to U.S. dollars at the appropriate annual average exchange rates, and the Australian annual totals have been summed from the published quarterly data. Not only is spending cyclical, but so are unit costs. Australian and Canadian data show that total exploration spending per meter drilled rose by 2.5 to 3 times between 2001 and 2008. These rises may partly reflect increasingly complex drilling methods, and an increased share of assaying and testing in total exploration costs. In Canada, however, diamond drilling accounted for a lower footage of the total in 2005-2007 than in the preceding few years, and spending on exploration, as opposed to deposit appraisal, made up a higher proportion of the total. Figure 7 compares index numbers of exploration spending per meter drilled in U.S. dollars for Australia and Canada. These figures raise a number of questions. First, is the relationship between total expenditure and meters drilled in the three countries for which data are available typical of the global experience? Secondly, has there been a significant change in the make-up of exploration spending in recent years? The Canadian data do not suggest that there has been, but is Canada typical? Has drilling become less important relative to other exploration techniques, or is it just as important as ever in confirming the existence of viable ore deposits?

Jan 1, 2009

By Adriaan de Villiers

Many conventional structural analysis and design methods in current use are not appropriate for the mining industry. Two major reasons for this are that: • The economic life of a particular mine is limited, and • Much of the equipment and machinery used by the mining industry operates at relatively low speeds. Both of these factors can have significant cost implications if they are not properly accounted for during plant design. In particular, the often used practice of mitigating excessive vibration by adding mass to machinery supports is not only expensive but may worsen the vibration effects. Some of these problems, such as increased wear and tear, are not always easy to trace back to inappropriate design. This article focuses on vibration related issues and demonstrates that the mining sector has unique problems requiring unique solutions. Vibration: the basics Historic developments leading to current vibration design practices provide the key to why such practices are often inappropriate for the mining industry. To understand this, it is necessary to introduce some basic vibration theory. Consider a simply supported beam or foundation on which a vibrating machine is mounted. For analysis of the system's dynamic response, it may be viewed as a mass attached to a spring and a damper, such as the shock absorber of a car.

Jan 1, 1992

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By Dan Witkowsky

For the 36th consecutive summer, the Colorado Mining Association Education Foundation and the Colorado School of Mines have sponsored “A Total Concept of the Mining Industry” for kindergarten through grade 12 teachers. Teachers from 34 states, plus the District of Columbia and two foreign countries, have graduated from the four-week course. They received six hours of recertification credit. This summer 31 teachers from Colorado, Kentucky, Virginia and Alaska completed the program. The course is unique from other shorter courses in that it solicits teachers of all disciplines from all K-12classes. In addition to the expected earth science and mathematics teachers, the Class of 2004 consisted of educators who teach music, chemistry, biology, social studies, history, basic English and world history. Others in the program included those who teach American history, physical and life science, remedial reading, consumer/family studies, “world of work,” language arts, engineering technology, environmental science, world geography, human anatomy and physiology, and business.

Jan 1, 2004

By Terry I. Mudder

Metal complexed cyanides in wastewaters form as a result of interactions of free cyanide with metals present in the wastewater and exhibit varying degrees of stability, toxicity, and treatability. Thiocyanate, a pollutant commonly found in cyanide bearing wastewaters, is formed through the interaction of free cyanide with sulfur containing species (i. e. pyrrhotite) both present in the wastewater. In certain industrial processes, such as the beneficiation of gold and silver, cyanide is an essential reagent. Since free cyanide, complexed cyanides, and thiocyanate are potentially toxic to humans and aquatic organisms, these compounds must be removed from wastewaters prior to their discharge into surface or ground waters serving as potential potable water sources, marine or fresh water habitats

Jan 1, 1984