Search Documents

By E. Hakami

The objective of the study was to estimate the largest shear displacement that could be expected on a pre-existing fracture located in the repository area, due to the heat release from deposited waste. Two-dimensional numerical analyses using UDEC have been performed. The maximum shear displacement, at the fracture centre, amounts to 0.2 – 13.8 cm depending on fracture parameters. The fracture extension, friction angle and shear stiffness are found to be the most important. Le but de cette étude est de déterminer le déplacement maximal en cisaillement qui puisse se développer le long d'une fracture préexistante en réaction à la chaleur dégagée par les déchets radioactifs enfouis dans la roche. Les analyses numériques ont été réalisées à l'aide du code 2D UDEC. Le déplacement maximal en cisaillement enregistré au centre de la fracture varie entre 0.2 et 13.8 cm en fonction des propriétés de la fracture. L'ouverture, l'angle de friction et la rigidité au cisaillement semblent avoir une influence dominante sur les résultats. Zielsetzung der Studie war die Abschätzung der maximalen Scherverschiebung, die auf einer innerhalb des Endlagergebietes existierenden Rissfläche infolge der Wärmeabstrahlung des eingelagerten Materials zu erwarten war. Es wurden zwei-dimensionale numerische Berechnungen mit UDEC durchgeführt. Die maximale Scherverschiebung im Zentrum der Rissfläche beträgt 0.2-13.8 cm, abhängig von den Risseigenschaften. Dabei hat sich herausgestellt, dass Rissgrösse,Reibungswinkel und Schersteifigkeit den grössten Einfluss haben.

Jan 1, 2003

By B. Yu, M-H. Cao, C. Zhou, X-Z. Zhang

The transient infiltration and lubrication behaviour of slag during continuous casting of steel is important for billet quality. A two-dimensional coupled mathematical mould model was developed to investigate these phenomena. The accuracy of the model was verified by comparing the calculated slag consumption with measurements by the plant. The results show that the liquid slag is consumed from the middle and late period of positive strip time to the next early period of positive strip time, including the entire negative strip time. The maximum downward infiltration velocity and positive pressure in the slag channel is at the middle of the negative strip time. Increasing the positive pressure of the slag channel is conducive to lubrication. The shear stresses acting on the shell surface and at the mould side were determined by the lubrication slag consumption and total slag consumption, respectively, and gradually decreased with increasing slag consumption. The negative strip time was lengthened to increase the slag consumption and prolong the time near the maximum downward shear stress, so as to be conducive to the demould.

Apr 16, 2024

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMC's (now BHP Billiton's) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007

A knowledge of the steady-state mass and energy requirements of a particular process is essential to a determination of the economic feasibility of that process. A predictive simulation technique can be of great value in this respect. A versatile computer program based on a fundamental thermodynamic approach has been developed for the prediction of process requirements. The equilibrium composition of a multiphase system is determined by the technique of free energy minimization. Energy-balance calculations are performed using the appropriate thermodynamic data for the chemical species present in the composite materials used. All models for the process units under consideration are written in modular form, the output being calculated from the input and the specified operating conditions. The computer program is written in such a way that it can be used easily by anyone familiar with the processes involved, even though he may have no previous experience with a program of this type. The program is structured so as to facilitate the varying of one parameter without any alteration to the others, thus simplifying the investigation of the effects of any parameters considered to be important. The program has the advantage of being able to compare existing and new processes on the same basis, namely from the ores to the molten metal.

Jan 1, 1987

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper-gold mine has continued to process significant quantities of complex transitional mixed ores. Initially, the ore treated came predominantly from accumulated stockpiles. Subsequently, the feed source shifted primarily to freshly mined ore that generally showed less tarnish with better flotation kinetics, but with the downside of lower concentrate grades. A number of changes were made to improve the efficiency of the rougher circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory flotation test work that were discussed at length in a previous paper1. Salient among the recommendations adopted as a result of previous work were increased circuit capacity and a modified configuration to increase the residence time and the number of sulphidization stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and a below-specification final concentrate product. This was due primarily to higher mass pulls from the extended rougher bank with multiple concentrate discharge streams, and which necessitated an enlarged cleaning capability. The extra cleaning capacity came on stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. IntroductionThe Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining plc, a subsidiary of First Quantum Minerals. The remaining 20% is owned by the state through the parastatal Zambia Consolidated Copper Mines Ltd (ZCCM). The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005."

Jan 1, 2016

By A. Navarra, A. Quelopana

The mine production scheduling problem (MPSP) has been studied since the 1960s, and remains an active area of computational research. In extending the concepts of the MPSP, the automated mine may now be regarded as a hierarchical intelligent agent in which the bottom layer consists of distributed robotic equipment, while strategic functionality occupies the higher layers. Here we present a disambiguation of artificial intelligence, machine learning, computational optimization, and automation within the mining context. Specifically, the Q-learning algorithm has been adapted to generate the initial solutions for a high-performing strategic mine planning algorithm, originally developed by Lamghari, Dimitrakopoulos and Ferland, based on the variable neighbourhood descent (VND) metaheuristic. The hierarchical intelligent agent is presented as an integrative conceptual platform, defining the interaction between our new Q-learning adaptation and Lamghari’s VND, and potentially other hierarchically controlled components of an artificially intelligent mine, having various degrees of automation. Sample computations involving Q-learning and VND are presented.

Dec 1, 2021

By S. L. Miller

The development of a pilot gold geostatistical ore reserve system proved that geostatistical methods worked well for the routine production of annual ore reserves on gold mines of the Gold Fields of South Africa (GFSA) group, and that the techniques could also be practically implemented, understood and accepted by Survey Department personnel. Many side benefits of the pilot system became apparent, and a variety of useful management information was provided by manipulating the data values that were already captured. It was decided that it was a priority computing project to develop a standard production system (GORS) for routine use by all the GFSA gold mines. Experience with the pilot system enabled detailed functional specifications for GORS to be laid down. These, together with group computing policy determined the terms of reference and constraints for the GORS development. System design could not be finalized until new and appropriate mainframe database software and graphics workstation equipment and software had been found. With these in place the basic system was structured to take best ad- vantage of the interactive features of the workstation, the number-crunching power of the mainframe and the flexibility offered by a relational database and associated 4GL tools. Application sub-systems were developed for data capture, statistical applications, geostatistical calculations, contour plotting and graphical queries. GORS is being introduced to the mines in a phased manner with suitable documentation, training and support structures to enable it to be routinely and effectively used on a day-to-day basis by all group gold mines.

Jan 1, 1987

By C. Holck, J. Yarmuch, J. Read

"Steepening of slopes provides the means to reduce waste extraction and increase ore recovery in open pit mines; however, it may also adversely affect safety by posing a higher risk of slope failure. The implementation of slope monitoring programmes is recommended to manage this risk inherent in steeper slopes. In this paper, the design and evaluation of monitoring campaigns to measure subsurface deformation and groundwater pore pressure in open pit mines is presented. The monitoring programmes were applied to a theoretical case of an open pit mine designed using DeepMine software (BOAMine SpA, 2015). Mine plans were developed based on the initial base case scenario with monitoring programmes considered for four types of monitoring instrumentation: two established technologies, in-place inclinometers (IPIs) and vibrating wire piezometers (VWPs); one emerging technology, the ShapeAccelArray (SAA); and a novel technology under development, the Enhanced Networked Smart Markers (ENSMs). Technical and economic appraisals of the monitoring programmes and sensitivity analysis of the developed mine plans showed that using ENSMs spaced every 4 m had the lowest cost per unit of data gathered. IntroductionSeveral open pit mines have already exceeded their design life and, as they become deeper and reach depths over 1000 m, they face higher rock stress levels and tensile deformations (Stacey and Xianbin, 2004; Stacey et al., 2003). The more complex the conditions in modern open pit mines, the more difficult it is to achieve long-lasting, stable pit slopes and to meet the mine’s economic needs: maximize financial returns, minimize risks to operational safety, achieve optimal ore recovery, and minimize waste extraction (Stacey, 2009). Steepening of slopes provides the means to reduce waste extraction and increase ore recovery (Stacey, 2009; Calderon and Tapia, 2006; Bye and Bell, 2001; Jefferies, Lorig, and Alvarez, 2008); however, it may adversely affect operational safety, as steeper slopes are less stable than shallow slopes (Steffen et al., 2008; Mphathiwa and Cawood, 2014)."

Nov 1, 2018

By Y. R. Murthy, P. K. Satija, A. Srinivasulu, S. K. Tripathy, A. Ranjan

"In this investigation, we optimize the grinding circuit of a typical chromite beneficiation plant in India. The run-of-mine ore is reduced to a particle size of less than 1 mm in the comminution circuit and concentrated using gravity separation. The comminution circuit comprises two-stage crushing and single-stage grinding in a ball mill in closed-circuit with a highfrequency screen. A detailed circuit audit was undertaken at the plant to understand and evaluate the performance of the grinding circuit. The audit revealed abnormalities in the process and design parameters which caused high energy consumption, lower throughput, and loss of ultrafine chromite. Laboratory studies indicated the differences in the grinding properties (work index, breakage rate, etc.) and liberation sizes of these ores. Studies also revealed that grinding media size, particle retention time, and pulp density are crucial in coarse grinding. Based on the laboratory grinding and characterization studies; simulation studies were performed to optimize the operating parameters of the grinding circuit.IntroductionComminution is a critical process in mineral processing which strongly influences the economics of production. In mineral processing, particles containing valuable minerals must be disintegrated at a sufficiently fine size to liberate valuable minerals from waste constituents, so that they can be easily separated by an appropriate beneficiation method. The Sukinda chrome ore beneficiation plant utilizes different types of run-of-mine (ROM) ore with different physical properties (viz. grindability characteristics, work index, mineral composition, liberation, chemical composition, etc. for the production of chrome concentrate. In the feed preparation circuit, the ROM ore is crushed and ground to below 1 mm. Grinding in the chromite beneficiation plant is a critical unit operation to achieve the desired product size of below 1 mm and to control the generation of the ultrafine particles. Furthermore, about 40% of total power consumption in the beneficiation plant is accounted for by the grinding of the ore. This implies that any improvement of the circuit performance will lead to an overall increase in productivity."

Jan 1, 2017

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By Luis Rudolphy, Pekka Tähkiö

"Flotation plant design, construction and start-up can be challenging tasks, because multiple factors and disciplines have to be combined in an efficient manner, in order to execute a project that meets the technical, financial and timeframe expectations. Key considerations that need to be addressed when designing a flotation plant are process requirements, equipment integrability, automation, and up- and downstream processes/designs. Furthermore, several other lifecycle factors need to be considered, such as servicing and maintainability, operational costs, future expansions and decommissioning, among others. To address these challenges, Outotec has developed a new approach to designing flotation plants that targets eliminating most of the inherent risks that can be found in these types of projects. The new Outotec® plant is a fully modular approach in which the above-mentioned challenges have been taken into consideration in the design phase. As a result, the cPlant concept can give several benefits for new and experienced companies involved in the minerals processing business, such as lower risk investments, fast and cost-efficient flotation plant delivery, faster ramp-up period, easy plant expansions, fully automated processes and operation and maintenance ease. As well, dismantling and transportation of the cPlant to a new location is easy and fast, hence the new cPlant concept makes possible to exploit small, short-lifespan ore deposits and also retreat old tailings ponds that might contain valuable minerals and where the ore quantities are limited. Furthermore, cPlant is easily implemented for brownfields and temporary expansions during bigger expansions."

Jan 1, 2015

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 25th August, 1971, at 4.15 p.m. Mr V. C. Robinson (President) was in the Chair. There were also present fifty one Fellows, twenty one Members, two Associates, two Students and fourteen Visitors, making a total of ninety one. The President declared the meeting open at 4.15 p.m. OBITUARIES The President: 'It is my sad duty to announce the death of the following members of the institute: H. J. G. C. Arndt, Life Member, joined 1933, passed away 11th May, 1971. J. H. A. Diering, Fellow, joined 1921, passed away 24th June, 1971. L. O. W. Leimer, Fellow, joined 1960, passed away 25th June, 1971. E. A. Meltzer, Fellow, joined 1941, passed away April, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 17th March, 1971, as published in the July, 1971 issue of the Journal?' Agreed. WELCOME TO VISITORS The President: In welcoming you here, ladies and gentlemen, it gives me great pleasure to see so many of our office bearers-our important honorary office bearers-and particularly I would like to welcome our Honorary President, who is, as you know, the President of the Chamber of Mines, Mr John Shilling, and we are 'privileged also to have with us two of our Honorary Vice-Presidents. One in particular I am very pleased to welcome here, and that is Mr G. F. van L. Froneman, who is the Administrator of the Orange Free State, and we extend a very hearty welcome to him, because he is a long way from home. Then we have another Honorary Vice-President, Mr Tommy Gibbs, the Government Mining Engineer, and there are many distinguished guests, whose names I want to give you, so that you will know who they are. We are happy to have present: Mr R. C. J. Goode, Member of Council, I.M.M. London; Mr E. Boden, Manager, A.S. & T.S. of S.A.; Mr G. A. P. Louw, The President, The Associated Scientific and Technical Societies of S.A.; Mr I. R. G. Stephen, The President, The South African Institution of Electrical Engineers; Mr A. S. Robinson, The President, The South African Institution of Civil Engineers; Mr C. F. J. Schneider, The President, The Institute of Land Surveyors of the Transvaal; Mr R. J. Vermaak, The President, The South African Institute of Assayers & Analysts; Prof J. P. F. Sellschop, The President, Joint Council of S.A. Scientific Societies; Mr T. C. Watermeyer, The President, The Federation of Societies of Professional Engineers; Mr G. A. MacWhirther, The President, S.E.I.F.S.A.; Mr C. G. Hinds, The President, The Mine Managers Association; Mr J. F. Aldersley, The President, The South African Institute of Foundrymen; Dr H. O. Reisener, The President, The Institute of Welding; Dr F. P. A. Robinson, The President, S.A. Corrosion Council; Mr A. Bain, The Chairman, Witbank-Middelburg Branch; Prof D. J. Schoeman, The Chairman, The S.A. Institution of Chemical Engineers; Dr N. P. Finkelstein, The Chairman, The South African Chemical Institute (S.Tvl Section); Mr J. M. Meyer, Chairman, O.F.S. Branch. To all these guests and their ladies, I extend a most cordial welcome, and hope that you are going to enjoy the afternoon. MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates having been published in accordance with By-Law 5.2.2., Council has elected them to membership in the following grades: Fellows: Richard Lloyd Blandy, Byron J. Haley. Members: Brian Roger Borton, Frederick Brian Peacock, Peter John Stacey, Kenneth Niles Thanstrom. Students: Peter Boesley James, Kenneth Brian Perel. TRANSFERS From Member to Fellow: Cecil Eugene Fivaz, Peter Edwards. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade. ANNUAL REPORT OF THE COUNCIL AND ACCOUNTS FOR THE YEAR ENDED 30TH JUNE 1971 THE PRESIDENT: We now come, ladies and gentlemen, to the annual report of the Council of the Institute-and our accounts for the year ended 30th June, 1971, and these documents are on your chairs; I know you probably haven't had time to study them yet, but I would like to highlight some of the things which I think are worth mentioning. I would ask you to take, first of all, ladies and gentlemen, the report of the Council as being read, and before moving adoption, however, there are certain salient points I wish to touch on, and I will leave the financial side of this entirely to our very competent and worthy, Honorary Treasurer, Mr Denis Maxwell.

By S. Mohanty, K. Sarangi, S. Dash, P. P. Patra

Industrial effluent from various industries contains heavy metals that are a serious threat to humans, flora and fauna in water bodies, and the environment. The heavy metals are dumped after precipitation, which has serious environmental consequences. In this paper, a 2D axi-symmetry CFD model has been developed to study the extraction of chromium ion from industrial effluent, in a hollow fibre membrane, using Alamine 336 as the carrier and kerosene as the diluent. The Navier Stokes equation was used to predict the velocity profile of the aqueous and organic phases, and species transport equation, which considers both convective and diffusive mass transfer, was used to predict the concentration profile of the chromium ion in the computational domain. The distribution coefficient was experimentally determined at a pH 4, which was found to be the optimum pH. Numerical simulations were performed considering 11.11 mol/m3 of initial feed concentration for chromium ions and extractant concentration of 0.2 M. Simulations were carried out with various aqueous and organic flow rates, and validated with experimental data. Keywords: CFD, metal extraction, hollow fibre membrane, heavy metals

Jan 1, 2020

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries to remove iron and sulphur from the molten matte phase. This technology has not changed significantly since its inception in the early 20th century. The typical converting operation involves lateral purging of air/oxygen-enriched air into molten matte through a bank of tuyeres. This blowing operation occurs at low air pressure from the blowers, and the induced bubbling regime is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks include recurrent tuyere blockage, inevitable tuyere punching operation to clear airways, and low oxygen efficiency as a result of substantial air losses due to leakages.Investigations in the 1980s demonstrated1 that jetting into Cu and Ni converters could reduce or eliminate some of the process difficulties. In spite of these findings, very little progress has been made in the application of these concepts for converting of non-ferrous melts on a commercial scale.As part of its operational improvement and energy reduction initiative, Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to full-scale industrial evaluation, a numerical assessment was conducted to ascertain the feasibility of implementing sonic injection on Lonmin converters. The work included flow characterization at high injection pressures achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid (VOF) and realizable k- e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were applied using the commercial CFD numerical code FLUENT.This paper discusses the key findings regard ing understanding of gas plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a fullscale implementation of sonic injection in the smelter."

Jan 1, 2014

By E. Kumar, L. A. Kumar

"A methodology is proposed to develop an optimization model to understand the impact of transporting minerals, from mines to the final destination, on air quality. Recently, there has been increasing concern about the combined effects of multiple activities over many years, and the regional environmental changes brought about by a single project. Environmental issues in the iron ore industry have highlighted the need to broaden the cumulative impact assessment. In this study, we simulated the optimal routes and quantity of materials needed to meet the destination plant demand based upon environment constraints (level of air pollution), as well as the cost of transportation and availability of materials. Multiple scenarios were developed to analyse the effects of changes in routes, alternative transport system (or multi-modal split), traffic congestion, and the cumulative impacts on air quality. The air quality impact zones of the study area were demarcated using a GIS technique. The expected outcome of the study is the selection of a suitable transport system for a particular site with the least impact on air quality, including the transportation route, relative to the minimum cost of transportation of the minerals from the mines to their final destination. The proposed methodology is evaluated with a case study. IntroductionIn India, the process of environmental impact assessment (EIA) has been focused primarily on the local impacts of projects, without considering regional environmental effects. Environmental clearances for proposed projects are based on reports of local impacts. However, any developmental project poses a potential risk to the environment as a whole, and not just in the immediate vicinity of the project. Recently, there has been increased concern about the combined effects of multiple activities over many years—the regional environmental changes due to development of a single project (Dutta, Mahatha, and De, 2004). Environmental issues throughout the country, particularly in the iron ore industry, have emphasized the need to broaden the analysis to include the combined impacts, or those forecast for a proposed region, on an existing environment. The most significant adverse environmental consequences of iron ore transportation are the deterioration of biodiversity and air quality (Kumar and Ajay, 2015)."

Jan 1, 2017

By C. Bergmann, V. Ross

The concept of underground ore processing, in which valuable ore and waste are separated at a coarse particle size to improve the economics of operations and minimise the environmental impact, seems attractive from a sustainability perspective. Perceived benefits of such an operation include energy and cost savings due to a reduced hoisting load, a reduced footprint of surface operations, and using material for backfill that has not been contaminated by process chemicals. Progress in the South African mining industry in this area has however been below expectation, and opportunities for underground processing in deep, narrow reef operations were therefore explored by an Excel-based simulation with sensor-based sorting (SBS) as concentration technology. Various PGM mining scenarios incorporating factors such as the mining rate, depth of operation, and effects of dilution and particle size on the metallurgical efficiency, were compared. Whilst these initial results can be regarded as indicative only, they have shown that the economics of such an operation are driven by selective mining at significantly higher rates than achievable with conventional methods. Also, the cost of preparing, conveying and placing rock backfill will need to be lower than that of hoisting waste and depositing it on a surface dump. Another aspect to be addressed is whether ore sorting machines would be able to operate under harsh conditions underground and what provision would need to be made to ensure their efficient operation. Further investigations should focus on refining costs, incorporating environmental considerations in the modelling of economics and sustainability, and compare greenfields with brownfield scenarios. Keywords: Ore sorting, hoisting, backfill, mining rate, economics simulation

Jan 1, 2020

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020

By M. Mpofu, M. van Schoor, T. Kgarume, H. Grobler

The South African mining industry has committed to achieving a state of zero harm for its workforce, with a strong emphasis on worker health and safety. Among the major safety concerns are falls of ground, a leading cause of injuries and fatalities. Ground-penetrating radar, a non-destructive geophysical method, is recognised for its ability to image structures, fractures, and geological features within the rock mass. However, ground penetrating radar data is often acquired in local coordinates, posing challenges for visualisation in mine computer-aided design or three-dimensional visualisation software. This study explores the pivotal role of light detection and ranging data in transforming ground penetrating radar data from local survey coordinates to absolute mine coordinates. A comprehensive georeferencing methodology is presented, providing the stepwise progression from the initial georeferencing of ground penetrating radar data to the ultimate integration of ground penetrating radar and light detection and ranging datasets, resulting in the creation of a ground penetrating radar-light detection and ranging three-dimensional model. The proposed approach not only facilitates the integration of but also offers a practical means of visualising the integrated datasets within commonly used computer-aided design or three-dimensional visualisation software. An essential aspect of this integration is the adoption of non-proprietary data formats, specifically American Standard Code for Information Interchange text files, ensuring broader accessibility and compatibility. The potential for integrating diverse datasets to construct insightful models of the underground mining environment is illustrated. Integration of different datasets has the potential to offer a holistic understanding of the mining environment, providing essential information to decision-makers.

Jul 23, 2025

By S. A. Lorentz, Y. Xu, C. Theron

The failure of tailings storage facilities (TSFs) results in the discharge of significant quantities of hazardous waste material into the natural environment. Research studies relating to slope instability have identified physical mechanisms such as rainfall-induced erosion, liquefaction, and shear failure as the main triggers. The generation of transient pressure waves and the mobilization of pre-event water in the unsaturated zone have been found to trigger shallow landslides in natural hillslopes. In this paper we review these physical mechanisms, known as groundwater ridging (GWR) and the Lisse effect (LE), from other studies. Previous researchers have explained both these phenomena through field and laboratory observations, numerical modelling, as well as conceptual discussions. These case studies demonstrate the impact of rainfall characteristics on the generation of transient pressure waves that rapidly increase the phreatic surface and change pore water suction. Reference is also made to the influence and behaviour of physical porous medium characteristics on the establishment of a continuous water phase that facilitates the transmission of an induced pressure head. However, previous studies fail to recognize the possibility that the pressure increase in pre-event water through pore air propagation could cause slope instability in tailings dams. The authors suggest that the physical properties and hydraulic behaviour of unsaturated porous tailings media make it susceptible to GWR and the LE, resulting in the creation of a potential failure plane.

Feb 2, 2022