Search Documents

By Z. Nzimande

The Constitution of the Republic of South Africa advocates the importance of sustainable economic development and justifiable environmental consciousness by business. The government needs to ensure that every citizen of the Republic has access to an environment that is protected, pollution free, and sustainable by enacting certain regulations. However, there are more than 5 700 derelict and unrehabilitated mines of all types in South Africa. Former asbestos operations were among the first to be targeted for clean-up under the programme instituted by the Department of Mineral Resources (DMR), owing to the proven direct impact of asbestos pollution on health. This paper seeks to investigate the challenges faced by the coal sector as far as mine rehabilitation and closure is concerned. For the purpose of this paper rehabilitation is defined as per the Chamber of Mines Rehabilitation Guidelines publication, which defines rehabilitation as putting the land impacted by mining activities back to a sustainable and usable condition. Some of the current rehabilitation challenges are technical skills (know-how), leadership focus, poor planning, cost saving initiatives, and the government's lack of capacity to enforcement rehabilitation requirements. It is imperative that mining companies identify rehabilitation as a critical strategic pillar that directly influences license to operate. The case study evidence indicates that relevant policies, appointment of accountable people, sufficient leadership support, and the correct choice of rehabilitation equipment can assist to improve the rehabilitation and land management challenge.

Jan 1, 2012

By J. Grobler, J. Zietsman

"Understanding the influence of feed material mineral assemblage on spiral separation is paramount for the successful and consistent operation of a spiral plant. Plant stability is required to maintain high recovery of valuable heavy minerals (VHM). Standard material analysis methods used in the heavy mineral industry to evaluate spiral separation behaviour are unable to quantify performance differences in the case of large variations in feed assemblage. This study illustrates a systematic approach to evaluate spiral separation performance. This technique was applied on a four-stage spiral plant. The performance information was used in a circuit simulation to clearly illustrate the importance of correct setting of the spiral splitter position and resulting spiral mass loading to ensure optimal circuit stability and maximum VHM recovery.IntroductionHeavy mineral sands deposits generally consist of naturally fine-grained, free-flowing sand due to the way in which the deposit was formed. The size of the heavy minerals market is roughly 8 Mt/a of zircon and titanium combined (Iluka, 2013). If an average combined feed grade of 5% zircon and titanium and an average combined overall product recovery of 80% are assumed, the resulting run-of-mine feed tons that would require primary spiral beneficiation is 200 Mt/a. The number of spirals required for the processing of this material, assuming 6500 operating hours per annum, an average of 2 t/h per start, and the same number of rougher spirals as other duty spirals, is over 30 000 spirals for the heavy mineral sands business alone. These numbers clearly illustrate the importance of the spiral in the heavy mineral industry.The aim of a spiral plant in the primary processing value chain of a heavy mineral process is to reject non-valuable quartz (a light mineral) from various valuable heavy minerals (VHM). The product from the spiral plant is a heavy mineral concentrate that has a reasonable grade (more than 90% heavy minerals) at a reasonable heavy mineral recovery (greater than 90%). This benchmark is fairly easy to achieve if all the mineral particles are well liberated (as in the case free-flowing sand), the feed is properly deslimed (-45 µm fraction removed to less than 5% of the solids mass), and the spirals are fed within design solids concentration (water to solids ratio) and design spiral load (dry tons per hour per start)."

Jan 1, 2017

By J. C. R. van Schoor

In this study the applicability of a batch press to predict the energy consumption and particle size distributions for medium-pressure roller presses was investigated. The relationships between energy consumption, feed size and product size are discussed with reference to Hukki?s interpretation of Bond?s and Rittinger?s laws, as well as the particle size parameter used. It was found that the comminution laws have limited utility for the characterization of the performance of the medium-pressure roller crushers or the batch press used, and also depend on the particle size distribution indicator used. It was also found that the batch press is not a suitable simulator for medium-pressure roller mills as it was notable to predict the energy requirements, or to predict the size distributions that would be obtained for the ores evaluated.

Jan 1, 2012

By F. A. G. M. Camisani-Calzolari

Approximately 850 groundwater samples were collected over a 29 300 km2 region of the semi-arid Northwestern Cape during the site selection phase of the South African radioactive waste disposal project. The purpose of the geostatistical investigation was primarily to delineate metallogenic occurrences and provinces which might exist below the thin veneer of surficial material and could thus interfere with the suitability of the site, and to quantify the distribution patterns of groundwater parameters in order to establish a relationship to local and regional geology. Up to 34 variables were analysed for each sample. Structural analysis revealed that the study area is statistically uniform. The variables have low correlation coefficients, with the exception of major ions, indicating a general poor degree of interrelationship between the spatial distribution patterns of the different variables. On the other hand, the long semivariogram range of the majority of variables, which reaches 70 km in cases, demonstrates their continuity on a regional scale. Kriging, which was repeated for each parameter, reveals that most variables, particularly trace metals, have distribution trends which are not influenced by local geomorphology or surface lithology. A 50 km wide, 220 km long metallogenic province, defined by kriging, could possibly reflect a broad metallogenic imprint on the basement and could represent a target area for prospecting. Kriging also reveals the possible existence of a wrench faulting system which may well have influenced the Namaqualand coastal graben and the western boundary of the Karoo.

Jan 1, 1987

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

By V. E. Cogho

Optimum Coal Mine comprises numerous defunct, active, and future mining sections. The mine is primarily a large opencast coal mine; however, underground mining activities will be increasing steadily over the next five years. Opencast and underground mining activities have a significant impact on surface and groundwater resources. To ensure that the mine will be able to continue with its mining operations in the catchment, the extent of this impact requires that substantial intervention and mitigation measures need to be implemented to ensure the environmental integrity and economic use of the catchment's water resources. In developing a sustainable long-term mine water management strategy, numerous scenarios had to be analysed. The various scenarios are a combination of water and land management activities. The main components of the mine's integrated water management strategy include: ? Management of water recharge by continual and appropriate rehabilitation of disturbed land ? Beneficial re-use of impacted mine water for coal plant process water and mining operations ? Reclamation and desalination of remaining excess impacted mine water to potable standard. From the mine's long-term water balance, it is evident that the continued implementation of numerous water management actions is required to mitigate the water resources impact in a sustainable manner. In addition, the installation of a water reclamation plant at Optimum Coal Mine (15Ml/day) is a key step for the mine to achieve a zero impact target.

Jan 1, 2012

By R. I. Klintworth

The multi-reef area of Cooke 3 Shaft provides a unique mining challenge on account of the very thin middlings between the pay bands and the marginal values of the reef. It is uneconomic or impractical, because of the excessive heights, to mine the middlings using conventional stoping methods. The development of suitable mining methods is discussed with particular emphasis on the control of water inflow and the policy of not jeopardizing or sterilizing other reef horizons by the mining method implemented. No definite solution is currently available, but with the aid of instrumentation, computer analyses and mechanized mining equipment, the mine continues to attempt to maximize extraction and profits.

Jan 1, 1988

By J. -M. Chautru

A geostatistical simulation of a typical mining site for polymetallic nodules in the North Pacific Ocean is presented. This is the first stage in the design of an industrial mining system. Two variables which have a major effect on the orebody's economic potential are considered, namely: the maximum slope of the ground inside a mining block of 50 x 100 m; and the average quantity of nodules on the same support. Two geostatistical problems have emerged in this study. The first is due to the lack of a change of support model for the maximum of a variable. A provisional solution, considering an experimentally accessible 'equivalent' support, is proposed. The second is due to a non-linear link between the two variables. To be able to take this into account in the simulation, we propose a new method based on the decomposition: X = E(X/Y) + Residue (X). Satisfactory results were obtained with this approach.

Jan 1, 1987

By R. M. G. Machunter

The use of testwork to establish an economically feasible separating plant has been a long established practice in the mineral processing industry. However, uncertainties in orebody characteristics and equipment/plant operation can have a significant impact on the separation performance of a given project. This paper explores the impact of uncertainties derived during testwork at key processing stages on the overall performance of mineral processing flowsheets. Case studies for both mineral sand and iron ore projects will be used to illustrate the concepts studied in this paper.

Jan 1, 2007

By P. G. Terrazas Prado

This paper presents the results of research on the development and application of a custom-made truck cycle and delay automated data collection system (TCD-ADCS) in a surface coal mining. Truck cycle and delay field data are locally stored in trucks and then synchronized and replicated through a wireless network into a centralized server containing an already-developed integrated production management system (IPMS). The system relies on motion sensing and distance travelled in order to automatically define the cycle starting/ending points, cycle time, position, and delay time. Connectivity and communication between loading equipment and trucks are also established. Communication between the equipment operators and TCD-ADCS system is via a user-friendly graphic interface. The hardware used for the development of this system consists of a rugged touch-screen personal computer, 2.4 GHz radio transmitter antenna, and a commercial GPS receiver. The system was developed, tested, and deployed at a surface coal mine in the USA. Keywords surface coal mining, truck and shovel, data collection, information systems.

Nov 1, 2013

By A. Madowe

This paper discusses the mine planning process for Letseng diamond mine in the Kingdom of Lesotho, in conjunction with the various software packages used during the process. The major pillars of the long-term mine planning process at Letseng are pit optimization followed by pit design and scheduling. Letseng uses Gemcom Whittle and GEMS for pit optimization and design and Runge XPAC for scheduling. The output of the mine planning process results in the generation of published mineral reserves and provides input into the Letseng overall business plan. The process of defining the key inputs for the entire mine planning process is discussed, which covers: ? Pit optimization ? Slope design as an input ? Diamond price inputs ? Operating and capital cost inputs ? Haul road design ? Generation of pit shells ? Selection of an optimum pit shell and interim cutbacks using operational scenarios ? Sensitivity analysis on the selected optimum pit shell. ? Pit design ? Slope design criteria in the detailed design ? Split shell vs concentric pit design ? Practical mining widths to determine cutback design ? Ramp design ? Pit design process in the GEMS software package. ? Detailed scheduling ? Development of scheduling scenarios in the XPAC software package ? Planning through mining production bottlenecks. ? Company-level NPV model ? Comparing scenarios and input of the different schedule scenarios into the company NPV model. Keywords pit optimisation, mine planning, pit shell, recovery, dilution, revenue factor, pit design, split shell, sensitivity analysis, scheduling, production bottleneck, NPV, discounted cashflow.

Jul 1, 2013

By N. X. Feng, S. G. Zhou, X. L. Wu, J. P. Peng, Y. Z. Di

"Szaibelyite–suanite type ore is rich in magnesium oxide and boron oxide. We propose a new method to extract both metallic magnesium and valuable residues rich in boron by reduction using metallic aluminium.Thermodynamic analysis of the reactions between aluminum and MgO, Mg2B2O5, and Mg3B2O6 was carried out. The effects of CaF2 addition, temperature, mass of Al, and pellet formation pressure on the extraction of magnesium were also investigated experimentally.The results indicate that the magnesium oxide phase can be displaced from 2MgO-B2O3 and 3MgO·B2O3 by CaO in the reduction system. The reduction ratio of magnesium oxide was 38% without calcium fluoride addition, increasing to 94% with 5.1% calcium fluoride. The reduction ratio increased with increasing temperature and mass of Al. To obtain a higher reduction ratio, the reduction pellet should be formed under a reasonable pressure.IntroductionBoron and its compounds are widely used in textiles, borosilicate glass, metallurgy, fertilizers, and nuclear shielding. Boron resources are mainly found in Turkey, the USA, Russia, and China. In Liaoning, China, there are abundant szaibelyite–suanite type ores that are rich in magnesium oxide and boron oxide. Szaibelyite and suanite ores are used to produce borax by a carbon dioxide– soda process. Annually, 2 Mt of waste materials containing 3–20% B2O3 and 2–25% MgO are produced during the process. It is necessary to make use of these waste materials containing high concentrations of boron oxide and magnesium oxide to avoid environmental problems as well as for economic reasons (Ozdemir and K1pcak, 2007)"

Jan 1, 2016

By D. Limpitlaw

Industrial mining in Zambia started in the 1930s when the world class copper deposits near the border with Katanga were developed. The discovery of these deposits began at the turn of the century when the first claims in the Copperbelt were pegged at Chambishi, north of what became the town of Kitwe1. World War I and the difficulties of raising sufficient capital for such large scale undertakings delayed the exploitation of these deposits. Following this hesitant start, a large copper mining complex was built, resulting in the development of five major towns, all highly dependent on the mining and beneficiation of copper and cobalt. Copper became so important to the country that, on independence, the only non-mining town to make it onto a list of the top six was the capital, Lusaka. From commissioning of the mines to the end of the colonial period in 1964, copper production increased to just over 640 000 t annually2 (see Figure 1). After the establishment of the new Zambian state, production continued to increase, supported by a benign legislative environment and strong international copper prices. The government of Kenneth Kaunda was intent on improving the conditions of the rural poor and reducing unemployment in urban areas. To this end, the government embarked on an ambitious project of refocusing Zambia's economy away from the colonial role of commodity supply to one of decentralized mass employment. The Copperbelt industrial complex was key to the success of this approach, and in 1969 the Zambian State acquired a 51 per cent stake in Zambia's two main copper producing companies: Roan Selection Trust and Rhodesian Anglo American Corporation. The former became Roan Consolidated Mines Ltd (RCM) and the latter became Nchanga Consolidated Copper Mines Ltd (NCCM). In the year they were nationalized, the mines produced at least 720 000 t of copper? and employed approximately 48,000 workers (see Figure 2)2-4. The subsequent economic policies of the Zambian Government depended heavily on the state's ability to monopolize the proceeds of copper mining.

Jan 1, 2011

By K. Richardson

Although the De Beers group has a long history of placer mining on land, the group only became actively involved in deep water marine diamond exploration and mining in1983 with the formation of De Beers Marine. Full-scale commercial mining commenced around 1991. Since then, the group marine mining capability has grown into a formidable fleet of 8 large deep water (>70 m) mining vessels, as well as other special purpose geo-survey platforms. Marine diamond production by the group is expected to be just short of 1 million carats in 2006. DeBeers operates across the entire value-chain spectrum from geology and geo-survey, through sampling to mining, and finally ore processing into high value concentrate. Supporting these operations involves significant service activities such as maintenance, security, logistics and environmental management. Specific challenges exist in terms of developing or acquiring appropriate technology for marine mining. These challenges have resulted in DeBeers operating extensive in-house R&D and projects departments, as well as drawing extensively from technology partners. An array of computational and test facilities are also available to support R&D and projects activities. Hydro transport in various guises is key to the current approaches to marine mining and ore processing. Use is made of airlift and centrifugal pumping for hydraulic hoisting of very coarse gravel, while splitters, launders, dewatering, elutriators, jet-pumps, centrifugal pumps, dense medium circuits, pipeline systems, and instrumentation for coarse abrasive particles are used extensively in the ore processing plant.

Jan 1, 2007

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

By T. G. Maepa

"The creation of mine excavations alters the stress distribution in the surrounding rock mass. In modern mining, resin-grouted rockbolts are used as a means of support in order to redistribute stresses and reestablish equilibrium in the rock mass. The success of resin-grouted rockbolting depends on the design of the system and the correct installation of the support units.The support design and rockbolt installation procedure at a platinum mine in the Bushveld Complex were investigated. A number of issues that resulted in poor installation were identified, including resin admixture, incorrect length and orientation of support holes, over- or under-spinning of the resin, and incorrect rockbolt tensioning. The support design used at the mine was reviewed and its limitations identified. A number of recommendations were made for optimizing the support design by reducing the diameter of the drill bit and reducing the length of the support holes. These changes will enable the mine to use different combinations of resin capsules. Implementation of the proposed changes will lead to a significant reduction in the cost of installation per support hole, as well as improve productivity and safety.IntroductionThe creation of any mine excavation disturbs the virgin state of stress in the Earth’s crust. This results in stress concentrations that interfere with the stability of the rock mass surrounding the excavation. It is essential to modify the internal behaviour of the rock mass surrounding excavations in order to reinforce the ground and stabilize excavations. Resin-grouted rockbolts are extensively used for this purpose. Esterhuizen (2014) stated that when effectively installed, the rockbolt exerts a clamping force and a bonding strength that keeps the rock mass together. This increases the cohesive strength of all discontinuities in the rock mass and enhances the stability of the excavation. Poorly designed and installed ground support is ineffective and constitutes a safety hazard. It is therefore crucial for every mine to ensure that any form of ground support is designed and installed correctly. This research evaluates the installation of resign-grouted rockbolts and identifies challenges and solutions for improved safety as observed at an operating hard rock mine. The support design used at the mine was reviewed and the design parameters optimized. The outcomes will enhance the efficiency of support and minimize the costs associated with the installation of resingrouted rockbolts."

Jan 1, 2017

By A. Sampson-Forsythe, P. Morissette, A. R. Punkkinen, D. R. Chinnasane

"The performance of ground support systems under dynamic loading is typically assessed in a qualitative and subjective manner. As a result, it is difficult to develop an explicit knowledge on the mechanisms of action and interaction of support elements subjected to rockbursts. This paper examines rockbursts that have occurred at Creighton, Copper Cliff, and Coleman mines since 2000, 2004, and 2006, respectively. The mines are located in the Sudbury Basin, in Ontario, Canada. The majority of pertinent information was obtained through on-site field assessments, seismic system records, and numerical elastic stress modelling. Passive monitoring is used to link the evolution of the frequency and severity of rockbursts to the evolution of mining and support practice at the three mine sites. Based on the collected data, ground support elements that enhanced the capacity of support systems to withstand dynamic loads are identified. IntroductionThe selection of appropriate mining methods, extraction sequences, rock mass de-stressing techniques, and ground support systems is of great importance in mitigating the level of rockburst-related risk. In burst-prone conditions, the design of support systems should account for the anticipated dynamic load demand and the capacity of the available support options. Furthermore, an economical design should, implicitly or explicitly, take into consideration the consequences of a rockburst and its impact on worker safety and mine productivity. Stacey (2012) has argued that we have a limited understanding of the mechanisms of rock mass behaviour in seismic conditions. This is compounded by a ‘lack of understanding of the mechanisms of action and interaction of support elements under dynamic loads’ (Stacey, 2012). Consequently, the design of support systems required to manage dynamic loads is usually based on experience. The assessment of the dynamic performance of ground support systems is typically subjected to qualitative (and sometimes subjective) interpretations from ground control personnel."

Jan 1, 2017

By U. W. O. L Vogler

"The behaviour of rocks depends on their material properties, and therefore it is important that these properties are determined by relevant and reliable laboratory testing methods. The ISRM Suggested Methods are very important documents in this regard, and a draft suggested method exists for the determination of the ’complete stress-strain curve for intact rock in uniaxial compression’. The method specifies the required geometry of specimens and the required testing procedures. The research described in this paper involved the determination of complete stress-strain curves for two materials, one exhibiting the Class I characteristic, and the other the Class II characteristic. To obtain a better understanding of the deformation behaviours in the post-peak region, tests were carried out on specimens of both material types with different length-to-diameter ratios. The results showed that the geometries of the test specimens influence the stressstrain curves in the post-peak region. The implication is, therefore, that the numerical values obtained for the slopes of the post-peak graphs are not material constants, but are geometry-dependent. Explanations for this behaviour are given. These findings have important implications regarding the use of post-peak data, for example for blast fragmentation considerations, and for evaluation of rockbursting potential. The research findings are based on a limited amount of laboratory testing, and should be confirmed by further testing. IntroductionThe most common approach for studying the behaviour of rock is by compression testing of cylindrical specimens in the laboratory. Rocks respond to forces by deforming and eventually breaking. The strength and the deformation characteristics are derived from the stressstrain curves produced. Standard shapes and sizes for the test specimens and standard loading rates are recommended in the Suggested Methods of the International Society for Rock Mechanics (ISRM) and the American Society for Testing and Materials (ASTM) standards. In spite of these standards, there remain certain aspects of testing which require further attention. The research described in this paper deals with deformation and failure behaviour of rock materials using stiff, servocontrolled testing equipment. The particular objective was to test the premise that the behaviour of cylindrical rock specimens in the post-peak region of the stress-strain curves does not reflect only a material characteristic, but is influenced by the height-to-diameter ratio (the geometry) of the rock specimen. An additional objective was to investigate the effect of the stiffness of the test equipment on the outcomes of tests."

Jan 1, 2016

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

The auriferous Carbon Leader reef which is the subject of this study can be subdivided into two types of sedimentological units, each with its characteristic spatial variability. For the longwall mining method applied at Western Deep Levels gold mine, subdivision of the orebody improves the estimation of the actual error variance, but not the grade estimates themselves. This can only be achieved by choosing oreblocks of a size and shape that are maximal parallel to the longwall and minimal at right angles to it, within the limits of mining restrictions. While simple kriging is the only method that gives unbiased results, the difference between untransformed and logtransformed kriging is negligible.

Jan 1, 1987