Search Documents

By Charles L. Kimbell

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom has been continued this year in tables 23 and 24. As a result of the lack of availability of comprehensive data on the prices of metals in Canada, the table that had presented that information in past years in this chapter has been discontinued and the price series for nickel that had been in that table now appears in the table presenting metal prices in the United States.

Jan 1, 1993

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By P. R. Bremner

The United States is more than 90 pct dependent on imported bauxite a source for aluminum, but it has vast nonbauxitic aluminum resources, such as kaolinite, anorthosite, alunite, etc. As part of a program to devise processes for treating these resources, the Bureau of Mines investigated a bench-scale leaching process using hydrochloric acid (HC1) and fluoride to extract aluminum from Wyoming anorthosite. HC1 and fluoride-to-aluminum (F/Al) mole ratios were studied with respect to aluminum extraction for single-stage, cocurrent, and countercurrent leaching modes. Using 95 pct stoichiometric HC1 and a F/Al mole ratio of 0.27, 90 pct of the aluminum was extracted by countercurrent leaching. Single-stage leaching with the same amount of acid and fluoride extracted 48 pct of the aluminum. Three fluoride sources, CaF2, Na2SiF6, and H2SiF6, were used and gave similar results on aluminum extractions.

Jan 1, 1982

By C. H. Elder, Maurice Deul

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coalbed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 ft3 /day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By Sabri Ergun

The method of constant compositions involves the determination of the time required for the attainment of a given conversion at various temperatures. Heretofore, it has been used in evaluating the energy of activation only. A development of the method, made in the present study, makes possible the evaluation of the functional dependence upon composition and the frequency factor in addition to the energy of activation. INTRODUCTION Kinetics of reactions are best analyzed in the light of the mechanism, energy requirements, and forces involved in the reaction. Such physico-chemical information is not often available in solid state phase transformations. The reaction rates are followed by changes in a physical property during the course of the reaction, and repeating the experiment at different temperatures permits the determination of activation energy only. The possibility of a complete kinetic analysis by such a purely "phenomenological" approach has been questioned.4/ In this report a method is developed making possible the evaluation of the functional dependence upon composition and frequency factor in addition to the energy of activation. The application of the method to a study of solid state order-disorder changes is demonstrated.

Jan 1, 1960

Develop design and support guidelines for coal mine entry intersections based upon results of integrated field and numerical modeling analyses of structural parameters for improving ground stability. Background Underground coal mines contain a large number of entry intersections. Dome-shaped zones over the intersections are unstable and are often associated with roof falls. These roof falls may occur during mine development, trapping equipment and endangering miners. These high-risk areas of the mine account for 10 pct of the total number of ground-failure-caused fatalities. The falls, ranging from heights of 1 to 20 ft, cause high dilution and slow the advance rates. Stability at intersections is influenced by four structurally interrelated parameters: in situ stress, geological discontinuities and physical properties, intersection geometry, and roof span. Because of the complex interaction of these parameters, the actual mechanism of roof failure may vary considerably, depending upon the roof lithology, rock strength, and stress conditions.

Jan 1, 1990

By A. B. Cecala

A cooperative research effort was established between the Tilden Mining Company LC, the United Steelworkers of America, and the National Institute for Occupational Safety and Health to lower respirable dust levels in an iron ore grinding and concentrator plant. This cooperative effort involved three field studies to evaluate different techniques to lower respirable dust levels. The greatest impact on lowering respirable dust concentrations throughout this facility was achieved through ventilation changes. The most significant improvement was realized by changing the ventilation profile throughout the entire facility. The ventilation to this grinding and concentrator facility was provided by approximately 40 roof fans operating in either the intake or exhaust mode. The operation of these fans was significantly changed in an attempt to pro-vide more of a directional flow pattern throughout the facility, as well as to more closely balance the intake and exhaust air volume. This change accounted for a 31 pct reduction in respirable dust levels in the primary grinding area of the mill. Another successful modification was to improve the sealing of a reclaim tunnel to the outside and by barricading the access point from the reclaim tunnel to the concentrator plant. This minimized the dust liberated in the conveyor tunnels from traveling through the reclaim tunnel and into the plant. These two modifications illustrate the impact that improvements in ventilation can have on lowering respirable dust concentrations in iron ore processing facilities.

By Suresh K. Bhatt, Gary L. Mowrey, Timothy R. Rehak, David K. Ingram

Coal and nonmetal mining used about 4.3 billion pounds of explosives and blasting agents during 2001 in the United States. A major part of this consumption was related to surface mining. Mine Safety and Health Administration accident data indicate that flyrock and lack of blast area security were the primary causes of blasting-related injuries in surface mining. Fatal injuries due to lack of blast area security were primarily caused by failure to clear blast area or inadequate access control to the blast area. At a coal mine, a neighbor walked into the blast area and was fatally injured. The blaster could not see the victim entering the blast area from the firing station. In another case, a passenger in a vehicle was fatally injured by flyrock because highway traffic was not monitored during the blast. In another example, a dozer operator entered a blast area due to lack of access control. Several fatalities resulted from using inadequate or no blasting shelter. A crane operator was fatally injured while standing in the open about 120 ft from the blast site. In another instance, a helper, standing about 150 ft away from the edge of a blast, was fatally injured by flyrock. In a limestone mine an equipment operator was fatally injured while guarding access roads in a pickup truck. This paper briefly describes six representative fatalities due to flyrock and lack of blast area security in coal and nonmetal mines. Several mines were visited to collect information relative to working practices aimed at mitigating blasting hazards. Salient information obtained through these visits is presented.

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

By John L. Reuss

A laboratory study was conducted by the Bureau of Mines to investigate the technical feasibility of decomposing hydrous magnesium chlorides by using a steam pyrohydrolysis technique. This procedure consisted of injecting steam into the atmosphere of a decomposition furnace containing samples of hydrous magnesium chloride and determining the rate of hydrolysis by measuring the rate of chloride evolution. The variables investigated were temperature, amount of water vapor in the decomposition atmosphere, and hydration stage of magnesium chloride. The application of steam was shown to accelerate both the rate and completeness of magnesium chloride decomposition reactions. For example, when magnesium chloride hexahydrate is exposed to a furnace temperature of 600' C in an air atmosphere for 20 minutes, the decomposition is 37 percent. Under identical conditions in a steam atmosphere, the decomposition is in excess of 70 percent. The magnesium oxide produced by the steam pyrohydrolysis of magnesium chloride dihydrate at 800° C contained 98 percent magnesium oxide. Based on magnesium oxide composition, this is equivalent to that of burned magnesite produced at temperatures in excess of 1,300° C. To demonstrate the quality of the product on a practical basis, metal reduction tests have shown it to be equivalent to reagent-grade magnesium oxide as a carbothermic reduction feed material.

Jan 1, 1974

Develop personal computer (PC) based software for analyzing and/or filtering time- and frequency-domain attributes of seismic and electromagnetic signals from geophysical surveys for the enhanced interpretation of rock masses and subsurface geologic structure. The Problem Both mining and petroleum geophysicists utilize seismic signals to characterize rock masses for delineating subsurface stratigraphy and structural conditions. However, a vast amount of information available in seismic project evaluation data often is unavailable for interpretation unless these data are enhanced. New processing technology increases the quality of these signals for analysis and interpretation. Comprehensive signal processing software is mostly written for petroleum exploration companies. Commercially available signal processing programs are often limited to a single application or are restricted for use with specific hardware, e.g., a digital oscilloscope or a mainframe computer. The programs may use computer codes that are proprietary, restrict user modification to expand capabilities, or may be hard to interface. They may have insufficient documentation for easy use and be support dependent.

Jan 1, 1990

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 4 Illustrative Simulations The capabilities of the program are demonstrated by simulating various evacuation cases in different situations for a particular mine. The mine selected for the illustrative simulations is the mine I C' , as described in Section 2, chosen particularly because of availability of mine characteristic data and mine evacuation results for test drills. These evacuation results can be used to verify validity of the predictions made by the program A.4 1 Mine Characteristics A schematic diagram of the mine is shown in Figure 19. The figure shows all the major shafts, drifts, raises and stopes of the mine in the form of a network. There are four hoists, Hoist No. 1 and Hoist No. 2 are assumed to be single drum hoists and Hoists Nos. 3 and 4 form part of a double drum hoist, with Hoist No. 4 being the main hoist (master hoist) The positions of the 133 miners, typically working in a day shift of the mine, are also shown in the figure. The miners are identified by a miner number, and their total number on each level is chosen from the data on the fire drill simulated as Case No. 1 in the illustrative simulations.

Jan 1, 1976

To develop and design a bit that will rapidly drill smooth and precise instrumentation holes in soft rock. Approach Use a one-piece bit made by combining a drag bit and a diamond bit. Because a smooth-walled borehole with a precise diameter is needed for borehole pressure cells (BPC) and other borehole instruments, a diamond bit is usually used. However, diamond bit drilling is slow, and the bit will tend to bind when squeezing ground is encountered. On the other hand, the drag bit will cut faster, but the walls of the drill hole will be rough and the diameter will not be as precise. The combination will provide a bit which penetrates as rapidly as a drag bit, but retains the smooth-wall and precise borehole diameter of a diamond bit. How It Works A three-foot-length of EW-size drill rod is centered in a diamond bit by welding it to three equally-positioned spacers at each end of the bit. A drag bit is attached to the EW rod with a standard EW-to-drag bit adapter as shown in the diagram. Three equally-spaced diamond inserts are set to the desired hole size and welded to the diamond bit barrel behind the crown. These inserts increase the smoothness and precision of the hole by cut-ting away any hole closure. Three equally-spaced shims are set approximately 0.020-inch under the overall insert diameter size and welded to the rear of the diamond bit barrel. The combination bit should be used on a diamond drill with either water, mist or air as the coolant.

Jan 1, 1982

Use instantaneous sampling to pinpoint dust sources and to Improve dust control on longwalls. Approach Use a dust monitor developed under a Bureau contract. How It Works Sampling can be done by either a moving or a stationary method. In the "moving' method, the dust monitor is carried by a survey engineer walking at the midpoint of the shearer Dust levels and face position (support number) are taken during all phases of the mining cycle while the shearer is cutting. These measurements can show how changes in airflow along the face, face specific; (rock partings) and cutting sequence (cutting the wedge) variables affect dust levels. In the "stationary sampling" method, the survey engineer stands with the RAM at a fixed location on the face. As the shearer approaches, the dust level and the distance to the shearer are recorded at 10-second intervals. Typically measurements start when the shearer is 20 feet from the sampling position and continue as the shearer passes the position until it is 20 feet away on the other side. Dust profiles around the machine are obtained at several fixed locations along the face only while the shearer is cutting.

Jan 1, 1982

Reduce face methane concentrations and help prevent miners from working under unsupported roof while moving the curtain. Approach Use water sprays on the continuous mining machine to move and direct air to the face, and also provide appropriate installation guidelines for the most effective use of the system. I n laboratory tests and under actual mining conditions, the spray fan has proved an effective means of ventilation. Recent observations in the field, however, have shown that not enough technical information is widely available on proper installation of the spray fan. This Technology News is designed to rectify that situation by providing a concise guide for spray fan installation. How the System Works Good ventilation is essential for methane control. The spray fan system repositions regular water sprays to help the normal exhaust face ventilation do a more effective job. The various water sprays help in many ways: 1. Side sprays bring clean air along the side of the miner into the off-curtain corner.

Jan 1, 1983

By J. J. Cummins

Green River oil shale previously extracted by benzene was heated at 150°, 200°, 250°, 300°, and 350° C for 0.5 to 360 days to determine the rate at which kerogen degrades to thermal products, the types of thermal products formed, and the effect of prolonged low-temperature heating (preheating) upon subsequent assay yields. Thermal decomposition of kerogen at 150° to 350° C is treated as a first-order reaction. The specific reaction rate for kerogen decomposition increases from 2.2 X 10-4 per day at 150° C to 2.0 X 10-1 per day at 350° C. The calculated kerogen activation energy is 19 kcal. Variations in the rate of formation of individual type components of the pyrolytic products were found. Carbon balances show an increase in the amount of kerogen converted to bitumen and oil (from assay of preheated oil shale) as the temperature of preheating increased from 150° to 350° C. Total product from shale preheated at temperatures of 150° and 200° C gave less than 100 percent of Fischer assay yields while the total products from shale preheated at temperatures of 250° to 350° C gave greater than 100 percent of Fischer assay yields.

Jan 1, 1972

By Marie Farnsworth

"The Anhydrite ProblemThe Nonmetallic Minerals Experiment station of the Bureau of Mines at Rutgers University, New Brunswick, N. J. has recently undertaken a study of the chemical and physical properties of anhydrite having in view its wider utilization anhydrite (CaSO4) in contact with water at ordinary temperature and pressure rehydrates, slowly forming gypsum (CaSO4.2H42O). In nature this is an extremely slow process, and laboratory experiments are being conducted to determine methods of accelerating the rehydration. The tests recorded herein cover one this study, and while they are negative in character in so far as the major problem is concerned, certain facts established by the tests, bearing on the stability relations of gypsum and anhydrite seem sufficiently important to be placed on record.Early Researches on Gypsum and Anhydrite.It is to Lavoisiar that we are the first scientific study of the calculation and hardening of plaster of Paris. He sums up his experiments in the following passage: ""If gypsum, which has been deprived of its water of by means of heat, is again treated with water (to make what is commonly called mortar) it takes it up with avidity, rapid and irregular crystallization occurs, and the small crystals which are formed are so entangled in each other that a very hard mass results."" Later, he observed that the dehydration of gypsum occurs in two stages: three-fourths of the combined water is much more easily driven out than the last fourth. LeChatalier first determined the temperature decomposition accurately, his method was as follows: Pulverized gypsum was placed in a glass tube in the middle of a paraffin bath, the temperature of which was raised in a progressive and regular manner. A thermometer gave at each instant the temperature the salt, and the passage of the mercury column past each division of —co. was cared by a registering chronograph. The rise in temperature was except at 128°C. and 168°C. where breaks occurred."

Nov 1, 1924