Search Documents

The Bureau of Mines evaluated short-delay coal mine detonators manu-factured by three domestic companies for electrostatic sensitivity, strength, and no-fire current level. Electrostatic sensitivity was studied in pin-to-pin and pin-to-case modes employing lO-kV potential. Strength of detonation was measured in the Bureau's underwater test fa-cility. No-fire current was measured using a constant-current power supply unit. Test procedures and experimental data are included.

Jan 1, 1985

By Forrest T. Moyer

THE SAFETY record of the mineral and mineral-fuel-mining-and-processing industries retrogressed slightly in 1964, as indicated by the 3-percent increase in the frequency rate of all injuries. A slight improvement in the fatality rate was more than offset by the less-favorable rate of occurrence of nonfatal injuries. The overall-operating activity of these industries was lower in 1964 as measured by slight declines in employment and total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 18.00 per million man-hours. This overall rate in 1964 comprised frequencies of 0.29 for fatal injuries and 17.71 for nonfatal work disabilities, which compared with respective rates of 0.30 and 17.20 in 1963. Fatalities totaled 538 or 30 less than in 1963. However, the total nonfatal disabilities of 33,151 in 1964 was 492 higher than in the preceding year.

Jan 1, 1965

By Rex D. Thomas

Concentration of the kerogen (organic material) in oil shale was accomplished by centrifuging after pretreating the oil shale with carbonic acid to remove the carbonates and pretreatment with sodium hydroxide (pH 11.5) to remove the claylike minerals. Analysis of the materials obtained showed that the concentrations of organic sulfur and organic nitrogen compounds were not affected by centrifuging. These compounds are evenly distributed in the kerogen and are not strongly bound to the mineral constituents. Organic oxygen compounds, however, were concentrated in the light fraction. These compounds are more closely associated with the kerogen and are not bound to the mineral constituents. Iron compounds other than pyrite apparently are closely associated with the organic material.

Jan 1, 1970

By T. C. Higgins, J. S. Malesky, J. A. O'Connor

"INTRODUCTION This circular contains the story of a stubborn mine fire of electrical origin that started on the main haulage road of No. 59 mine of the Peabody Coal Co. and illustrates that sometimes serious fires can be fought by direct attack. The story also points out that the cost of such procedure can be extremely high, and it is better, therefore, to minimize the possibility of a fire of electrical origin by suitable over-current and line-fault protection. The lives of 163 men were saved by utilizing a recently sunk air shaft near active workings as an escapeway. These men could not have reached the older openings. Also described are the rescue of 75 additional men through another air shaft, sealing of the fire, attempted extin¬guishment with carbon dioxide, and the difficulties of fighting the fire and recovering the mine.A fire occurred shortly before 12 o'clock noon, August 15, 1949, in the No. 59 mine, Peabody Coal Co., Springfield, Ill. All 257 men underground escaped to the surface. One group of 75 men was delayed from escaping for several hours after the alarm was given because smoke and fire gases were circulating in a main return airway, which intervened between their working section and one air shaft, and also in the stairway compartment of the shaft. After being supplied with universal-type gas masks, or self-rescuers, these men were conducted from the mine by members of a State mine-rescue team and other mine employees. Six nine officials were hospitalized because of exposure to carbon monoxide during fire-fighting activities; all were discharged a few days afterward. Later, while doing work incident to fighting the fire, two men were killed, and several were injured by falls of roof and rib.The fire broke out after a collision of a loaded trip with four empty mine cars on the main east haulage entry. The mine cars were jammed against the trolley wire causing a sustained electric arc that ignited the wooden mine cars and the fire spread to the timbers and coal."

Apr 1, 1950

By H. Robert Ensminger

As a result of the new mining law implemented in August 1985 and the programs conducted by the Institute Ecustoriano de Mineria (INEMIN), which was created by this legislation, there was considerably greater activity in the nonfuels mineral sector during 1986. Over the next 2 years, INEMIN will be developing a national mining plan that will guide Ecuadorean mineral development for the balance of this century. As stage one of INEMIN's mineral study, historical records were reviewed and 300 abandoned mines and 1,200 unexplored mineral deposits were available for further investigation. In 1986, INEMIN established 5 branch offices and negotiated 250 new mining contracts with foreign companies valued at $16 million. Despite all this activity, INEMIN officials estimate that 100,000 square kilometers remain available for claim staking. Technical assistance contracts were signed with Belgium, the Federal Republic of Germany, Italy, Spain, and the United Kingdom, to assist in a variety of assignments ranging from helping prepare the national minion plan to the development of industrial mineral deposits.

Jan 1, 1988

By C. H. Elder, Maurice Deul

Coal degasification boreholes drilled from the surface have been success - fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

By A. W. Effinger

The Bureau of Mines used regression analysis and applied statistical methods in an effort to rationalize the results of an experiment examining the effects of certain variables on carbon deposition in a reservoir for thermal recovery of petroleum. Although none of the 15 trials of the original experiment resulted in the response of weight-percent of carbon regarded by the experimenter as adequate, values calculated using canonical analysis in two trials yielded responses 33 and 54 percent higher than the minimum acceptable figure. The actual responses differed by less than 3 and 6 percent, respectively, from the predicted responses. Methods are described for defining a path of increasing response based on the minimum point and the response surfaces and for defining a set of values for the parameters in question, which result in increased response, A detailed explanation of the mathematical process used in this analysis is presented in the appendix for ease in computer programing the technique.

Jan 1, 1970

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the' applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

Develop a safe, efficient filter for removing diesel particulate matter (soot) from the exhaust of underground mining machines equipped with water scrubbers. Approach The Bureau of Mines and the Donaldson Company, Inc., jointly developed a low-cost, disposable, pleated-media filter (PMF) system. The system is intended for use on Part 36 permissible equipment or other machines equipped with water scrubbers. The PMF is installed downstream of the water scrubber to take advantage of the cool exhaust produced by the water bath. This demonstration system was tested on three Jeffrey 4114 Ramcars and a Wagner LST-5 scoop at Utah Fuel Company's Skyline mine near Scofield, Utah. Figure 1 illustrates a clean filter element being inserted into the canister on the Ramcar. How It Works The PMF system consists of a water trap, an optional over-pressure relief valve, filter canister, and PMF Under normal operations exhaust from a vehicle equipped with a water scrubber is heavily laden with water, especially on immediate startup of the engine. The water trap is designed to remove most of the water droplets from the exhaust before they enter the PMF, thus improving PMF performance. The over-pressure valve is designed to limit the exhaust backpressure by venting off some exhaust gas before the: filter. It is attached to the water trap upstream of the PMF. Figure 2 illustrates and shows a break out sectional view of the location of the PMF on the Ramcar.

Jan 1, 1991

By J. F. Barkley

"In the course of the Government's Fuel Economy Survey of its own power plants, studies and tests have been made of various oil-burning equipments under power-plant boilers. There are now many types of burners being offered in the relatively limited field of power-plant use. The majority of the types used may be grouped into two general classes- those using steam to effect the atomizing of the oil, and those using mechanical means.Burners using steam have had the most prominence in this field for a long period. The mechanical atomizing type of burner successfully applied on shipboard, however, pointed to a possible betterment in land work. The vision presented itself of a burner that would need no steam for atomizing that would permit of air inlets or registers compactly arranged as a part of the entire burner, and that would only require the natural stack draft usually available in land boiler furnaces. Hence, rather recently there has been much development along this line, resulting in various types of burners.In Table 1 are grouped test items chosen from many tests showing representative analyses of the products of combustion obtained with various burners installed in various types of furnaces. In all these tests the burners were handled by experts and represent practically the best attainable for that particular arrangement. The boiler efficiencies ranged from 70% to 80%. It will be noted that the burners using steam for atomizing were able to secure slightly better 002 and less 02 without the presence of CO."

Feb 1, 1926

By A. Visnapuu

High-grade synthetic rutile has been produced in the laboratory from domestic ilmenite concentrates by a new carbonyl process. The ilmenite was first reduced to convert the iron oxides to metal and then treated at temper-atures over 1000 C in high-pressure carbon monoxide (CO) to convert the iron to the pentacarbonyl. Rapid carbonylation was achieved in the presence of small quantities of selected promoters. Maximum iron removal occurred at temperatures between 110° and 130° C at CO pressures from 1,000 to 1,400 psig. Iron pentacarbonyl appeared as liquid and vapor in the reactor and could be removed by gravity flow and vapor transport. More than 90 pct of the iron was extracted in 2-hr experiments at pressures of 1,000 psig and above. The Ti02 product is porous owing to the removal of the iron, has the rutile crystal structure, and is suitable for chlorination. Waste disposal problems associated with the process would be minimal because the iron pentacarbonyl can be decomposed to produce iron powder or pellets for sale and CO for recycling.

Jan 1, 1973

By Fred N. Kissell

Experimental work by the Bureau of Mines indicates that when a coalbed is degassed by boreholes, the flow of methane may actually increase with time. This phenomenon appears to be the result of a relative-permeability effect; that is, the coalbed permeability to the gas increases sharply with decreasing water saturation. This report reviews the background of experimental evidence indicating a relative-permeability effect, and presents the results of a computer simulation of two-phase flow in coal.

Jan 1, 1975

By Paul T. Allsman

SCIENTIFIC inquiries concerning phenomena that may influence mining technology were widely publicized during the year. The deep-hole drilling project "Moho," 3 the use of nuclear explosives underground, and the recovery of minerals from the depths of the sea became subjects of scientific and general discussion. The mining industry continued to watch these developments with keen interest: but its more immediate concern was the increasing tempo of competition between mineral commodities, the domestic producers of these commodities, and foreign sources of supply. The competitive situation has intensified the industry's efforts to develop more efficient new mining methods, as well as to improve the efficiency of present practices. The attitude of the industry was well illustrated by rapidly expended use of low-cost ammonium nitrate explosives, the establishment of rigid schedules for equipment maintenance, and close attention to the detailed costs of production. The complexity of planning a new coal mine is aptly illustrated by the editors of Mechanization in the April 1959 Issue, in which they outline the cost of developing a mine and the various problems, factors, and decisions involved.4

Jan 1, 1960

By J. J. Cummins

The Bureau of Mines heated at 150° to 350° C for 0.5 to 360. days Green River oil shale that had been previously extracted by benzene to provide information on in situ processing conditions, to determine the effect of low-temperature heating on the unconverted kerogen, and to determine the composition of benzene-soluble thermal products. The methods used in determining the composition of the soluble thermal products consisted of fractionation of the soluble material, elemental analysis of the soluble products, fractionation of the polar resins by ion-exchange chromatography, gas chromatographic analysis of [n]-alkanes3 and mass spectral analysis of the branched plus cyclic alkanes and aromatic oils. The methods used to determine the effect of low-temperature heating on the unconverted kerogen remaining in the oil shale heated residues consisted of carbon-hydrogen analysis, volatile material determination, carbon residue determination, and oxidation rate determination. In general, it was concluded that significant increases in the degradation of kerogen to oil occurred between the temperature range of 250° to 350° C; that the composition of the soluble products depends upon the temperature at which they are formed; and that the [n]-alkanes are pyrolytically degraded from the kerogen structure. In particular, the 250° C heating temperature is beneficial to the formation of branched plus cyclic alkanes. Also, the heated and unconverted oil shale kerogen and the soluble thermal products become more aromatic as the temperature increases from 150° to 350° C.

Jan 1, 1974

By H. K. Sacks

The Bureau of Mines has improved a mine dust incombustibles analyzer originally developed at the Bartlesville Energy Research Center (BERC). This analyzer provides quick, accurate analysis of the percentage of incombustible material present in dust samples taken from mine ribs, roof, and floor so that costly overdusting may be eliminated while still maintaining a proper level of incombustibles. The changes being effected on the present design of the BERC model IV rock dust analyzer should simplify its operation and calibration procedures, resulting in increased accuracy.

Jan 1, 1976

Enhance the critical skill of hazard recognition among miners by providing quality training that can help jot performance and lead to a higher degree of safety in the workplace. Background In mining, as in many other occupations, the safety of the worker depends on his or her ability to recognize hazards in the workplace. Some of the information needed by the miner for recognizing potential areas of danger is available in the form of visual cues found throughout the mine. One aspect of the dynamic mine environment it which the task of hazard recognition is critical for al workers is that of ground control. Regardless of job responsibilities, every worker is continuously exposed to roof rib, and floor hazards. Fatality injury data for the "underground coal" segment of the mining industry continue to show that about half of all fatalities are due to falls of ground each year. It is hypothesized that some of these accident, can be prevented if miners are better able to recognize visual cues that forewarn of potential roof and rib problems.

Jan 1, 1992

By Helen W. Lang

The Bureau of Mines has developed a very rapid gas chromatographic method for routine determination of oxygen, nitrogen, methane, and carbon dioxide in mine atmosphere samples. Analysis is accomplished in 3 min; readout appears on a single strip chart. The gas sample is split between two columns contained in separate chromatographs. A 5 A molecular sieve column separates oxygen, nitrogen, and methane; a porous polymer column separates carbon dioxide from an air peak. Direct selective analysis of methane from this unresolved air peak is accomplished using a hydrogen flame ionization detector (FID). Carbon dioxide is catalytically converted to methane and detected by FID.

Jan 1, 1972

By R. L. Grayson, W. E. Wallace, J. W. Stephens, M. D. Attfield, P. S. Brower, V. Vallyathan, M. J. Keane, J. C. Harrison

Pure respirable quartz is a known pathogenic agent for lung disease. However, for mixed dusts, neither mineralogical nor in vitro cytotoxicity assays unequivocally predict the contribution of quartz to their pathogenic potential.First, although Coal Workers' Pneumoconiosis (CWP) and Progressive Massive Fibrosis (PMF) prevalence have been found to correlate with total respirable coal mine dust exposure, and with coal rank (Attfield and Morring, 1992), epidemiological studies generally have not found the quartz component of coal mine dust as measured by X-ray diffraction or infrared spectroscopy (each of which essentially measures the mass-percent quartz in a bulk sample) to be clear predictors of CWP prevalence or incidence (Walton et al., 1971). Second, the properties which distinguish the extreme fibrogenic potential of quartz are not revealed by conventional in vitro bioassay comparison with other silicate mineral dusts. As an example, quartz and kaolin (aluminosilicate) clay in vitro cytotoxicities are comparable for lavaged primary pulmonary macrophages.The studies discussed here address these two anomalies from a general hypothesis that the pathogenic activity of respired quartz particles is associated with properties of, and interactions with, the particle surfaces. One factor in the expression of toxic activity by a particle surface is the biological availability of that surface. Anomalous lack of correlation of disease prevalence with mass percent quartz in exposures to some mixed composition respirable-sized dusts suggests that individual particle surface features, invisible by bulk sample mass analysis, may alter the biological availability of a fraction of quartz particles in a dust. For pure-surfaced mineral particles, the comparably strong prompt membranolytic activities of quartz and kaolin in vitro suggest that upon deposition of such particles in the lung there must be other interactions with particle surfaces which distinguish quartz. This might be due to toxic surface-associated sites specific to silica, or to interactions of other sites on other mineral particles which affect the biological availability of their toxic functional groups. For example, alurninol groups on clays affect the availability or activity of adjacent silanol groups. Surface activities which distinguish quartz pathogenici ty might be manifest in one or more of the sequential interactions upon deposition in the lung; first with the pulmonary surfactant system, then with extracellular and phagolysosomal enzymatic digestive processes, or with subsequent cytotoxic processes.

Dec 1, 1995

By Stephen A. Hare, O&apos

The melting, casting, and welding of the Raney nickel alloy (42 pct Ni-58 pct A1), a methanation catalyst useful in coal gasification, were investigated. Melting was done in graphite crucibles by heating aluminum and adding nickel using a cryolite slag cover. Casting conditions were found to be optimum when the melt temperature ranged from 1,125° to 1,200° C and the mold temperature ranged from ambient to 250° C. Suitable mold materials were found to be quartz, heat-resistant glassware, olivine, and zircon. Welding of the alloy can be accomplished using tungsten inert gas process. Tensile strength of the alloy, in the as-cast condition, was found to be 2,000 1b/sq in with an impact strength of less than 1 ft-1b. The coefficient of thermal expansion was determined to be 18.4 x 10-6/° C after heat treatment.

Jan 1, 1977

By Ronald D. Hill, Elmore C. Grim

The United States is richly endowed with mineral resources. However, mineral recovery by its very nature, involves a destructive process, Figures 1 and 2. In the past, mining practices were all too often conducted with the purpose of removing minerals by the simplest and cheapest method possible, without plans for the preservation of land, water, and air, and with too little consideration for the rights of others. A mining company is in business to make a profit, but every company, regardless of the nature of its business, has moral obligations to reduce its undesirable effects on the environment and to safeguard the rights of others. The problem of environmental degradation caused by surface mining is widespread and serious. Minerals in some form occur in each of the 50 States and several States are extensively mined. Data on the acreage disturbed in the United States, by commodity and State are presented in Table 1. Thirty-one States have laws regulating surface mining, (Table 2). Briefly reviewed in Appendix A-1 are the basic provisions of State laws governing surface mining. It can be seen that these laws vary considerably from State to State owing largely to the mining conditions within that State. Of the 24 coal-producing States, only three (Alaska, Arizona, and Utah) do not regulate strip mining. Even the states that are often cited as models of comprehensive regulations still have problems minimizing environmental damages. Uncontrolled surface mining presents a situation as critical to the well-being of the society as any it has ever faced. Many mining activities have imposed huge social costs on the public at large. These costs are long-range and are in the form of stream pollution, floods, landslides, loss of fish and wildlife habitats, unreclaimed land, erosion, and the impairment of natural beauty. In a 1965 Department of Interior study,(1)it was estimated that of the 25,000 miles (1+0,225 kilometers) of contour bench in Appalachia, approximately 1,700 miles (2735 kilometers) are affected by massive landslides. Additionally, 1+800 miles (7723 kilometers) of streams and 29,000 surface acres (11,716 hectares) of impoundments and reservoirs have been seriously affected by coal strip mining operations in the United States.

Jan 1, 1974