Search Documents

By Frank B. Fulkerson

Aluminum production in the Pacific Northwest has a new potential for expansion and increased stability of operation. This new potential results from greater availability of power; lower freight rates on alumina and aluminum; good market prospects for the metal, including western aluminum market expansion following a decline in defense requirements in the 1950's; and possibility of developing bauxite deposits in the Pacific Basin as well as other mineral resources. INTRODUCTION This is a report of a special study by the Bureau of Mines of the primary aluminum industry of the Pacific Northwest. It outlines developments relative to the United States as a whole.

Jan 1, 1962

By Stephen D. Cramer

The Bureau of Mines conducted a study in which the magnetic fraction of urban refuse was used as melting stock in the preparation of high-strength, low-alloy and carbon steel. Product steels, made from incinerated steel can scrap, nonincinerated-nondetinned steel can scrap, nonincinerated-detinned steel can scrap, and dilutions of these scraps with No. 1 heavy melting scrap, were used in continuing tests in industrial, rural, and marine environments to determine the effect of residual elements and atmospheric pollutants on their atmospheric corrosion resistance. The respective commercial steels were exposed at the same time to establish baseline corrosion data for the test sites. Weight-loss data are reported for atmospheric exposures of 0.5, 1.0, 1.5, and 3.8 years. The marine environment was the most corrosive; the industrial environment was the least corrosive. The atmospheric corrosion resistance of the carbon steel was improved 25 pct by using incinerated scrap and nonin-cinerated-nondetinned scrap in the steelmaking process. In no case was the atmospheric corrosion resistance of carbon steel degraded by using the magnetic fraction of urban refuse as melting stock. The presence of sulfur in the corrosion film was the most important factor affecting the corrosion resistance of the steels. With increasing sulfur concentration, the rate of the corrosion reaction was reduced and the corrosion film became more protective. The residual elements in the product steels most responsible for improving corrosion resistance were copper and tin. These elements tended to increase the concentration of sulfur in the corrosion film. At the levels present in the product steels, Cr, Ni, and Pb had no observable effect on the corrosion resistance of the steels.

Jan 1, 1980

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

Bitumninous and semianthracite coal reserves underlie about 1,400 square miles of Arkansas, less than 2.7 percent of the state's total area. These deposits, located near the western border, contain an estimated 2.2 billion tons, of which about half are recoverable. This represents less than one-tenth of one percent of the national reserves. Most of the commercial coal is mined from thin beds that are at least 14 inches thick. In some locations, however, the coal beds can be as much as eight feet thick. Lignite was mined in southern Arkansas before the Civil War. Current estimates indicate that the reserves may be as high as 9 billion tons, which could be used in the state's coal-fired electric generating plants; however, these deposits are not being mined at present. Because many coal operations in Arkansas are small and the demand for coal is unsteady, the industry employs fewer than 25 miners on a daily basis. Arkansas gained primacy when its regulatory program was conditionally approved November 21,1980, subject to the correction of four minor program deficiencies. The regulatory program was fully approved January 22, 1982. Authority of the state to administer its Abandoned Mine Land Reclamation Program was granted upon approval of the Arkansas Reclamation Plan on May 2, 1983. Arkansas was the first state to assume responsibility for abandoned mine land emergency projects when its Reclamation Plan was approved.

Jan 1, 1992

By John D. Sullivan, Alfred P. Towne

"In copper percolation-leaching plants the ore is usually crushed to a maximum size of about three-eighths inch. Ordinarily an ore is crushed as finely as feasible since the rate of extraction of copper is increased with decreasing size of particles owing to the greater surface exposed and. the shorter path required for solutions to come into contact with the minerals to be dissolved. However, greater degree of crushing also increases the amount of fines. When ores are charged into leaching vats the coarse and fine material tend to segregate, resulting in channeling of solutions and leaving the areas where fines predominate only partly leached. An improvement in the method of charging the ore into vats that would minimize the deleterious effects of the segregations of fines would increase the percentage extraction of copper.The Inspiration Consolidated Copper Co.4 recently installed classifiers to remove the primary slimes from the ore, before charging it into the leaching vats. This necessitates a separate agitation treatment for the slimes.Recent publications5 of the bureau have shown the advantages of agglomeration followed by trickle leaching to extract copper from concentrator tailings. It was shown that when equal parts of ore crushed to about 1/4-inch size and concentrator tailings were agglomerated with approximately 10 per cent of moisture, either in the form of water or leaching solution, and the mass was charred into a leaching vat the ore could be treated successfully by open-drainage trickle leaching. Even with 30 or 35 per cent of minus 200-mesh material present the ore could be leached, if it was not flooded with solution.The results obtained in agglomerating ores and slimes suggested the possible advantages to be gained by wetting the crushed ore for standard percolation-leaching plants before charging it into the vats. Wetting the ore whould make the fine material and slime cohere to the larger pieces of ore thus tend to prevent segregation when the ore is charged into the vats. The bureau, at its southwest Experiment Station and in cooperation with the Department of Mining and University of Arizona, Tucson Ariz., therefore made a study to work: out A way in which slimes could be handled in percolation leaching. The study showed that the method of charging ore into the leaching vats governed the distribution the fines and consequently the rate extraction of copper. The results of the study reported in this paper."

Feb 1, 1931

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By J. W. Thompson

ORES PROCESS OF ORE CONCENTRATION-PATENTABILITY. The patent issued to Sulman, Pickard, and Ballot, November 6, 1905, and assigned to Minerals Separation and Minerals Separation American Syndicate, for new and useful improvements in ore concen- tration, its object being to separate metalliferous matter from gangue by means of oils and fatty acids that have a preferential affinity for such metalliferous matter, the principal feature of which is "agitat- ing the mixture to cause the oil-coated mineral to form a froth," was clearly anticipated by other patents, and each step in the process described in the Sulman, Pickard, and Ballot patent is fully described in more than one of the prior patents, with the single exception of the reduced quantity of oil used; but the discovery that the small fraction of oil is sufficient to produce flotation of the metalliferous matter can not be made by itself or in combination, the subject of a patent. Hyde v. Minerals Separation, 214 Fed., 100, p. 109, May, 1914. ACTION FOR CONVERSION OF MINERALS. In an action by the grantor of a certain mine and mining property against his grantee to recover damages for the conversion of a quantity of ore that the grantor before the conveyance had mined and extracted from the mine and placed on the dump near the mine, the plaintiff is not entitled to recover where it appears that at the time the ore was placed on the dump the mine was owned and operated by a mining company and that at the time the ore was taken out of the mine the company had no intention of doing anything with it but simply deposited it on the dump as waste and to give an opportunity to develop the mine and get better ore to send to the smelter, and that

Jan 1, 1915

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By R. G. Knickerbocker, T. E. Evans, D. R. Torgeson

"INTRODUCTION Sponge iron is a product resulting from the reduction of an iron oxide at such a low temperature that fusion does not occur, and the reduced particles retain substantially the same shape as the original ore. The removal of oxygen in the reduction process leaves the metal porous and reactive. Sponge iron may be compared in general to a chemically precipitated substance insofar as reactive properties are concerned. The high specific surface and the orientation of metallic structure are factors which probably contribute to the reactive properties of sponge iron.The term ""gaseous reduction,"" as applied to iron ores, required clarification. Strong evidence exists, for example, that ore is partly reduced to sponge iron by carbon monoxide in the blast furnace at temperatures around 800° C. at a point that may be as high as 30 feet above the tuyores. In 1923 and 1924, Sims and Wood attempted to reduce iron oxide with carbon in an Arsem vacuum furnace at 980° C. These investigators found that only 6 percent of the iron was reduced to metal when the iron oxide-carbon mixture was heated for 1 hour under evacuated conditions, whereas at atmospheric pressure 70 percent of the iron was metallized. Their results indicate that the process of iron-ore reduction at temperatures below the melting point of the ore may proceed largely, if not entirely, by the action of reducing gases even when the reducing agent is solid carbon. Therefore, the term ""gaseous reduction,"" as used heroin, is defined as a process in which iron ore is brought into intimate contact with a reducing gas produced in separate-equipment from the reduction chamber itself.A large amount of pilot-plant development on gaseous reduction of iron ores has been carried out by the Bureau of Mines at the Boulder Experiment Station and had as its objective the reduction of fine iron ore by means of producer gas. The use of use gas was prompted by two considerations: First, the possible utilization of large reserves of Western noncoking bituminous coals and lignites contiguous to iron-ore drewwing; and second, an investigation of the results that might be achieved in the pilot-plant gaseous reduction of fine iron ores by means of a relatively reducing gas. The results obtained, it was felt, would be of considerable value in indicating the direction which gaseous reduction experimentation must take for the development of a commercially practicable and economic process for the production of sponge iron."

Dec 1, 1946

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

This manual provides instructions for installling, operating, and maintaining protective canopies on the Joy Mfg. Co. cutter. These instructions are based upon two actual installations: one made in a mine and one in the factory. The parts list and engineering drawings for the protective canopies are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other cutters with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other cutters and can determine any necessary modifications if they are not.

Jan 1, 1973

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

By John C. Edwards

A computer program, developed for the Bureau of Mines under contract, predicts in a quasi-steady-state approximation the ventilation and contaminant concentrations and temperatures when a fire occurs in a multi-level mine. For periods of time in which there is no significant change in the ventilation, yet a fire is producing fumes, a real-time fume concentration throughout the mine is calculated. Multiple and time-variable contaminant sources can be simulated. Recirculation paths that can develop provide a mechanism for increasing the fume concentration in the mine network and are identified by the computer program. This report contains a listing of the Fortran computer program as well as the required format of the input data. Two examples are provided of the real-time spread of smoke from a fuel-rich fire throughout a multilevel mine. The first example considers an operational exhaust fan as well as a booster fan. The second example evaluates the real-time smoke spread following a failure in the exhaust fan; recirculation occurs in this latter case.

Jan 1, 1982

By J. D. Davis

On May 15, 1936, Congress authorized the Bureau of Mines to conduct certain studies, experiments, and. investigations of subbituminous coal and lignite.4/ Appropriations were made in July 19 7, and since that date an active investigation has been underway to complete the provisions of the act. Part of the investigation has included a comprehensive survey of the known properties of the lower-rank non-coking coals, and provisions were made to obtain more data on certain varieties. In line with this plan, a typical subbituminous coal was selected for an extended series of tests in the standard. Bureau of Mines-American Gas Association unit,5/ at the Central Experiment Station. This particular noncoking coal was the first one of its rank that had been tested in the apparatus; for this reason the results are of particular interest because the testing apparatus was originally designed for use in studying the coke- and gas-making properties of coking coals. The test as described below has been developed by the Bureau of Mines since 1927 through a cooperative agreement with the American Gas Association.6/ Ninety to 180 pounds of coal is heated in a circular retort, 13 to 18 inches in diameter, at wall temperatures ranging from 500°C. to 1,110°C. in 100°C. steps. All products are collected and measured; their physical and chemical properties are then carefully determined to ascertain the gas- and coke-making properties of the coal. During the last 10 years approximately 50 representative American coals have been tested in the Bureau of Mines equipment. The results on the first 30 coals and a complete description of the test procedure are contained in a joint publication of the Bureau of Mines and the American Gas Association.7/ The remaining twenty coals have been reported in Bureau of Mines reports as Technical Papers and Bulletins.

Jan 1, 1939

By E. P. Youngman

The rapidly growing demand for titanium pigments has aroused new interest in actual and potential sources of supply of titanium- bearing ores , which only a comparatively few years ago were almost unmarketable . This paper , which supplements a general circular entitled " Titanium" ( Information Circular 6365 ) , represents a summary of current trade literature and Government reports , together with some hitherto unpublished material that has accumulated in the files of the Bureau of Mines . The purpose of this pamphlet is simply to indicate the commercial possibilities of the deposits , and the discussion is confined almost entirely to the three commercial ores , ilmenite , rutile , and magnetite ( titaniferous iron ore ) .

Oct 1, 1930

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By Doerner H. A.

From thermodynamic calculations Maier predicted that zinc oxide and methane would react at specified temperatures substantially according to equation (1). (1.) ZnO + CH4 = Zn (gas) + CO + 2H2. Other reactions that may take place are (2.) CH4 = C + 2H2. (3.) ZnO + CO = Zn (gas) + CO2. (4.) ZnO + H2 = Zn (gas) + H2O. Maier predicted that 870°C would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C. Theoretical considerations indicate that reaction (1) is reversible: this is supported, but not proved, by experimental data. The other reactions are known to be reversible. At low temperatures reaction (2) requires a catalyst and it is slow below 1000°C. Reactions (3) and (4) are rapid, but the equilibrium constants are such that only small concentrations of CO2 or H2O can be produced below 1000°C. Maier calculated that CO2 should not exceed 0.5 per cent at 870°C., and the calculation for water vapor gives a still smaller order of magnitude.

Jan 1, 1931

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By George A. Page, Hewitt Wilson, Vance S. Cartwright

"Purpose of InvestigationThe process of removing solid material from liquid suspensions has been studied at the Northwest Experiment Station, United States Bureau of Mines, in cooperation with the University of Washington, as part of a general program to investigate the dewatering of Pacific Northwest plastic kaolins, which is difficult by ordinary filter-pressing methods. The present paper is a progress report of the work began by Vance S. Cartwright in 1928 and continued in 1931 and 1932. Spray evaporation is believed to be valuable for the following classes or grades of clay and clay mixtures:(1) Highly colloidal, plastic-type clays, which release their mechanically attached water with difficulty; (2) clays prepared for shipment in pulverized or powdered condition; and (3) synthetic, ceramic, porcelain, and tile mixtures prepared as aqueons suspension, dried and pulverized before molding. Dilute suspensions can be dewatered by spray evaporation to produce concen-trated casting slip or plastic clay with a lower water content.The most common dewatering method used in preparing powdered kaolin for the market comprises the following steps: Reduction of the water content by filter-pressing from approximately 75 percent in the thick ""slip"" condition to about 30 percent in the condition; further reduction of the water in the filter-press cakes by heat to about 5 percent; and pulverization of the dried cakes in hammer or dust. These three steps can be simplified to a single process by spray evaporation."

Jan 1, 1935