Search Documents

By P. S. Lewis

Shortage of natural gas is reviving interest in low-Btu fuel gas made by gasifying coal in fixed-bed producers. The Bureau of Mines gasified strongly caking Pittsburgh bed coal over test periods lasting four days in an experimental gas producer located at Morgantown, W. Va, Mechanical stirring throughout the fuel bed was effective for keeping the fuel moving and this stirring made the operation successful; hence, the gas producer was named the stirred-bed producer. Nuclear density gages were applied as control instruments to indicate coal flow and fuel level, and to record the frequency and location of void spaces in the bed, The gas, of nominal 140 to 165 Btu/scf calorific value, could be burned in a boiler for generating steam.

Jan 1, 1972

By F. E. Cash

Much has been written concerning accidents in coal mines; the fact that accidents cost the employer and employee money is generally well known, but how much accidents actually cost is vague, even in the minds of many operators. Unquestionably there are hazards in coal mining, but many of them can be eliminated; and from the prevention of accidents there can be realized a material saving in dollars and cents as well as in human suffering. In presenting the frequency, severity, and cost of accidents in some Tennessee coal mines, it is hoped that other mines in Tennessee, as well as mines in other States, will by a comparison of the data with their own ex¬ perience be enabled eventually to reduce the number of' their accidents.

Dec 1, 1932

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on massive sulfide copper-zinc and low sulfide vein gold deposit types that may be found in the Ketchikan Mining District. Reserves and recoverable metal values (RMV) needed to make these deposits economically viable were modeled. Methods for estimating ore grades and required RMV are presented. Economic modeling for massive sulfide deposits indicated the RMV necessary for a 15% Discounted Cash-Flow Rate-Of-Return (DCFROR) for an underground cut-and-fill mine ranged from $137/mt for a 6,100 mtpd on-site milling operation to $526/mt for a 450 mtpd off-site milling operation. On-site milling was always less costly than off-site milling. Economic modeling for low sulfide vein gold deposits indicated the RMV necessary for a 15% DCFROR for an open-pit mine, off-site mining operation ranged from $S4/mt at 2,900 mtpd to $71/mt at 360 mtpd, and from $49/mt at 2,900 mtpd to $100/mt at 360 mtpd for an on-site milling operation. Off-site milling was less costly than on-site milling until production exceeded approximately 1,700 mtpd. Then, economies of scale reduced operating costs enough to offset the higher capital costs required for on-site milling.

Jan 1, 1995

By G. W. Weems

The Bureau of Mines combined preconcentrating techniques and mass spectrometry to develop a parts-per-billion general analysis of impurities in helium. The impurities are preconcentrated using a Bureau trace-impurity analyzer; 35-mm Hg pressure of helium is left in the concentration trap to sweep the impurities into the mass spectrometry and provide a 10-mm Hg sample pressure.

Jan 1, 1966

Develop a dry dust collector suitable for working faces and belt transfer paints. Approach A filter cartridge with a reverse-pulse, self-cleaning system has been mounted in-to a low profile unit requiring electric power only. How It Works Dust-laden air entering the in-let end of the collector passes through the two inline filter elements. When the elements load to a pre-selected pres-sure drop, they are automatically pulse-cleaned by a "backflush" method using compressed air. When the elements are pulse-cleaned, caked dust material on the filter surface is released, and falls away as lumps. Dust is removed from the collector by an auger mechanism. Features of the collector are: (1) unit is completely self-contained, (2) built-in air compressor for pulse-cleaning, (3) cleaning cycle initiates automatically at a preset restriction, (4) automatic auger discharge of collected dust, (5) detachable extension auger for transporting collected dust, (6) "dust leak" indicator light, and (7) "change filter element II warning light. The collector has been designed as permissible although approval has not yet been granted.

Jan 1, 1981

By S. L. Weber, Y. H. Cheng, D. E. Banks, J. K. H. Ma

"The aggressive industrialization of America, the development of powered tools which generated massive amounts of respirable-sized dust particles, a latency period which may mask the relationship between exposure and development of disease, inadequate (or perhaps even careless) understanding of the relationship between dust exposure and disease, and respiratory protection which has later proven to be inadequate have resulted in a series of epidemics of silicosis which have caused the premature death of many workers.1-11 Emphasis on the regulatory control of dust levels in the workplace has greatly reduced the development of pneumoconiosis in the United States and in other developed as well as underdeveloped countries, yet the prevention of silicosis or coal workers' pneumoconiosis has not come close to being accomplished. Despite the public health perspective that pneumoconiosis arc totally preventable illnesses, there appears to be little evidence that this is the case.Cases of pneumoconiosis continue despite aggressive enforcement policies by regulatory agencies, attempts at dissemination of very readable materials aimed at workers and management 12.13 and respiratory dust exposure standards which are in place and appear, for the most part, protectivc.14- 16 It is more than frustrating for all parties associated with advocating workers' health to see reports of workers with aggressive silicosis. On another level, both the physician and the affected worker are helpless when a diagnosis of silicosis or coal workers' pneumoconiosis is made. Both realize that there is no proven way to affect the natural history of these progressive inflammatory and fibrotic processes. Neither is there any ""compassionate use"" therapy. What must be developed, at the very least, is a ""salvage therapy"" which has the potential to reverse, or at least dramatically lessen, the aggressive natural history of silicosis which develops over relatively short time periods. Because of the aggressive nature of silicosis (compared to coal workers' pneumoconiosis) attempting to develop a therapy for this illness should be a priority."

Nov 1, 1995

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945

By Guy A. Johnson

Combining contract and in-house research, the Bureau of Mines has developed and inmine-tested a novel device to improve the field-of-view of operators of off-highway mining equipment. This device utilizes a downward-looking, flat fresnel lens. The lens, plus louvers to reduce glare, is housed in a protective steel structure. The complete unit is called a blind area viewer. The viewer, when mounted on the right- front corner of the deck of most large haulage trucks, will increase a driver's direct field-of-view from about 35 pct (of where he/she has to drive) to about 80 pct. The improved visibility allows the driver to see possible collision hazards and roadway obstacles better, thus improving mine safety and increasing productivity. Economic analysis shows that the blind area viewers, which are now commercially available, pay for themselves in about a month on a 170-ton-capacity truck. The viewers are also applicable to other large mining equipment, such as front-end loaders, draglines, and downhole drills, or any place where seeing around a corner would be advantageous, such as along conveyor flights in processing plants during startups.

Jan 1, 1983

By Raymond M. Stateham

A portable, handheld infrared scanner has been used to detect abnormal surface temperature on dumps of flood-generated trash near Wilkes-Barre, Pa. Three of eight dumps examined had thermal anomalies on the surface, indicating temperature buildup at depth. The anomalies found with the scanner were verified by measurements with a thermocouple probe or a carbon monoxide detector. One week after the investigation was completed, open fire broke out at the site of one of these thermal anomalies; about 6 weeks after the investigation, a thermal anomaly in another dump was verified when a trench was excavated in the dump.

Jan 1, 1973

By A. B. Campbell

The Bureau of Mines is developing alloys using ion implantation as an alternative to bulk alloys that consume large quantities of strategic materials such as chromium and nickel. These alloys are formed at the outer layer of relatively common materials. To more fully understand the corrosion characteristics and physical properties of this outer layer, it was necessary to deter-mine the alloy concentration as a function of depth into the substrate material. Also, since many of the ion-implanted alloys would be utilized at elevated temperatures, it was necessary to determine the diffusion behavior of the implanted element. Proton-induced X-ray emission and inert gas ion sputtering have been utilized to generate composition depth profiles for Fe-Cr, Fe-Ni, and Fe-AI ion implanted alloys fabricated by implanting 25-kev Cr+, Ni+, or AI+ into iron substrates. The data were fitted (utilizing a computer program) with symmetrical Gaussian profiles yielding values for the range and range straggle of the ions. These parameters were then compared with those calculated from theory. Changes in the profiles due to annealing were investigated and values for the diffusion coefficient were obtained assuming diffusion according to Fick's Law. For the Cr+ and Ni+ implantation, the profiles as-implanted agree reason-ably well with theory and exhibit ?norrmal" diffusion characteristics at 500° C. For the Al+ implantation, the profile as-implanted is much broader than predicted and exhibits substantial enhanced diffusion at temperatures up to 500° C.

Jan 1, 1979

By F. M. Boler

The U.S. Bureau of Mines has configured a flexible data acquisition and analysis workstation, which incorporates control and analysis software written in-house for use in mining research experiments conducted in the laboratory and in operating underground mines. This data acquisition system combines computer-automated-measurement-and-control (CAMAC) modular instrumentation with a Unix-based graphics workstation. The data acquisition front-end hardware can be interfaced to almost any computer. CAMAC instrumentation modules adhere to mechanical, electrical, and digital interface standards and can be custom designed or purchased off the shelf. Communications along the CAMAC bus are regulated by the crate-controller module, which contains the only hardware link to the computer interface. Software support for the data acquisition and analysis workstation consists of a series of functions and programs written in the "C" programming language designed to provide flexible and fast data acquisition, processing, and analysis. The user can interactively control the digitizers and other CAMAC modules by sending standard CAMAC read, write, and command function codes from a menu-driven program. Automated data collection is achieved through software that responds to hardware interrupts triggered by acoustic emission or microseismic events. Graphics display routines are used to plot part or all of the data and provide the ability to process and store signal information selectively.

Jan 1, 1990

By Robert E. Meredith, Thomas T. Campbell

An investigation was undertaken to examine the feasibility of employing low- temperature nonaqueous baths for electrodepositing some of the refractory metals of the ferroalloy group . To date , such metals as tungsten , molybdenum , and vanadium have been produced only by high - temperature processes that are technically difficult and sometimes cumbersome in operation . Deposition studies were performed in a wide variety of organic solvents , including amides , ammonia derivatives , ketones , polyhydroxy alcohols , and ethers . Compounds prepared and used as solutes included the chloride and bromide salts of vanadium , tungsten , and molybdenum . Studies were conducted over a temperature range of 20 ° to 200 ° C under inert atmosphere . Conductivity and current potential data were obtained for all baths that contained reasonable solute concentrations . Qualitative solubility data were obtained for compounds of ferroalloy metals in a variety of solvents . In general , all solutes showed low solubility in ethers and ketones but reasonable solubility ( in excess of 20 grams per liter ) in alcohols , amides , and ammonia derivatives . No successful metallic deposits that would encourage further study were obtained with any of the systems that were examined .

Jan 1, 1963

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010

By R. Hogg, Y. Lee, D. E. Rannels

"Lee, Yu-Chen, Richard Hogg, and D. Eugene Rannels. Extracellular matrix synthesis by coal dust-exposed type II epithelial cells. Am. J. Physiol. 267 (Lung Cell. Mol. Physiol. 11): L365–L374, 1994.—Although integrity of the alveolar basement membrane may influence progression of lung injury induced by inhaled particulates, little is known about direct effects of coal dusts on the alveolar epithelium or its extracellu¬lar matrix (ECM). Effects of dust on synthesis of cell and ECM proteins by type II cells (T2P) was thus investigated. Three coal dusts (anthracite no. 867; bituminous no. 1451 and no. 1361) and mine dust MIT-3, of respirable size, were studied as a function of dose and time over 3 days of primary T2P culture. On day 1, 750 µg/ml of 867 were required to increase relative synthesis of ECM proteins (ECM/cell). MIT-3, 1451, and 1361 were without effect. By day 3, 867 or MIT-3 increased ECM/ cell 60-100% at 300 µg/ml; 1451 produced modest, dose-dependent stimulation, whereas 1361 remained without effect. None of the dusts caused significant cytotoxicity. The results show dose- and time-dependent effects of well-characterized coal and mine dusts to modify partitioning of newly synthesized proteins into the ECM and suggest that coal dust exposure may modulate structure or function of the subepithelial basement membrane.basement membrane; cell culture; inorganic dust; lung injury; extracellular matrix deposition; pulmonary epitheliumCHRONIC EXPOSURE to coal dust may be associated with development of pulmonary fibrosis and consequent loss of normal lung function (see Ref. 26 for review). Al¬though the pathways of inorganic dust-induced lung injury are recognized to involve an inflammatory re¬sponse, the underlying pathogenic mechanisms are not understood in detail. Acute and chronic responses to dust exposure involve a variety of interacting cells of the immune system, including macrophages, T cells, and B cells, along with pulmonary fibroblasts. These responses reflect direct effects of the dust particles, as well as indirect effects mediated by soluble factors, including cytokines and eicosanoids (see Ref. 41 for review).Studies of pulmonary macrophages and fibroblasts following silica exposure suggest that dust-induced damage at the airway surface may involve cellular injury through oxidant-mediated pathways. Coal dusts and related inorganic particulates can activate the alveolar macrophage (42) to produce fibronectin (15) and cytokines, such as interleukin-1 or tumor necrosis factor (4) and/or other soluble products which act locally (29) to cause acute cellular injury and to initiate the progression of fibrotic lung damage (16). Type I epithelial cells are typically more susceptible than type II cells to oxidant injury. Type I cell damage and subsequent death leads to denudation of the subepithelial basement membrane (2, 21) and can be associated with leakage of plasma constituents from the pulmonary vasculature into the alveolar compartment (13)."

Dec 1, 1995

By Richard J. Leary

The inputs of capital and labor to support future iron ore production were developed by the Bureau of Mines from projections of iron demand and estimates of capital and labor requirements. Trends in technologic change and the organization of production were analyzed. Labor requirement schedules for iron ore mining and beneficiating were constructed from aggregate inter-temporal trends and 1970 cross-sectional analysis of mines and mills. A sup-ply schedule of the capital requirement for mine-mill-pellet plants was developed from U.S. and Canadian experience. The structure of demand for iron to the year 2000 was examined as well as the availability of resources. Projections of capital and labor requirements to 2000 were constructed under two international patterns of iron ore supply to the United States. The most likely model is for a continuation of the 70 percent United States-30 percent foreign shares, expanding at an average 2.0 percent growth rate to 2000, and supported by a cumulative gross capital investment of $3.8 billion constant 1967 dollars and a labor force in the United States of 29,800 by 2000. The information content of projections is discussed, and the possible effects of international forces on supply are considered. A generalized methodology for estimating capital and labor requirements in other mineral industries also is included.

Jan 1, 1975

By William W. Elmer

This paper, describing the mining method at the Black Butte quicksilver mine, is one of a series of papers being prepared by the U. S. Bureau of Mines on mining practices, methods, and costs in the various districts of the United States. It is presented to show the mining practice and costs in the successful treatment of low-grade quicksilver deposits. The operation discussed is an excellent example of w1-pat can be done in working a limited tonnage of low-grade ore under sound management. The Black Butte mine is situated at Black Butte, Lane County, in the southern part of the State of Oregon, 17-1/2 miles from Cottage Grove -- a station on the Siskiyou branch of the Southern Pacific Co. The Black Butte mining district lies in the foothills of the Calapooia Mountain Range, which connects with the Cascade Range on the east and with the Coast Range on the west. The elevation at '.lie reduction plant is 1,000 feet above sea level. The apex of Black Butte Mountain, or which the mine is situated, has an elevation of 2,700 feet. The district possesses exceptional natural facilities infrequently met with elsewhere for the mining and reduction of cinnabar ores. Several factors which contribute to the unusually low mining costs are:

Jan 1, 1930

By Industrial Research Office

"The U.S. Bureau of Mines established on August 15, 1983, the Generic Mineral Technology Center for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. The Center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to ""... permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . ."" The Center's program is designed to permit an accelerated attack on the fundamental research problems for the control of respirable dust in mines.The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. The Generic Technology Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated. The Center activities involve the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications' in the respirable dust area.The Center is composed of faculty from the four universities/institutes listed above. The personnel, facilities and equipment that are available to the Center from these entities are diverse, complementary and comprehensive. More than fifty scientists, engineers; and medical personnel in the Center are engaged in respirable dust research. Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease Studies are available as a result of the existing relationship between NIOSH and West Virginia University.The breakdown of the dust research program into the five areas mentioned above recognizes the importance of an integrated fundamental research approach to the respirable dust problem compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities. The specific projects in the research areas are a result of a careful evaluation of the past and ongoing research activities, the identification of areas where data and information are scarce, and awareness of the recommendation of the National Academy of Sciences Study on the Measurement and Control of Respirable Dust. Penn State is the administrative unit for the Center. Funding to date is nearly $6.5 million."

Aug 31, 1989

By K. A. Fowler, L. W. Higley

Steels with an alloying addition of depleted uranium were studied to develop successful melting , casting , and fabricating methods ; to obtain data on mechanical properties ; and to determine the effects of this alloying element . Uranium in amounts up to 1.5 percent was added to steel - base compositions containing approximately 0.5 percent carbon , 2 percent nickel , 0.25 to 2.0 percent silicon , and 0.75 percent manganese in both vacuum- melted and air -melted heats . Radiation levels were monitored for all operations . Bureau of Mines research at the Rolla Metallurgy Research Center showed that uranium additions did not increase tensile strength ; that hot - shortness occurred during forging above 1,090 ° C because of the presence of a low melting point constituent of a eutectic type ; and although a measurable amount of radioactive contamination resulted from processing , the quantity was never large enough to require the work area to be identified as a radiation area .

Jan 1, 1964

By E. W. Parsons

Permanent support of the back is an important economic factor in maintaining a tunnel or other underground opening in condition to render the service for which it was driven. Timber has been most commonly used for support in tunneling and drifting because of its strength and ease of installation. Even when treated for decay, however, timber is subject to deterioration and, over a long period of time, should not be considered a permanent support. Concrete support or lining is permanent and has been used in tunnels of every size for many years but has been almost exclusively cast in place, a difficult, costly process. This report deals with the design and installation of precast concrete supports to combine the best features of both methods.

Jan 1, 1958

By Rolland L. Blake

Petrographic methods of examination were used by the Bureau of Mines on a suite of samples of ultramafic rock from Soapstone Ridge, Ga., located about 8 miles south-southeast of Atlanta. The samples were analyzed to determine (1) their potential for releasing regulatory particles upon crushing and grinding and (2) their concentration of fibrous particles that approach the dimensions of amphibole and serpentine asbestos minerals. Such particles might be generated during grading and excavation for housing and industrial development and could become a health concern. Light optical microscopy, scanning electron microscopy, and X-ray diffraction were the techniques used to examine the samples. Six of the twelve samples contained amphibole as a major mineral; in five, it was a moderate to minor mineral. One sample contained no amphiboles, and serpentine was not observed or identified by X-ray diffraction in any of the samples. In nine of the samples, the amphiboles exhibited a habit that was either prismatic or acicular, but not asbestiform. Two of the samples did contain asbestos, occurring as small veins or fracture fillings, which represented only a minor percentage of the total sample. Similar petrographic screening is recommended for examining any rock deposit or mine location to delineate hazardous and nonhazardous mineral areas.

Jan 1, 1982