Search Documents

By Warren E. Morrison

Demand for energy in the United States in 1965 was stimulated by the continuing expansion of the economy. A gain of 5.9 percent in gross national product for the year was accompanied by a 4.4-percent rise in energy consumption. Domestic energy resources met about 93 percent of the nation's requirements. The remaining 7 percent consisted of imported fuels, mainly of crude petroleum and residual fuel oil. The major fossil fuels-natural gas, crude petroleum, and coal, in that order-contributed 96 percent of all commerical energy utilized, with the balance of 4 percent being primary electricity from hydropower and nuclear power plants. Production was up for all of the major mineral energy resources in 1965, with the single exception of anthracite, output of which continued to decline. Bituminous coal output for the year was 512 million tons; marketed production of natural gas, 16,039 billion cubic feet; and crude petroleum output, 2,848 million barrels. Among the secondary products processed from primary energy resources, the most significant gains were in coal carbonized for coke which increased 6.7 percent to 95 million tons, and in the output of liquefied gases from natural gas which rose 4.8 percent to 11,257 million gallons (268 million barrels). Within the latter category, the off? take for petrochemical feedstocks continued to rise at a very rapid pace.

Jan 1, 1967

1. In 2002, a total of 4,311 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). The major industrial classifications in stone mining are dimension stone (used for construction purposes), crushed and broken stone (aggregates), cement, and lime. Stone mines comprised 29.7% of all mining operations. • Mines producing crushed and broken stone (n = 3,372) comprised 78.2% of all stone mining operations.

Jan 1, 2004

In 2001, a total of 2,144 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 14.7% of all mining operations. • Bituminous mines comprised 92.0% (n=1,972) and anthracite mines 8.0% (n=172) of coal mining operations. • More than 71% of coal mines were located in three states: Kentucky (29.5%), West Virginia (21.3%), and Pennsylvania (20.6%).

Apr 1, 2003

By George H. Schnakenberg

Automation of coal mining activities at the face offers improvements in worker safety, health, and productivity. Introduction of integrated computer-sensor systems to current mining machines will enable these machines to perform some of the most hazardous tasks through supervised teleoperation. The U.S. Bureau of Mines is pursuing the development of the enabling technology necessary to achieve this goal. The research program consists of both basic and applied research, each focused on the fundamental issues of computer and sensor technologies. Short-term research is directed to providing computer-assisted, remote supervisory operation of present underground equipment; the long-term goal is the development of progressively more intelligent mining systems. The research program includes a review of robotic machine and autonomous vehicle technologies and of current mining technology, which provides a base for developing innovative mining methods; research in navigation and guidance technology, emphasizing control of a continuous mining machine; research on coal-rock interface sensing technology for horizon control, and rib thickness control in highwall mining; the development of computer systems and hierarchical architectures for real-time control; and development of expert systems for machine system fault diagnostics and predictive maintenance. This report presents a brief background and the current status for each of these research areas.

Jan 1, 1989

By Liming Yuan, Charles D. Litton

This paper presents experimental results for conveyor belt flame spread from tests conducted in a small-scale tunnel. The purpose of this study is to investigate the effects of belt type, ventilation velocity, belt surface-to-roof distance and ignition source power on the flame spread properties. The tunnel used was 4.9 m long by 0.46 m square with the ventilation velocity ranging from 0.7 to 3.2 m/s. The ignition source was an impinged methane jet burner with heat output ranging from 7 to 21 kW. The belts tested included non-fire resistant rubber belts, fire-resistant rubber belts, fire-resistant neoprene belt and fire-resistant PVC belt with belt samples measuring 0.23 m wide by 2.5 m long. Experimental results show that with a ventilation velocity of 1.02 m/s all conveyor belts could be ignited, and that with sufficient ignition source power, flames spread the full length of the belt sample. The data showed a coupling effect of the ventilation air velocity and the belt surface-to-roof distance on the flame spread rate. For instance, flames could not spread with a ventilation velocity higher than 1.52 m/s and a surface-to-roof distance of 0.22 m. The use of the measured CO/CO2 ratio as an indicator of combustion stoichiometry is also discussed.

[ ]

Jan 1, 2012

By E. C. Perkins

Preliminary experiments are reported utilizing bacteria to leach manganese from a variety of domestic low grade manganiferous materials. In two large leaches manganese extraction ranged from 71.7 to 92.5 percent, and the products analyzed over 48 percent manganese. Nutrient requirements and leaching time experiments were made. The mechanism of leaching is not understood, but is different than the mechanism encountered in the microorganism accelerated leaching of copper in the presence of sulfide minerals.

Jan 1, 1962

By John B. Umhau

[This !m-i~!.al survey giver, statistice.1 data res;?~dirf ~:rimay ard ?eco~- dqr or scmn tin used in thL: United St,ztas by industries an? incluclcz d;ta on stop&apos;ics, ~urchares, ard plnrt losr.c.5. It is :i ml:anwe of consq~tion in terms of fir.is1icd -prcd.~cts nz6.e iry initid ti11 Sabric:,.torc,, that is, aon- cerns that purchzse virc,in zni s~col~d&apos;l~y i.i.5 ti:; 01&apos; tin c;cra.. rav materi,als ar,d co:lrrert them into !ror?ucts such F!: ti:i plz.te, ~lloyr;, and. c?hemic?ls; comy~nias ;~urchn.&apos;.ii~; alloys, ch:rr.ic,~l::, or tin vl?.tc fcr furthcr a:mflzc- ture ?rc: ~-.f>t i~ci~~dcd. Tilit r~lqe:;tionrr::ire submit tod to consunern ar,nt:incd no dofinition of rnr.oncl.:ryr me$.-i; but, ovrirq to ti~i-: a~counti~ procedure used s.l~o~c-:t 1&apos; thu scrnn hac i~-.rtergol:e ch?rri?~ of ovinerzhip or titlo, thc rc!coverod t! n !its b~en i-c<;,r(it.!rj L.S r,e~3r;d:q met.1. Tbv tin content ~f ]

Jan 1, 1938

By Donald F. Reed

In its investigation of old, abandoned, lead-zinc mines at which records of operations are not available, in 1914 the Bureau of Mines dug surface trenches anti&apos;, in 1947 It diamond-drilled three holes at the Albright Farm deposit in Sinking Valley. Some good lead-zinc ore had been extracted from veins in dolomitic limestone during the time of the American Revolution and as late as 1870. Since that time the only activity was sporadic prospecting and developing. Thu Bureau of Mines disclosed two additional veins by surface trenching, but diamond drilling failed to find significant lead-zinc mineralization.

Jan 1, 1949

By Jack E. Fraley

Magnesium oxysulfate cement has been specially formulated as a sealant in underground coal mines for reducing sloughing of shale roofs and coal ribs, for reducing air losses through block stoppings, for constructing sprayed stop-pings over approved jute cloth or metal lath, and for reducing combustibility of polyurethane foam. A standard spray machine (Mining Enforcement and Safety Administration (MESA) approved) was used for the underground testing. Our research shows that a 1/2-inch coating reduces shale and coal sloughing, reduces air losses through block stoppings, and prevents fire propagation through a metal tunnel lined with polyurethane foam. During the underground tests, excess mixing water was used to improve pumping the slurry to the spray nozzle. This was later found to increase shrinkage cracks in the cured coatings. Controlling excess water is important to an acceptable coating.

Jan 1, 1976

By M. V. Potter

"In nearly all fields of investigation, research laboratories and routine testing laboratories encounter problems in which the primary determinations involved in the study require the measurement of mechanical vibrations or motions. These vibrations,may be of an oscillatory nature covering frequencies from a few cycles per second up to hundreds of Kilocycles per second, or they may be more or less uniform study nations occurring at rather slow rates. In electrical, or mechanical methods. In the optical case the to cause the deflection of a light beam such that the motion of the mechanican system of the beam can be determined, then by direct the by direct observation on a suitable scale or by recording it’s the electrical methods the motions can be made to changes in resistance, capacity or inductance proportion to the mechanical displacement or electromagnetic means can used to generate directly a voltage that will be porpertuial to the instantaneous vicinity of the vibrations. Other devices are used in a special instance, also but in any cause the electrical methods produce a current that is an electrical counterpart of the mechanical motion, and the motion can then be studied by direct measurements of the current or by recording the current on suitable recording meters or oscillography. Mechanical methods are used in some instance but are generally not as convenient nor as flexible as the optical and electrical methods."

Feb 1, 1943

By Joan C. Biordi

[Composition profiles for atomic, radical, and stable species, as well as temperature and area expansion ratio profiles, have been determined for a nearly stoichiometric CH4-02-Ar flame and one to which 0.3 percent CF5Br inhibitor had been added. Net reaction rate profiles were calculated for all the observed species. For the normal flame, these and the mole fraction profiles gave rate coefficient information about the elementary reactions in the methane flame, for example, CH. + 0 4- H2CO 0 H, k4 = 1.05 X 1014CM3 mole-1sec-1 for 1,550§T 0,725&apos; K; CO + OH 4 C02 + H, k6= 4.7 X 1011 for 1,350{T X1,750° K. Comparison between the inhibited and normal flame showed that A] and [CH3] were significantly reduced at the lower temperatures in the inhibited flame even though in the hot gas region the [E] [OH!, and [0] were essentially the same in both flames. The CF3Br disappears very early in the flame, relative to the fuel, and the reaction primarily responsible for its disappearance is H v CF3Br 4 HBr + CF3, where k7 is found to be 2.2 X 1014 exp(-9460/RT) for 700-1,550° K. Reaction of the inhibitor with methyl radicals provides for the relatively small amounts of CH3Br observed, but CH3 + Br2 - CHs Br + Br must also occur. The HBr formed reacts rapidly with H atoms to form H2 and Br, but the reaction is soon "balanced" in the flame as may be demonstrated by calculation of the equilibrium constant at various temperatures. The fluoro-carbon fragment produced in reaction (7) also reacts rapidly, in part with methyl radicals to give the observed elimination product CH2CF2 Later in the flame, above -1,400&apos; K, F2CO is formed from the reaction CH2CF2 + 0 P F2CO + CH2 and k., -1.5 X 1013 at 1,600° K. The rather slow decay of carbonyl fluoride is attributed to reaction with H atoms according to the sequence F2CO I H - HF + FCO and FCO + H HF + CO.]

Jan 1, 1975

By Lloyd A. Morley

Two methods are presented to determine the mechanical shaft torque as a function of time for an induction motor. The methods are based on the motor equivalent circuit and use as input variables of the motor terminal voltage, line current, input power, and power factor. One method uses all four variables and the other uses only voltage and current. The test data deals specifically with continuous miners, but the theory could be applied to other mining machines driven by multiple induction motors. Results are given for the tramming, maneuvering, cutting, and cutting with loading operations and are in the form of a minimum, a maximum, and an average of the shaft-torque time function. The theoretical development and computer implementation are discussed for both methods.

Jan 1, 1978

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

By Charles L. Kimbell

Available statistics on 1991 worldwide consumption of selected non fuel mineral commodities shown in table 12 indicate downturns for all but 3 of the 15 listed commodities. It should be stressed that in most instances, the consumption declines were primarily the result of lower levels of use in the former U.S.S.R. and the former centrally planned economy nations of Eastern Europe. However, several commodities suffered use cutbacks in market economy countries. In the case of the nonferrous metals covered In the table, the differences in performance between market economy countries and the former centrally planned economy states are immediately evident from the table itself. Among these important commodities, refined lead, primary magnesium, and refined tin registered downturns for market economy countries as well as among the centrally planned economy countries. Also notably, cadmium use showed no significant change from 1990 levels in either group of countries. Global consumption of iron ore fell by 3.4 % or about 31 million tons, and this was a greater decline than that logged for production of marketable iron ore and related products, which was down by only 3.0% or almost 28.2 million tons. Thus, it would seem that for another year there was a net addition to stocks. The 1991 drop in iron and steel scrap use was about 5.5 % or about 18 million tons, on the percentage basis somewhat greater than the 4.8% or 36.9 million ton drop in global steel production. Although consumption of iron ore and iron and steel scrap are not broken down by region in table 12, it seems almost assured that the pattern of 1990 continued into 1991: drops in use in the former U.S.S.R. and Eastern Europe were the overwhelmingly dominant declines and accounted for much, although not all, of the global decline, whereas among market economy countries as a group, there were upturns for both materials. On a global basis, it would appear that the slight shift in the ratio of pig iron to scrap in steel furnace charges noted in 1990 continued into 1991, this shift being toward a slightly larger proportion of pig iron with a corresponding decline in the share accounted for by scrap.

Jan 1, 1993

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

By W. M. Myers

The U. S. Bureau of Mines conducted an investigation to determine the cause of the deterioration of Portland cement during storage and transportation , and to discover a means of preventing it . All available printed sources of information on this subject have been examined and a bibliography has been compiled . The subject has also been discussed with the leaders in the cement industry ; the present report is the result of their cooperation , and is based principally on information thus obtained . Deterioration of Portland cement during storage over any considerable period of time has long been noted ; closely related to it is deterioration of cement during transportation, which involves not only the time factor of storage but also exposure to varied climatic conditions . Deterioration in both cases is due to hydration of the cement by absorption of moisture from a humid atmosphere , or by exposure to actual rain-fall . After hydration cement possesses no cohesive power ; the degree of deterioration is directly proportional to the degree of hydration . The amount of deterioration of Portland cement during storage has been accurately determined in an investigation by the Structural Materials Research Laboratory , in cooperation with the Portland Cement Association . Cement stored in a shed in cloth sacks retained 80 per cent of its original strength after three months storage ; 71 per cent after six months ; 61 per cent after one year ; and 40 per cent after two years . The deterioration of Portland cement during storage and transportation was noted particularly in France during the World War . Information concerning cement used by the American Expeditionary Forces was furnished by Lt. Col. H. S. Spackman and Major E. C. Eckel , U. S. R. , who had charge of practically all matters concerning cement used by the A. E. F. The cement used by the A. E. F. came from the following sources : 42,000 tons was French , Swiss , and Spanish cements ; 120,000 tons was English cement ; 55,000 tons made in plants operated by the A.E.F .; 500 tons ( Not over) from America . Deterioration was most marked in cement from the first source .

Jun 1, 1922

"A coordinated, integrated research effort aimed at studying the scientific, engineering and medical aspects of the respirable dust problem is underway in the areas of dust generation, dust dispersion and dilution, dust characterization, interaction of dust and lungs, and relationship of seam characteristics to dust generation and mobility. (FIGURE 24) The Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the dust-lung interaction processes that lead to mine worker disability. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated.Research projects in the Generic Mineral Technology Center for Respirable Dust have effected several improved methods for the preparation and characterization of the dusts needed by these projects. Superior procedures for generating ""standard"" dust samples have been developed and are in regular use in the laboratory. Questions raised during the course of some projects regarding ""stale"" versus ""fresh"" dust have led to the development of sampling techniques where the dust is directly collected in a surfactant. MSHA and CANMET have requested and received information on Center generated software. An equipment manufacturer, TSI, Inc., requesting input on modifying the inlet of an aerosol sampler has been assisted as a result of research that was conducted at the University of Minnesota.The objectives, scope and progress of all the research projects in the Center, in the form of abstracts and reports, have been detailed in Volume 1 of this series. Research papers written by the principle investigators and resulting from the findings of projects (FIGURE 25) and which are funded by U.S. Bureau of Mines grant number G1135142 have been published in Volumes 3 through 6 and Volume 8 of this series. Volume 2 relates the cooperation and interaction of the U.S. Bureau of Mines and the Generic Mineral Technology Center for Respirable Dust in research on the problem of respirable dust in the mineral industries."

Aug 31, 1989

By E. B. Swanson

Atlantic seaboard refining and marketing companies , dependent largely upon other producing and refining areas for the crude and refined petroleum needed to meet the demand for petroleum products within the Atlantic Coast States , reported an increase in 1929 receipts of 2,542,000 barrels of crude petroleum and 13,479,000 barrels of gasoline over the quantities received during the preceding year . The relatively large expansion in gasoline receipts undoubtedly resulted from the unexpected increase in gasoline consumption which characterized the petroleum industry during 1929. Gasoline receipts from California increased 6,354,000 barrels and shipments from foreign countries were 5,381,000 barrels in excess of the 1928 figures , while receipts from Gulf Coast ports , the major source of outside supply, declined 811,000 barrels . Shipments of domestic crude oil by tanker from Gulf Coast ports during 1929 continued the average annual increase of approximately 7,000,000 barrels which has been recorded during the five years of this annual survey . These shipments have increased from 72,556,000 barrels during 1925 to 99,828,000 barrels during 1929. Shioments of Mid- Continent crude by pipe- line to Atlantic Coast refineries have , on the other hand , dropped from 11,903,000 barrels in 1925 to 1,409,000 barrels during 1929. Receipts of foreign crude oil declined 1,461,000 barrels from the preceding year . : Gasoline demand within the Atlantic Coast area reached a total of 123,345,000 barrels , an increase of 15.7 per cent over 1928. Gasoline production increased 4,157,000 barrels , while tanker receipts were nearly 11,000,000 barrels larger than in 1928. Indicated shioments from Appalachian refineries were somewhat larger than in the preceding year . Gasoline production showed an average of 33.5 per cent of the crude throughout , as compared with 31.5 per cent in 1928 and 32.7 per cent in 1927. Cracking operations accounted for 44.6 per cent of the gasoline produced , as compared with 40.6 per cent in 1928 and 35.3 per cent in 1927. Gas oil and fuel oil production averaged 52.8 per cent of the crude throughput , as compared with 55.1 per cent in 1928 and 49.5 per cent in 1927 , the decline reflecting the smaller quantities of foreign crude refined during the year .

Nov 1, 1930

By Raymond B. Ladoo

"The increasing realization of the fire hazards involved in the use of wooden shingles caused the National Lumber Manufacturers' Association to beginsome five years ago a search for a suitable fire-resistant paint. The problem was submitted to the Educational Bureau of the Paint Manufacturers' Association of the United States and work was started by Mr. Henry L. Gardner at the Institute of Industrial Research, Washington D.C. in collaboration with Dr. Herman von Schrenk, a timber expert of St. Louis.The results of this,work have been described by Heckel, in ""Asbestos"", (Heckel G.B., Asbestos in the Paint Industry, Asbestos, Vol. 2, July, 1920,pp.- 5-10).,,who gives the following formula for one of the colors as typical: It will be noted from this formula that ""asbestine"" forms 33% of the total liquid pigment by weight or 31.8% of the solid constituents. Hockel in the article referred to describes this paint,as ""asbestiform"" and assumes since ""asbestine"" is magnesium silicate it must be the chrysetile variety of ""Asbestine"", however, is not asbestos but is a trade name for a fibrous variety of talc mined in the Gouverneur district, St. Lawrence County, New York. This rather natural error persists through the article and credits asbestos with many desirable properties which are characteristics of talc."

Aug 1, 1920