Search Documents

By Farrel W. Lytle

An X-ray emission spectrographic method of analysis is presented for determining rare-earth elements in fractions obtained from bastnaesite ore. The method includes determination of yttrium, thorium, lanthanum, and the rare-earth elements in various complex mixtures. The analysis technique is based upon comparing the samples with synthetic standards approximating the composition of the samples. Working curves are plotted on an absolute-intensity basis, with no correction for back-ground. Examples of working curves and the analyses of typical rare-earth concentrates are included. The selection of spectral lines for the various sample matrices is discussed. A special technique is used for samples in which rapid hydration and carbonation occurred. By analyzing synthetic samples of known composition, the accuracy of the method was determined. The average error of analysis was about 3 percent of the amount present in the range from 5 to 100 percent and about 7 percent in the 0.2-to 5-percent range. A maximum of about 40 samples per day may be analyzed for 7 elements each.

Jan 1, 1957

[ ]

Jan 1, 2012

By NIOSH Publications

In 2004, 14,478 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (48.9%) were sand and gravel mines, followed by stone mines (30.4%), coal mines (13.9%), nonmetal mines (5.1%), and metal mines (1.7%).

Sep 1, 2007

By Thomas J. Peters

The U.S. Bureau of Mines studied the 63,9SS-acre Hanson Lakes study area, including the Ten Mile-East and part of the Ten-Mile West RARE II areas, plus additional acreage, all proposed at times for Wilderness designation. The study was part of a Idaho Land Assessment Program with the Idaho Geological Survey and the U.S. Geological Survey, to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The area is at the north end of the rugged Sawtooth Range and includes parts of the Sawtooth National Recreation Area which is closed to mineral location. The Copper Mountain. Elk Mountain, and Observation Peak mineralized areas are in the study area, but only Copper Mountain is open to claim location. It is on the trans-Challis fault zone and contains Tertiary granite which is favorable for mineral deposits of gold, beryllium, niobium, REE (rare-earth elements), tin, molybdenum, copper, silver, and lead. Identified resources are 1.9 million tons of flake graphite at Elk Mountain, but much more graphite occurs in the vicinity REE occurs in 18 black sand placer sites along the lower reaches of study area streams just outside the study area, on Cape Horn Creek, Marsh Creek, and lower Valley Creek flood plains, and at one hydrothermal site near Observation Peak. Hydrothermal REE is commonly low in? by-product thorium. a radioactive disposal problem. Many advanced REE applications enhance the quality of life, and future uses in superconductivity may reduce energy consumption. Seventeen lode, one geothermal, and 11 placer prospects were examined. Workings totaled about 20 adits, one shaft, several open cuts, and numerous small pits. Approximately 500 mining claims have been located or relocated in the study area, including a 200-claim block for disseminated molybdenum.

Jan 1, 1992

By S. R. B. Cooke, J. Bruce Clemmer, Will H. Cognill, F. D. DeVaney

"INTRODUCTION The domestic production of potash has made rapid strides in the past 4 years. In 1929 the United States produced 109,820 tons of potash-bearing material, equivalent to 61,590 tons of pure potash (K20). In 1933 to this had increased to 331,110 tons, containing 143,378 tons of potash, due chiefly to the development of the potash deposits near Carlsbad, N. Mex. The potash ores of that district occur at a depth of about 1,000 feet and as mined consist of a mixture known as sylvinite containing about 40 parts of sylvite (KC1) and 60 parts of halite (NaCl). By careful mining the extraneous material does not amount to more than 2 or 3 per cent. Such ore was used in the experimental work here reported.The usual chemical method for the recovery of potash from sylvinite, while efficient in the production of pure potassium chloride, requires,expensive equipment and is costly to operate. It occurred to the Bureau of Mines that ore-dressing methods, which have been applied to other nonmetallic minerals, might be adapted for the production of a grade of potash suitable for the fertilizer industry. After preliminary study by the Bureau of Mines showed that ore-dressing treatment was possible the investigation was extended under a cooperative agreement between the U.S. Bureau of Mines, the Potash Company of America, and the Missouri School of Mines and Metallurgy, Rolla, Mo.ACKNOWLEDGMENTSAcknowledgment is here given for valuable assistance in the laboratory of R. G. O'Meara, assistant metallurgist. U.S. Bureau of Mines, Tuscaloosa, Ala. who was on detail at the Rolla station during the early work; by E. W. Gieseke and Albert Ollar, temporarily employed by the Potash Company of America; and to N. H. Lenz, an engineer temporarily assigned to the station."

Feb 1, 1935

By Samuel W. McNary

In August 1984 the U.S. Bureau of Mines conducted a study of the mineral resource development potential of the Badger Canyon-Antelope Creek area, within the Boulder-Pioneer wilderness study area, about 5 miles northeast of Ketchum, 10. The purpose of this study was to investigate in greater detail an area which was designated by the U.S. Geological Survey (USGS) and the Bureau as having a moderate mineral resource potential for zinc, molybdenum, lead, and silver, and a low potential for copper. One hundred twenty-eight soil samples were taken along a 6,2S0-ft traverse on the ridge separating Badger Canyon and Antelope Creek. 5 Five rock samples were collected from old prospect pits and mineralized outcrops. All samples were analyzed for gold. Silver, copper, lead, zinc, molybdenum, arsenic, antimony, vanadium, and mercury. The metal concentrations in the soil samples along the traverse are irregularly distributed. Samples collected near old prospect pits tend to be high in lead and zinc, undoubtedly a reflection of underlying galena-and sphalerite-bearing quartz veins. All of the copper and mercury values in the soils are less than the detection limit, as are most of the lead, molybdenum, and antimony values. Except for lead and zinc values, the metal concentrations in the rock samples are low. Galena and sphalerite were observed in quartz vein samples collected at the old prospects. The results of the study indicate that the galena-sphalerite-bearing quartz veins and veinlets are too narrow, widely-spaced, and low in metal values to be economic. Low concentrations of metals in the soil and rock samples, combined with the lack of major mining activity in the past, indicate that the area has a low likelihood for economic development.

Jan 1, 1986

To develop a quick, safe, and effective method that allows workers at mineral processing operations to clean their dust-soiled clothing periodically throughout the workday. Background Reducing workers' respirable dust exposure to silica and other harmful dusts and contaminants is an ongoing goal in the U.S. mining industry. One area of known worker exposure is from contaminated work clothes. A U.S. Bureau of Mines report documented a number of cases where a tenfold increase in a worker's dust exposure was measured from contaminated work clothes. In these cases, the dust emitted from clothing caused the worker's dust exposure to exceed the permissible exposure limit in less than 2 hours. The most effective way to eliminate this dust source is to have workers clean or change their work clothes. There are two federal regulations that impact the clothes-cleaning process. The first states that at no time shall compressed air be directed toward a person, but that when compressed air is used, then all necessary precautions shall be taken to protect persons from injury. The second regulation states that compressed air should only be used for cleaning purposes when it is less than 30 psi and used along with personal protective equipment. For the mining industry, by default, the only approved method to perform clothes cleaning is to have workers vacuum their clothes using a HEPA filter system. This is very difficult and time-consuming and, in most instances, not very effective. Most workers would prefer to use a single compressed air hose to blow dust from their work clothes. However, not only is this method prohibited by law, it usually creates a significant dust cloud in the work environment and contaminates coworkers.

May 1, 2005

By J. B. Janus

This report, the 22d in a series, gives analytical data showing composition and quality of tipple and delivered samples of coal collected during fiscal year 1972. This coverage lists mines located in 20 States. Ultimate analyses are given for most of the coalbeds listed. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. The deliveries were sampled in accordance with instructions issued by the Bureau of Mines, and the samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By John Gross

In connection with some investigations being made at '!'he Ra.re uid Precious 1ets.ls Station of the U, S. Bu.rea.u of Mines, at Reno, Nev., on the precipitation of gol'i and silver from cyanide solutions, it wa.s sug­ gested tnat the use of acetylene for this purpose be investigated, A pa.tent was iss·.ied to Fre<!.erick W. Martin and Frederick Stl1.bbs in 1900 covering the precipitation of precious metals from cyanide solu­tions by acetylene, The acetylene used in the tests described below wa3 made f'rom a. corr.:nercial cal ci \'!Z:l carbid.e, A r..umber of exper:me11. +,s rezul ted in more or lP.ss ccmplete pree;p1tatien of silver, -but 1n no case was a11Y gold precipitated. As silver acetylide, obtained by precipitatir.g the silver from an ar:::ncni'i\.Ca.l so1ut1on of silver n,. tra.te by acetylene, is yellowish white, esn:, solu'.)le in cyanide and hlghly explosive, and the pr9cip1tate ob­tain£ frcvm the cy'31lide sclutions was black, not tlubla L., cyanide and not explooive, it 'Na.s deid-,d. to ir.·.restigate the na.tur.e of the slJ.ver pre­cipit.te !rem the cy;r:iide solu·t:i.i,ns, !n prepa;.•i::lg a lge (!\,wrttity ,:f the preci-pi tte 1 t. wa, fo·und that a.fter c,:.\i;:1 ete prEc"'.pi tat ion cf the eil ver the !IOl ution con ta.ined soluble eulphic.e • Thia p:!:'O'lided a el f!W "lt·d. a.ft er apr,ropri-9.te tests the preeipita.te VIO,I proved to 'be ailver sulphide.

Apr 1, 1922

By Robert L. Chufo

The paper, "An Electromagnetic Roof and Rib Thickness Sensor" presented at The 12th WVU International Mining Electrotechnology Conference in 1992, presented the results of roof coal thickness measurements in underground mines and rib coal thickness measurements in highwall mines. The microwave sensor described uses a unique spatial modulation scheme created by antenna motion, along with frequency domain signal processing, to solve the problem of media, target, and antenna dispersion. This paper further describes the advantages of the unique frequency domain signal processing technology chosen by the U.S. Bureau of Mines in extending previously reported one-dimensional thickness measurement technology to the generation of a full three-dimensional underground image of the underground environment. The electromagnetic signature of a media, whether it is coal or other geological material, is its permeability and permittivity and the effect on the velocity and amplitude of an electromagnetic wave as it passes through. High-quality imaging cannot occur without the identification of, and correction for, the permittivity and permeability of each layer of a multilayer geological deposit. Clutter, or any signal that can interfere with target discrimination, usually comes from objects in the field of view for which there is no design control. These are nuisance targets with possibly very high contrasts compared to the real target. The only proven tool to reduce clutter is to increase spatial, spectral, and polarization diversity. This paper will describe some techniques being used by the U.S. Bureau of Mines to increase the information content of both single-dimensional and three-dimensional imaging systems through the identification of media distortion mechanisms made possible by the use of spatial/spectral sensor technology. These techniques will permit high quality imaging in an environment where the data is corrupted by dispersion and clutter.

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workman enter those places, but dine to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By Richard L. Unger

The U.S. Bureau of Mines has designed, fabricated, and tested a prototype track maintenance vehicle for underground coal mines. The vehicle uses a stiff rotating brush to clean the track so that a visual inspection is possible. It is also equipped to measure track gauge and cross-level. The objective of this report was to describe the track maintenance vehicle and detail the results of investigations into present underground track inspection procedures and cleaning technologies, which led to the development of the prototype. Recommendations are made concerning the integration of components of this prototype vehicle into current track cleaning and inspection systems used in underground mines.

Jan 1, 1984

By Robert R. Stein

Occupational noise caused by the rock drills used in mining was investigated by the U.S. Bureau of Mines. Using a large reverberation chamber and an automated drill test fixture (ADTF), the sound power levels of mining drills were measured to determine if there are types of drills that are advantageous from a noise production standpoint. Test results show that while there are not large variations among types of drills, there are still some choices that could produce a positive effect on overall noise exposure. It is also shown that lower noise exposures are possible using larger drills because of higher production rates and better operator positioning.

Jan 1, 2010

By J. E. Chilton, Jr. Dubaniewicz

Many mines rely on toxic gas sensors to help maintain a safe and healthy work environment. This report describes a prototype monitoring system developed by the U.S. Bureau of Mines (USBM) that uses light to power and communicate with several remote toxic gas sensors. The design is based on state-of-the-art optical-to-electrical power converters, solid-state diode lasers, and fiber optics. This design overcomes several problems associated with conventional wire-based systems by providing complete electrical isolation between the remote sensors and the central monitor. The prototype performed well during a 2-week field trial in the USBM Pittsburgh Research Center Safety Research Coal Mine.

Jan 1, 1995

By Douglas A. Crum

The Taylor&apos;s friction circle method for slope stability analysis can be extended to incorporate multiple circles defining the slip surface in a failure mechanism so that it is a workable method for bearing capacity calculations of foundations and rotational failures of retaining walls and similar structures. The U.S. Bureau of Mines has further extended the multiple-circle method to include friction in the material strength and to utilize computational schemes such that this method can be programmed with optimization capabilities rather than being used as a graphical or semigraphical method. Some examples are given that demonstrate ultimate bearing capacity calculations of embedded foundations with eccentric loads and nearby slopes.

Jan 1, 2010

By Philip W. Holland

This U.S. Bureau of Mines (USBM) report describes a chromatographic method that is used for rapid field determinations of carbon dioxide in natural gas streams at a USBM helium production facility. The method employs a commercially available portable gas chromatograph that is equipped with a 10-m fused-silica capillary column coated with a porous polymer. The instrument operating parameters permit determinations to be performed over a concentration range of 10 ppm to 10 pct with a frequency of 20 samples/h. The speed at which determinations can be performed is an important factor when evaluating efficiency or troubleshooting processes at the helium facility.

Jan 1, 1994

By Donald E. Graham

A mineral survey of a 12,350-acre portion of the 13,150-acre Juniper Creek Wilderness Study Area (WSA) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1984. The area is entirely underlain by thick flows of Banbury Basalt. Rhyolitic tuff of Little Jacks Creek is exposed in the walls of the Owyhee River canyon beneath the basalt. Minor units of lacustrine sediment occur between the volcanic layers. No mines or claims occur in the area, and no mineralized zones were found. The study area is covered by oil and gas leases or lease applications; there has been no known exploration.

Jan 1, 1985

By Spencee L. Willett

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a 51, 160-acre portion of the 107,920-acre Diablo Mountain Wilderness Study Area (OR-001-058) in order to evaluate its mineral resources. The study area is located 1n Lake County, OR, about 45 miles northwest from Lakeview. The study area is located near the northwest corner of the Basin and Range physiographic province. Tertiary Picture Rock basalt with tuff interbeds underlies the area (Travis, 1983). No mineral resources were identified; no mines, prospects, claims, or mineralized areas exist in or adjacent to the Diablo Mountain study area.

Jan 1, 1987

Preventive maintenance practices are listed in the manufacturers&apos; instruction books. In general, equipment that requires frequent and extensive preventive maintenance is generally the most costly. The manpower spent on these frequent trips to remote areas is such that it is usually better to invest in a more costly system which requires little preventive maintenance. The best preventive maintenance for the system is a good installation. 7.2 Preventive Maintenance and Inspections With any system, periodic inspection is required because of the corrosive atmosphere and adverse conditions that exist in underground mines. These inspections can spot potential trouble in the system. Repair or replacement at that time averts the possibility of losing effectiveness of all or part of the system. 7.2.1 Cables Approximately once per month all cables in the communications system should be inspected for kinking, chafing, cracking, wear, stretching, or other signs of physical abuse. Particular attention should be paid to cable glands at the entry or exit points to the various units in the system, where the cable goes around sharp corners, in the vicinity of holding cleats which may be clamping the cable too tightly causing potential damage, and across the areas where the cable is exposed to physical damage from outside sources, such as equipment or falling objects. If a cable is damaged, it should be replaced as soon as possible. It is mandatory that the ground leads and connections to carrier current phones be thoroughly inspected and maintained in good condition, since considerable hazard may exist to the operator or equipment if a ground connection is broken. 7.2.2 Pager Phones The most readily available test set to determine if a pager telephone is operating correctly is the pager phone itself. The following physical check of the system can be performed at any phone station. 7.2.2a Listen Circuit Remove the handset from its cradle and listen to determine if the circuit is functional, as indicated by the presence of noise or conversation on the line. If no noise or voice signals are present at the handset receiver, take the following corrective action: 1. Operate the handset press-to-talk switch several times. Any corrosion on the contacts of this switch may cause a receiver to be temporarily inoperative. Repeated operation may clear the condition. 2. Open the cabinet and see if the battery cables are properly connected and are making firm contact. Check the handset cable and its connections in the cabinet of the pager phone, and see if there is any evidence of a break in the cable, corroded contacts, or poor connections. 3. Remove the handset receiver earpiece by unscrewing it counterclockwise (to the left), and remove the receiver from the socket. Examine the handset cavity; in some units, a patch of cotton batting or floss is used as a barrier to reduce acoustic feedback in the handset. If the cotton patch has absorbed moisture, remove it and replace with a crumpled ball of soft rubber, stuffed just far enough into the handset so it will not touch the receiver or switch terminals. 7.2.2b Page Circuit and Talk Circuit Push the page switch, squeeze the handset press-to-talk switch, and call any other phone. Release the page switch

Jan 1, 1984

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950