Search Documents

By Eric E. Cather

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 5,100 acre (2,065 ha) Rubicon RARE II area (No. 5026) in the El Dorado National Forest (fig. 1). Work by the Bureau of Mines indicates that potential for mineral resources in the area is low. Samples from small gravel deposits along the Rubicon River and from favorable structures in the area contained smart amounts of economic minerals. A Tertiary river channel near the north area boundary contains gold values as much as $137.60 per cu yd ($180 per cu m) [(gold at $400 per troy oz ($12.86 per g)]. The channel does not cross the study area. Energy resource potential, including oil, gas, or geothermal, does not exist in this geologic environment.

Jan 1, 1982

By Michael J. Friedel

The permeability and flow capacity in unsaturated media are investigated by the U.S. Bureau of Mines for application to in situ copper leach mining. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite-element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1,500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through in situ rubbling. Injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 2010

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 29,020 acres of the 43,165-acre Terry Badlands Wilderness Study Area (MT-024-684) in order to evaluate its mineral resources. Within this report, these 29,020 acres are referred to as the study area. Located in Custer and Prairie Counties, MT, the study area is about 2 miles northwest of Terry. The study area is underlain by essentially flat-lying units of the Fort Union Formation of Paleocene age with some Quaternary alluvial deposits in stream valleys. No mines or prospects were found in the study area. Bentonitic clays and lignite coal units were examined and sampled; however, no clay resources or coal reserves were identified. Estimates of coal resources will be reported by the U.S. Geological Survey in a joint U.S. Geological Survey-U.S. Bureau of Mines publication. Gravel along the Yellowstone River, a source of agate for private collectors, could also be used as sand and gravel aggregate although material on the south bank of the river is closer to population centers and road systems. Clinker found in the study area could be a source of road metal, but is not well situated in relationship to areas of use. No geothermal resources have been identified although water suitable for direct heat applications may underlie the study area. All the area is leased for oil and gas exploration.

Jan 1, 1985

By L. C. IlsLey

A specially recommended cable is a rubber-sheathed cable that has met the minimum performance requirements for cables as set forth in Schedule 20. The first in the series of recommended cables was listed September, 1930, by an ad- vance notice published as Information Circular 6375 which described the conditions under which the cable tests were made. Since that time six additional cables have met the test re- quirements and have been specially recommended. The complete list of specially recommended. cables is as follows: Specially recommended-cables Cable Symbol No. Hazacord No. 2 BM1 Stranding 19 x 7 Hazacord No. 3 BM2 do. Hazacord No. 4 BM3 do. Super-service No. 3 BM4 7 x 19 Super-service No. 2 Super-service No.. 4 BM5 do. BM6 do. Super-service No. 4 BM7 7x 7 Manufacturer Hazard Insulated Wire Works (division of the Okonite Co.) Do. Do. Rome Wire Company (division of the General Cable Corporation) Do. Do. Do. The cables listed were all twin (parallel duplex) cables having outer belts or cov- erings of approximately -inch high-grade rubber compound, and have the same general appear- ance and relative dimensions as the types of twin cables in general use. The cables were tested under conditions designed to show their approximate perform- ance under mine conditions. Only twin-type cables have met these test conditions. Although the recommended trailing cables are much better and safer for mine use than other cables and withstand being run over by a 7-ton car, they should not be considered as 100 per cent safe. The 7-ton car test represents the minimum limit requirement effective at present under Schedule 2-C, but the test car operates on a straight and level track, and thus does not represent the more severe conditions of mine use such as might result from uneven and curved tracks.

Mar 1, 1931

By Oliver Bowles

From the most remote periods of civilization stone has been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns), or single markers, to great obelisks and pyramids or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1650 at an estimated cost of $50,000,000 or more and is today an object of unusual interest for travelers. Other magnificent memorials both ancient and modern are to be found in many lands. No sharp line can be drawn between buildings and monuments, because the larger types of memorials such as the Bok Singing Tower, Lincoln and Jefferson Memorials, and mausoleums of various types have features in common with buildings. However, great care must be exercised in selecting a site for a quarry that will produce acceptable monumental stone because appearance as well as quality is of prime importance. The deposit must be of uniform texture and attractive color and must be notably free of knots, hairlines, impurities, incipient seams, or other defects. Many memorials are of polished stone, and spots or streaks that might be virtually Invisible on a natural rock face will appear distinctly on a polished surface. Hence, stone to be polished must be selected with unusual care. However, less flawless stone may be used for hammered surfaces.

Jan 1, 1955

By M. O. Serbousek

The load-transfer mechanics of fully grouted roof bolts in coal mines have been investigated in laboratory and analytical studies. The purpose of this Bureau of Mines research is to increase understanding and better interpret data from routine field pull tests and to develop a numerical model of a grouted bolt that can be used in a global computer model of a mine roof. Analytical studies using closed-form solutions and finite-element techniques were compared to experimental results. Laboratory work includes variation of bolt length, hole diameter, and grouL type. Pull tests were pel'fol·med on 4-, 2-, and I-ft bolts in holes of 1-and I-3IB-in diameters. Both polyester resin and inorganic grouts were used as the anchorage medium. Strain gauges were installed on the bolts at several locations to observe the rate of load transfer from the bolt through the grout to the rock mass when a force was applied at the bolt end using standard jack pull testing procedures and equipment. The average anchorage length of 4-and 2-ft bolts was 22 in. Grout type and hole size variations did not produce a significant effect on the rate of load transfer from the bolt to the rock.

Jan 1, 1987

By Sean Gallagher, Rhys Llewellyn, Jay Mattos

This paper contains the results of an examination of accident, injury, employment, and production information reported to the U.S. Department of Labor's Mine Safety and Health Administration (MSHA) and provides information on some of the measures longwall mine operators are using to prevent accidents In all industries, technological advances play a key role in determining those who will survive as competitive participants in an increasingly global marketplace. While mining is among the most basic of industries, technological change is neither unfamiliar nor unwelcome to miners. Historically, technological advances in mining, particularly coal mining, have tracked closely with fluctuations in demand. In the early 1900's, coal accounted for more than three quarters of all the fuel consumed in the U.S. To meet this tremendous demand, underground cuffing machines were introduced, resulting in faster, more efficient coal extraction. Transporting coal to the surface, however, remained labor intensive. In the 1920's, nearly all underground coal was still being hand loaded. Demand for coal then declined as the price of oil, natural gas, and electricity became competitive. In the late 1930's and throughout the duration of World War II, coal demand and production was high. By 1940, more than half the coal mined was being mechanically conveyed to the surface. In 1948, the continuous mining method was introduced in the U.S., further accelerating the extraction process. By the 1950's and 1960's, however, coal production again declined as railroads converted to diesel fuel and gas and oil provided a larger share of the home heating market. Underground coal mines required even more mechanization to remain competitive as an energy source. The first longwall system was introduced in 1960. By 1995, longwalls were producing more than 189 million tons of clean coal annually, surpassing continuous mining production for the second straight year. The mining of coal and other materials has not come without a huge loss of life and considerable human suffering. More than 103,000 workers died from injuries in U.S. mines in the last 85 years. Between two and three thousand miners died each year from the turn of the century until 1931, many from underground fires and explosions. The U.S. has witnessed a tremendous drop in fatalities in underground coal mines. Credit for that is due to safety inspections and enforcement activities, better safety awareness and practices among management and labor, improved ventilation, the use of safer equipment, and increased mechanization which removed many miners from the hazards at the face and also reduced the size of the mining work force. There is little doubt that longwall mining has greatly increased underground coal mine productivity. The degree to which longwall mining has contributed to a safer work environment for underground miners is more difficult to ascertain.

As part of remote sensing research on an abandoned mine lands (AML) site in the Colorado Springs, Colorado area, a geographic information system (GIS) database was generated. This GIS database contains information on the locations and extents of abandoned underground coal mines, the geology of the area, subsidence features and degrees of subsidence risk, topography, drill hole locations, and lineaments (linear features) related to subsurface geologic structures. A GIS database allows the reproducible and accurate comparison and analysis of any data sets which geographically overlap and are within the same coordinate system. The database has been released to the public domain so that government agencies, researchers, educators, and the general public can access this coherent database for the purposes of better understanding the study area and GIS technology. Data files and maps are available in formats that are compatible with the GIS software used in the research project and with most CAD systems so that as many people as possible can make use of the majority of the database. This document serves as the data dictionary for the database by providing descriptions and origins of the data files.

Jan 1, 1992

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By S. J. Pearce

One phase of the work of the Bureau of Mines in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory-protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus,3/ gas masks,4/ supplied-air respirators (hose masks, air-line respirators, and abrasive-blasting helmets, hoods, or masks),5/ dispersoid (dust, fume, and mist) respirators,6/ and nonemergency gas respirators (chemical-cartridge respirators).7/ Approval tests of self-contained breathing apparatus are conducted under the supervision of mining engineers of the Accident Prevention and Health Division} Region VIII; approval tests of other types of respiratory-protective devices are conducted by the Health Branch.

Jan 1, 1952

"INTRODUCTION These safety standards for anthracite mines have been prepared for use as a guide for Federal inspectors. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7282 issued in May 1944 and used as a guide in Federal inspections. No provision made in these safety standards should be construed or operate to nullify any existing State statutes; they are intended to supplement the State statutes in the interest of increased mine safety. Mines are inspected in accordance with the Federal Coal-Mine Inspection and Investigation Act of 1941, Public Law 49, 77th Congress, H. R. 2082. Any unusual hazard noted by an inspector and not covered by these standards will be discussed in the inspection report, and suitable remedial procedure will be recommended.ARTICLE I. - SURFACE STRUCTURESSection 1. Breaker and cleaning plant.Electric switches and controls in breakers and cleaning plants should be enclosed.Where coal is dumped at or near air-intake openings, reasonable provisions should be made to prevent the dust from entering the mine.Section 2. Lamp houseNaphtha or other flammable liquids in lamp houses should be kept in approved containers or other suitable dispensers.Flame safety lamps should be permissible and maintained in permissible condition.Flame safety lamps should be properly cleaned, examined, and assembled by a qualified lamp attendant or other competent person before each period of use. Lamp assembly should again be checked by the person using it immediately before he enters the mine.When not in service, methane indicators, flame safety lamps, and electric cap lamps should be in the custody of competent persons responsible for maintenance and testing."

Feb 1, 1948

By James A. Wasson

This Bureau of Mines report summarizes the application of pilot flooding in the evaluation of a potential waterflood project. Aspects of pilot flooding discussed include choice of pilot location, confined and unconfined waterfloods, operational precautions, and comparison of predicted with observed performance. Summaries of published methods of pilot flood data analysis for determination of full-scale waterflood feasibility are presented and their use illustrated for example pilot flood data.

Jan 1, 1974

By Gary A. Kingston

Chromium resources in the United States are estimated at 1.8 million tons of recoverable chromium contained in 22.5 million tons of chromite-bearing material. Additional resource is presumed existent in large, but as yet undetermined, quantities of material containing less than 10 percent Cr203. No domestic resources are being mined presently (1969). Excluding transportation charges to domestic consuming areas, the total 1.8 million tons of chromim is estimated to be available, in ore or concentrate, at costs up to $0.64 per pound; 63 percent of the total is available under $0.11 per pound; and 38 percent under $0.08 per pound. It is judged that transportation from the resource areas to the existing market centers would add nearly $0.05 to the cost of a pound of chromium contained in ore or concentrate. Technically effective beneficiation methods have been developed for much of the known domestic resource, and further development might reduce costs of processing these materials. However, at present, domestic chromium resources are noncompetitive with foreign sources.

Jan 1, 1970

By M. G. Zabetakis

At ordinary temperatures and pressures methyl ethyl ketone (MEK)-air mixtures containing between 2.0 and 11 vol.-pct. MEK and methyl isobutyl ketone (MIBK)-air mixtures containing between 1.5 and 7.5 vol.-pct. MIBK are flammable. However, MEK-bromochloromethane (BCM)-air mixtures containing at least 6.2 vol.-pct. BCM and MIBK-BCM-air mixtures containing at least 7.0 vol.-pct. BCM are nonflammable. Also, MEK-BCM-air and MIBK-BCM-air mixtures containing less than 18.7 vol.-pct. oxygen are nonflammable. To assure the formation of nonflammable mixtures when mixed with air, MEK-BCM vapor mixtures must contain at least 1.6 vol. BCM per volume MEK, and MIBK-BCM vapor mixtures must contain at least 2.8 vol. BCM per volume of MIBK; these quantities of BCM would be produced by liquid mixtures containing 55 vol.-pct. BCM in the first case and 60 vol.-pct. in the second. An MIBK-BCM-trimethylene chlorobromide mixture containing equal volumes of each liquid forms nonflammable mixtures with air at ordinary temperatures and pressures. The same is true of a liquid mixture containing 34.6 pct. (liquid volume) BCM, 34.b pct. perchloroethylene, 15.4 pct. MIBK, 7.7 pct. toluene, 3.85 pct. ethyl amyl ketone, and 3.85 pct. trimethylene bromide.

Jan 1, 1960

By JOSEPH F. CULLEN, Dorsey A. Lyon

In connection with its investigation looking to the prevention of waste and the increase of safety and efficiency in the mineral indus- tries the Bureau of Mines has undertaken a study of the possible uses of the electric furnace in metallurgy. This bulletin presents a com- pilation of such data as seem to be useful for the information of persons who may be interested in the matter. In the application of electricity to metallurgy three kinds of processes are involved, namely, mechanical, thermal, and electrolytic. Under the mechanical application of electricity come those proc- esses of dressing and concentrating ores that are known as either electrostatic or electromagnetic processes. In electrothermic processes the current is used as a source of heat. The fundamental differences between the various types of electric furnace that are at present in commercial use relate to the manner in which the electric current is applied, as may be noted by reference to that part of this report in which the subject is discussed. In electrolytic processes the electric current is used for depositing metals from solutions. The process may be conducted in one of the following ways: (1) The material to be treated may be put into solu- tion and then electrolyzed, the material thus treated forming the electrolyte; (2) the material to be treated may form the anode or be placed in contact with the anode; or (3) the material to be treated may form the cathode or be placed in contact with the cathode. This report treats of electrothermic processes, with the possible exception of those for the reduction of aluminum from its ores. Moreover, of the processes used in the so-called electrochemical in- dustries only those for the reduction of an ore to metal, or to a com- pound of the metal that is of value in itself, or is an aid in metallurgical work, are here discussed.

Jan 1, 1914

By STUART R. BRINKLEY, Ruth F. Brinkley

This same phonomonon of diffraction may be transposed into the X-ray domain. All that is necessary is to reduco, in the samo proportion, the wavo length of the light and the diameter of the particlo; thus, with radi- ations whose wave length is of the ordog of angstroms, the dimensions of the active particles go from 10 to 100 A that 18, the dimensions of col- loidal particlos. The evidence of this fact is shown by the following experimental schomo (fig. 1a): A narrow beam of X-rays passes through a thin layer of a modium containing micelles; the photographic film is placed a few centimeters behind the sample, and a small absorbing screen stops the direct beam in order to prevent its fogging the film. The intersect of the direct beam is surrounded by a narrow spot whose blackness decreases with the distance from the center. We will call this the spot of central diffusion (fig. 1b). The phenomenon, in spite of its relatively reat intensity, has been observed only by a few authors, who have simply given a qualitative description without attempting any quantitative de- ductions. This is due to the fact that observation of this phenonenon is not possible with the apparatus generally used to obtain X-ray diagrams, because the parasite foggings in the vicinity of the incident beam are sufficiently important to hide those produced by the sample. With the monochromator, however, used by us to obtain Debye-Sherer diagrams, this parasitic diffusion can be totally suppressed. In this way our attention was again directed to the spot of central diffraction, and we were led to make a detailed quaititative study of it.. then several papers have been published on this subject. Hosemann, using methods of calculation outlined by us, has extended them to the special case of fibrous substances, Kratky, on the other hand, starts from an entirely different theoretical point of view; ho examines the case, not of scattered particles, but of closely packed particles. 6ince We will now describe the experimental methods, summarize the calcu- lations needed in the elaboration of diagrams, and finally review the first results obtained in the vast domain of these new physical-chomical studies.

Dec 1, 1946

By G. R. Hopkins

One of the largest items in the expense of operating a refinery is the cost of the fuel used in distillation and for miscellaneous purposes such as in the heating of buildings and in the generation of electricity, On a B. t. u. basis, the average refinery consumes approximately one-tenth as much fuel as it produces. Theoretically, the fuel consumption at refineries should be much smaller than this, but furnaces can riot be designed to be 100 per cent efficient' and, in addition, a large part of the waste heat is low-temperature heat which would not pay for the expense of recovering it. Annual surveys of fuel consumption at refineries have been made by the United States Bureau of Mines, beginning with 1925. During the 5-year period, 1925-1929, the refineries made steady progress in fuel economy. This is evidenced by the Computed figures of heat requirement Per barrel of crude oil refined, which show a decline from 829,000 B. t. u. in 1925 to 639,000 B. t. u. in 1929 (see fig. 1). In 1930, however, the trend in fuel economy was reversed and the quantity of heat utilized in refining the average barrel of crude oil rose to 672,000 B. t. u. There were undoubtedly a number of reasons for the apparent decrease in fuel economy at refineries in 1930, chief of which were the tendency to carry the distillation farther instead of merely topping the crude and a gain in the consumption of waste oils, such as acid sludge, which in actual practice yield less heat per unit consumed than has been theoretically assigned to oil. The consumption of natural as fuel at refineries has declined since 1927, but this has been more than compensated by a rapid increase in the use of refinery or still gas. The total consumption of oil as refinery fuel in 1930 was not much below the 1925 total, but the consumption of coal has declined rapidly, so that in 1930 liquid and solid fuels contributed only 56 per cent of the total heat units- utilized at refineries as compared with 77 per cent in 1925 (see fig. 2).

Jan 1, 1931

By G. R. Palmer

Using a fluidized, countercurrent multiple-compartment ion-exchange (MCIX) column previously developed by the Bureau of Mines, Bureau researchers have successfully extracted uranium from a simulated acidic in situ leach liquor that contained 150 ppm U30s? This successful demonstration of the MCIX system is reported, and the effects of varying the operating conditions on the performance of the system are also examined. Operating the MCIX system with a flow rate of 15 gpm/ft2 and an aqueous-to-resin flow ratio of 200:1, more than 90 percent of the uranium Has extracted, and a resin containing approximately 28 grams U308 per liter was produced. The absorption column used to investigate the operating variables was approximately 18 feet long with a 2-inch ID and was divided into compartments that were 1 foot long.

Jan 1, 1980

By F. R. Cattoir

Analytical methods are presented in this paper for determining soluble titanium, total titanium, indicated titanium, and average effective valence in titanium chloride - sodium chloride mixtures. In addition, data are given showing the effects of coarse and fine grinding on the degree of oxidation and average effective valence of such samples. INTRODUCTION The Electrometallurgical Experiment Station at Boulder City, Nev., as part of the Bureau of Mines program to obtain more efficient utilization of our natural resources, has been developing and improving titanium extractive metallurgical methods and techniques since 1945. Numerous reports have been published describing development of the Kroll process,4/ the electrorefining technique,5/ and methods of analyzing titanium sponge.6/

Jan 1, 1957

By Hsin Wei Wu

A real-time Diesel Particulate Matter (DPM) monitor has been developed on the basis of the successful National Institute of Occupational Health and Safety (NIOSH) designed Personal Dust Monitor (PDM) unit. The objectives of a recently completed Australian Coal Association Research Program (ACARP) study were to modify the PDM to measure the submicrometre fraction of the aerosol in a real-time monitoring underground instrument. Mine testing focused on use of the monitor in engineering evaluations to determine how conditions can be improved. Studies, including a selection during Longwall (LW) moves as described in this paper, demonstrated how DPM concentrations from vehicles fluctuate under varying ventilation and operational conditions. Correlation between the current SKC DPM measurement system and real-time DPM monitors were conducted and results from six mines show a correlation between elemental carbon (EC) and the new monitor DPM mass ranging from .51 to .81 with R2 >.90. These differences are suspected to be due to variations from mine to mine in aspects such as mine atmospheric contamination, vehicle fleet variations, fuel type, engine maintenance, engine combustion efficiency, engine behaviour or interference from other submicrometre aerosol. Real-time monitoring readily reflects the movement of individual diesel vehicles and allows pin-pointing of high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. DPM monitoring approaches that have been available for some time based on shift average monitoring do not readily allow successful engineering evaluation exercises to determine acceptability of pollution levels. Identification of high DPM concentration zones allows efficient modification of mine ventilation, operator positioning and other work practices t o reduce miners? exposures without waiting for laboratory analysis results.

Jan 1, 2010