Search Documents

By R. W. Huber

While conducting an investigation on electrolytic reduction of magnesium oxide in 1943, it became necessary to obtain accurate data on the conductivity and density of various mixtures of fused chlorides. AZ the required information was not available in the technical literature, or there were inconsistencies in the data from several investigators, an independent study was made at the Bureau of. Mines laboratory at Salt Lake City on the conductivity and density of the molten chlorides MgCl2, CaCl2, BaCl2, KCl, and NaCl and the binary mixtures of MgCl2 with the other four chlorides. Studies were also made on the binary system KCl-CaCl2 and on certain portions of several ternary systems. Measurements covered a temperature range from the melting point to 1,000° C. The results of this study were reported in an intra-Bureau report prepared early in 1944. Since then the Bureau of Mines has received several requests for data on fused chlorides; the results of the previous study, therefore, are being published to make the data available.

Jan 1, 1952

By F. P. Haver

The purpose of this investigation was to determine the effect of common impurities, that is, oxygen, nitrogen, carbon, and iron, on the Brinell hardness of electrolytic titanium. On a weight basis, nitrogen had the greatest hardening effect, followed by oxygen, carbon, and iron in order. The hardening effects of oxygen and carbon were almost identical up to a concentration of approximately 0.1 percent by weight. Above this concentration, the relative hardening effect of carbon decreased rapidly, possibly because of its limited solid solubility in a-titanium. Hardness vs. composition curves for both oxygen and nitrogen were essentially straight lines over the range of Brinell hardness numbers (B.h.n.) covered in the investigation. The hardness of titanium was also determined as a function of the percentage of impurity atoms. On this basis, iron in concentrations up to 0.17 atomic percent had a greater hardening effect than either oxygen or carbon. INTRODUCTION Determination of the as-cast hardness of arc-melted titanium is a method of quality control widely used in industry. Numerous studies4/ have been made of the effect of impurities on the hardness obtained by this method. However, most of them have been based on the use of either iodide titanium or commercially pure Kroll sponge (B.h.n. >90), as a starting material.

Jan 1, 1959

By C. W. Davis

Two general schemes have been used for the determination of gold and silver in material containing considerable quantities of copper ; one is known as the " all fire " method , and the other as the , " combination " , or " wet and dry" method . The all fire crucible method , using an excess charge of litharge , has been found satisfactory when the copper content of an ore is under 6 per cent , ( Loevy , J. , Zur Edelmetallbestimmung in hochprozentigen Kupfererzen : Chem. Ztg . Jarhrg . 35 , 1911 , p . 278 ) , or where the precious metal value is so great that a small sample can be used . In the latter case , silica is added until the copper ratio is sufficiently low . If there is more than 6 per cent of copper in an ore , the lead button obtained from a crucible fusion will require repeated scorification before . it can be cupelled successfully . Rescorification is not only tedious , but also causes a slag loss of precious metals . In combination methods , the copper is dissolved , and the gold and silver in the residue . is determined by fire assay Although some combination methods have given satisfactory results for gold and silver , they are not applicable when an estimation of the platinum metals is required . Since substances containing platinum are frequently high in copper , a study of methods which might be used for the estimation of small quantities of gold , silver , and the platinum metals in such material was considered worth while . The estimation of platinum in ores by fire assay methods has been described in Technical Paper 270 of the bureau; ( Davis , C.W. , The detection and estimation of platinum in ores : U. S. Bureau of Mines Tech . Paper 270 , 1921. ) the present paper , which is supplementary to that report , deals chiefly with the application of combination methods , taking them up to the point where the fire assay is to be applied .

Mar 1, 1921

By V. R. Spironello

The Bureau of Mines is conducting studies of the slags related to ferrous technology to evaluate acceptable substitutes for the auxiliary flux, mineral fluorspar, in foundry operations. This work is directed toward the Bureau's goal of minimizing the Nation's dependence on scarce and critical minerals Comparative basic practice cupola (18-inch-ID) trials were made to evaluate a waste material called "used potlining," which contains significant levels of fluorine, sodium, and aluminum in various compounds. Used potlining is recovered from alumina reduction cells after its useful life, and was supplied by the Aluminum Co. of America (Alcoa) to the Bureau for evaluation. The material in the lump and pelletized form (with limestone) provided extremely fluid slags based on visual observation during cupola operation. No adverse effects were found on cupola performance, metal and slag chemistry, the environment, or mechanical properties of the castings produced. Fluorine recovery in the slag was equal to, or higher than, that of fluorspar; fluorine losses to the scrubber water and solids were lower. The acidity of the scrubber Hater was somewhat neutralized. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag and visual inspection. The recovery of sodium in the slag, presumably as the oxide, significantly increased slag fluidity, suggesting that less than equivalent fluorine may be required. There was no contamination of the gray iron by the aluminum from the used potlining. Used potlining was completely satisfactory as a substitute for fluorspar in cupola ironmelting.

Jan 1, 1981

By F. W. Wood

The method described may be used to delineate irregularities, inclusions, porosity, or shrink holes in ingots up to 43 inches in length. Rou¬tine testing does not require technical personnel, and the equipment is easily maintained. INTRODUCTION For a number of years, the Northwest Electrodevelopment Laboratory of the Bureau of Mines, Albany, Oreg., under contract with the Atomic Energy Commission and the Naval Reactors Division of the Bureau of Ships, has studied the production of zirconium and has adopted the Kroll magnesium-reduction process3/ as the, most economical means of producing high-purity zirconium sponge in quantities commensurate with demand. Consumable-electrode arc melting4/ provides a practical means of melting the sponge without increasing the impurity content. The ultimate application for which the metal is intended requires that strict specifications be met to insure workability and maintain the nuclear properties and corrosion resistance. The control measures employed to satisfy these specifications include chemical, spectrographic, and metallographic analyses, mechanical and corrosion tests, and ultrasonic inspection of the finished ingot. The primary purpose of ultrasonic inspection is to augment the other control measures by checking the soundness of each ingot leaving the laboratory. An incidental but important function has been the revelation of information leading to better understanding of the arc-melting process. For example, information obtained through ultrasonic inspection relative to the occurrence and distribution of porosity in ingots has resulted in a. modification of melting practices that minimizes the occurrence.

Jan 1, 1955

By Thomas E. Green

A gas volumetric method was developed for determining metallic aluminum at the 0.01-to 0.3-percent level in 100-gram samples of recycled glass. The method is based on the measurement of the change in gas volume produced by the reaction 2 Al + 2 NaOH + 2 H2O ? 2 NaAl02 + 3 H2 using a simple apparatus assembled from readily available glassware. Apart from sampling errors, the precision of the method is within ±5 percent. A minor modification of the apparatus would extend the method to larger samples or samples of higher metallic aluminum content. Metallic iron and metallic zinc do not interfere at the concentrations found in recycled glass recovered from incinerator residues.

Jan 1, 1971

By J. Koster

During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report.6/ The geology of the Marysvale region has been reviewed recently.7/ The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.

Jan 1, 1939

By J. Koster

During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report.6/ The geology of the Marysvale region has been reviewed recently.7/ The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.

Jan 1, 1939

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

By John S. Dunning

This paper is one of a series describing methods and costs of recovering sand and gravel from deposits in the United States and deals directly with the operations of the Atlas Sand, Gravel and Stone Co. at Farmington, Conn. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production costs. It is recognized that publication of total costs might in some instances cause embarasement to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue.

Jan 1, 1933

By Wilbur I. Duvall

A linear array of shot and gage holes 30 feet deep in a granite outcrop was used to compare the size and shape of radial strain pulses produced in the rock when short cylindrical charges of cast composition B were detonated axially or at one end. The axially detonated charges produced radial strain pulses that had shorter rise times and larger peak strain than the strain pulses produced by end detonated charges.

Jan 1, 1965

By Russell R. Trengove

The Bureau of Mines developed by core drilling the Cove Meadow copper property, also known as the Patterson property, from May 6, 1949, to August 6, 1949. It is in the Cove Meadow mining district, northwestern Humboldt County, Nev., 102 miles northwest of Winnemucca. The purpose of the work was to determine possible reserves in a mineralized shear zone in andesite that has been partly explored by several surface cuts and two shallow underground workings. Production from this zone to August 1, 1,949, was 98 tons of hand-sorted copper ore assaying 5.1 percent. The development work performed by the Bureau of Mines comprised a study of the geology, mapping the area, sampling the outcrops, and exploring by diamond drilling the shear zone adjacent to the fault. Seven holes were drilled for a total of 1,246 feet. Mineral reserves indicated by the project are confined to a length of 500 feet along the strike.

Jan 1, 1950

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous flotation tests of weathered mica pegmatite ores from Alabama and North Carolina to determine the technical feasibility of recovering commercial-grade mica concentrates. A new anionic-catonic method was developed for recovering mica in the presence of clay slimes. In continuous tests, concentrates containing 98.1 percent mica were obtained from the Alabama pegmatite ore; the North Carolina pegmatite ore concentrates contained 97.2 percent mica. The recoveries were 83.8 and 81.6 percent, respectively.

Jan 1, 1965

By T. A. Sullivan

High-purity vanadium metal was prepared by electrorefining commercial vanadium in a molten sodium bromide, potassium bromide, and vanadium dibromide electrolyte. Variables investigated were operating temperature, current densities, electrolyte composition, and condition of the anode. The purity of the refined metal was in the range of 99.95 percent vana-dium. Iron and oxygen in the 50- to 250-ppm range were the only major impurities. Metal with hardness numbers of 50 to 60 in the Rockwell F scale was prepared from feed material with a Rockwell B hardness of 90. The arc-melted metal was highly ductile and could be cold-worked into sheet or foil.

Jan 1, 1965

By Gerald V. Gibbs

As a part of the Bureau of Mines long-range program in asbestos, synthetic asbestiform compounds and minerals were prepared and described. Fundamental structural data on two such compounds are given in this report. Crystallographic data are provided for the synthetic isotypic compounds potassium-lead silicate, K2.Pb4 -Si8021 (I), and lead-aluminum silicate, Pb2. Pb4 .Al2Si6O21 (II). The space group symmetry 14/mmm was assigned provisionally to I and II on evidence of single crystal and piezoelectric measurements. A statistical evalua¬tion of indexed powder diffraction data revealed the cell edtes of I to be a 11.816 and c 7.932A and those of II to be a 11.723 and c 8.044A. The phases are uniaxial with observed refractive indices eD 1.790, an ?D,699 and eD 1.884, cusp 1,807, respectively. The atomic structure of I and II may be based on a complex of chains of silicon-oxygen tetrahedra lying along the c cell edge similar to the type of chain structure postulated by Pauling for scapolite. K2.Pb4.Si8021 and Pb2.Pb4 Al2Si6021 were first described by Geller and Bunting (5, 6)4 as fibrous compounds similar in crystal habit to asbestos. These authors gave powder diffraction data, although no attempt was made to find the cell edges or to index the powder diffraction patterns. Later, Shell and others (9) conducted a crystallochemical study of these fibrous silicates in search of a substitute for strategic asbestos. Their single crystal data revealed K2.Pb4 -Si8021 to be tetragonal body-centered with cell edges a 11.66, c 7.95 A. Pb2.Pb4 Al2Si6021 was concluded to be isotypic with K2.Pb4 -Si8021 on the basis of similar powder diffraction patterns, chemistry, and physical properties. No attempt was made, however, to index the powder diffraction record nor to determine the appropriate space group of either compound.

Jan 1, 1962

By K. C. Dean

A flotation method was developed by the Bureau of Mines for concentrating pollucite, a cesium-aluminum-silicate mineral that may contain from 20 to 40 percent cesium oxide. Separation of the pollucite from three typical ores was achieved by froth flotation of the associated micas, feldspars, and other gangue minerals, using sulfuric and hydrofluoric acids and a cationic-type collector. A low-tenor, 8 percent cesium ore from Maine was upgraded to 20 percent cesium with recovery of 87 percent of the cesium. Relatively high- grade ores from Canada and Southern Rhodesia were beneficiated at lower ratios of concentration to 28 and 29 percent cesium content respectively with recovery of over 92 percent of the cesium. In addition to concentrating the cesium content of ores, the method also effectively separates cesium from sodium, potassium, and lithium, and in certain ores from rubidium. This is accomplished by selective froth flotation of the alkali metal-bearing gangue minerals such as lepidolite, other micas, and feldspars. Since the alkali metals, especially potassium and rubidium, are difficult to separate chemically or thermally from cesium to prepare high- purity cesium products, separation by physical mans is important.

Jan 1, 1962

By Leonard Obert

A triaxial procedure is described for measuring the modulus of elasticity and Possion's ratio of stress relief cores , that is , the concentric hole cores obtained by the overcoring technique . The elastic constant determinations can be made at stress levels comparable with those encountered in underground mining . The results from tests on an aluminum alloy calibration specimen and four rock specimens are included .

Jan 1, 1964

By Charles L. Kimbell

This study summarizes and amalgamates much information collected, compiled, and utilized by the Bureau of Mines numerous country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other volumes of the international studies of the Minerals Yearbook. Because of the plethora of sources used in preparing these regional studies, it is impossible to cite all sources of information used in preparing this summary, but some recognition seems due. Generally speaking, the preparation of this study, and its related detailed studies on countries and areas, would be impossible without the efforts of the personnel of our counterpart agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or in publications of central statistical agencies in their countries, are the foundations upon which this work rests. Thus, we must begin by expressing our appreciation to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1992

By D. A. Reynolds, J. D. Davis

"INTRODUDTION Investigations by the Bureau of Mines have shown that the carbonizing properties of splint and bright coals may differ greatly. In a study of 55 coal columns selected from representative coals of the Appalachian region, Sprunk and coworkers 10/ compared various chemical and physical properties of splint and associated bright coals. Carbonization tests in the Fischer retort at 932°F. (500°C.) showed that, except for bright coals of high oxygen content, the coke residue from bright coal was much more swollen and cellular than that from splint. ·with one exception, agglutinating values determined by the Bureau of Mines test, were lower for splint than for associated bright coal.Because sorting of coal in quantity is tedious and time-consuming, separate types have not been carbonized by the Bureau of Mines-American Gas Association (BM-AGA) test, which requires 85- to 200 pound charges. However, this method has been used to determine the carbonizing properties of samples 0f bed layers that are composed largely of either splint or bright coal.4/ In these earlier tests, which were made at high temperatures on layer samples from the Elkhorn bed, Letcher County, Ky., the splint coal yielded more coke than the bright coal, and this coke was slightly stronger than that from the bright coal. The cokes from samples with large proportions of bright coal were more cellular or porous, as were the low-temperature cokes obtained from carbonization of separated samples of bright coal in the Fischer retort."

Apr 1, 1944

By Frank J. Wiebelt

Work on the Abbott-quicksilver property was part of the general program of th~ Bureau of Mines in its investigation of domestic mineral resources, which are essential to national defense or industry and of which our present or probable future supplies are inadequate. The mine was discovered in 1862, and the intermittent production up to 1947 has totaled around 37,500 flasks of quicksilver. Output has come from ore shoots formed in the vicinity of fault intersections in a narrow zone composed of lenses of silicified serpentine breccia interbedded with shale. Work by the Bureau included the drilling of six diamond-drill holes aggregating 2,845 feet. Several possible ore zones were intersected by the drill holes. Field work was begun in April 1948 and concluded in October of the same year. This report gives detailed results of the diamond drilling and a brief account of the history and description of the ore deposits.

Jan 1, 1949