Search Documents

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By H. S. Caldwell

The objective of this investigation by the Bureau of Mines was to develop and test for laboratory use a retort embodying many features required for practical commercial-scale applications of vacuum distillation of metals. A gas-fired vacuum retort was developed comprising a hollow, cylindrical graphite liner encased in a thin shell of stainless steel. The liner prevents the shell from collapsing under vacuum and protects it from corrosion by metal vapors and the molten metal charge. The vacuum-tight shell protects the liner from oxidation and flame erosion. The retort was used to distill zinc from dross and die-casting scrap. More than 99 percent of the zinc was recovered as a condensate containing 99.8 to 99.9 percent zinc. (Atmospheric distillation recovers 95 to 98 percent at a purity of 99.5 percent zinc.) Distillation rates of 50 pounds of zinc per hour were attained at a temperature of 65° C. with pressures ranging between 50 and 100 microns. Distillation at this low temperature is not practicable at atmospheric pressure. Also, the retort is suitable for distilling other volatile metals such as cadmium and magnesium.

Jan 1, 1961

By H. P. LeVan

Research was conducted to examine the feasibility of extracting manganese from Georgia umber ore by a three-stage continuous sulfuric acid-ferrous sulfate pickle liquor leaching process. A continuous cyclic process for treating the umber was operated successfully, using a synthetic solution simulating a ferrous sulfate fortified anolyte solution discharged from a manganese electrolytic cell as the leaching medium. Leaching efficiency based on removal of the manganese from the ore ranged from 83 to 89 percent for all systems tested.

Jan 1, 1965

By Jean M. Kenney

Frequencies of haulage-related accidents in metal and nonmetal surface mines for the years 1988 through 1990 were investigated and compared with those of non-haulage-related accidents. This study was part of the U.S. Bureau of Mines program to improve mining haulage safety. Data were obtained through the U.S. Bureau of Mines Accident Data Analysis (ADA) program. The chi-square test was used to compare frequencies of haulage-related and non-haulage-related accidents for each of the following variables: degree of injury, age, total number of years of mining experience, and shift time. Significance was determined for degree of injury between haulage-related and non-haulage-related accidents. Age of injured did not vary significantly between haulage-related and non-haulage-related accidents, but total number of years of mining experience was found to be significant. Shift time for the accident proved to vary significantly between haulage-and non-haulage-related accidents. Events causing injury for haulage-related accidents were tabulated, and the most frequent determinants of haulage-related accidents were identified. Accident descriptions for both fatalities and permanent disabilities were studied, and the primary causes of these accidents were identified. These findings suggest that haulage-related jobs are among the most dangerous when considering accidents experienced by all workers in the metal and nonmetal surface mining work force.

Jan 1, 1993

By M. W. Pullen

It is recognized that the determination of electrical resistivity of the earth within a given area may furnish information concerning the location of certain mineralized strata of economic importance. Present knowledge of the electrical resistivity of the various rock formations is almost nil, and the geophysicist who is detailed to make a survey of an area without any data as to the relative resistivity of the underlying rocks is greatly handicapped. Such surveys are usually made within areas known to contain mineral deposits to aid in locating desirable points for drilling. Usually these areas have been prospected by diamond drilling, and drill cores of the various rocks and ores are usually obtainable. Were it possible to make resistivity tests in a laboratory of the drill cores or from pieces of the rocks and ore within an area before attempting a field survey, this would indicate not only the advisability for such a survey but would aid considerably in the interpretation of the results of such a survey. To be of most value a definite method should be used for all such tests, and as yet such a method has not been established.

Jan 1, 1929

By Suzann C. Ambrosio

Cameroon's mining industry continued to be dominated by crude petroleum. The value of petroleum output was estimated at $1 billion.2 The 1982 gross domestic product (GOP) was approximately $8.4 billion. During 1981, crude oil export revenues increased in value 30%, comprising approximately 56% of Cameroon's total export earnings. The 1982-87 5-year plan emphasized, hydrocarbon and agricultural development and targeted the exploitation of bauxite and clay deposits. New petroleum legislation was promulgated on November 26, 1982. Public Law No. 82-20 detailed hydrocarbon companies' obligations concerning oil and gas discoveries and exploitation. In general, the Cameroon Government has participated in joint ventures with private companies and has levied a 57.5% petroleum tax plus adjustable royalties. Exploration expenses were paid by concession holding companies, and the Government in the past has reimbursed 50% of expenses under certain conditions.

Jan 1, 1984

By Paul S. Schopf

The results of an experimental investigation into the possible use of medium energy acoustic fields (130 to 140 dB) to precipitate 1 to 10 micron particles is presented. The aerosol was produced with a LeMer generator using oleic acid and nitrogen. The sound field was a sinusoidal standing wave field in an acrylic tube, with light transmission data used for concentration determination. The results showed collection efficiencies of up to 80% on 2 micron particles with a residence time of 11.8 seconds at a sound pressure level of 139 dB re 2x10-5 N/m2. A discussion of the possible turbulent mechanism is made, as well as review and comparison with others? work.

Jan 1, 1972

By G. Dale Coe, Will H. Coghill

The " periodic pincer " herein described fills a need for a device to control the rate of flow of a wet ore pulp through an orifice . Two uses of the periodic pincer to be discussed are on classifiers and on a wet ore feeder . Although the immediate necessity that brought about this device was for better operation of a miniature hydraulic classifier , in connection with an investigation of iron- ore concentration being conducted by the Federal · Bureau of Mines , with the cooperation of the University of Alabama , the device has promise of a wider field of application . In the iron - ore work , the need became so acute for a nonchoking , uniform - delivery classifier spigot that development of a suitable device was imperative .

Apr 1, 1944

By A. J. Forney

Recent experiments used catalysts of plate assemblies in synthesizing high-Btu gas and gasoline indirectly from coal. A gas with a heating value of 925 to 943 Bt-: per cubic foot has been prod u la the hot-gas-recycle pilot plant from synthesis gas (3H2+100) with lathe turnings used as catalyst in the first reactor, and assemblies of parallel sprayed plats of nickel in the second. Solid plates made of Raney nickel, and steel and aluminum plates sprayed with Raney nickel or nickel oxide were tested. Those catalysts had very low resistance to gas flow; 90 percent lower than nickel granules used in previous experiments. In a single stage of synthesis thee nickel plates were only partially successful. Although the heating values of the product gas ranged from 856 to 941 Btu per cubic foot, the carbon monoxide content of he gas was above 0.1 percent. Both steel and wrought turnings were tested in single-stage synthesis, but the conversion of hydrogen and carbon monoxide was too low to attain the desired heating value of 900 Btu per cubic foot in the product gas. Assemblies of plates thermally sprayed with fusel iron were tried in an experiment to make gasoline. A gasoline yield of 52 percent (of the hydro¬carbons produced) was obtained using a 1H2-10O feed These sprayed assemblies were in service for 1,500 hours, the longest that this type of catalyst has been used. When a second reactor containing Raney nickel catalyst was added in series with the first reactor, complete utilization of the feed gas was obtained because in addition to the liquid product, a high-Btu gas with a heating value of 800 Btu per cubic foot was made.

Jan 1, 1965

By James S. Browning, W. H. Eddy

Laboratory batch and small - scale continuous flotation tests were conducted on a ferruginous barite - fluorspar ore from near Sweetwater , Tenn . , to determine the feasibility of producing commercial - grade fluorspar and barite concentrates . The lignin sulfonate - sodium fluoride - fatty acid method of floating fluorspar produced acid - grade concentrates . Flotation of the barite from the fluorspar tailing using petroleum sulfonate yielded concentrates suitable for use as a weighting agent in oil -well drilling muds . The continuous flotation tests , treating about 150 pounds of ore per hour , yielded fluorspar concentrates that assayed 98.3 percent CaF2 and barite concentrates that assayed 91.2 percent BaSO4 . The recovery of the two minerals was 91.2 and 85.2 percent , respectively .

Jan 1, 1964

By David L. Veith

Caustic scrubbing followed by silica flotation with cationic ether primary amine proved effective in upgrading commercial magnetic concentrates to supergrade products containing 2 percent SiO2, or less. Samples representing 41 million long tons per year of commercial magnetic concentrates from the Lake Superior region were tested by the Bureau of Mines. Bench-scale and pilot plant research indicated an estimated potential of 32 million long tons per year of superconcentrates to be available. Two pilot plant investigations yielded superconcentrates containing 1.1 and 1.9 percent SiO2 that were derived from commercial concentrates containing 7.0 and 4.2 percent SiO2, respectively. Corresponding iron recoveries were 90 and 93 percent at reagent costs of just over 33 cents per long ton of superconcentrates produced. Additional sources evaluated on a bench scale resulted in iron recoveries of 72 to 95 percent in products containing 1.7 to 2.0 percent Si02. Although reagent cost ranged up to 60 cents per long ton of superconcentrate, it is probable that these costs would be reduced in plant applications where benefits are derived from material and reagent recycle.

Jan 1, 1974

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959

By Joseph J. Wallace

1. From the standpoint of present production and recoverable reserves, there are two beds of major importance in Allegheny County -Pittsburgh and Upper Freeport -and one of lesser importance -Redstone. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 832 million short tons as of January 1, 1953. Of this total, 768 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By V. H. Gottschalk

Among the procedures developed by the Germans for providing the tonnage of iron powder needed to make rotating bands for artillery shells is the use of a ceramic tunnel kiln, not only for finishing the reduction of centrifugal powders but also for making so-called "brickyard sponge iron," which, after crushing and grinding, seems to yield a product suitable for powder-metallur- gical purposes. The final report issued jointly by the German Powder-Metallurgical Society (DPG) and the Chemical-Metallurgical Branch of the Research Depart- ment of the Metallgesellschaft, Inc. (ZFC of MG) gives the available details of this procedure, which may be regarded as a further development of the process in commercial use since 1911 at a ceramic plant in Hoeganaes, Sweden. The Bureau of Mines' wartime development of the Hoeganaes process also cul- minated in the adaptation of ceramic tunnel kilns for carrying out the solid- carbon reduction of iron ores, and comparison with the German technique should further advance the art. This information circular is issued as a supplement to Bureau of Mines reports of investigations Nos. 3819,2 3822, 3841,2 and 4271, on brick- yard sponge iron and is based on four German reports entitled "Making Iron. Powder in the Tunnel Kiln," translated from FIAT microfilm reel H-46, frames 9190-9209, 9280-9299, 9339-9357, and 9377-9384 (PB L 70042), which represent the four original research reports, Nos. 2005, 2008, 2010, and 2012, respec- tively, of the Metallgesellschaft, Inc.

Aug 1, 1948

By D. H. Platt

Bauxite, the principal source of aluminum, has been mined from deposits in Saline and Pulaski Counties, Ark., since 1899; war needs have greatly stimulated production. Many of the ore deposits are basin-shaped and either outcrop or are covered by a shallow-depth overburden at their peripheries; these are mined by stripping and open-pit methods. When stripping becomes economically impracticable, incline shafts or slopes are sunk on the dips of the deposits, and underground mining is done on the retreat, using a room-and-pillar method.

Jan 1, 1945

From 1886, the first year shipments were recorded, until 1939, the Leadville district produced over 3,500,000 long tons of manganiferous ore. Of this total, metallurgical-type ores comprised 27 percent and manganiferous iron ores suitable for fluxing in lead smelters made up 73 percent. In 1939, the Bureau of Mines, as part of the strategic minerals investigative program being conducted at the time, requested the Mineral Industries Survey Section of the Mining Division to make a comprehensive study of the manganese resources of the Leadville area. This investigation, owing to the caved and flooded condition of the underground mine workings, was necessarily confined to a study of old maps, production records, and geological reports, and the results were published as an Information Circular in July 1940.

Jan 1, 1949

By Robert Howard

With the rapid depletion of the Peerless Coal Co.'s mine in Spring Canyon, it was necessary, if the company was to remain in the coal-producing business, to look to the development of a new property or to acquire a mine already developed. After careful investigation of several operating properties it was decided by the officials of the company to take over the lease on an undeveloped acreage held by a private party in Price Canyon, about 3 miles north of Castle Gate, Utah.

Jan 1, 1930

By Donald W. Mitchell

Certification tests for urethane-foam systems and techniques for apply-ing foam safely in mines are described. Fire hazard from foam exists if flame propagates beyond the ignition source or penetrates the foam. Foam that passes the certification tests can be applied on stoppings, continuous sections of ribs of relatively wide passageways (with no foam on the roof), short sections of roof such as overcasts, roof cavities, and intersections (with no foam on the ribs), and between buntons on one wall of a shaft. Foam on the ribs and adjoining roof presents a fire hazard. Stoppings covered with foam passing the certification tests are resistant to penetration of heat, flame, and smoke than similar stopping without foam. Flame propagation can be arrested by water sprays. Spontaneous ignition of foam can be prevented.

Jan 1, 1966

By C. Edward Chamberlain

A Bureau of Mines procedure was developed for the analysis of volatile matter in airborne coal dust-rock dust mixtures prior to, and resulting from, coal mine fires and explosions. Dust in the 10-to 20-mg weight range can be analyzed. Volatile matter is determined by a greatly scaled-down version of the empirical macro-scale method used by the Bureau. The alkaline earth carbonates in the rock dust are dissolved in acid prior to the volatile matter determination of the residue, and the rock dust content is calculated from the analysis of calcium and magnesium by atomic absorption.

Jan 1, 1974

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spin trapping methodology has been used to study the reactions of manganese dusts with glutathione, employing a-{4-pyridyl-1-oxide)·N-tert-butyl-nitrone (PBN) and 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as spin traps. The results show evidence for the glutathionyl radical formation in the reactions of both MnO2 and manganese (Ill) acetate with glutathione. Based on these experimental observations, we hypothesise that the mechanism of neurotoxic effects of manganese might be due to the fact that the generation of glutathionyl radicals depletes the glutathione pool and reduces the glutathione shield against free radical products of dopamine metabolism and manganese induced reactive oxygenated species. IntroductionExposure to manganese compounds often occurs as the result of foundries and mining operations (1. 2). Other significant sources of environmental manganese include coal-fired power plants and burning of residual and crude oil (3, 4). Lately gasoline combustion has also started to contribute since manganese (methyl cyclopentadienyl manganese tricarbonyl. 0. 125 g/gallon) is being used instead of lead as an antiknock ingredient in automobile fuels (5. 6). Although manganese is an essential element in certain biological processes it is toxic in excessive amounts. The manganese toxicity is mainly associated with the nervous system (7-9). Symptoms frequently observed in manganese poisoning or manganism are disorientation, memory loss, anxiety, compulsive laughing and crying, mask-like faces, akincsia rigidity and tremor (10). In spite of numerous investigations to understand the mechanism of manganese induced injury. it has not been possible to localize the initial chemical lesion responsible for altered physiology and ultimate cell death. This may perhaps he the reason for failure in developing a successful therapy for manganese intoxication."

Jan 1, 1990