Search Documents

By G. M. Molinda

The U.S. Bureau of Mines conducted an investigation to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure and suggestions for controlling this problem are presented. Hazardous roof conditions identified in some mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52 pct of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath several valleys in the form of bedding plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomena, was found at mining depths as great as 300 ft. In situ, horizontal stress measurements beneath a valley and the adjacent hillsides, confirmed valley stress relief. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress.

Jan 1, 2010

By M. R. Geer

The Bureau of Mines examined the washability data for 25 Appalachian coals requiring low-density washing to reduce sulfur content to 1 percent, using the distribution-curve method. The purpose was to estimate how closely theoretical sulfur values could be approached, what yields of washed coal could be expected, and the recovery efficiencies that might be achieved. Assuming that the run-of-mine coal would be crushed to 3/8 inch and cleaned in dense-medium cyclones, the calculations indicate that theoretical sulfur contents could be approached closely when cleaning at a specific gravity of separation as low as 1.30. With coals that have favorable specific gravity compositions the recovery efficiency anticipated for cleaning at 1.30 specific gravity is surprisingly high. Similar calculations for cleaning with concentrating tables at intermediate specific gravities indicated that theoretical sulfur contents at 1.50 specific gravity could be approached closely with some coals but not with others. The calculations suggest that operating a table at a specific gravity of separation much lower than about 1.50 probably would be unsatisfactory with most coals.

Jan 1, 1968

By R. B. Prater

The Bureau of Mines conducted research to separate the F from byproduct Zn concentrates obtained from fluorspar (CaF2) production, as part of the Bureau's effort to devise efficient, environmentally acceptable technology for recovering Zn from resources considered undesirable by Zn producers. Sulfuric acid (H2SO4) was found to be effective in F removal, while ammonium carbonate [(NH4)2C031 was not. The most important variables for reducing the necessary residence time were found to be temperature and agitation. Optimum leaching conditions were 75° C and 500 r/min for 2 h at 40 pct solids with 0.2 g acid per gram of concentrate, which resulted in a 98.3-pct F extraction. Zinc losses during F removal were in the range of 2 to 3.3 pct. Other elements such as Fe, Cd, Ca, and Cu were also partially dissolved. About 93 pct of the F was removed from the leach solution by neutralization and precipitation with calcium hydroxide [Ca(OH)2]. Additional treatment might be necessary to limit the buildup of soluble elements in the recycled leach solution.

Jan 1, 1985

By R. L. Hopkins

Some typical thiacyclopentanes and thiacyclohexanes were synthesized to provide reference compounds needed for the identification of sulfur compounds in crude oils. Two general methods of synthesis were employed: (1) cleavage of 2-alkyltetrahydropyrans with hydrogen bromide followed by the reaction of the resulting dibromoalkanes with sodium sulfide and (2) the catlyzed reaction of cyclic ethers or 1)4-or 1)5-alkanediols with hydrogen sulfide. Both methods produced mixtures of 2-alkylthiacyclopentanes and 2-alkylthiacyclohexanes with 2-alkyltetrahydropyran as the starting material. The structures of the reaction products were established by analysis for sulfur; desulfurization; gas-liquid chromatography (GLC); mass, infrared, and nuclear magnetic resonance (NMR) spectra; and an alternate synthesis. The synthesis of the cyclic sulfides contributed substantially to the identification of 10 members of this class of sulfur compounds in crude oil.

Jan 1, 1967

By Donna D. Harbuck

The Bureau of Mines has investigated a process to produce titanium powder directly from titanium salts. If successful, such a process could lower the cost and increase the use of titanium. In this study, K2TiF6, K2TiF3, and TiF3 were reduced with potassium in the temperature range of 650° to 750° C. Under certain conditions, titanium powder 1.6 to 3.3 microns in size was produced. After leaching the product with a 0.1M HCl solution, powder impurities as low as 0.04 pct potassium and 0.28 pct fluorine were obtained. However, oxygen levels of over 1 pct and the frequent formation of insoluble byproducts demonstrate the need for further research to make the powder suitable for powder metallurgy applications.

Jan 1, 2011

By V. C. Petersen

The titanium-rich end of the titanium-germanium system was investigated by x-ray and metallographic methods and verified by resistivity and dilatometer measurements. A constitution diagram is proposed. The titanium-rich portion of the phase diagram is characterized by eutectic and peritectic reactions. The eutectic composition is 19 percent germanium, and the eutectic temperature 1,360° C. The peritectic reaction occurs at 905° C. and 4 percent germanium. Germanium is soluble in alpha titanium to a maximum of 4 percent at 905° C. and in beta titanium to a maximum of 12.5 percent at 1,360° C. Both limits of solubility decrease with decreasing temperatures. Although substantial quantities of germanium are soluble in beta titanium, beta is not retained on quenching. The beta phase probably transforms to alpha by a martensitic reaction.

Jan 1, 1957

By E. T. Bowers

The Accident Analysis (ADA) computer program was developed at the Spokane Research Center (SRC) to provide a rapid broad-based analysis of mining accidents. Because the Bureau of Mines often needs this type of information for the development of viable research programs the ADA program was written to access and analyze accident data available frog the Labor Department's Mine Safety and Health Administration (MSHA). This report describes the ADA program, the data it uses, and the potential value it has for planning mining research.

Jan 1, 1987

By J. W. Town

Recrystallization studies on chrome-bearing spinel materials were made by the Bureau of Mines to determine the effects of certain fluxing agents and cooling rates on the chromium-to-iron ratio of recrystallized spinel. Statistically designed and evaluated tests showed that the ratio of chromium to iron in naturally occurring chrome spinel could be increased from 1.5 to 1 to over 7 to 1 and that the ratio of chromium to iron in the chrome-spinel in a stain-less steel slag could be raised to over 18 to 1. Silica, magnesia, and lime had significant positive effects, while alumina had a significant negative effect. Cooling rates of 200 C per hour in a programmed spiral globar electric furnace were satisfactory for growing crystals of recoverable size.

Jan 1, 1967

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Bolivia has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW All useful substances of the mineral Kingdom belong originally to the State. The soil and subsoil are regarded as two distinct parts, the latter extending indefinitely in depth (Art. 2). The subsoil is under the dominion of the State, which may either abandon it to common use, grant it gratuitously to the owner of the soil, or alienate it, in return for an annual fee, to any individual or association that applies for it. (Art. 1-3.)

Jan 1, 1929

By Jr. Hill

Laboratory metallurgical treatments of three high-iron bauxite ores from Arkansas were conducted to determine the relative effectiveness of experimental methods for recovering alumina and a commercially acceptable iron concentrate. The standard for evaluating recoveries from experimental processes was the Al2O3 recovery from Bayer digests of the crude ores; recoveries from digestion of the three ores were 74.1, 87.4, and 88.7 percent. Flotation, magnetic separation, or various combinations of digestion, calcination, and reduction-sintering, leaching, and magnetic separation of leach residues failed to produce Al2O3 recoveries as high as the standard. A high-iron-bearing fraction, containing between 68 and 78 percent of the total iron, was produced in a three-phase treatment involving a caustic, lime reduction-sinter of the crude ore, water extraction of Al2O3 from the sinter, and magnetic separation of the leach residue.

Jan 1, 1967

By C. G. Maier

The present trend of chemicometallurgical research toward widespread and inclusive use of thermodynamic methods requires the inclusion of available data of this sort in any comprehensive metallurgical report . Such data for manganese are far from adequate for the full utilization of these methods . Even if our knowledge of these properties is weak , the collection of available figures is nevertheless well worth while , especially if their utilization in an approximate way may show inherent possibilities of application . No less important is the necessity for discovering the vital gaps in the existing information , to serve as a basis for further pertinent study . The utility of the thermodynamic methods of Lewis and Randall ( 234 ) 3 has become increasingly evident to metallurgists . It is true that at present no better approach to the general , fundamental problems of chemical metallurgy is available than close adherence to these methods . The effort is here made to collect and correlate , as far as possible , significant quantitative thermodynamic data on manganese and its metallurgically important compounds . There are considered here only the intrinsic properties of pure materials . The order maintained as far as possible will be as follows :

May 1, 1934

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By Robert C. Ellman

Stockpiles containing 2.3 million tons of lignite constructed in the period 1948-56 in conjunction with the construction of Garrison Dam on the Missouri River demonstrate successful stable long-term storage of lignite. Uniform and thorough compaction of each of the I-foot-thick layers by which the piles were constructed produced a bulk density of 70 Ib/cu ft. Air penetration into the stockpiles was restricted to a degree that prevents spontaneous heating or deterioration of the stored lignite, A continuing record of observations beginning with stockpiling operations in 1948 has been accumulated, This includes periodic fuel analysis, analysis of pile gases, and measurement of pile temperatures on the first large stock-pile, pile 5. This report describes the stockpiling method, the changes in heating value, pile gas composition, and pile temperature and summarizes observations from 1953 to 1964, Data accumulated attest to the stability of the stored lignite. The variation of the average heating value of periodic pile-depth samples is only 160 Btu/lb (11,990 to 11,830) on the moisture" and ash-free (maf) basis during almost 10 years of storage. Temperature levels of the pile interior are progressively decreasing. At pile surface, cyclic variations occur with the season. The only problem encountered with the large stockpiles is wind and water erosion of the pile surface. The partially successful control measures used are described.

Jan 1, 1967

By F. N. Kissell, C. H. Elder, C. M. McCulloch

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By Richard A. Winters

In 1985 at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 9,400 acres of the 10,005-acre Duncan Creek Wilderness Study Area (ID-111-78) in order to evaluate the mineral resources. The study area is located in Owyhee County, 10, about 36 miles southwest from Bruneau, ID. No mining districts are in the study area, nor were any mines or claims recorded or found. The southern half of the area was covered by oil and gas lease applications, all of which were cancelled prior to June, 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Duncan Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By P. C. McWilliams

The Bureau of Mines investigated ground support problems in four major block-cave mines to assess the current "state-of-the-art" and to delineate areas for future research. The most significant problem is the inability of present support systems to hold moving ground. Further, as mining progresses to greater depth, this problem becomes more serious. Providing adequate temporary support capable of withstanding primary and secondary blasting is the next most significant problem. A detailed analysis of the effect of mining methods on support problems is also recommended for future research.

Jan 1, 1975

By Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average Sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining.

Jan 1, 2010

By J. B. Zink

The Bureau of Mines developed a spectrochemical method to determine six constituents in coal ash in the following concentration ranges: silica 9 to 63 percent, alumina 7.5 to 35 percent, ferric oxide 2 to 30 percent, calcium oxide 1 to 29 percent, magnesium oxide 0.5 to 6 percent, and titanium oxide 0.5 to 4 percent. Samples of coal ash are fused with a mixture of lithium tetraborate and vanadium pentoxide. The resulting beads are crushed, mixed with powdered graphite, and briquetted. The pellets are analyzed spectrographically, using controlled high-voltage spark excitation. Vanadium serves as the internal standard. Effects due to matrix variations are minimized by fusion with lithium tetraborate. Intensity ratios of selected analytical lines are determined photometrically, Concentrations are read from analytical curves, prepared from synthetic standards, relating log intensity ratios to log concentration. A combustion procedure is used to determine sulfur tri-oxide. The method is most useful when large numbers of coal ashes must be analyzed but a high degree of accuracy is not essential.

Jan 1, 1967

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By M. M. Wong

Electrolysis of titanium carbide and a material consisting of titanium, carbon, nitrogen, and oxygen as soluble anodes in Used electrolytes was investigated by the Bureau of Mines for the preparation of crude titanium metal. Tests made in all-chloride electrolytes showed only a low recovery of titanium as well as a substantial volatilization of titanium trichloride (TiC13) when present in the electrolyte. Electrolysis at 750° to 850° C in a mixture containing 85 percent NaC1-15 percent potassium floutitanate (K2TiF6) yielded as high as 91 percent recovery of titanium from titanium carbide and 62 percent recovery of titanium from the titanium-carbon-nitrogen-oxygen material. Problems associated with the preparation of crude metal by fused-salt electrolysis are discussed. The crude metals produced from both anode materials were electrorefined in a sodium chloride-titanium chloride (NaCl-TiC12) electrolyte, and ductile titanium metal was obtained.

Jan 1, 1963