Search Documents

By Alla D. Mah

The energies of combustion of two carbides of tungsten and two carbides of molybdenum were measured , and the corresponding standard heats of combustion were derived . The results are as follows : WC : AH298.15 ( combustion ) = -285,940 ± 250 cal /mole , W₂ C: AH298.15 (combustion ) = -490,660 ± 400 cal /mole , Mo₂ C : AH298.15 ( combustion) = -439,350 ± 600 cal /mole , MoC : AH298.15 ( combustion ) = -269,800 ± 1,000 cal /mole . The combustion heats were combined with the heats of formation of the corresponding metal trioxides and carbon dioxide to obtain the following heats of formation : WC : AH298.15 ( formation ) = -9.6 ± 0.4 kcal /mole , WC: AH298.15 ( formation ) = -6.3 ± 0.6 kcal /mole , Mo₂ C : AH298.15 (formation) = -11.0 ± 0.7 kcal / mole , MoC : AH298.15 (formation ) = -2.4 ± 1.0 kcal /mole . The heats of combustion and formation of MoC are tentative .

Jan 1, 1963

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By John C. Cook

This was a study to identify and evaluate known technologies employing electromagnetic resonance phenomena in solid minerals for their identification and assaying, particularly assay logging of exploratory boreholes. A comprehensive literature search and study revealed some little known NMR (nuclear magnetic resonance) techniques developed by Professor G. J. Béné's group at the University of Geneva, Switzerland. These are suitable for use in weak, inhomogeneous magnetic fields. Laboratory NMR tests of numerous U.S. ore minerals showed good identifying signals from phosphates, fluorspar, bauxite, oil shale, and spodumene (lithium) ores, but not from the copper, lead, antimony or manganese ores tested. Use of EPR "signatures" for such ores is suggested. A conceptual design for an NMR assay logging system is proposed.

Jan 1, 1978

By W. M. McKewan

This U.S. Bureau of Mines report discusses wire ropes used for hoisting in U.S. mines. The in-formation presented was extracted from a large body of data compiled by the U.S. Mine Safety and Health Administration (MSHA) using a data base management system (DMS). Further, these extracted data were then manipulated to provide tables of data that show the types and amount of wire rope used for hoisting. This report describes the different types of wire ropes and how a DMS can be used to manipulate MSHA's wire rope inventory data. The data indicate that more 1-1/4-in-diam ropes, 6x27 construction ropes, and right lang lay ropes are used in U.S. mines than ropes of any other diameter, construction, or lay type.

Jan 1, 1991

By J. P. Walsted

Offgrade chromite concentrate, with a Cr-Fe ratio of 1.3 to 1.4 has been successfully smelted to produce useful ferroalloys. The Cr-Fe ratio is not improved, but the alloys can be used without a too drastic change in normal steel-mill practice. The ordinary high-carbon ferrochrome has been successfully produced by smelting under highly acid smelting conditions. An alloy containing 50 percent chromium was produced at a power consumption of 4,490 kw.-hr. per ton of alloy. Alloys containing 20 percent silicon were made by direct smelting chromite concentrate and silica.

Jan 1, 1956

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By Launa G. Mallett, Charles Vaught, Dana C. Reinke, Lisa J. Steiner, Lynn L. Rethi, Kathleen M. Kowalski-Trakofler, Jr. Brnich, William J. Wiehagen

Safety and health professionals recognize that training is a critical element of any effective safety and health program. An extensive literature survey has led the authors to conclude that we are at the beginning of a revolution in training due to changes in the demographics of the workforce, the rapid growth of technology, and the universal ascendance of the information age. Of present major concern in the mining industry is how to provide appropriate training for an aging workforce and concurrently develop training for the expected influx of new and less experienced miners as older workers retire. This report explores the key issues in the changing safety and health training area as identified by the multidisciplinary team of NIOSH researchers who conducted the literature survey. Issues include generational differences between newer mine workers and the present workforce with respect to their physical, psychological, social, and cultural characteristics; their learning styles and work expectations; and the impact of technology. Some preliminary conclusions are offered for future training needs.

Jul 1, 2004

Coal mining in Indiana is limited to the south-western portion of the state, with coal currently being recovered in 19 counties. The coal-producing area of the state covers approximately 6,500 square miles. Although most of the coal in Indiana is recovered by surface mining methods, a small percentage is recovered through underground mining. To date, 40 percent of the known coal reserves have been removed. Indiana has about 33 billion tons of identified coal reserves, of which approximately 17 billion tons are recoverable using current technology. Of this recoverable coal, about 15 billion tons are recoverable by underground mining and 2 billion tons are recoverable by surface mining methods. The State of Indiana has regulated the environmental impacts of coal mining since 1941. Indiana was the second state in the nation to pass legislation requiring mined land reclamation. Its SMCRA regulatory program was approved July 29,1982, and its Abandoned Mine Land Program was approved July 29, 1982.

Jan 1, 1992

By S. L. Weber, V. Castranova, D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, M. Bhat

"The mechanism of bleomycin-induced pulmonary fibrosis is not ye: clear. Recent studies have shown that alveolar macrophages (AM) can be stimulated by bleomycin in vitro releasing inflammatory cytokines, suggesting that the interaction of bleomycin with AM is an important step in the drug-induced fibrotic process. Bleomycin is known to bind DNA and generate oxygen radicals through complexation with Fe2+ and oxygen. To provide,more insight into the cellular oxidative property of bleomycin, v.s have developed a fluoromicroscopic method using 2',7'-dichlorofluorescin diacetate (DCFHDA) as an oxidative fluorescence probe to study the deomycin-induced intracellular oxidation in rat AM and the inhibition of the oxida¬tion by taurine, a compound known to inhibit the bleomycin-induced fibrosis. Bleomycin at 5 to 20 ug/ml has a moderate stimulatory effect (1.87- to 2.66-fold) on the secretion of superoxide anion. A high concentration of bleomycin (20 ug/ml), however, inhibits cell response to zymosan-induced secretion of superoxide anion. At 4 ug/ml, bleomycin has no effect on cell membrane integrity or morphology but results in a significant increase in intracellular oxidation. This oxidative process is Fe2-,-dependent and is accompanied by an increase in intracellular calcium (35 nM). Both the intracellular oxidation and calcium rise induced by internalized bleomycin are inhibited by pretreatment of cells with varying concentrations of taurine (25, 125, and 187.5 uM). The inhibitory effect on intracellular oxidation .vas found to be 36, 57, and 60%, respectively. These results demonstrate a stimulation-inhibition relationship between bleomycin and taurine on re cellular oxidation at a subcytotoxic dose of bleomycin, suggesting that the oxidative effect of the intracellular bleomycin-Fe2 complex is important in the initiation of the fibrotic process. — Environ Health Perspect 102 (Suppl10):91-96 (1994) IntroductionThe pulmonary system is most susceptible to oxygen radical-induced diseases due to its constant exposure to the highest oxygen tension, and the potential encounters with oxidant gases such as ozone, nitrogen oxides, and toxic doses of dust particles. The lung is also a well-perfused organ and thereby vulnerable to the effect of circulating xenobiotics such as paraquat, and, bleomycin, which is known to cause pulmonary injuries (1). Alveolar macrophages (AM), which act as a means of defense by phagocytizing inhaled dust particles and microorganisms while increasing production of reactive oxidative species, have been shown to play an important role in mechanisms leading to oxidative lung injury and fibrosis (2-4)."

Dec 1, 1995

"For a good many years the Bureau of Mines and various state mining experi¬ment stations have endeavored to develop some method of utilizing the immense deposits of lignite in the United States. Work in relent year has indicated that the best method of this is to drive off the moisture and most of the volatile water from the lignite in some form of carbonizing apparatus leaving a residue high in fixed carbon and low in moisture and volatile matter, which by briquetting can be made into a high-grade fuel. The earlier forms of carbonizing equipment tried were complicated, costly to build and keep in repair, and could not be operated intermittently without being seriously damaged. During the year 1922, however the Bureau of Mines devised a very simple carbonizing oven which produces a uniformly well carbonized product. This oven is essentially a vertical shaft with means for supplying raw lignite at the top and discharging the carbonized limited at the lower end. Air in regulated amount is admitted to the shaft at two horizons, and a zone of combustion maintained through which the column of lignite passes. The lignite is thus carbonized by construction of its contained matter and a small proportion of its fixed carbon, leaving most of the fixed carbon in the carbonized product or ""char"". The degree of carbonization can be closely controlled by varying the volume of air supplied to the oven and the rate of travel of the charre down the shaft.The ""lignite char"" produced is a soft material resembling charcoal more than coal or coke, but somewhat harder than charcoal. A typical analysis is shown in the table headed ""Fuels,"" further on in this papers."

Feb 1, 1924

By Gary L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from low-grade domestic chromites, which contain silicon and aluminum impurity levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten sodium hydroxide (NaOH) under oxidizing conditions to form sodium chromate (Na2Cr04). The reaction product is leached with methanol to remove the majority of the unreacted sodium hydroxide, then with water to remove the sodium chromate and the remainder of the sodium hydroxide. The sodium chromate product is recovered by evaporative crystallization from the aqueous solution. This report presents results of laboratory tests to determine the optimum fusion conditions and the chromium extractions obtained from several domestic chrotdte concentrates. These concentrates are from a variety of sources, including the Stillwater Complex in Montana, Kanuti River-Caribou Mountain, Red Bluff Bay, Kenai Peninsula, and Kodiak Island areas in Alaska, deposits in northern California, and a nickel-cobalt laterite from southern Oregon. All of these concentrates were successfully treated by the Bureau procedure. The best chromium extrac-tions obtained for each of these materials ranged from 69.5 to 98.9 pet.

Jan 1, 1985

By C. A. Herbert

In summer, when hot, moisture-laden air enters a coal mine in the region east of the Mississippi River, the moisture is likely to condense on the roof and ribs because the incoming air is cooled below its dew point upon contact with the roof, ribs, and floor of the mine passageways. When the roof and ribs become wet owing to this condensation they are said to "sweat." In many mines, as soon as this sweating begins, shale or slate roof that appears solid and strong in winter begins to cut and fall. For a long time most mining men believed (many still believe) that the roof trouble was due to this sweating. However, from observation of conditions in one mine the operators concluded that the trouble was caused by expansion and contraction of the roof due to changes of temperature. This opinion was confirmed by experiments at several mines in cooling the air as it entered the mines. Methods used in these mines for cooling the air are described in this circular. MINE A At mine A the roof gave considerable trouble in the summer, and it was observed that where a spray of water from a leaking dam kept the roof wet and at a uniform temperature no difficulty was experienced with the roof, although it had cut and fallen on either side of that point. From this fact the company officials concluded that changes of temperature in the air rather than moisture caused the trouble and that if the incoming air were cooled to approximately normal strata temperature much of the additional roof trouble experienced during the summer would be overcome.

Jan 1, 1940

By James F. Neill, O&apos

Investigation of the Gilley fluorite deposit was based upon examinations made by several of the Bureau's mining engineers. Fluorspar was found in the dump talus of sloughed and water-filled trenches and shafts, and there were indications that faulting or other dynamic distortions favorable to deposition of this mineral in minable quality and quantity might exist. The inference was based upon a field study of the area and its comparison with fluorspar deposits in Kentucky. The proximity of this deposit to the iron furnaces at Gadsden and Birmingham was a factor that influenced its investigation, as the demand for metallurgical grades of this critical mineral is acute. The present supply for the district is obtained from out-of-State sources, and the value of any local deposit would be enhanced by the saving in freight charges. The Gilley fluorspar deposit is 17 miles east of Gadsden and 50 miles northeast of Birmingham, Ala. Mineral deposits occur as thin veinlets and small bunches of fluorite in upturned bode of siliceous limestone. The ore-bearing structure is a reverse fold, and the mineral deposit appears as a replacement along crumbled zone fractures of the contorted limestone.

Jan 1, 1950

By Jeffrey Y. Foley

In 1980, the Bureau of Mines investigated the northern Darby Mountains on the Seward Peninsula, AK, for radioactive mineral deposits. Uranium is concentrated in silicified shear zones in biotite quartz monzonite of the Darby pluton. The shear zones are best exposed in steep, narrow, avalanche gullies; they are characterized by radiometric anomalies and by uranium and thorium geochemical anomalies. Radiometric and geochemical anomalies are also found over altered biotite quartz monzonite where there are no visible shear zones. The radiometric and uranium anomalies are often spatially, but apparently not genetically, associated with alkaline mafic and felsic dikes. Similar geochemical and radiometric anomalies over discolored altered zones and geochemical anomalies in sediments downstream from the altered zones indicate that additional areas may also be favorable targets for uranium deposits. Analyses of panned, heavy mineral concentrates show no significant concentrations of uranium or thorium in resistant heavy minerals. This indicates that radioactive elements in the Darby pluton are concentrated in soluble, nonresistant minerals that may constitute a recoverable uranium resource.

Jan 1, 1986

By R. V. Ramani, V. T. Burgos, J. A. McClay

Model testing is a two part operation; first, to assure the valid¬ity of the mathematical statements and second, to evaluate the accuracy of the computer model for predictive purposes. Verification of both the conceptual and computational aspects can be achieved through the use of input data for which output results are available for comparison. In this dissertation, two test problems were selected for model testing from the Economic Evaluation Reports of the U.S. Bureau of Mines, Process Evaluation Group. Verification Data Set I Input data for this test was selected from an economic analysis of a hypothetical 1,056,000-ton-per-year mine in a 48-inch bituminous coal seam (Process Evaluation Group-Report No. 72-27, 1972). The mine was scheduled to operate five days per week, three shifts per day, 220 days per year with an estimated life of 20 years. Coal reserves covered an area of 6.4 square miles with an expected recovery rate of 70%. Production was achieved through 4 continuous miner sections with an average production rate of 400 tons per shift. The cost summary in the report included a breakdown of equipment and labor requirements. A depreciation schedule listed the expected capital expense per year of operation, assuming capital replacement with identical units and no change in the unit cost. Supply and oper¬ating costs were listed in both gross annual figures and cost per ton of production. The operating and investment costs were projected over the 20 year mine life and a discounted cash flow analysis performed to determine

Jan 1, 1975

By John W. Finch

The present epoch in human history has been variously described as the age of coal, of oil, of iron and steel, and of power. All agree, however, that it is a great industrial period. Power is of course the vital force in the industrial organism; but power is derived chiefly from mineral fuels or from harnessed and controlled water - also a mineral substance although usually not so classified by industry. However, the latent energy of fuels cannot work for men until it is changed to active energy by combustion and until this active energy is converted into motion. This motion is just as indispensible as the energy itself. Likewise, the latent energy of water cannot be utilized until it, too, is converted into motion; out the mechanisms and devices for converting latent energy into motion, as well as the structures in which they are operated, would not be possible without metals and other minerals. Consequently, minerals are fundamental in industrial civilization.

Jan 1, 1938

By E. J. Gleim

In the mining of coal the trend is toward more and more mechanization. This increased use of machinery to replace hand labor is assuming many new forms and presents a constantly changing aspect. Safety engineers must be alert if the many electrical problems resulting from these new installations are to be handled safely. Some of these problems present possible electrical hazards that may be overlooked by the safety engineer unless they are called to his attention by one who has made a special study of the conditions. The foregoing is especially true of conveyor systems of mining. The terms "conveyor systems" and "conveyor mining" as used in this paper refer to those systems in which various types of conveyors are employed to transport coal away from the working place. In some mines this means complete elimination of track, cars, and locomotives. In others it means that conveyors take the coal from the working place to a convenient loading point, from which transportation is completed by cars and locomotives.

Jan 1, 1941

By F. E. Armstrong

This report describes development and application by the Bureau of Mines of techniques and instruments for using radioactive inert-gas tracers to determine flow paths through petroleum reservoirs that have natural fracture systems and for which water injection has been selected as the stimulative production method. A field test was made to prove the techniques and evaluate instrumentation. The feasibility of applying the techniques and instruments to the solution of reservoir problems in other stimulative methods of production also is discussed. Oil commonly is displaced from sandstone host rocks by the action of a driving force that causes the oil to move through interstices of the rock and into production wells. In addition to the requirements of oil being trapped within the sand pores and the presence of an effective displacement mechanism, the rock itself must have adequate permeability to permit flow of oil and other fluids.

Jan 1, 1961

By J. H. McClain

In the last 3 years' operation of the zirconium-production plant, zirconium metal has been employed to good advantage in many applications. The most frequent use has been in situations requiring resistance to attack by hydrochloric acid. In this service, it has been shown to be a serious competitor to Hastelloy. Zirconium also has excellent resistance to most other corrosives end could be considered for use as an all purpose metal. For example, this report cites 18 applications in hydrochloric acid, 4 applications in sulfuric acid, 5 applications in phthalic-hydrochloric acid, 3 applications in wet hydrogen chloride-chlorine atmospheres, and 2 applications in fused caustic.

Jan 1, 1954

Data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 889 underground (6.0%) and 13,982 surface (94.0%) mining operations.1

Aug 1, 2009