Search Documents

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 6 Listing The following is a listing of the Mine Evacuation Simulation Program

Jan 1, 1976

By W. M. Nabors

As part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers at the Morgantown (W. Va.) Petroleum Research Laboratory are studying secondary oil-recovery projects in the Appalachian region. The increasing demand for petroleum and its products and the increasing cost of exploratory drilling tend to emphasize the importance of improving the recovery of oil from known petroleum reserves. Published reports setting forth the pertinent facts of these operations may help others to profit by the experience. This report presents the results of a study of secondary-recovery methods used in West Virginia by the Piedmont Oil and Gas Co., the Ryan Oil Co., and Water floods , Inc., on their Roane County leases in the Walton and Clover Rush Run pools. The principal oil-producing horizon underlying the area studied is the Big Injun sand, at approximately 2,000 feet. The sand is often referred to as blanket sand because it underlies much of the State and is oil-productive in many localities. Most of the pools in the area were discovered during 1907 to 1910 and were similarly developed and operated.

Jan 1, 1960

By G. R. Hopkins

[Apparent progress in economy at petroleum refineries, as measured by the average amount of hest units required to refine a barrel or crude oil, received a set-back in 1938, when the average rose to 567,000 B. t. u., compared with 562,000 B. t. u. in 1937 (see fig. 1). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 was the decline in total runs to Invariably the average requirement increases when crude inn to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries are masked by the degree to which the capacity is utilized. Additional crude runs give lower average heat requirements in two grays first, because they are mane with the expenditure of cc-comparatively small amounts s of auxiliary heat, and, second, because additional runs generally represent simple topping operations. In 1938 crude runs to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from. 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938.]

Jan 1, 1939

By Marting J. Gavin

The twentieth century has often been spoken of as the age of petroleum, and from many viewpoints it can be justly considered so. Certainly the petroleum industry is one of enormous importance to this country, industrially, financially, and economically. The United States, however, at present producing over 60 per cent of the world's total output of petroleum, is not producing petroleum at a sufficient rate to provide for its own domestic, consumption. For several years this country has been importing increasing quantities of crude and partly refined oils from Mexico, and has been drawing heavily on domestic stocks of petroleum. Production in the United States is increasing, but it is not increasing at the same average rate as domestic consumption, nor is it probable that in the future domestic production will increase sufficiently to satisfy the demands of domestic consumption, but on the contrary, in the opinion of those best qualified to know, the peak in the curve of domestic production of crude petroleum will be reached in a comparatively few years, whereas the consumption of petroleum and its product will increase at a continually growing rate. This country, then, must turn, and as the increasing imports from Mexico indicate, is turning to other sources than the crude petroleum, produced in this country to make up the deficit between domestic production and domestic consumption of petroleum and its products,

Jun 1, 1920

By J. S. Browning

Laboratory and pilot-plant tests of spodumene-beryl pegmatites of the Kings Mountain, N. C., area resulted in development of a new and improved method by the Bureau of Mines for separating and recovering spodumene, mica, and beryl. The process was successfully applied to other domestic pegmatites and a spodumene flotation-plant tailing containing about 0.5 percent beryl. The method comprised soap flotation of the spodumene, using combinations of sodium fluoride and lignin sulfonate as conditioning agents to recover 80 to 85 percent of the contained lithia in concentrates assaying over 6 percent Li20. About 80 percent or more of the beryl was retarded in the spodumene tailing. The beryl subsequently was activated, floated, and cleaned in a secondary circuit to yield beryl concentrates containing 6 to 7 percent BeO. The tests also demonstrated that a good recovery of high-grade mica could be produced.

Jan 1, 1961

By S. H. Ash

A CLAY, sand, and gravel deposit known as the "buried valley" of the Susquehanna River is situated in the Northern field of the anthracite region of Pennsylvania near Wilkes-Barre. The presence of this buried valley and the uncertainty regarding the extent and physical condition of the water-bearing valley-fill deposits have made great care necessary in mining operations to avoid breaking the strata between the mine workings and the valley-fill deposits to the extent that inundation of the mine workings would follow. The principal factor that threatens to cut short the life of the anthracite industry, to curtail production, and to affect the economic structure of the people and business dependent on anthracite for their livelihood is inundation of anthracite mines (6,7).3

Jan 1, 1950

By J. M. Stuve

In this Bureau of Mines investigation, the low-temperature heat capacities of polycrystalline phases corresponding to the sulfide compounds CoSO?89' CoS1?33, and CoS2 were measured by adiabatic calorimetry within the nominal temperature range 5 to 300 K. The derived absolute entropies S298 were 10.36±O.02, 12.96±O.03, and 16.31±O.03 cal?mol-1?K-l, respectively, assuming third-law behavior. In addition, the standard enthalpy of formation 8Hf298 of CoSO?89 was determined by bromine solution calorimetry. The derived value of 8Hf298 was -50.63±2.1 kcal?mol-1, based on the 8Hf298 of Co0. This result is considerably more negative than previously published formation values based on high-temperature gas equilibrium studies.

Jan 1, 1985

By J. P. May

This U.S. Bureau of Mines report identifies and evaluates factors responsible for dump-point accidents involving mobile mining equipment. Information regarding the occurrence and severity of the accidents, the industries affected, the types of equipment involved, the primary and contributing causes, and pertinent Federal regulations is included. The aim of this report is to provide information that will aid mine operators in the recognition of hazards associated with mobile equipment operation near the dump points of stockpiles and waste dumps.

Jan 1, 1990

By Thomas M. Barczak

The Bureau of Mines is conducting research to optimize the capability of mine roof supports so that the selection and design of these supportsare compatible with the conditions in which they are to be employed. This report describes a study that investigates three parameters influencing the load-carrying capability of wood crib supports: height, configuration, and horizontal displacement. Four crib heights, four parallelogram configurations, and three ratlos of horizontal-to-vertical displacements were tested on full-scale wood crib supports in a mine roof simulator. Test results indicated a reduction in load-carrying capability for increases in crib height. Increasing the contact area by changing the intersecting angle between crib blocks to form parallelogram configurations provided a slight increase in load-carrying capability for the first 10 to 12 in of vertical convergence, after which the cribs became more unstable, resulting in significantly less load-carrying capability. Horizontal displacements did not appreciably affect the load-carrying capability of wood crib supports for the range of vertical displacements (less than 10 in) likely to be encountered underground. This report documents these tests and postulates some explanations of failure mechanics for the observed behavior.

Jan 1, 1988

By Joseph J. Wallace

The 1952 Annual Report of the West Virginia Department of Mines lists seven beds that are being mined in Mingo County, of which the Cedar Grove is the most important. The Cedar Grove, Alma, and Coalburg contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 3,007 million short tons as of January 1, 1953. Of this total, 2,396 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By Jim Ploger, Peter W. Johnson

Bus drivers represent a large segment of the US transportation industry and research has shown an association between exposure to Whole Body Vibration (WBV) and the high rates of low back disorders. Impulsive WBV exposures have been recognized as a risk factor for low back injury and new guidelines exist for their measurement and assessment (ISO 2631, Part 5). Methods to accurately and better characterize the impulsiveness of WBV along with the temporal patterns of the exposures are needed. The development of a hardware and software system to measure continuous TWA and raw, impulsive WBV exposures and the design of a subsequent study are presented. Methods Using two Larson Davis HVM 100 as accelerometer amplifiers, small external batteries, and a Pocket-PC (PDA) with 1 Gb of compact flash memory, we can collect up to 16 channels of data for a full day 600 Hz. Tri-axial WBV exposures will be measured and characterized at the frame of the bus and at the driver/seat interface (seatpad accelerometer). Using a repeated measures design, 20 bus drivers will drive on selected routes which include both city streets and highways, and within and between subject components of variability and exposure determinants related to the bus, bus seat, the bus driver, and the route will be identified. Global Positioning System (GPS) data will also be collected and integrated with the WBV exposure data to facilitate the identification of the location, velocity and type of road associated with high average TWA and impulsive WBV exposures. This system may be used to develop administrative (alter speed and/or route of bus, systematically vary type of routes) and/or engineering controls (identify and trigger the need for street repair) to reduce high WBV exposures. Results Our portable Pocket-PC based data acquisition system is up and running and we can collect seven channels of WBV data (seat pan tri-axial accelerometer, bus frame tri-axial accelerometer and GPS data) continuously for a full shift. The software analysis of the data is complex but nearing completion. We have incorporated the vibration dose calculations from ISO 5321, Part 5 and have obtained a Matlab-based routine to appropriately weight the continuous signals. Discussion In summary, the measurement of WBV is complex but new technologies open avenues of collecting and assessing WBV exposures that were previously not possible. The standardization of impulsive WBV exposure assessment methods is needed to further the discipline and better enable comparisons across studies.

Jan 6, 2006

The investigations reported herein comprise preliminary studies to evaluate large scale mining systems adaptable to the thicker oil shale deposits in the deeper central portion of the Piceance Creek Basin. The studies include an evaluation of the geology, hydrology and resources of the Basin., evaluation of a potential prototype mine site, synthesis of rock mechanics data on Green River Formation oil shale, selection and preliminary design and cost evaluation of six potential mining systems and a ranking analysis to aid in selecting the most promising system. Results of the ranking analysis indicate the following four systems to be most promising for large scale underground oil shale mining: - Chamber and pillar (using spent shale backfill) - Sublevel stoping with spent shale backfill - Sublevel stoping with full subsidence - Block caving with LHD's Recommendations for phase II are to investigate the above systems in greater detail, refine present cost data, and perform economic evaluations of oil shale mining using these systems.

Jan 1, 1975

By E. E. Maust

The present work is part of an ongoing Bureau of Mines effort to provide a better understanding of the fundamental phenomena involved in sulfide flotation, the role of oxygen in xanthate adsorption being one essential issue. Galena was chosen as the material around which to develop a conceptual model, partly because of its demonstrated oxygen sensitivity and partly because information on its properties and flotation behavior constitutes the largest part of the fundamental information available on sulfides of commercial importance. The model is formulated primarily in terms of surface electronic energy levels produced by oxygen and xanthate and is further developed using existing experimental evidence and its implications. Four major functions of oxygen are elucidated, and the relationship of these to the formation of lead xanthate, dixanthogen, and a surface compound is discussed. Though yet incomplete, the model provides a useful framework within which the results of diverse experiments can be related to one another in their proper perspective, as shown by a brief discussion and resolution of some apparently discordant results reported in the literature.

Jan 1, 1976

By David D. Walker

The purpose of the investigation was to describe and appraise tungsten deposits in Montana . The work supplements previous investigations made by Pattee ( 10 ) and Walker ( 17 ) in selected areas of the State . Scheelite deposits in tactite are the most numerous and most important economically , having accounted for nearly all of the State's tungsten production . Of the 64 deposits examined during the current study , 50 contained scheelite , 11 hubnerite , 2 wolframite , and 1 ferberite . The State's major tungsten production has been from scheelite deposits in Beaverhead County . The report lists , by counties , the type and grade of each deposit . The more important occurrences are accompanied by geological and assay maps .

Jan 1, 1963

By H. M. Smith

[ ]

Jan 1, 1927

By L. E. Schultze

The Bureau of Mines devised a technique to recover a Zn-Pb concen-trate from a geothermal brine. More than 99 pct of the Zn and Ph was precipitated by treating the brine with H2S and controlling the pH with lime. Recycle of the sulfide precipitates increased crystal size and resulted in easily filterable products. A typical sulfide precipitate contained 53 pct ZnS, 8 pet PbS, 24 pct MnS, and 15 pct FeS. Addition of sulfide as FeS or CaS was not effective in precipitating Zn and Pb, but Zn in the brine was selectively removed with a strongly basic ion-exchange resin. A proposed flowsheet for metals recovery is discussed.

Jan 1, 1985

By B. J. Arnold, F. F. Aplan

"The captive bubble and sessile drop contact angle techniques have been used to evaluate the hydrophobicity of petrographically identified coal macerals. The magnitude of the contact angle on vitrinite is shown to be a function of coal rank ( %C, %0 and % vitrinite reflectance), increasing with increasing rank to a maximum for low volatile bituminous rank coals then decreasing for anthracite. The least data scatter is found when vitrinite reflectance is used as a rank parameter. Contact angles measured or estimated for other discrete macerals, indicate a variation in hydrophobicity based on coal type. These data correlate well with known flotation results. Coal is a heterogeneous mixture of plant remains and associated minerals that have undergone chemical and physical changes by biological and geological processes. These plant remains form coal macerals, discrete organic entities in the coal which have characteristic chemical and physical properties. As the differing chemical nature of each maceral will affect its behaviour in processes such as carbonization the separation of macerals during coal preparation may provide an important asset in coal utilization.Separation of some of the macerals based on specific gravity has been achieved in the laboratory, and by Sun and Cohen , in a study of two Pennsylvania bituminous coal preparation plants. It was indicated that the lighter exinites report almost exclusively to the clean coal while the denser inertinites are concentrated in the higher gravity fractions. The Longwy-Burstlein process6 took advantage of the difference in hardness or friability of the macerals by using impact breakage followed by screening to remove the more friable vitrain,clarain and fusain. The remaining durain, often high in spore content, was then recrushed. The re-mixed fractions produced the optimum size for obtaining the best coke strength for a particular coal.Separation or concentration of rnacerals by froth flotation largely depends on differences in the hydrophobicity of the macerals. Sun and Cohen 5 . indicated an order of decreasing floatability as exinite, vitrinite and inertinite, while a Russian study (as cited by Brown 7 ) showed that vitrains floated more readily than the duller types. More recently, Hirt and Aplan8 showed that 'pseudovitrinite' floats somewhat faster than does vitrinite while fusinite floats very slowly. Olson and A plan found that vitrinite floated easily while substantial quantities of the non-floated coal contained fusinitic material. Burdon noted that vitrinite is more floatable than semifusinite, and Sarker et a/. 11 have shown that vitrinite is selectively concentrated by froth flotation and oil agglomeration. Sun indicated that flotation, based on his calculated floatability index, should decrease in the order clarain, vitrain, fusain and durain; while Horsley and Smith 13 indicated the decrease to be: vitrain, clarain, durain and fusain. These differences can be attributed to the specific coals used in each study and to the individual macerals composing each coal type within a given coal."

Jan 1, 1989

By K. P. V. Lei

The Bureau of Mines investigated molten salt electrorefining 'n helium atmosphere cells as a means for the production of ductile vanadium. 'Electrolytes composed of NaCl-VCl2, LiCl-NaCl-VCl2, BaCl2-KCl-NaCl-VCl2 KCl-LiCl-VCl2, and CaCl2-NaCl-VCl2 were tested. Two electrolytes, KCl-LiCl-VCl2 and CaCl2-NaCl-VC12, were selected for laboratory-scale production tests. A molten salt electrorefining process was developed for the production of ductile 99.6 percent vanadium from a commercial 90-percent grade. Using the CaCl2-NaCl-VC12 electrolyte, an 87-percent recovery of ductile vanadium was made; an 85-percent recovery was made with the KCl-LiCl-VCl2 electrolyte.

Jan 1, 1967

By B. W. Moore

The U.S. Bureau of Mines investigated the separation of heavy rare-earth elements (REE) in an ion-exchange process. An ion-exchange column consisting of two sections, a loading section and a separation section, provides high levels of REE loading and good REE separation with an expected processing cycle of less than a month, while current ion-exchange technology requires more than 5 months. A different resin is used in each section: sulfonic resin in the loading section and iminodiacetic resin in the separation section. The separation section is further divided into two segments: the first conditioned with NH4 and the second with acid. Erbium is loaded onto both segments of the separation column as a retaining ion. Bands of mixed REB eluting between separated bands of pure REB were recycled directly to the column. Without mixed-band recycle, over 80% of the REE eluted from the column was separated into fractions with 99% purity of each element; with such recycle, the percentage of separated elements can be increased to around 90%.

Jan 1, 2010

By Raymond L. Lowrie

Coal deposits in the Boulder-Weld County coalfield in Colorado are analyzed in relation to economic factors governing the growth, stability, and competitive potential of the coal industry. Recoverable reserves, estimated to be 571 million tons, are discussed in detail, particularly those in the Erie and Frederick Quadrangles. Geology of the coal measures, quantity and quality of water resources, and chemical and physical properties of the coal are described. Coal production factors, including mining techniques and equipment, labor requirements, transportation facilities and rates, and markets, are considered for coal's position in competition with alternate fuels. Growth of the fuels market, through increasing thermal-electric power generation in the Denver Metropolitan Area, will stimulate coal production in Colorado. Reserves of the contiguous Boulder-Weld coalfield, if mined in a sustained, year-round, high-tonnage operation, could be used to supply much of that fuel demand.

Jan 1, 1966