Search Documents

By Jasinder S. Jaspal

Most of the underground coal in the United States is mined via room-and-pillar mining methods with continuous miners. These machines operate intermittently because they have to wait for shuttle cars to interchange positions. To overcome this discontinuity in shuttle car haulage and to realize the full production potential of continuous miners, the U.S. Bureau of Mines developed a multiple-unit continuous haulage (MUCH) system through a research contract with Jeffrey Mining Machinery Div. (JMMD). The MUCH system consists of 12 rubber-tired vehicles and a bridge conveyor. The rubber-tired vehicles are connected by a unique mechanical linkage system to form a 250-ft train. The mechanical linkage permits the vehicles to track-retrack the preceding vehicle in both inby and outby directions. The cut coal cascades from one vehicle to another until it is discharged on the section conveyor belt. The MUCH system provides continuous haulage to the continuous miner. The MUCH system was initially surface tested by JMMD. Subsequent extensive testing was conducted by the Bureau at its test facilities at Bruceton, P A. Deficiencies found during testing were corrected. This report summarizes initial tests by JMMD and subsequent extensive tests and evaluation by the Bureau.

Jan 1, 1989

By William R. Roy

Seven coal-related waste samples (mining, cleaning, and gasification) were characterized chemically and mineralogically. Laboratory extracts of each sample, using a variety of different extraction methods, were used in both acute and chronic bioassays. A coal slurry sample (coarse fraction) and two coal cleaning refuse samples were chemically and mineralogically similar, and generated acidic water-waste systems, both in the laboratory and in the field. Acidic laboratory extracts and field samples of acid mine drainage in the area where the solid samples were collected, tended to be in equilibrium with some type of CaSO4 phase and with maghemite. The chemical composition of the extracts was sensitive to the method used to generate the extracts, but generally had the same prevalent chemical character as the field samples. The acidic wastes contain appreciable quantities of soluble Al, Mn, Ni, SO4, and Zn as indicated by both laboratory extraction and field data. Long-term extractions suggest that some constituents (Al, Fe, SO4) continued to be released by the acidic wastes after 22 weeks with no apparent associated change in pH. Two mine spoil samples, essentially shale, tended to generate water-waste systems that were neutral in pH and consequently released lower quantities tit potential pollutants than the acid wastes. The gasification residue was compositionally similar to coal-fired power plant slag and fly ash and generated moderately alkaline extracts with low concentration of soluble potentially toxic constituents. All of the solid wastes contained a variety of organic compounds, many of which are on the EPA Priority Pollutant List. However, these compounds were essentially insoluble in aqueous media. Each extract was tested for acute toxicity with tour species of freshwater aquatic organisms; green sunfish (Lepomis cyanellus), fathead minnow (Pimephales promelas), a crustacean (Daphnia magna), and a snail (Physa anatina). The extracts of the two mine spoil samples and of the gasification residue were not toxic to any of the organisms while the extracts from the acidic refuse and slurry samples were acutely toxic to all of the organisms. For all cases, pH was significantly correlated to mortality while Al, Fe, Mn, Ni, and Zn were significantly correlated to mortality in specific instances. Data from 96-hour LC-50 determinations showed that dilutions up to 1:1000 were necessary to eliminate mortality. The most toxic extracts were those with the lowest pH which necessitated the largest amounts of dilution to eliminate mortality. Chronic bioassays with the same test organisms were investigated with leachate samples from a relatively unweathered refuse sample and an older, more weathered refuse sample. The unweathered refuse sample generated a leachate that was acutely toxic while the leachate from the weathered refuse sample was not acutely toxic. No detrimental chronic effects were noted in organisms exposed to dilutions of the non-toxic leachate while low concentrations of the acutely toxic leachate produced lower hatchability for the Lepomis cyanellus and Pimephales promelas eggs, increased mortality with chronic exposure for Lepomis cyanellus, Daphnia, Physa, and reduced weight gain for Physa. Dilutions of a toxic, high-Fe leachate resulted in the precipitation of ferric hydroxide that was implicated as the major causative factor accounting for the physical and physiological toxic effects exhibited by all of the test organisms in these acutely sublethal concentrations. The toxicity of this leachate demonstrates the potential effects that these types of wastes can have on the aquatic ecosystem if they enter a receiving water in a natural setting.

Jan 1, 1984

By R. L. Brown

This report, the seventeenth in an annual series, summarizes Bureau of Mines research and technologic work on coal and related investigations for July 1, 1951, to July 1, 1952. It 1s based largely on publications issued during the fiscal year, although 10 some instances data are presented that have not been published previously. Footnote references are given to the publications so that further details on the work may be obtained. Bureau of Mines research on the mining, preparation, and utilization of coal is directed toward developing and encouraging safer and more efficient mining practices and preparing and utilizing coals to the best advantage.

Jan 1, 1953

By Floyd R. Anderson

Noise control of existing pneumatic drills is difficult and runs into cost, performance and weight penalties. A need exists for a start-from-scratch approach for quiet pneumatic rock drills. The designs based on Leavell Principles which has been successfully used in demonstrating a quiet and vibration free paving breaker, is the concept chosen here. This report shows the feasibility of a quiet stoper for drilling roof bolt holes in coal mines. The work is directly applicable to pneumatic percussive rock drills. The report shows an oscillator based on patented Leavell concepts which results in a vibration free tool and noiseless exhaust. Dynamics of the oscilator is analyzed. Independant rotation of drill rod is provided by an air motor (screw expander) and flushing of cuttings is accomplished by an air ejector in a compact lower housing. The feasibility of no exhaust noise, low drill machine noise, and vibration free casing is discussed.

Jan 1, 1977

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By R. Karl Zipf

This report presents nearly all structural data available from explosion tests of 20-psi mine ventilation seals and concrete-block ventilation stoppings that were conducted by the National Institute for Occupational Safety and Health during 1997?2008. Although the seals tested were designed to meet the former federal 20-psi pressure design standard, the structural information contained herein on these seal tests will facilitate the analysis and design of coal mine seals that meet the new explosion pressure design criteria of 50 and 120 psi as set forth in the Mine Safety and Health Administration (MSHA)?s final rule on ?Sealing of Abandoned Areas.? The seal testing data are organized into six broad categories of seal structures based on the materials used and the construction method for those 20-psi seals: 1. Concretelike materials with steel reinforcement and reinforcement bar anchorage to rock 2. Pumpable cementitious materials of varying compressive strengths with no steel reinforcement and no hitching 3. Articulated structures such as solid-concrete-block seals and ventilation stoppings made of solid and hollow-core concrete blocks 4. Polymer and aggregate materials without hitching 5. Wood-crib-block seals with or without hitching 6. Articulated structures such as lightweight blocks with or without hitching This summary contains data on 52 different structures in the above categories?44 seals and 8 ventilation stoppings. The structural data sets include the applied loading on the tested seal represented by a pressure-time curve and, when available, the measured seal response represented by a displacement-time curve. The structural data sets enable the calibration and verification of numerical models of seal behavior at the 20-psi level, which may then facilitate future structural analyses of seal designs for the new 50- and 120-psi explosion pressure design criteria.

Aug 1, 2008

By Paul Hatmaker

This paper covers briefly the particular field of dolomite and magnesium limestone; certain uses of high-calcium limestone are mentioned only to show more clearly the limita¬ tions of the magnesian rocks. Such a comparison is helpful because magnesium carbonate is essential for some uses; for others it is immaterial; and for many its presence in an appreciable amount is objectionable. Magnesium carbonate, occurring as a rock resembling limestone or dolomite, is described in United States Bureau of Mines Information Circular 6437, Magnesite. Other com¬ pounds of magnesium are described in United States Bureau of Mines Information Circular 6406, Magnesium Compounds (Other Than Magnesite). Limestone, geologically, is a rock composed essentially of calcium carbonate; commercially, however, the term may include dolomite and magnesium limestone.

Sep 1, 1931

By S. C. Termes

The Bureau of Mines has used Fourier transform infrared spectroscopy (FT-1R) to study in situ reactions of aqueous solutions of potassium ethylxanthate with CU(II)-and Pb(II)-activated sphalerite plates, in which the plates were both the infrared-transparent windows and the reacting surfaces. A copper (I) ethylxanthate formed predominantly with Cu(II)-activated sphalerite, regardless of the activation time. The products formed on Pb(II)-activated sphalerite depended on the activation times; a short activation time (30 min) yielded a lead ethylxanthate-like product, but a long activation time (90 min) yielded a considerable amount of dixanthogen.

Jan 1, 1986

By R. V. Lundquist

This report describes results of tests on the desilication of solutions resulting from the leaching of lime-soda sinters. Desilication was accomplished by heating the solutions in an autoclave. A liquor relatively free of silica was obtained after 30 minutes of heating at 200 p.s.i.g. in the presence of lime. The addition of lime improved desilication, but the rate and efficiency of desilication was effected by the quality of lime used. The optimum quantity of lime for effective desilication was about 6 grams per liter. A lesser quantity gave poorer desilication, and a greater quantity increased the alumina loss without improving desilication. The alumina loss was approximately proportional to the lime added. A complex structure, called artificial noselite in this report, was the only silica bearing compound detected in the desilication precipitate. Other compounds present were Ca(OH)2 (calcium hydroxide), CaCO3 (calcium carbonate), and Ca [A1(OH)6]2 (hydrated tricalcium aluminate). Sodium carbonate in the leach liquor retarded the formation of the calcium aluminate; hence it decreased the alumina lost to the precipitate. The extraction of alumina from aluminum silicate materials by the limestone soda-sinter process has been investigated by the Bureau of Mines for many years. The process consists of the following major operations: Blending the aluminum silicate with limestone and soda ash in such proportions that dicalcium silicate and sodium aluminate are formed on sintering; leaching the sinter in a carbonated caustic solution to extract the soluble alumina; purifying the leach liquor by the precipitation of soluble silica (this precipitate is designated desilication precipitate in this paper); precipitating alumina trihydrate from the purified liquors by carbonating with carbon dioxide gas; and calcining the trihydrate to alumina. Commercial grades of

Jan 1, 1962

By Robert K. Koch

The reactions of alumina and alumina monohydrate with wet hydrogen fluoride gas were studied by the Federal Bureau of Mines to determine the feasibility of producing commercial-grade aluminum fluoride from offgases generated by pyrohydrolysis of siliceous fluorspars. The test results showed than an aluminum fluoride reactor operating at maximum efficiency could retain 96 percent of the fluorine contained in off-gases generated by pyrohydrolysis of siliceous fluorspar. The requirements are a reactor temperature of 200° C. and a reactor entrance gas containing 5 mole-percent hydrogen fluoride. Partial pressure equilibrium constants were determined for the reaction of alumina monohydrate and wet hydrogen fluoride gas from 200° to 350° C. and for the reaction of alumina and wet hydrogen fluoride gas from 350° to 700° C. Both reactions are reversible, and they proceed in directions that are dependent upon the temperature and the relative HF:H2O concentration. Logarithms of the equilibrium constants were used to plot the reaction isobars; these can be used to calculate the theoretical maximum efficiency of a reactor processing wet hydrogen fluoride gas between 200° and 700° C. The theoretical maximum efficiency decreases with increasing temperature.

Jan 1, 1961

By Ann G. Kim

Studies on the initiation and propagation of mine fires have dealt almost exclusively with coal. It has been assumed that the self-heating potential of carbonaceous shales and coal wastes is relatively low. However, in abandoned coal mines and waste banks, initiation and propagation of fires may be strongly dependent on the self-heating tendency of these materials. The purpose of this study was to compare the self-heating probability of carbonaceous shales and coal wastes to that of coals. This study utilized a modified differential thermal analysis method, in which the combustion furnace temperature was the reference to which the sample temperature was compared. Based on the distribution of the maximum temperature differential and the sample heating rate, a self-heating probability value (SHPV) was calculated that corresponded to observed self-heating behavior. In this study, several of the carbonaceous shales and one coal waste had relatively high SHPV. The SHPV did not correspond directly to heating values or to differences in sulfur concentration.

Jan 1, 2010

By Glenn C. Reed

The Sheep Creek iron deposits, Meagher County, Mont., were investigated by the Bureau of Mines in 1943 and 1944. Work undertaken included exploratory trenching, churn drilling, petrographic studies, and detailed beneficiation tests. It was determined that the Sheep Creek ores occur both as fissure filling and bedding replacements in thin-bedded shale and arenaceous limestones of the Algonkian Belt series. At least five stratigraphic horizons were found to be mineralized. Metallurgical studies indicate that the ores are not amenable to beneficiation by present-day low-cost methods. Details of geology, sampling, and beneficiation tests are presented in this report.

Jan 1, 1949

By L. A. Schutz

Personnel of the Bureau of Mines have conducted investigations in the principal asbestos mines and mills in the United States, to determine the concentration of airborne asbestos fibers in the workplace, and to establish the exposure of workers to such fibers. 'The surveys were conducted using the sampling and evaluation method recommended by the National Institute for Occupational Safety and Health. The method consists of collecting the air-borne sample on filters and, after appropriate sample preparation, counting the fibers utilizing phase contrast microscopy. The results of the investigation show that fiber concentrations are low in the asbestos mines but high in the asbestos mills, ranging well above 5 fibers/ml of air based on a count of fibers greater than 5 urn in length.

Jan 1, 1973

By Theodore Kootz

Manufacture of high-grade ferromanganese; as a rule; requires a low-phosphorus-manganese ore with 45 to 55 percent Mn, chiefly obtained in the Soviet Union, the British Dominions, and Brazil. Also, low-manganese ores have already been used for ferromanganese production, especially in North America .and Germany. During World War I, a process was developed in which a high-phosphorus ferromanganese or spiegeleisen was prepared in the blast furnace from law- or high-phosphorus manganiferous ores, then low-phosphorus manganese slag was prepared by refining under an acid slag, and this material was, worked into a low-phosphorus ferromanganese in the blast furnace.9/ Manufacture of useful manganese ores from a phosphorus-bearing spiegel with 12 to. 15 percent Mn, 4.5 percent C,, and 0.5 percent P by slagging in a refining furnace was reported by Joseph, Barrett, and Wood.10/ The spiegel was refined to 0.75 percent Mn, 3.4 percent C, and 0.45 percent P. Thereby, a slag with about 43 to 58 percent Mn and, about 10 percent Si02, was obtained. Hotter melts gave a smaller phosphorus content in the slag than cold melts. In addition, the phosphorus content of the slag varied with the manganese content of the intermediate metal.

Jan 1, 1952

By Laurence G. Trudell

A geologic framework for interpreting stratigraphic and geographic variations of the Green River Formation in the Piceance Creek Basin is developed from lithologic data accumulated by the Bureau of Mines from oil-shale coreholes. From detailed Bureau of Mines descriptions of samples from nine coreholes and supplementary lithologic data from seven additional sampled sections, three cross sections were constructed along lines transecting the basin. Plotted as lithologic columns with corresponding oil yields and resistivity logs, the sampled sections are correlated on a time-stratigraphic basis. Distribution and correlation of nahcolite and halite zones are shown, and the approximate base of leaching of these saline minerals is indicated. General lithologic characteristics of members and zones are discussed and interpreted. Large-scale lithologic logs illustrate the nine Bureau of Mines core descriptions, and the complete description of Bureau of Mines-Atomic Energy Commission Colorado Corehole No. 1 is included in an appendix. The time-correlated cross sections provide a necessary framework for understanding the depositional history of the Green River Formation and will facilitate evaluation of oil shale and other mineral resources in the Piceance Creek Basin.

Jan 1, 1970

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1[M] sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250°C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 2010

By J. G. Kirby

The total number of petroleum refineries in the United States decreased during 1951, while the total crude-oil charging capacity continued to increase. There were 350 refineries as of January 1, 1952, compared with 357 a year earlier, according to the annual Bureau of Mines capacity survey. A gain of 369,241 barrels in daily refinery crude through-put capacity during 1951 brings the total to 7,332,885 barrels daily. The capacity of the average refinery to process crude-oil was 20,951 barrels daily, an increase of 1,445 barrels daily over the previous year. Capacity added in the Texas Gulf district accounted for 36 percent of the total increase; the Indiana-Illinois-Kentucky district, 23 percent; the East Coast district, 19 percent; the Oklahoma-Kansas district, 12 percent; and the Texas Inland district, 11 percent. The California district was the only one reporting a decline in crude-oil refining capacity, the total being 14,200 barrels daily below the previous year. Reported as under construction January 1, 1952, was an additional crude-oil capacity of 282,680 barrels daily, an increase of 77 percent over the January 1, 1951, total of 160,100 barrels. The capacity now building is for the expansion of existing facilities, since no new plants had been begun as of the first of the year. Three or four companies have plans to build refineries in the Williston Basin area of North Dakota, but no definite locations or dates when construction will begin have been announced.

Jan 1, 1952

By H. F. Weaver

The 19th National First-Aid and Mine Rescue Contest was held in the Civic Center, Charleston, w. Va., on October 2, 3, and 4, 1961. The meet was sponsored by the Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other groups interested in safety. The Arrangements Committee, as authorized by the General Committee, made the necessary arrangements for conducting the 1961 contest. Members of the Arrangements Committee were: George Trevorrow (chairman), Bituminous Coal Operators' Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; Harry Gandy, Jr., National Coal Association; and James Westfield, Bureau of Mines.

Jan 1, 1962

By James Westfield

A brief resume follows of some recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors during their inspections of bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, following further consultations with representatives of management and mine workers, and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. The inspectors were active in making prompt investigations of hazardous mines that had been closed by order of the Coal Mines Administrator to determine if enough improvements had been made to allow the mines to reopen. Federal coal-mine inspectors also had temporary authority to close mines they found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1957