Search Documents

By Robert K. Koch

The reactions of alumina and alumina monohydrate with wet hydrogen fluoride gas were studied by the Federal Bureau of Mines to determine the feasibility of producing commercial-grade aluminum fluoride from offgases generated by pyrohydrolysis of siliceous fluorspars. The test results showed than an aluminum fluoride reactor operating at maximum efficiency could retain 96 percent of the fluorine contained in off-gases generated by pyrohydrolysis of siliceous fluorspar. The requirements are a reactor temperature of 200° C. and a reactor entrance gas containing 5 mole-percent hydrogen fluoride. Partial pressure equilibrium constants were determined for the reaction of alumina monohydrate and wet hydrogen fluoride gas from 200° to 350° C. and for the reaction of alumina and wet hydrogen fluoride gas from 350° to 700° C. Both reactions are reversible, and they proceed in directions that are dependent upon the temperature and the relative HF:H2O concentration. Logarithms of the equilibrium constants were used to plot the reaction isobars; these can be used to calculate the theoretical maximum efficiency of a reactor processing wet hydrogen fluoride gas between 200° and 700° C. The theoretical maximum efficiency decreases with increasing temperature.

Jan 1, 1961

By B. W. Gandrud

In 1927 Coghill showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and 'high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe. These ores slime readily during grinding, and in most instances the slimes are only slightly higher grade than the original ore. Not only do they carry a considerable percentage of the total iron in the ore, so that to reject them as tailings would result in prohibitively low extraction, but they are too fine to be amenable to ordinary methods of gravity concentration. In 1929 the Bureau of Mines published results showing that certain Alabama oolitic iron ores could be concentrated by classification and tabling after grinding, with rubber-covered rods. This selective grinding produced slimes of much higher grade than the original ore, and they were considered part of the final concentrate.

Jan 1, 1934

By Glenn C. Reed

The Sheep Creek iron deposits, Meagher County, Mont., were investigated by the Bureau of Mines in 1943 and 1944. Work undertaken included exploratory trenching, churn drilling, petrographic studies, and detailed beneficiation tests. It was determined that the Sheep Creek ores occur both as fissure filling and bedding replacements in thin-bedded shale and arenaceous limestones of the Algonkian Belt series. At least five stratigraphic horizons were found to be mineralized. Metallurgical studies indicate that the ores are not amenable to beneficiation by present-day low-cost methods. Details of geology, sampling, and beneficiation tests are presented in this report.

Jan 1, 1949

By David Schlain

A small alumina reduction cell with a graphite crucible and boron nitride liner was developed by the Bureau of Mines as the initial phase of a study of the reactions which occur in the reduction of alumina by the Hall-Heroult process. Operating conditions in the cell such as temperature, time, current density, electrolyte composition, and electrode materials may be varied easily. Aluminum was produced in the cell at a current efficiency of about 75 percent and a cell voltage of 2.7 volts. Although the data are not wholly conclusive, the operation of the cell did not appear to be greatly affected by large changes in temperature, electrode spacing, current density, and alumina concentration in the electrolyte.

Jan 1, 1963

By G. S. Scott. R. L. Grant

Ammonium nitrate (NH4NO3), a white crystalline chemical compound composed of 35 percent nitrogen, 60 percent oxygen, and 5 percent hydrogen, has again attracted attention, due largely to the recent catastrophe on April 16 and 17, 1947, at Texas City, Tex. The fire and subsequent explosion on the steamship Ocean Liberty, outside the harbor of Brest, France, on July 28, 1947, has fur- ther increased the interest in the properties of ammonium nitrate. As a result of the Texas City disaster, several laboratories have undertaken research to determine more certainly what causes ammonium nitrate to detonate and under what circumstances. This is not the first time that ammonium nitrate has been involved in a disaster, and its properties reviewed from the standpoint of safety. The disaster at Oppau, Germany, in 1921, which involved an equimolec- ular mixture of ammonium nitrate and ammonium sulfate, prompted an intensive study in Europe and in America. In the United States the properties of am- monium nitrate are now of especial concern because very large quantites are being manufactured and shipped in interstate commerce and abroad. Many an- monium nitrate factories, which were built during the war, will manufacture increasing amounts of this compound for use as a fertilizer. It is the purpose of this report to present a brief summary and biblio- graphy of the published experimental facts about the properties and behavior of ammonium nitrate. The reader is referred to original publications for greater details of the investigative work, and for theoretical discussions. This report also includes a survey of ammonium nitrate fertilizer of the type involved in the Texas City explosions. In the past, authorities have not always agreed on the degree of hazard involved in the manufacture and handling of ammonium nitrate, as the following quotations from the literature indicate: Munroe (82) quoted the following from Turner's Chemistry (a book pub- lished in 1835): "When this salt is exposed to fire, it liquefies, emits aqueous vapor, dries and detonates." Berthelot (14) in his book, Explosives and Their Power, 1983, wrote: "Ammonium nitrate from the point of view of its volatility, and cn account of many considerations, may be regarded as a typical explosive substance."

Jun 1, 1948

By Arthur V. Petty

The Bureau of Mines has researched the utilization of mining and pro-cessing wastes as raw materials for the production of glass-ceramic pipe. Characterization of various wastes as to occurrence and chemical composition is reported. A computer program was developed and used to identify waste materials and mixes that would result in glass melts from which glass-ceramics could be produced after cooling and subsequent heat treatments. The production of abrasion-resistant pipe from inexpensive and readily available domestic resources could offer an economical substitute for high-alloy steels containing the critical and strategic materials cobalt and chromium.

Jan 1, 1984

By Robert M. Becker

This investigation (in five parts) extends the theory of sample reliability from a sample consisting of a fixed number of items to a sample consisting of a fixed amount of items. Examples of a fixed amount of items per sample are samples consisting of a fixed weight or a fixed volume of unequal size particles. The extension of the theory is confirmed by experimental laboratory sampling using standard procedures. The probability distribution functions (the binomial, hypergeometric, multinomial, generalized hypergeometric, and those here called the compound binomial and compound multimomial functions) are developed from fundamentals. Their distributions are generalized to include some measured characteristic of the items. Infinite population moments are derived from moment-generating functions, and finite population moments are developed from corresponding infinite population moments using a newly defined mathematical operation. The first three experimental moments in laboratory sampling to given weights of particles are compared with the theoretical moments of their corresponding compound mult.inomial distributions. The agreement is striking. The study is divided into five parts. Part 1 deals with probability or random sampling to n items and with all sampling to n items per sample from some one probability distribution. This is the area of sampling covered by well-known theory. Accordingly, the procedures may be different but many of the results are well known.

Dec 1, 1964

By Laurence G. Trudell

A geologic framework for interpreting stratigraphic and geographic variations of the Green River Formation in the Piceance Creek Basin is developed from lithologic data accumulated by the Bureau of Mines from oil-shale coreholes. From detailed Bureau of Mines descriptions of samples from nine coreholes and supplementary lithologic data from seven additional sampled sections, three cross sections were constructed along lines transecting the basin. Plotted as lithologic columns with corresponding oil yields and resistivity logs, the sampled sections are correlated on a time-stratigraphic basis. Distribution and correlation of nahcolite and halite zones are shown, and the approximate base of leaching of these saline minerals is indicated. General lithologic characteristics of members and zones are discussed and interpreted. Large-scale lithologic logs illustrate the nine Bureau of Mines core descriptions, and the complete description of Bureau of Mines-Atomic Energy Commission Colorado Corehole No. 1 is included in an appendix. The time-correlated cross sections provide a necessary framework for understanding the depositional history of the Green River Formation and will facilitate evaluation of oil shale and other mineral resources in the Piceance Creek Basin.

Jan 1, 1970

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

By J. G. Kirby

The total number of petroleum refineries in the United States decreased during 1951, while the total crude-oil charging capacity continued to increase. There were 350 refineries as of January 1, 1952, compared with 357 a year earlier, according to the annual Bureau of Mines capacity survey. A gain of 369,241 barrels in daily refinery crude through-put capacity during 1951 brings the total to 7,332,885 barrels daily. The capacity of the average refinery to process crude-oil was 20,951 barrels daily, an increase of 1,445 barrels daily over the previous year. Capacity added in the Texas Gulf district accounted for 36 percent of the total increase; the Indiana-Illinois-Kentucky district, 23 percent; the East Coast district, 19 percent; the Oklahoma-Kansas district, 12 percent; and the Texas Inland district, 11 percent. The California district was the only one reporting a decline in crude-oil refining capacity, the total being 14,200 barrels daily below the previous year. Reported as under construction January 1, 1952, was an additional crude-oil capacity of 282,680 barrels daily, an increase of 77 percent over the January 1, 1951, total of 160,100 barrels. The capacity now building is for the expansion of existing facilities, since no new plants had been begun as of the first of the year. Three or four companies have plans to build refineries in the Williston Basin area of North Dakota, but no definite locations or dates when construction will begin have been announced.

Jan 1, 1952

By James Westfield

A brief resume follows of some recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors during their inspections of bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, following further consultations with representatives of management and mine workers, and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. The inspectors were active in making prompt investigations of hazardous mines that had been closed by order of the Coal Mines Administrator to determine if enough improvements had been made to allow the mines to reopen. Federal coal-mine inspectors also had temporary authority to close mines they found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1957

By John C. Gagliardi

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to ISO 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 2010

By M. Hayashi

The Bureau of Mines conducted laboratory studies on Idaho mudstones to examine techniques for extracting vanadium. Recovery of vanadium from low-grade sources could contribute to future vanadium production and reduce reliance on imports. An Idaho mudstone surface sample containing 0.30 pct V205 and an underground sample containing 0.21 pct V205 were used in the extraction tests. Leaching of the surface sample for 18 h at 800 C with the addition of up to 1,000 lb/ton H2S04 recovered 70 pct of the vanadium. How-ever, leaching of the underground sample under the same conditions re-covered only 47 pct. By adding 15 wt pct NaCl and roasting the samples at 7500 C for 2 h, followed by leaching with 800 lb/ton H2S04, vanadium extractions were increased to 78 pct from the surface sample and 83 pct from the underground sample. Water leaching of samples roasted at 7500 C for 4 h with a 25-wt-pct NaCI addition yielded about 60 pct of the vanadium from both surface and underground samples. Autoclave leaching at 2000 C for 3 h with 1,000 Ib/ton H2S04 extracted 97 pct of the vanadium from the surface sample and 86 pct from the underground sample. An exploratory solvent extraction investigation to purify and concentrate vanadium in the leach solution using several organic reagents was also conducted.

Jan 1, 1985

By Joseph Blake Smith

Coal resource data from published sources and company files were used by the Bureau of Mines to determine the location and extent of strippable coal reserves in Wyoming. Total strippable reserves of 23 billion tons were estimated in seven major coal areas. Seven large strip mining operations were active in 1969, and their production totaled 45 million tons of coal. Cutoffs used to define strippable reserves were (1) minimum coalbed thicknesses of 5 feet; (2) overburden-to-coal ratios of less than 10 cubic yards of over- burden per ton of coal; and (3) total overburden thicknesses of less than 120 feet, except where reserves occur in multiple beds or a single thick bed. Tertiary rocks along margins of the Powder River basin contain most of the strippable coal reserves in Wyoming. The Wyodak beds, ranging in combined thickness from 30 to 1.30 feet, crop out on the east flank of the basin and contain an estimated 19 billion tons of strippable subbituminous C-rank coals under less than 200 feet of overburden. Partings between these beds total less than 60 feet. The 100- to 200-foot-thick. Healy bed on the western flank of the basin and the 35-foot-thick School and 20-foot-thick Badger beds on the south also contain large strippable reserves. Elsewhere in Wyoming, strippable reserves. Elsewhere in Wyoming, strippable deposits are subbituminous coal of Late Cretaceous and Tertiary ages, mostly in the Hanna and Great Divide basins in the south-central portion of the State and in the Kemmerer-Hamms Fork region in the southwestern corner.

Jan 1, 1972

By H. F. Weaver

The 19th National First-Aid and Mine Rescue Contest was held in the Civic Center, Charleston, w. Va., on October 2, 3, and 4, 1961. The meet was sponsored by the Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other groups interested in safety. The Arrangements Committee, as authorized by the General Committee, made the necessary arrangements for conducting the 1961 contest. Members of the Arrangements Committee were: George Trevorrow (chairman), Bituminous Coal Operators' Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; Harry Gandy, Jr., National Coal Association; and James Westfield, Bureau of Mines.

Jan 1, 1962

By Cloyd M. Smith

Progressive mine management is placing increased emphasis on improved ventilation as a contribution to better safety , health , and productivity of miners . Management is on the alert for means of bettering the working environment by increasing the flow of air and distributing it more effectively to the working places , having in mind the necessity of avoiding exorbitant ventilation costs . A basic need in planning betterments of this kind is knowledge of existing rates of flow and air pressures , infCoorrmmaattiicon that is supplied through ventilation surveys . Some companies make partial surveys from time to time , but few make complete surveys on a routine basis . This report describes the practice of a large British anthracite -mining company , which operates 24 collieries in South Wales , in carrying out a routine program of ventilation surveying . Ventilation characteristics and climatic conditions in the working places of its collieries are determined at frequent intervals with a view to increasing the effectiveness of ventilation and protecting the health of workers . It is thought that many of the points of the procedure used in making the surveys and in compiling and reporting the results will be applicable to American practice and that a discussion of the program may be helpful to colliery managers who are planning similar work .

Oct 1, 1949

By E. O. RHODES

Germany's' wartime coal-tar industry had two main branches, which can best be considered individually because their raw materials, operations, and distributions were almost completely separated. One branch, old and well-established, was concerned almost entirely with processing coal tar produced by the high-temperature carbonization of caking bituminous coal. Carbonization was effected principally in byproduct- coke ovens and to less extent in vertical, horizontal, and inclined retorts. The high-temperature tar was all processed in tar-distilling plants that handled high-temperature tar almost exclusively.

Sep 1, 1947

By H .. B. HUMPHREY, F. E. Cash

Sixty-one fatal accidents were reported in the mines of Alabama during 1930. This number is a decrease of 15 per cent as compared with 1929; however, production was 13 per cent and the man-hours worked were 16 per cent less than in the previous year. There were 21,731 men employed inside and 3,386 outside. Table 1 gives the comparative rates per million tons and per million man-hours for the United States and for Alabama for 1929 and 1930. These rates are based on figures published by the State and by the United States Bureau of Mines, with preliminary figures for 1930. (These sources of data are used throughout this paper.)

Oct 1, 1931

By Michael J. Sapko, Kenneth L. Cashdollar

In This Chapter [Methane ignition as initiation source for much larger secondary coal dust explosions Rock dusting requirements to prevent coal dust explosions Dangers of hybrid mixtures of methane and coal dust] Although methane explosions are dangerous, those that involve coal dust are even more so. If exploding methane disperses and ignites the coal dust that has accumulated on the mine ribs and floor, the burning coal dust immeasurably increases the strength of the explosion. Such methane-dust explosions are prevented by inerting the coal dust in a way that prevents the exploding methane from igniting it. This chapter discusses the dust hazard and how it is pre-vented in U.S. coal mines. METHANE IGNITION AS INITIATION SOURCE FOR MUCH LARGER SECONDARY COAL DUST EXPLOSIONS The typical scenario for coal mine explosions starts with the ignition of a flammable methane-air atmosphere near the face. The turbulent winds from the primary methane explosion then disperse the coal dust. If there is insufficient rock dust (usually limestone), a secondary coal dust explosion then propagates throughout large sections of the mine. These scenarios have been studied extensively at the Bruceton Experimental Mine (BEM) and the Lake Lynn Experimental Mine (LLEM) of the NIOSH Pittsburgh Research Laboratory. The minimum quantity of methane required to initiate a coal dust explosion was studied in 1930 in the BEM [Rice et al. 1933; Nagy 1981] and then later in the LLEM, whose cross-sectional area (130 ft2) is over twice that of the BEM [Sapko et al. 1987a]. Studies conducted in the BEM closely simulated conditions that existed in operating mines in the early 20th century. The later tests in the 20-ft-wide entries of the LLEM simulated the geometries of modern mines with advanced roof support technology. The data from the BEM tests show that 13 ft3 was the minimum quantity of methane at the face that, when ignited, would disperse and ignite coal dust. In the BEM, this amount of methane was mixed with air to form a total flammable volume of about 140 ft3 of a 9% methane-in-air mix-ture. In the wider entries of the LLEM, about 37 ft3 of methane was required to disperse pure coal dust and start a self-sustained coal dust explosion. This amount of methane was mixed with

Jan 6, 2006

By Robert C. Ellman

The Bureau of Mines investigated the factors that cause agglomeration of lignite by freezing during winter shipment and sought methods to avoid it. Tests showed that lignite may be freezeproofed by removal of the relatively small quantity of moisture involved in forming the frost crystals which cement particles together, or by controlling the crystal characteristics. Adding dried lignite fines proved to be an effective and superior freezeproofing method. Commercial adoption of this method has been successful.

Jan 1, 1965