Search Documents

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Nicholas County, W. Va. It is one in a series describing coals suitable for producing metallurgical coke, either as mined or after beneficiation. Almost 5 million tons of coal were produced in Nicholas County, W. Va., in 1960, of which over 2.6 million tons were cleaned in eight preparation plants. It has been estimated that over 6 billion tons remained in the county as of December 31, 1960, in beds 12 inches and more thick.

Jan 1, 1962

By Edward L. McHugh, Stanley M. Miller, Jeffrey K. Whyatt

The point estimation method can be applied to the safety factor (SF) equation for any specified rock slope failure mode (such as plane shear, step path, or wedge) to obtain reliable estimates of the mean and standard deviation of the SF probability distribution. A gamma probability density function is recommended for modeling this probability distribution, because it allows only for positive values and is flexible enough to provide symmetrical shapes and right-skewed, exponential-type shapes for the SF distribution. The mean and standard deviation define this distribution, which then can be integrated numerically from 0 to 1 to obtain the probability of sliding, PS (portion of the SF distribution where SF < 1.0). The overall probability of failure, PF, for the potential slope failure mass is the joint probability that the rock discontinuities are long enough to allow kinematic failure (PL) and that sliding occurs along the rock discontinuities (PS); that is, PF = PSPL. This method for estimating the probability of sliding is extremely efficient computationally, and thus, expedites slope stability simulation routines used by NIOSH software to stochastically describe rock slope behavior and assist the engineer in designing catch benches for large rock slopes. Enhanced bench design translates into increased operational efficiency and safer working conditions in open pit mines and quarries.

The Waukon iron deposit comprises about 210 acres situated 2-1/2 miles north of Waukon, in Allamakee County, northeastern Iowa. The deposits have been exploited intermittently since 1899 and have produced about 67,000 tons of concentrated iron ore. From January to May 1943, the Bureau of Mines investigated the deposit to determine the extent of the ore-bearing material and its amenability to concentration, Seventy-one test pits were sunk. Those that indicated are of a grade high enough to warrant concentration tests were sampled. Average grade of ore was indicated to be 37.02 percent iron and 27.78 percent silica on a dry basis. Beneficiation tests indicated that the percentage of recovery might be relatively low.

Jan 1, 1949

By H. C. Carpenter

Data are presented comparing results obtained with 17 different catalysts in hydrogenating crude shale oil to gasoline in single-pass operation. A method is described for predicting the maximum yield of gasoline obtainable at constant pressure for each catalyst from results of a limited number of experiments at different temperatures. Operating variables have considerable influence on yields and properties of products. With most of the catalysts, at operating temperatures below 890° F. liquid yield exceeded 100 volume-percent. Above this temperature the volume of liquid product decreased rapidly. Maximum gasoline production in most instances was achieved at a temperature higher than that at which the maximum volume of liquid product was produced.

Jan 1, 1959

By James R. Boyle

The value of Alabama&apos;s nonfuel mineral production in 1980 was $328.6 million, a decrease of $7.8 million from 1979. Cement, crushed stone, lime, clays, and sand and gravel continued as the major commodities produced. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, ferroalloys, kaolin, and oyster shell; fourth in dimension marble, masonry cement, and bentonite; and fifth in fire clay and lime. Alabama ranked in the top 20 States in total value of non-metallic minerals produced. Adverse economic conditions in the construction and metals industries impacted on the minerals industry in Alabama. Mineral producers supplying raw or finished materials to these industries experienced periodic reductions in sales during the year. Unit price increases did not keep up with inflation.

Jan 1, 1982

By Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep sandstone in the Elk Basin field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes of gas in solution, saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep reservoir of the Elk Basin field has unusually varying physical characteristics, such as a saturation pressure of 1,250 pounds per square inch absolute and 490 cubic feet of gas in solution in a barrel of oil at the crest of the structure, and a saturation pressure of 530 pounds per square inch absolute and 134 cubic feet of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the 6a r; in solution in the oil varies from 18 percent for oil on the crest to 5 percent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of oil in the structure. Many geologists and petroleum engineers have considered all the oil in a petroleum reservoir to have uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas. That such is not always so is borne out by the results of the study made by the writers.

Jan 1, 1951

By Victor Kalcevic

A gas-flow retort for thermal processing of oil shale to recover shale oil was developed by the Bureau of Mines at its Oil-Shale Demonstration Plant, Rifle, Colo., from 1948 to 1952. The retort is a crossflow gas-to-broken-solids heat exchanger. The heating medium is the gas produced in the shale retorting process. The gas is heated in specially designed stoves outside the retort and recycled to the retort. Oil shale from the Mahogany ledge section of the Green River formation in northwestern Colorado was the material processed. Indicated maximum oil recoveries for 20-to 25-gallon-per-ton shale in a l2-inch-thick shale bed and a 20-inch bed are 96 and 91 weight-percent of Fischer assay, respectively. Heat requirements for maximum recovery are 600 to 750 B.t.u. per pound of shale. Properties of the recovered shale oil are affected slightly by shale-bed thickness and extent of retorting. Oil recovery from oil shales assaying over 30 gallons per ton is lower than that from leaner shales.

Jan 1, 1959

By Joseph Coffman

There are 14 operations that supply 97% of the Market Economy Country (MEC) manganese and contain nearly all of its resources. Six mines account for about 70% of the production and 85% of the resources; there are no known resources that are economically close to those that are currently being mined. Costs (January 1989 dollars) of producing manganese concentrates from the operations evaluated are estimated to range from $ 0.96 to $ 1.86 per long ton unit (ltu or 22.4 lb) of contained manganese. Total MEC demonstrated resources evaluated amount to about 1.2 billion tons of in situ ore containing 474 million tons of manganese. Identified resources amount to about 1.8 billion tons of in situ material. Key results of the study indicate the following: 1. The MEC supply of manganese will be from the currently mined resources well into the next century. 2. Centrally Planned Economy Countries (CPEC&apos;s) will be increasingly dependent on MEC manganese ore and concentrate in the future. 3. At the 1976 to 1987 demand increase rate, total MEC resource needed through the year 2000 would be about 282 million tons of in situ material. 4. Transportation and infrastructure support will continue to be major elements of production costs.

Jan 1, 1992

By John Soule

The Torpedo copper mine in the Organ Mining, District, Dona Ana County, N. Mex., was discovered in 1899, and production of copper from oxidized-ore deposits was begun in 1900. Production continued through 1907, but operations were only intermittent frown 1907 through 1921. The production of copper during these periods amounted to about 3,500,000 pounds. Reserves primary sulfide copper ore were believed to occur below the old workings, and after a detailed examination of accessible workings and a study of drilling records of several private companies by an engineer of the Bureau of Mines, a development program of diamond core drilling was initiated. This investigation was started October 3, 1949; and completed April 30, 1950. Four holes totaling 2,122.3 feet wore diamond-drilled, and 70 samples were analyzed. All drilling was done with a Government-owned hydraulic-feet drill having special rods and core barrels to increase the recovery of core in critical zones. This report describes the location, history, ore deposits, and factual data obtained by the Bureau of Mines from the drilling.

Jan 1, 1951

By C. B. Barmore, B. W. Gandrud, B. M. Bird

"The Bradford mine of the Alabama By-Products Corporation is located in the Warrior coal field of Alabama, in the northern part of Jefferson County, about 25 miles north of Birmingham. The coal mined from the Black Creek bed at this point is not considered to be ideal for coke making by itself but because of its exceptionally low ash content is mixed with the higher-ash coking coals from other beds of the district to control the ash content of coking mixtures. Further reasons for using this coal only as a diluent of the higher-ash opals are that the thinness of the bed renders the production costs relatively high and the reserves are somewhat limited.This paper, which is the fourth of a series on the washability of Alabama coals, Like its predecessors dealing with the Mary Lee beds and the Clark bed,6 contains screen-sizing and float-and-sink tests of a representative sample of the raw coal, and flakiness tests showing the proportions of flaky particles in certain selected sizes. However, inasmuch as the float-and-sink tests of the coarse sizes showed excellent liberation of coal from impurities, crushing tests have not been considered necessary.The data on which this report is based have been obtained in connection with an exhaustive study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. As the work progresses other papers will follow containing further data on Alabama coals and giving results obtained in preparing these coals by various methods."

Apr 1, 1931

By G. W. Jones

As a part of it investigations pertaining to the promotion of safety, the Bureau of Mines is investigating various means, useful for the elimination or mitigation of the explosion hazards of combustible gases encountered in mining and industry. Information has been obtained and a procedure developed whereby the explocibility of many complex, gaseous, combustible atmospheres may be calculated in a simple manner without the necessity of performing laborious laboratory experiments. In a previous publication4/ data were given and a method described whereby the limits of inflammability of gaseous mixtures, including methane, hydrogen, carbon monoxide, nitrogen, carbon dioxide, and oxygen, could be determined by calculation. The information published in that report enables one to calculate the limits of inflammability of such gases as are liberated by mine fires, gases from explosives, automobile exhaust ran, uses present after mine explosions, blast-furnace gas, and other gases containing part of or all of the above-listed constituents.

Jan 1, 1938

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By Lito C. Mejia

Diesel-powered equipment operating in a gassy underground mine could conceivably ingest a methane-air mixture from the mine atmosphere that could cause the diesel engine to overspeed, or exceed its rated speed. Engine overspeed, particularly if extreme (engine runaway), could result in personal injury, a possible mine explosion, and/or catastrophic engine failure. In this report, the Bureau of Mines reviews the literature on the potential hazards of methane-induced diesel engine overspeed. Also included are the Bureau&apos;s findings from consultations with representatives of the diesel engine industry to determine the specific engine behavior that could he expected under the overspeed condition. The report summarizes data on mine accidents involving methane, discusses results of tests on the compression ignition of methane in diesel engines, and examines fuel governors and intake-air-cutoff devices, two kinds of devices used to prevent overspeed. Analysis of the information gathered suggests that the conditions necessary to cause a diesel engine to overspeed uncontrollably are not likely to occur, particularly if the engine is equipped with flame-proofing devices. The available literature and lack of actual overspeed case histories suggest that the safety devices currently in use are sufficient to prevent diesel engine overspeed.

Jan 1, 1984

By Clark P. Mangelsdorf

The report consists of two parts. In Part I is a state-of the-act study of roof truss technology as of January 1979. Included are a history of the truss concept, a review of analysis techniques, a record of hardware available and equipment used in its installation and numerous examples of user experience. Part II is concerned with a study of the role of friction in the behavior of a roof truss. The appendices include laboratory tests by the author.

Jan 1, 1979

By T. H. Dubaniewicz

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 2010

By Ren G. Dong, John Z. Wu, Daniel E. Welcome, Kristine Krajnak

Although the exact mechanisms underlying vibration white finger (VWF) are not clear, it has been speculated that VWF is associated with variations of the blood flow patterns due to the physical damage and/or degeneration in neural and vascular tissue caused by vibration loading [1]. Excessive dynamic deformation of the soft tissues in the fingertip under vibration loading is believed to induce multiple occupation-related hand/finger disorders. However, the in vivo distributions of the dynamic stress/strain of the tissues in the fingertip under vibration conditions have not been studied because they cannot be measured experimentally to date. The goal of this study is to analyze, theoretically, the location and frequency-dependent dynamic deformation of the soft tissue in the fingertip during vibration exposures. [ ] Methods The fingertip considered in the model is the distal phalanx, the portion from the distal end of the fingertip to the distal interphalangeal (DIP) joint articulation (Fig. 1). The external shape of the fingertip was determined using a smooth mathematical surface fitting to the observed fingertip shapes. The fingertip surface was then scaled to the dimensions of a typical male index finger: length 25 mm, width 20 mm, and height 18 mm. The fingertip was approximated to be symmetric, such that only a half of the fingertip was considered in the FE modeling. The fingertip was assumed to be composed of outer and inner skin layers, subcutaneous tissue, bone, and nail. The soft tissues (inner skin layer and subcutaneous tissues) were assumed to be nonlinearly elastic and viscoelastic, while the bone, nail, and outer skin layer were considered as linearly elastic. The simulations were conducted using a displacement-controlled protocol in two stages. First, the fingertip was statically pre-compressed. The contact plate was first displaced towards the finger to achieve a predetermined value of tissue deformation (i.e., 0.5, 1.0, 1.5, and 2.0 mm). Second, the steady-state dynamics responses of the fingertip were analyzed using a linear perturbation procedure. The fingertip was subjected to a continuous harmonic excitation (magnitude 0.5 mm) from the contact interface. The dynamic analysis was performed in a frequency domain ranging from 16 to 2000 Hz. The frequency-dependent distributions of the vibration magnitude and dynamic strain magnitudes in the soft tissues are investigated. Results Typical simulation results for the frequency-dependent distributions of the vibration magnitude in the soft tissues are shown in Fig. 2 (figures show the results with a pre-compression of 2.0 mm). The vibration magnitude at the contact surface is 0.5 mm (specified) for all frequencies, while the vibration magnitudes in the soft tissues are location- and frequency-dependent. It is clear that the fingertip has a major resonance around 125 Hz, at which the vibration magnitudes in the soft tissues are over four times greater than that of the contact plate (0.5 mm). It is interesting to observe that, at this resonant frequency (125 Hz), the soft tissues at the tip has the maximal vibration magnitude while the regions near the contact

Jan 6, 2006

By E. Chin

The countries of Asia and the Pacific have large resources of diverse minerals. Australia and China have extensive mineralization that are commercially being exploited. The major minerals in Australia with known reserves adequate for both domestic demand and export markets include bauxite, clays, copper, diamond, gold, iron ore, lead, manganese, mineral sands (titanium minerals), nickel, salt, silver, tin, uranium, and zinc. China is the world leader in proven reserves of antimony, barite, magnesite, molybdenum, rare earths, titanium (ilmenite), tungsten, and vanadium. It also has about 55 billion tons of iron ore, albeit with an average grade of only 30 % to 35 % elemental iron content. With the exception of chromium and copper, China has significant resources of a wide array of minerals and metals, based on its production and/or export capability for these commodities. Additionally, India has significant resources of bauxite and mineral sands; Indonesia, bauxite, copper, nickel, and tin; Malaysia, tin and associated titanium; Mongolia, copper, fluorspar, and lead-zinc; New Caledonia, nickel; New Zealand, gold and iron sand; North Korea, magnesite; Papua New Guinea, copper, gold and mineral sands; Philippines, copper, chromite, and gold; and Sri Lanka, gemstones. Moreover, there appears to be extensive mineralization III Burma (Myanmar), Cambodia, Laos, Thailand, and Vietnam, but they have yet to be definitively delineated.

Jan 1, 1994

By Raja V. Ramani

The potential usefulness of reclaimed surface-mined land has received much attention recently. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U.S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, the Chinook Mine-West Field, located in western Indiana, has been studied. The Chinook Mine is presently operated by AMAX Coal Company and has been in continuous operation since 1928 under various ownership. The status of current reclamation and land use planning was reviewed. In addition, site planning principles were applied to the active mine area. This application included formation of a data base and development of postmining land use plan alternatives. Key factors affecting site potential realization for midwestern area mines have been identified along with suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By C. A. Taylor, C. E. Munroe

"In blasting the explosion of the high explosives charge is initiated by means of a detonator. Consequently the successful operation of the whole system is, ab initio dependent upon the suitability and efficiency of the detonator used. A considerable number of methods for testing the efficiency of detonators have been devised. In a previous publication*** of the Bureau of Mines many of these were discussed after having been classified as direct and indirect methods.In 1910, W. O, Snelling, then explosives chemist of the Bureau, devised a direct method which depends on the extent to which a hard brittle material of uniform granulation, such as quartz sand, is pulverized by the explosion of the detonator when imbedded in it, and, as a container in which to carry out the tests, he devised the vessel known as the Bureau of Mines sand-test bomb No. 1. A brief mention of his work was made in a paper presented to the Engineers' Society of Western Pennsylvania.****Later Storm and Cope made a very extended investigation of this method using sand-test bomb No, 1. Their paper***** contains a detailed, illustrated, description of sand-test bomb No. 1, with precise specifications of the sand and a minute account of the technique followed, together with a discussion of the data they obtained from the tests in this bomb of 112 detonators representing each of the grades from We, 3 to No. 10, inclusive. The average of results obtained by them are set forth in the following table."

Dec 1, 1923

By William S. Roberts

As part of the Bureau of Mines critical and strategic minerals program in Alaska, 34 high-purity chromian spinel samples were analyzed for trace and major element geochemistry and mineralogy. The samples were analyzed by X-ray diffraction, X-ray fluorescence, and chemical techniques. Systematic differences in chemistry are evident when samples collected from the Chugach Mountains and their related extension are compared with chromian spinel samples collected from interior Alaska. Compared with the Chugach samples, the interior Alaska samples have higher average amounts of A1203, Fe203, Ti02, and NiO, have lower average amounts of FeO and Cr203, and exhibit greater dispersion in values. Considerable mineralogical variability of chromian spinel exists between and within individual Alaskan chromite-bearing ultramafic complexes. Of 34 samples analyzed, 25 samples are magnesiochromite, 5 are chromite, 3 are spinel, and 1 is hercynite. As a group the interior Alaska samples have a smaller average unit cell dimension than the Chugach group of samples. The chemical and mineralogical differences between the two groups of samples can be attributed to different genetic histories and may have implications for locating chromian spinel deposits amenable to standard beneficiating techniques.

Jan 1, 1985