Search Documents

By Edward A. McClatchie

A methane monitor that complies with 30CFR75.313 has been designed and fabricated using a novel pressure modulated infrared absorption technique. The methane monitor met or exceeded in performance all of its target specifications. The monitor was operated continuously during production mining for the entire duration (45 days) of the in-mine test; no failures occurred during the test. The monitor was regularly checked with calibration gas and no shifts in calibration were found during the in-mine test. Operating principles, performance data and electrical schematics are included in the report.

Jan 1, 1976

By F. P. Haver

A method to recover copper and elemental sulfur from chalcopyrite concen¬trate, using a ferric chloride leach, CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S, was reported by the Federal Bureau of Mines in 1971 (Report of Investigations 7474). Since that time, additional work has been done to improve certain steps in the procedure; that is, the recovery of sulfur from the leach residue, the recovery of copper and iron from the leach solution, and the regeneration of the leach solution. It was determined that over 99 pct of the elemental sulfur in the leach residue could be extracted at ambient temperature with an ammonium sulfide solution. Heating the pregnant solution precipitated crystals of rhombic sulfur (99.5 pct purity) and liberated ammonia and hydrogen sulfide for recycle. Copper with a purity in excess of 99 pct was obtained from the leach solution by electrolysis, using a diaphragm cell, with an energy requirement of less than 0.7 kW-hr/lb. Metal was deposited as a weakly adherent powder that could be easily dislodged from the cathode and withdrawn continuously from the cell in the form of a slurry. During electrolysis, part of the Fe(II) was oxidized to Fe (III) at the anode so there was no chlorine evolution. The leach solution was regenerated by direct oxidation of the spent electrolyte with air or oxygen in a turboaerator at 80° C. This precipitated the iron dissolved during leaching in an easily filterable form, Fe203.xH20, and converted the remaining Fe(II) to Fe(III).

Jan 1, 1975

By L. F. Heising

Ten composite samples of Mesabi Range nonmagnetic taconite from the Hibbing, Minn., area were evaluated by flotation and by reduction roasting-magnetic separation to determine their potential as a future source of iron are. Only one of the composites yielded concentrates that could be considered marketable, using as a criterion a 10-to-1 iron-to-silica ratio. Cursory petrographic examinations of all 10 composited samples and a detailed mineralogical study on 1 sample suggest that unfavorable mineralogical associations between iron and gangue minerals are responsible for their poor beneficiation characteristics.

Jan 1, 1967

By R. Hogg, S. Chander

"An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example in development of new processes, plant and process design, plant control, problem solving, etc. IntroductionThe behavior of particulate systems, in mineral processing and other applications, is primarily affected by the physical characteristics (size, shape, surface area, pore structure) of the particles and the nature of the different solid-fluid interfaces present. Mineral processing operations in general are either designed to modify and/or control physical and interfacial properties (grinding, classification, agglomeration, etc.) or are strongly influenced by them (flotation, flocculation, solid/liquid separation, etc.). Characterization of physical and interfacial properties should be an integral part of the development of new processes, plant and process design, and routine plant operation.Our purpose in preparing this article has been to present an overview of the current status of characterization, to point out areas of weakness, and to discuss the reliability and limitations of the various techniques, procedures, and instrumentation available. For more detailed discussion of methods, etc., the reader is referred to standard references.Sampling particulate solids.Sampling is a critical factor in any procedure for characterizing particulate materials — the reliability of characterization data is ultimately limited by the extent to which the sample used was truly represen¬tative of the population from which it was taken.Sampling from particulate solids involves two basic problems: (1) the selection of a random', unbiased sample and (2) choice of the appropriate sample size.The problem of sample selection involves the design of a sample collection procedure that ensures that every kind of particle in the population has the proper chance of being included in the sample without bias. Specific procedures such as the well-known cone-and-quarter technique have been developed and are discussed at length in the literature on particle characterization (Allen, 1981: Herdan, 1960: Gy, 1982)."

Jan 1, 1989

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

By Thomas M. Barczak

The 1990s brought an unprecedented increase in the development of innovative technologies to provide more effective and easier-to-install roof support in underground mines. To facilitate the application of these technologies in improving mine safety, the National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a Windows-based software program that provides mine operators with a simple and practical tool to make engineering decisions about the selection and placement of these various roof support technologies. The program includes a complete database of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. A support design criterion in the form of the required support load density at a specified convergence can be established from four options: (1) a database of measured ground reaction obtained from various mines or ground behavior information input by the user,(2) load requirements based on a detached roof block or rock failure height, (3) criteria based on the current roof support system, and/or (4) arbitrary criteria set by the user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user-specified support installation. In addition to these performance measures, STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made, including a graphical analysis of relevant support parameters. This paper describes STOP and its application to optimizing standing secondary roof support systems.

Jan 10, 2000

By J. A. Woolf, E. S. Leaver, N. K. Karchmer

"In the cyanidation of silver ore, the need of oxygen is well recognized. Various methods have been introduced for supplying the oxygen. In usual practice, air is the source of oxygen and the methods of application are mechanical.This article gives the results of touts made to show the rate of dissolution of silver from each of the common silver minerals in cyanide solution, under conditions similar to those used in the practical recovery of silver from its ores. The effect of oxygen in aiding the dissolution of the silver from each mineral is also shown by a comparison of the methods of supplying the oxygen. Oxidation by preliminary roasting (500°C.) of each mineral sample gives the maximum extraction of the silver by treatment with cyanide.Each silver mineral5 used in these experiments was as pure as could be obtained from the mineral dealer. In their natural occurrence, silver minerals are not usually free from mineral impurities. They are usually closely associated with other minerals often forming, a complex mixture. The form of crystallization, the proportions, and properties of the diluent that incases or has been dispersed with the silver mineral may decidedly affect the dissolution rate of the silver from each mineral. While the following results should aid in the cyanidation of silver ores, each ore should be studied from the basis of the form and condition of the silver that is to be recovered.All the tests reported in this article were made on synthetic samples, prepared by mixing the particular silver mineral with clean sea sand. Each mineral was ground in an agate mortar to pass 100-mesh before mixing with the sand which had previously been ground in a porcelain pebble mill to 100-mesh. Such proportions of each mineral and the sand were used as to give a head assay of approximately 20 ounces of silver per ton to the synthetic sample.Agitation was carried on in stoppered bottles approximately one-third full of pulp, method apparently supplied all the atmospheric oxygen that would be taken up by the solution under usual conditions, because tests conducted in open bottles did not show increased recovery,"

Jan 1, 1931

By John R. Benham

In 1987, at the request of the Bureau of Land Management~ the U.S. Bureau of Mines studied 7,600 and 3,000 acres, respectively, of the Slocum Creek (OR-003-075) and Upper Leslie Gulch (OR-003-074) Wilderness Study Areas in order to evaluate their mineral resources. They are located in Malheur County, OR, about 25 mi northwest of Jordan Valley. Both areas have an occurrence of stone (welded tuff) covering about 3,000 acres which is suitable for construction purposes including road metal, ballast, and road fill. However, similiar deposits are more accessible and closer to markets.

Jan 1, 1988

By M. M. Wong, J. E. Klosterman

Scrap beryllium chips ( nominally 96 to 97 percent Be ) were electrore fined in a prototype cell with 408 lb of electrolyte composed of 52.4 mole - percent LiCl , 36.3 mole - percent KC1 , and 11.3 mole - percent BeCl2 . The cell temperature was 500 ° C. In a typical 10-3 /4 - hour deposition cycle , 0.415 pound of metal was produced ; the metal contained impurities in parts per million as follows : C , 700 ; 0 , 610 ; Al , 34 ; Ca , 32 ; Cu , 20 ; Fe , 25 ; Mg , 9 ; and Mn , 23 . Operation of the prototype cell for 2 years demonstrated that adapting the electrorefining process to an enlarged scale of operation presented few difficulties in mechanical functions , maintenance of optimum operating conditions , and control of product purity . After the spent anode feed was leached in a 5 - percent nitric acid solution and the fine - sized particles were removed , it was recycled in some tests . The metal produced was somewhat higher in impurities than metal from the fresh scrap chips .

Jan 1, 1964

By Robert Stefanko

Test procedures for evaluating underground coal mine trailing cable splices are formulated. The tests are utilized to evaluate several trailing cable splices. The laboratory results are compared with actual field observations and experience. The results are utilized to define quantitatively the generalized terms of the 1969 Health and Safety Act. Recommended specifications and procedures for testing by MESA Department of Approval and Testing personnel are included. Failure points in splices are detailed and presented for use by a MESA training program and manufacturers attempting to improve product quality.

Jan 1, 1974

By K. C. Vincent

In the course of, investigation of domestic manganese-mineral occurrences, examining engineers of the Bureau of Mines collected 2-ton lots of ore from properties in the Cleveland-district, Idaho. As only one of the ores was high enough in grade for direct marketing to-producers of ferromanganese, ore-dressing concentration methods were investigated to determine their amenability to treatment. High-grade ore. (38.7 percent Mn) from the Idaho Manganese Mining Co. was taken from a replacement deposit in limestone consisting of several horizontal beds 1 to 5 feet thick, about 1 mile northeast of Cleveland. The manganese minerals occur as an intimate intergrowth of manganese oxides, containing minor amounts of limonite, ?quartz, and calcite as rather fine inclusions. However, the major contaminants are claylike products of rock decomposition, which can be eliminated by thorough washing of the ore at relatively coarse sizes. The Hot Spot property is 1 mile south of Cleveland. The ore occurs as a replacement deposit of medium-grade- ore in limestone, .The sample taken by the Bureau of Mines assayed 26.0 percent Mn. The manganese minerals consist of nodules, principally pyrolusite with some psilomelane and manganite embedded in wad.' The low-grade wad, containing manganese and siliceous minerals in intimate association, was easily rejected by washing.

Jan 1, 1952

By E. J. Murphy, John C. Holtz

"INTRODUCTION Toxic gases in the products from the detonation of explosives are one of the hazards in blasting underground. Investigations by the Bureau of Mines 4/5/ have shown that the oxygen balance of the explosive is an important factor in the control of toxic gases. This balance is considered in determining the composition of modern metal-mining explosives for blasting underground, and application of the concept has reduced the volume of toxic gases generated.The chemical nature of the material being blasted also influences the composition of the toxic gases produced. Under some conditions of blasting in massive pryrite, unsafe concentrations of sulfur dioxide and hydrogen sulfide have been found.Experiments with the O-J apparatus 8/ have shown that there is an increase in the volume of carbon monoxide in the gaseous products when permissible explosives are detonated in contact with coal dust. Thus, reactive materials of a reducing nature adjacent to explosives loaded in drill holes may decrease the effective oxygen balance of the explosive and cause the volume of toxic gases to increase.Several blasting accessories of reducing nature have been introduced recently for use in coal or metal mines or tunnels. In practice these are loaded adjacent to the explosive where conditions favor reaction with the products of detonation. The effects of this loading on the gaseous products obtained from the shot are indicated in this report. Broad consideration was not given the efficiency, usefulness, or over-all safety of these devices, but the practical significance of the hazard resulting from increased volume of carbon monoxide is discussed."

May 1, 1942

By M. P. Dalton

This paper which describes the milling practice at the Morning concentrator of the Federal Mining and Smelting Co., Mullan, Idaho, is one of a series being prepared by the Bureau of Mines. ACKNOWLEDGMENT The author wishes to acknowledge the assistance given by H. G. Washburn, general manager of the Federal Mining and Smelting Co., and by C. S. Price, assistant mill superintendent, in the preparation of this paper.

Jan 1, 1932

By Joseph M. Singer

Having established that sodium chloride reduces the incendivity of explosives, the Bureau of Mines studied the effect of sodium nitrate in reducing ignition hazards. Gallery experiments showed that sodium nitrate reduced the incendivity of certain explosives to 8 percent natural gas in air but increased their incendivity to coal dust predispersed in air. Laboratory experiments using hot jets from explosions of stoichiometric mixtures of methane-oxygen-nitrogen showed that both sodium chloride and sodium nitrate reduced the incendivity to methane, to mixtures of coal dust and methane) and to coal dust. The difference between the gallery and laboratory results with respect to coal dust is attributed to temperature-time effects.

Jan 1, 1967

By R. V. Ramani

In this report, the application and limitation of the various equipment available for surface coal mining are discussed. The correction factors for adjusting equipment performance arising from machine design, material characteristics, and modes of operation are presented. Engineering design, pit layout and equipment selection are discussed with mathematical derivations. Two computer programs (SMCALC and SMRES) have been written to aid in pit design and equipment selection. The Strip Mine Calculation Program (SMCALC) can be used to select the bucket size and reach of shovels and draglines for various pit widths. It will also calculate the number of drills, loading shovels, trucks and bulldozers needed to achieve a production target. The Surface Mine Reclamation Equipment Selector (SMRES) can be used to select the number of bulldozers, scrapers and front-end loaders needed to achieve the desired production.

Jan 1, 1976

By Thomas C. Ruhe

The Pittsburgh Research Laboratory of NIOSH conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) conserves energy, reduces oil imports, and reduces mining costs. Since RO has a variable composition, there was concern that the additives/impurities it contains may cause ANFO made with RO to be unstable (as compared to regular ANFO) at high summer ambient storage temperatures. Reactivity of RO with zinc was also a concern. Thermal stability tests were conducted to help quantify and resolve these issues. ANFO mixtures (0.66 lb/300 g) were put into sample containers made of steel, stainless steel, and galvanized (zinc coated) steel pipe fittings, which were heated in isothermal ovens. The experimental parameters were temperature settings of 140° F (60° C) and 176° F (80° C), four sample container (pipe fitting) metal combinations, and nominal heating periods of one and three days. The ANFO samples contained 6% each of the following twelve different oils/oil mixtures: No. 1 was diesel fuel, Nos. 2 thru 6 were five candidate oils (2 thru 5 were used oils and 6 was a new synthetic oil), No. 7 was 5% diesel fuel + 1 % graphite, and Nos. 8 thru 12 were 3% diesel fuel + 3% each of the five candidate oils. All samples showed no reactivity when heated at 140° F (60°C). All samples (except No. 7) reacted at 176° F (80° C) in a steel pipe with galvanized caps as follows: No. I reacted most, Nos. 8-12 reacted moderately, and Nos. 2-6 reacted least. All ANFO samples were tested and found not to be cap sensitive.

By Eldon K. Stanek

The material presented in this chapter is a review of the work done during the period from June 23, 1972 to June 22, 1973 which was reported in detail in the first annual report for Grant No. 60122088 which was submitted on June 29, 1973. This report has appeared in the National Technical Information Service as bulletin number PB230 972/AS. 1.2 ANALYTICAL PREDICTIONS OF INDUCED VOLTAGES AND CURRENTS The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable, although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available from either handbooks or the manufacturer's published data. Thus, it is useful to present the results of the derivation of the inductance matrix and a few intermediate steps.

Jan 1, 1975

By Clinton C. Knox

To demonstrate the feasibility of unwatering ore reserves previously indicated in the virgin Melrose zinc-lead field in Kansas and Oklahoma, the Bureau of Mines .carried through a pumping project on the Park Walton farm in 1943. Due to success of the undertaking, attention was turned to exploration of other indicated ore deposits and promising areas within that part of the field benefited by .the drainage project, By the middle of 1946, four private mining companies were active in the field; and a considerable output of lead and zinc concentrate had been obtained from the new Park Walton mine and mill. The Park Walton Ore deposit was unwatered by installing deep-well pumps in three holes previously drilled by the lessee. Pumping was continued by the Bureau of Mines at a rate of 2,500 to 1,000 g.p.m. for about 6 months; during this time the local static artesian water-level, originally averaging 108 feet below the surface in the old drill holes was lowered to the 316-foot level, which justified beginning the initial shaft sinking and mine developments. In all, about 750,000,000 gallons of water was pumped by the Bureau of Mines at an operating cost averaging $0.024 per 1,000 gallons.

Jan 1, 1948

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By G. R. FITT, S. R. B. Cooke, C. W. Davis, V. H. Gottschalk, C. G. Maier, C. E. Wood, R. S. Dean, S. B. THOMAS, John Gross, E. P. Barrett, T. L. Joseph

Lack of funds has prevented publication of much of the metallurgical work of the Bureau of Mines during the past 2 years . The present progress report covers studies in the direct production of iron and steel . The experimental work was carried out in cooperation with the universities of California , Minnesota , and Missouri . Complete reports will be published when funds are available .

May 1, 1934