Search Documents

By Mark R. Pettitt

Noise surveys conducted in underground coal mines have consistently indicated that auger mining machines subject the operator and helpers to excessive noise exposure. The machine cutting heads have been identified as the primary noise source. This report documents the research program conducted to (1) investigate the nature of the cutting head noise problem, (2) develop noise control concepts, (3) devise in-mine survivable techniques to implement the noise control concepts, and (4) build and demonstrate prototype reduced-noise auger miner cutting heads. The dynamic forces generated during coal cutting by the brittle fracture of coal are predominently low frequency. The low-frequency (less than 1500 Hz) structural response of the cutting head, therefore, determines the noise radiated by the cutting head. The most feasible methods of reducing the cutting head low-frequency response are to increase both the structural stiffness and the low-frequency damping. A technique was devised to achieve these goals. The standard plate helix was replaced by a sand-filled hollow helix of triangular cross section, and the core diameter was increased with an attendant reduction in helix depth. Extended in-mine tests demonstrated the operational capability of the reduced-noise auger cutting heads. The simple noise control concepts are valid for all continuous miner cutting heads. The sand-filled hollow helix technique, which achieved a 10 dB(A) noise reduction for the auger, can be used on any helix-bearing Cutting head.

Jan 1, 1983

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By Robert J. Brennan, Edward R. Navrocky, John W. Buch

In an effort to establish a highly productive mechanized mining system for anthracite beds pitching between 10 ° and 20 ° , for which conventional mobile equipment is not adaptable , the Bureau carried out an experiment in longwall mining using an Anderton- type drum cutter loader and friction - type yielding steel roof supports . The roof- support system proved to be inadequate for breaking the overhanging roof at the break line supports , with the result that the roof broke over the solid coal . The accompanying subsidence destroyed the continuity of the roof in the work area , and the project was discontinued .

Jan 1, 1964

By Dean H. Ambrose

Using three-dimensional (3-0) graphics computing to evaluate new technologies for computer-assisted mining systems illustrates how these visual techniques can redefine the way researchers look at raw scientific data. The U.S. Bureau of Mines is using 3-D graphics computing to obtain cheaply, easily, and quickly information about the operation and design of current and proposed mechanical coal and metal-nonmetal mining systems. Bureau engineers developed a graphics simulator for a continuous miner that enables a realistic test for experimental software that controls the functions of a machine. Some of the specific simulated functions of the continuous miner are machine motion, appendage motion, machine position, and machine sensors. The simulator uses data files generated in the laboratory or mine using a computer-assisted mining machine. The data file contains information from a laser-based guidance system and a data acquisition system that records all control commands given to a computer-assisted mining machine. This report documents the first phase in developing the simulator and discusses simulator requirements, features of the initial simulator, and several examples of its application. During this endeavor, Bureau engineers discovered and appreciated the simulator's potential to assist their investigations of machine controls and navigation systems.

Jan 1, 1992

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963

By Oren C. Baptist

Umiat field contains the largest accumulation of oil discovered so far in Naval Petroleum Reserve No. 4 in Arctic Alaska. The Umiat anticline was tested with 11 wells; 6 produced oil in varying quantities. Behavior of the wells during testing was unpredictable. For example, one well was abandoned as a dry hole after all tests failed to recover any oil, yet an offset well, only 200 feet from the dry hole, produced 400 barrels of oil a day. The main oil reservoirs are less than 1,000 feet deep and are in the permanently frozen zone (permafrost). Reservoir pressures are low, and most primary production will be by expansion of gas-in-solution in the oil. Because of the unusual reservoir conditions and the difficulties encountered in drilling and completing the wells, the Department of the Navy asked the Federal Bureau of Mines to make laboratory studies of the reservoir sand to determine the cause of well plugging and to provide laboratory information, to be used as an aid in estimating oil recovery from frozen reservoir rocks under solution-gas expansion from low-saturation pressure conditions.

Jan 1, 1960

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963

A general description of investigative work conducted by the Bureau of Mines at the, Missouri Valley. manganese deposits and leading to tonnage and grade estimates has been given in Report of Investigations 4375, part 1 of a three-part report of work done between July 1945 and August 1947. Basic factual information from which tonnage and grade estimates were drawn was derived through the drilling sampling of 238 large-diameter bucket-drill holes in 11 widely separated areas. Drilling areas were selected after careful reconnaissance, mapping, and consideration of earlier work done on the deposits by the Bureau of Mines, State agencies, and private organizations and individuals. Stratigraphic studies permitted extending the results compiled within the drilling; areas to outcrop and lightly covered manganiferous zones between an beyond drilling areas. The locations of drilling areas, drilling sections, and individual drill hues are shown on illustrations in part 1 f this report. The individual drill holes, aside from providing the basic information for tonnage and grade estimates, disclosed features affecting any future plan As exploitation. It in particularly significant that a large part of the visible outcrops is faulted end otherwise complicated by slides that give a false impression of the thickness, vertical location, and even the existence of manganese-bearing zones.

Jan 1, 1949

By Ross. C. Barkley

A computer program has been written to simulate ground vibrations induced by multiple-hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosives charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g. velocity, attenuation, pulse), or by backcalculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties are backcalculating individual pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shown to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included and additional verifications with field results are required.

Jan 1, 1983

By E. D. Gardner

This paper is a progress report on the study of mining methods and costs in the western United States and summarizes that part of the work pertaining to the undercut block-caving method of mining. Ore is mined on a large scale exclusively by the undercut block-caving method at the following six mines in the western United States: The Morenci branch of the Phelps Dodge Corporation, Morenci, Ariz.; the Ray mines of the Nevada Consolidated Copper Co. at Ray, Ariz.; the Inspiration Consolidated Copper Co. at Inspiration, Ariz.; the Miamo Copper Co. at Miami, Ariz.; the Ruth mine of the Nevada Consolidated Copper Co. at Ruth, Nev.; and the Consolidated Coppermines Corporation at Kimberly, Nev. The undercut block-caving method is also used at the mine of the Andes Copper Mining Co. at Potrerillos, Chile.

Jan 1, 1930

By S. B. Levin

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. During the fall of 1942, the Bureau of Mines put down nine diamond-drill holes at the Cape Rosier zinc-copper-lead mine in Hancock County, Maine, that aggregated 2,883 feet of bore. These holes supplemented 13 holes, aggregating. 5,501 feet, put down on the property about 2 years earlier by the St. Joseph Lead Co. Veins of mixed sulfides were intersected in 15 of the holes drilled. Beneficiation tests were made on samples of ore obtained from old dumps. Zinc-copper-lead sulfides occur at the Cape Rosier mine as lenses in a zone of altered agglomerate beneath and between a series of diorite sills. The mineralized zone strikes F. 17° E. and dips southeast. Between July 1881 and September 1883 the mine produced about 10,000 tons of ore reported to have contained 20 percent zinc, 2.8 percent copper, and some lead. The crude ore was hand-sorted, and some. 3,000 tons were reported shipped.

Jan 1, 1948

By Jack Wright

The analysis of water produced with crude petroleum has interested oil producers since inception of the industry. Records of the first analysis of mineralized water produced from an oil-productive formation are obscure, and references to the first use of brine analyses to assist in solving problems of petroleum production are not available in the technical literature. However, many early reports of the Federal Bureau of Mines5-8 and Federal Geological Survey,9-11/ as well as articles in engineer and geological journals12-14/ placed special emphasis on the importance, interpretation, and application of water analyses. One of the earliest applications of water analyses, and still a major one today, is for identification of intrusive waters in oil wells. This may be done by comparing the chemical constituents of a sample of water indigenous to the oil-productive formation with those of samples from upper, water-bearing formations within the same general area. Some earlier investigators recognized the need for Analyzing samples of all waters encountered in drilling operations. Ambrose15/ stated, in part, "In wells being drilled, the engineer should grasp every opportunity to get a true sample of water from each sand. . .," and, "The waters of each oil field are chemically different from those of another field." The validity of the latter observation and the importance of the former one have been borne out by comparing the results of analyses of many samples and noting the differences in relative concentrations of like constituents of waters from the a geological formation in different localities or oil pools.

Jan 1, 1957

By Raymond B. Ladoo

"The name bentonite has been applied to a group or series of clay-like materials characterized by an alkaline oxide and alkaline earth content of 5 to 10 per cent, fine grain Giza, high absorptive powers, and usually very strong colloidal properties.Bentonite probably represents no mineral of fixed composition, and its physical properties vary considerably. The type material from Wyoming is light yellow or greenish yellow in color, but from other localities it may be cream colored, white, gray, pink, dark brown or even black. It is exceedingly fine grained, very plastic and highly absorbent. The appearance may be dull or powdeay, but a freshly cut surface usually has a waxy luster. Some varieties have the appearance of wax and may be cut into very thin, translucent shavings. The fracture of the type material is roughly conchoidal, that of other varieties is platey and shale-like, while still others have no typical fracture. Bentonite is highly absorbent; .hen wetted it will absorb more than three times its weight or seven times its volume of water. Some varieties when wetted with water expand to more than six times (some experimenters report eight times) their original volume. The wetted material is exceedingly smooth and soft and feels like soft soap. Unlike most clays, bentonite is easily fusible at a comparatively low temperature.Under a high-power microscope bentonite seems to consist of extremely small, more or less rounded, grains of uniform size, but the texture of most varieties is so fine that individual grains can not be distinguished.Some varieties when finely ground and thoroughly agitated with water will stay in suspension indefinitely, forming a translucent gelatinous mass. The addition of small amounts of acids or sodium chloride seems to have little or no tendency to raid coagulation or settling. Other varieties of similar analysis and appearance go into suspension more easily, but settle out again in a comparatively short time. It has been suggested that the material which stays in suspension indefinitely is a true colloid of the emulsion or lyophilic type."

Oct 1, 1921

By Edmond Chin

The land mass of the Asia and Pacific region comprises 11 million square miles or about 15% of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest island or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The countries in the Asia and Pacific region represent some of the most vibrant economies in the world. Japan is undisputed as one of the world's leaders in manufacturing and commerce. Hong Kong and Singapore are significant both as entrepôt and banking centers. The economies of Australia, the Republic of Korea, and Taiwan compare favorably to the level of the industrialized countries in western Europe. Indonesia, Malaysia, the Philippines, and Thailand have maintained strong economic growth during the past two decades. All these countries in the Asia and Pacific region collectively constitute a significant bloc as to raw materials production and consumption, as to manufacturing, and as to world trade.

Jan 1, 1992

By J. B. Umhau

During 1928 the United States consumed 73,270 long tons of virgin or primary tin, which was approximately 7.5 per cent more than the 68,198 long tons con¬sumed in 1927 and equaled 41 per cent of the world's production in 1928 (approximately 178,000 long tons). Consumers' stocks amounted to 9,268 tons on January 1, 1928, and 8,587 long tons on December 31, 1928, a net reduction of 681 tons. In addition to the virgin tin accounted for above, 12,106 long tons of secondary metallic tin were used by manufacturers of tin products in 1928. These figures are the result of an inquiry addressed by the Bureau of Mines to manufacturers to determine the amount of metallic tin used by them; in reply, 1,307 establishments reported consumption in 1928. The distribution of the amount consumed by various uses, as shown in the allowing tabulation based on Bureau of Mines canvasses for 1927 and 1928 in comparison with consumption by uses reported by the War Industries Board for 1917, emphasizes the fact that new uses for tin have been developed in only minor or insignificant amounts. Furthermore, although the studies for recent years show that some older uses have been discontinued, the amounts involved were all small and insignificant. Variation in consumption from year to year parallels the fluctuations in demand for the already well-established tin products. For example, the manufacture of bearing metals and solders for motor cars and trucks required 19,000 tons in 1928 compared to 16,000 tons in 1927; the canning industry continues to require the greater portion of the tin plate and also much solder. Growth in the electrical and the more recently developed industries (aeroplane, refrigerators, radio, etc.), while affecting total consumption of bearing metals, solders, etc., has made little change in the proportions required for these basic methods of using tin.

Jan 1, 1929

By J. B. Zadra

During the investigations of the occurrence of manganese in the western United States, the Bureau of Mines received a 100-pound sample of manganese ore from the Doyle-Smith property, Yuma County, Ariz. Laboratory tests were made to determine the amenability of this ore to standard ore-dressing methods of concentration to produce a marketable-grade product. The Doyle-Smith claims are in northern Yuma County, within 15 miles of the Artillery Peak deposit. The lot of ore used in the test work was taken from the outcrop of a large, massive, irregular bed of oxide manganese ore found on the claims.

Jan 1, 1952

By David R. Peterson

This user's manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user's manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979

By R. S. Dean

"INTRODUCTION The metallurgical research program of the Bureau of Mines has been somewhat disorganized, but generally advanced by the increased activities of the war period. The present report is for the purpose of summarizing the work of the Bureau in this field for the past 15 years and indicating its future plan.Fifteen years ago the Bureau turned from its pioneer work on the physical chemistry of steelmaking to an emphasis on raking a pure steel synthetically, rather than by refining, that is, :producing each of the steel 'constituents in the pure state and combining them by simple melting. Such a procedure permits the use of less high-grade ores, not only of iron, but of the ferroalloy metals, such as manganese and chromium,This program has led to extensive work on iron-ore concentration, agglomeration, reducibility of ores and agglomerates, direct reduction of iron ores and concentrates by a wide variety of processes; special refining processes for iron, the production of pure mangenese, chromium, and cobalt from low-grade ores by electrolytic processes, the production of ferrochromium, ferronickel, and ferronickel-cobalt from low-grade domestic ores, and the development of many special alloys to effectively use the new products.The status of the work in each of these fields and the future program of work, together with a bibliography of papers and patents by the Bureau staff on each of these subjects, are given."

Jul 1, 1946

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By N. Kyriazi

A performance study of oxygen self-rescuers from the United States and other countries was undertaken as an assessment of present worldwide technology. The apparatus were tested a an breathing and metabolic simulator in the Life Support laboratories of the Bureau of Mines. Parameters monitored during the testing were inhaled levels of C02 and 02, inhaled gas temperature, and breathing resistance. The metabolic demand placed on the apparatus represented the average demand of the 50th percentile miner performing a 60- min man-test 4, as described in 30 CFR 11H. Results presented include ;apparatus service life and subjective comments as well as averages and peaks of monitored parameters.

Jan 1, 1984