Search Documents

By M. E. Hawkins

Mineral analyses and electrical resistivity measurements of 324 representative samples of oilfield brines from 24 oil-productive counties in Mississippi and Alabama are presented in tabular form. Results of the mineral analyses, which include calcium, magnesium, carbonates, bicarbonates, sulfates, chlorides, sodium, and barium (with strontium if present), are reported in milligrams per liter. Electrical resistivity measurements in ohm-meter2 per meter at 75° F are reported in ohm-meters in the tables. Chemical analyses of formation waters are helpful to operators having water problems associated with petroleum recovery; electrical resistivity values are helpful in making interpretations from electric logs.

Jan 1, 1963

By H. H. Schrenk

One phase of Bureau of Mines work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that such devices will be. available, the Bureau has established schedules of minimum requirements for oxygen breathing apparatus,3/ gas masks,/ supplied-air respirators (hose masks, air-line, respirators, and abrasive blasting helmets, hoods, or masks),5/ and dispersoid (dust, fume, and mist)

Jan 1, 1943

By T. E. Gray

This report describes the preparation characteristics of the three significant coal beds in Greene County, Pa. It is one of a series planned to determine which coals are suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 12.5 million tons of coal was produced in Greene County in 1956, of which approximately 10 million tons was cleaned mechanically in 8 cleaning plants. The Bureau of Mines has estimated that 3.5 billion tons of recoverable coal remained in the county as of January 1, 1954.

Jan 1, 1958

By P. M. Sullivan

Galvanizers' sal skimmings have been treated by two methods of leaching in attempts to produce preflux solutions suitable for use in galvanizing operations. Both water-leaching and acid-leaching procedures are effective, except in severely exhausted skimmings when water-leaching becomes impractical. A preliminary analysis of the skimmings is not required. Solutions in the recommended concentration range can be produced conveniently by control of pH, specific gravity, and chlorine content. A technician would require only a short period of training to be able to perform the operations described.

Jan 1, 1958

By Lindsly. Ben E.

"The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2Lewis3 states, ""The estimate of 80 to 90 per cent of the oil left underground does not seem incredible.""It is estimated by the writer that approximately 91 per cent of the oil originally held in the Elliott pool, was still in the formation on January 1, 1924, and that it would take at least 12 years, at the 1923 rate of production, to further reduce this quantity by one per cent of the original content.The progress made in the oil industry during the past few years relative to the prevention of evaporation losses; to improvement in cracking processes, whereby the gasoline yield from many crudes has been doubled and trebled; to the increased recovery of gasoline from natural gas; and many other developments, remarkable as they are, can be applied only to that comparatively small portion of petroleum products which are raised to the surface. A device or process which would cut development costs to one-half would probably result in a much smaller profit to the oil industry, than the profit derived from an additional 10 per cent recovery of the total amount of oil in a pool. Various methods have been used and many others proposed, for the increase of oil recovery from normally depleted sands.In France, oil sands are being mined by means of shafts and galleries. In other places, notably the Bradford, Pennsylvania field, the yield has been increased by means of water flooding, wherein water is introduced into the sand to displace oil, and drive it to producing wells."

Oct 1, 1926

By Jan C. Still

The Glacier Bay subarea is that part of the Juneau Mining District (JMD) within Glacier Bay National Park and Preserve (GBNP). It is the western portion of the JMD and consists of the land between the Fairweather Range crest and the Takhinsha and Chilkat Ranges crests (excluding that land east of Excursion Inlet.) Figure B-1 shows the area. It is bounded on the north by the Alaska-British Columbia International boundary, to the south by Cross Sound and Icy Strait, and contains Glacier Bay. During 1975 -1977 the Bureau conducted a detailed study of the occurrences, prospects, and deposits in GBNP (B_4).2 This work was in cooperation with the U.S. Geological Survey (USGS) under the provisions of the Wilderness Act (Public Law 88-577). As a follow up to this earlier Bureau work, limited studies were conducted, during 1985 and 1986, as part of the JMD study. This report covers the most important aspects of the earlier studies and the 1985 and 1986 studies. ACCESS The Glacier Bay area may be reached through Gustavus airport, a paved strip which is serviced by scheduled jet airliners in the summer and air taxi services year-round. The airport is connected to Bartlett Cove (GBNP headquarters) by an all-weather road. No other roads exist in the area except a skid road to the LeRoy Mine and mill in the Reid Inlet area. Much of the Glacier Bay area is accessible through the salt water inlets and fjords which are part of Glacier Bay. Cruise ships, charter boats, and fishing boats visit these inlets and fjords during the summer months. Elevations within the area range from sea level to over 15,000 feet in the rugged Fairweather Mountain Range. More remote areas are accessible by small boat, foot, or helicopter. Glacier ice is a year-round hazard to navigation in Glacier Bay, and during the winter months some of the more northerly inlets are frozen.

Jan 1, 2012

[Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand .for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions and hearing2/ relative to the need for the sway, the opinion ms expressed that crude oil held in storage for long periods had lost so much of its gasoline content that he economic significant of total stocks should be discounted materially. Therefore, a primary objective of the survey was to]

Jan 1, 1938

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. face drill. The instructions are based upon an actual installation made in the mine on face drill model 460-S. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other face drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other face drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By G. S. Rice, J. W. Paul, M. W. VONBERNEWITZ

This bulletin abstracts and reviews essential details of reports on 59 fires in different coal mines in the United States, describes the circumstances of origin and the methods of controlling or extinguishing the fires, and points out the lessons taught. all, the fires caused great damage to property and killed nearly 400 men. The data have been compiled from the records of the Bureau of Mines, which cover most of the major mine accidents in the United States since 1.908. The names of the mines concerned and of the persons connected with the management of those mines have been omitted in accordance with the usual policy of the bureau. The bureau hopes that this bulletin will be of service to all persons interested in lessening the fire hazard at coal mines and to all who may be called on to fight a mine fire.

Jan 1, 1927

By J. L. Kohler

The final report for Phase II of Bureau of Hines Contract J0134025 concerns the research and development of sensitive ground-fault relays for dc utilization systems in mining. Sensitive relaying employs very low pickup levels such that, when used in conjunction with very high resistance grounding, the exposure of a human to ventricular fibrillation is significantly reduced. To delineate the desired relay characteristics, the report begins by reviewing previous research in this area. A theory for the saturable transformer used to sense the fault current is presented. The design of the ground fault relay is described in sufficient detail that it may be duplicated. Test procedures and results are given. Finally, conclusions and recommendations related to Phase II are presented.

Jan 1, 1986

By Robert W. Geehan

"INTRODUCTION A preliminary examination of the Argentena mine was made in 'January 1945 by an engineer of the Bureau, who recommended investigation by diamond drilling. The Bureau conducted a core-drilling project at the mine from April 30 to August 4, 1946. Claims investigated are in sec. 33, T. 24 S., R. 58 E., Mount Diablo base and meridian, in southern Clark County, Nev., about 2.2 miles west of Goodsprings.The Argentena mine has been an intermittent producer of zinc-lead-silver ore since 1926. During the war years, ore was shipped to the Government stock pile at Jean, Nev., and to the International Smelting F. Refining Co.'s smelter at Salt Lake City, Utah. The mine has been shut down at intervals because of lack of a market for mixed oxidized zinc-lead ore.The 12 holes drilled by the Bureau totaled 1902 feet. The program was designed to test for faulted portions of the ore bodies know in the mine and to test favorable areas for similar ore bodies. As a result of this program, one faulted segment of the ore body was found, and it was established that no one was present in a second fault block. Similar blocks remain unexplored in the vicinity of the mine. Two holes drilled in favorable areas several hundred feet from the mine failed to discover new ore bodies."

Jul 1, 1947

By Manuel Gomez

This report presents low-temperature tar data from studies by the Bureau of Mines of tars produced in an externally heated (entrained state) pilot-plant-scale retort. Analytical data covering 20 low-temperature tars, derived from the. carbonization of various ranks of foreign and domestic coals, are tabulated. The character of the tar is discussed in relationship to carbonizing conditions and the rank of coal. It is seen that in carbonization techniques that employ entrainment or fluidization of the coal particle, carbonization conditions are secondary to coal rank with respect to tar-oil yields and composition. The influence of distillation conditions on recoverable yields of tar products is presented. The probable yield of commercially important chemical products, based on a ton of pure (moisture- and ash-free) coal, are predicted. INTRODUCTION Low-temperature tars produced by entrainment or fluidized carbonization techniques that employ internally heated reactors represent the most nearly primary tart produced by industrial processes. In brief, such a process involves the application of a heat gradient to the coal particle "boiling" or suspended in a turbulent state in the reactor chamber. Conditions are observed so that the coal particle remains suspended within the reaction zone by a gas stream for a time interval commensurate with maximum tar-oil yield. The heat necessary for the carbonization reaction may be obtained entirely from the hot (preheated) gas stream, or it may be derived partly from the combustion of the volatile products and char by the transport gases, usually air. The volatile material moves out of the carbonizing zone at a rate that approaches the velocity of the transport gas. Carbonizing conditions are ideal when a minimum particle residence time is obtained within the reactor at a given temperature and a maximum yield of condensable volatile matter is released. In industrial practice this objective is a compromise.

Jan 1, 1957

By John L. Miller

The synthetic fluormicas may be divided on the basis of silicon content into tetrasilicic, trisilicic, and disilicic. Properties of lead and barium disilicic fluormicas were determined to characterize these two representative members of the disilicic group. Properties described include unit-cell parameters from X-ray diffraction, optical data, chemical composition, density, melting point, and mechanical and dielectric properties. Both the lead and the barium micas were typically monoclinic; neither was sufficiently cleavable to yield usable mica splittings. Both yielded polycrystalline, machinable ceramics with excellent mechanical and dielectric properties.

Jan 1, 1963

Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress -appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions end hearings2/ relative to the need for the survey, the opinion was expressed that crude oil held is storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to

Jan 1, 1938

By Jeffrey B. Osmint

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1991

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7. 1882 (22 Stat. 829) to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1987

By H. Reginald Hardy

This report describes the results of a research project carried out to investigate the feasibility of using transducer arrays, located on surface or in shallow boreholes, above an active coal mine to detect and locate the source of underground microseismic activity which normally occurs during mining. The initial stage of the project involves the design and development of a self-contained mobile microseismic monitoring facility capable of use in remote field locations. Following this a variety of transducers, and transducer field installation techniques were investigated to obtain optimum sensitivity and high signal-to-noise characteristics. Preliminary efforts were also undertaken to develop semi-automated techniques for analysis of microseismic field data. Using the facilities and techniques developed field studies were carried out at a number of surface locations over a central Pennsylvania coal mine operating at depths of the order of 500 feet. In particular studies were con-ducted over a previously mined development area, troubled by extensive problems of roof instability, and over two longwall panels during mining. Although many of the field studies were carried out during the development stage of the project, results in general have been most encouraging. Limited results were obtained over the development area, however excellent microseismic signals, correlating with underground strata instability, were detected over both long-wall areas, proving the general feasibility of surface monitoring techniques. More recent studies, carried out as part of a subsequent project, and utilizing modified geophone installation techniques at a third longwall site, have verified explicitly the feasibility of measuring underground microseismic activity from surface locations. Sections of typical field data are included in this report along with a brief review of the studies carried out at each of the field sites. Detailed analysis of data obtained at the second and third longwall test sites will be presented in a later report.

Jan 1, 1974

By Arno C. Fieldner, J. W. Paul, WALTER A. SELVIG

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the quality and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition. and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines,July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.' Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.2 Descriptions and analyses of samples collected during the fiscal years 1913 to 1916 were published in Bureau of Mines Bulletin 123.3 The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1916 to 1919. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22, 85, and ,123, the same plan of geographical classi- fication has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1922

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC). Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-431' the semiannual reports were resumed.

Jan 1, 1950

By J. A. Herdlick

At the request of the War Production Board a preliminary examination of the Big Ben molybdenum prospect near Neihart, Cascade County, Mont., was made by the Bureau of Mines under G. N. Bennett, mining engineer, Bureau of Mines Montana district office, in September 1942. Formal investigation, consisting of sampling, core drilling, and metallurgical testing, was later undertaken and completed in 1943. Field work was directed by Robert D. O'Brien, mining engineer, Montana district office, under the supervision of E. W. Newman, supervising engineer, Montana district office. This report describes the deposit, presents the factual data obtained from the sampling and core-drilling operations, and summarizes the results of the metallurgical studies. The deposit was first located and prospected in 1922 by the present owner, Frank Mansikka of Neihart, Mont. Periodic examinations made by responsible mining interests were culminated in 1938 when the Federal Mining & Smelting Co. optioned and investigated the property. No ores have been produced from the deposit to date.

Jan 1, 1949