Search Documents

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By Michael J. Beus

This Bureau of Mines report describes field investigations conducted in the Coeur d'Alene mining district of Idaho to obtain data on rock stress and physical properties. The resulting information has been utilized as input to detailed finite-element analyses to establish structural design criteria for deep-vein mine shafts. Measurement techniques include the Council for Scientific and Industrial Research biaxial and triaxial strain cells, the U.S. Geological Survey solid-inclusion probe, and the Colorado School of Mines dilatometer. Physical property testing was conducted in the laboratory on core obtained from each test site. Limited in situ physical property tests were also conducted. Reason-able success was obtained with the CSIR equipment, which was considered the most suitable for stress measurement in the study area. Test sites ranged in depth from 1,200 to 7,700 feet and are described in detail. The stress data were reduced by least-squares linear regression techniques to enable prediction of vertical and horizontal stresses to 7,500 feet. Ratios between the horizontal stresses as utilized for shaft design varied considerably, and a hydrostatic condition is the exception, based on Bureau measurements. Physical properties also varied widely, due to the complex geologic structure. Analyses of the data in terms of the tectonic history of the area show reasonable correlation. Data from previous rock mechanics investigations from the Coeur d'Alene district were also compiled and presented as part of this report to justify any generalizations regarding stress conditions and physical properties of the district as a whole.

Jan 1, 1980

By William A. Hustrulid

A technical and economic evaluation of the potential for improving mining productivity through the use of underreamers in blastholes, specifically in relation to Minnesota taconite, Arizona surface copper and in situ mining operations is presented. Included are (1) a review of the drilling and blasting practices presently being used, (2) a discussion of current underreamer technology. (3) the presentation of a general economic cost model for underreaming, (4) the application of the model to surface taconite, surface copper and in situ mining, and (5) a summary discussion including required performance specifications, potential overall benefits, and recommendations for further development.

Jan 1, 1977

By Wilton Johnson

Native asphalt was produced in 1981 by five companies in three States, Alabama, Texas, and Utah. Texas was the leading State in production of native asphalt. Total production increased in 1981 to 1.26 million tons, while value increased 10.5% to $27.7 million. Bituminous limestone, used primarily for street and road repair, was produced by Whites Uvalde Mines and Uvalde Rock Asphalt Co., both in Uvalde County, Tex., and Southern Stone Co., Colbert County, Ala. Gilsonite was produced by American Gilsonite Co., Uinta County, Utah, and Ziegler Chemical and Mineral Corp., Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1982

By Robert M. Strong

The following report is a summary of the commercial results which 'Were obtained from 2,000 tests conducted by the technologic branch of the United States Geological Survey at St. Louis, Mo., and Norfolk, Va., in 1907 and 1908, under the technical supervision of R. H. Fernald, engineer in charge of the producer-gas section. The tests dealt primarily with gasoline, forming part of the investigation of mineral fuels provided for by acts of Congress. To determine the relative economy and efficiency of gasoline it was compared with denatured alcohol. The tests, many of which were undertaken in connection with work for the Navy Department, supplemented, to a certain extent, the work of previous investigations, but only so far as was necessary to emphasize some of the more important points and to lead up to the defining of conditions required for the economical use of gasoline and alcohol. In order to determine and eliminate the affecting engine conditions as far as possible, the investigation was commenced by making comparative gasoline and alcohol tests on the same engines. These tests were repeated on other engines of approxiElately the same size and speed, having different degrees of comFression, different methods of governing, and different carburetors. The final report will include much material that may be of use in engine design, but that side of the investigation was not pursued any further than was necessary to obtain the best possible results, for alcohol and for gasoline with the engines at hand, and to prove that the minimum fu·el-consumption rate for each could be obtained in approximately the same manner. The effects of engine and of operating conditions both have a bearing on the commercial deductions but will be discussed only in a general way at this time.

Jan 1, 1911

By Llewellyn A. Rubin

Under Bureau of Mines Contract H0122007, Telcom, Inc., with the assistance of Fenix & Scisson, Inc., conducted a 17-month research and development project aimed at provid¬ing a field-test model of a guidance system for use with the Bureau of Mines Probe Drill. The Probe Drill is a part of the Bureau's Mine Rescue System developed under Contract H0101262. Volume I of this report is subdivided into seven sections. Volume II consists of a number of supporting appendices. In addition, there were delivered under the Contract, a number of other documents which are referenced in the text. Section 1 deals with essential contract information, Program Background, and a general system description. Section 2 covers the project chronology in brief. Section 3 is a digest of design considerations and implementation related to the requirements of the Contract. Section 4 is a description of the System, including illustrations of the hardware, and software. Section 5 is devoted to Operation and Maintenance. Para. 5.1 describes step-by-step field assembly and disassembly of the downhole unit. Para. 5.2 covers Operation. Para. 5.3 covers various aspects of maintenance from the lowest field echelon possible. Higher level maintenance must be accomplished in the laboratory, for the present field-test model. Para. 5.4 covers system calibration. Para. 5.5 covers detailed step-by-step operational sequences. Section 6 covers the results of the field testing, post-test evaluation, and recommendations. Essentially, we conclude that the present hardware (field-test model) has proven every aspect of system performance, but failed to provide reliable assurance of an operationally ready system. Telcom, therefore, recommends a three-phase continuing effort devised to provide the operationally-ready model of the system.

Jan 1, 1973

By H. S. Kalman

A table of factors for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, at base conditions of 14.7 psia and 70° F, is presented. The table covers a pressure range from 10 to 10,000 psin in 10-psi increments and a temperature range of 0° to 120° F in 2° increments. The volume of helium is calculated from the observed pressure and temperature of the helium, expressed as a factor from the table, and the known internal volume of the container. The calculation requires a single multiplication. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1968

By H. E. Heide

The serious shortage of domestically produced asbestos during the war prompted the Bureau of Mines to investigate reported asbestos deposits in Alaska. The most promising' appeared to be these in the Cosmos Hills and Jade Hills areas along the Kobuk River in northwestern Alaska. The deposits along the west side of Shungnak River, a tributary of the Kobuk River, were the first to be investigated by the Bureau, in the summer of 1944. Four bulldozer trenches were excavated, from Which a 2-ton sample was taken. This sample was shipped to Rolla, Mo., for testing in the Bureau of Mines laboratory. In the summer of 1945 an investigation of asbestos deposits on Cosmos Creek, also a tributary of the Kobuk River, was begun; the work was completed during the field season of 1946.

Jan 1, 1949

By Eric S. Weiss

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on typical U.S. mine ventilation stoppings in the NIOSH Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM). An innovative Australian-designed brattice stop-ping was also evaluated. After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to prevent future occurrences. As part of these postexplosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, is documented as evidence of the approximate strength and the direction of the explosion forces. The LLEM data showed that a typical dry-stacked and coated solid-concrete-block stopping survived a total explosion pressure of ~6.7 psi (~46 kPa) and was destroyed at a total explosion pressure of ~7.6 psi (~52 kPa). In comparison, a typical dry-stacked and coated hollow-core concrete block stopping survived a total explosion pressure of ~3.4?4.3 psi (~23?30 kPa) and was destroyed at a total explosion pressure of ~3.6?5.2 psi (~25?36 kPa), depending on the length of the pressure pulse and the value of the pressure-time integral. A typical steel panel stopping design survived a total explosion pressure of 0.8 psi (5.5 kPa) and failed at a total explosion pressure of 1.3 psi (9 kPa). The LLEM data also showed that an obstacle blocking the path of a pressure wave resulted in a higher reflected pressure at the obstacle. An 8-in (20-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~26 psi (~180 kPa); this stopping was not tested to failure. A 6-in (15-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~14 psi (~97 kPa) and was destroyed at a total explosion pressure of ~25 psi (~172 kPa). An innovative Australian woven cloth stopping survived an explosion pressure of 4.0 psi (27 kPa) and was destroyed at an explosion pressure of ~6.1 psi (~42 kPa). These results will help investigators determine the approximate explosion forces that destroy or damage stoppings during actual coal mine explosions.

Jan 1, 2008

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By Walter W. Fowkes

Leonardite is a coallike substance, similar in structure and composition to lignitic coal and believed to be derived from lignitic coal by the process of natural oxidation. Leonardite is little known outside lignite-producing areas and has been developed commercially only to a minor extent. The higher oxygen content and less compact structure of leonardite, compared with lignite, make it undesirable as a fuel but indicate that it has potential as a source of chemicals and for other nonfuel uses. It is a convenient source of humic acids. The United States has a large natural reserve of leonardite; furthermore, it can be produced in the laboratory under controlled conditions. The significant elemental difference between leonardite and lignite is the oxygen content (leonardite, 28-29 percent; lignite, 19-20 percent). The higher oxygen content of leonardite is due entirely to a Larger number of carboxylic acid groups. This fact explains the 17-Cold increase in alkali solubility of leonardite. Spectral studies indicate that the material is mixed salts of humic acids.

Jan 1, 1960

By E. C. Fitch

This report discusses fire-resistant hydraulic fluid safety from three different directions. First, results of a survey prepared for the Fire Resistant Hydraulics Journal by the staff of the Fluid Power Research Center are analyzed. Second, operational limitations of fire-resistant hydraulic fluids are examined. Finally, laws and standards of various foreign countries are investigated. Three conclusions are derived from a close study of fire-resistant hydraulic fluid safety from these three directions. First, a significant number of experts in the fluid power industry are no in agreement about aspects of fire-resistant hydraulic fluid fire-resistance and toxicity. This indicates a need for more in depth research. Second, the use of fire-resistant hydraulic fluids involves a compromise between the decreased fire hazards and increased toxicity and machine incompatibility problems. Finlly, major foreign governmental agencies have thorough laws and standards concerning fire-resistant hydraulic fluids. These laws and standards may provide a solid framework for further international research into fire-resistant hydraulic fluid safety.

Jan 1, 1979

By Launa Mallett, Charles Vaught, Michael J. Brnich

Purpose: This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings. Intended Use: This material has been developed for use in short safety-training sessions such as start-of-shift safety or Atoolbox@ talks. The information can be presented in approximately fifteen minutes and is appropriate for workers at all experience levels. While the examples and illustrations are taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. Materials Needed: The instructor will need to prepare the figures provided in a form that can be seen by the entire class. Suggested methods include the use of: (1) overhead transparencies, (2) laminated pages that can be held up for small groups, and/or (3) handouts with copies of the figures for each trainee. As a supplement, stickers featuring the communication triangle can be placed on hard hats, telephones or other communication devices to remind workers about the key to effective emergency communication. The Talk: The accompanying script is a guide for presenting this safety talk. Training is enhanced if these materials are covered but not simply read by the trainer. Examples given in this guide are from real experiences. To make training more interesting and effective, the instructor can substitute examples from his/her workplace. Additional Resources: The following references will provide further information about communications during emergencies. Auf Der Heide, E. (1989). Disaster Response: Principles of Preparation and Coordination. The C.V. Mosby Company, St. Louis. Mallett, Launa, Charles Vaught, and Michael J. Brnich Jr. (1993). A Sociotechnical Communication in an Underground Mine Fire: A Study of Warning Messages During an Emergency Evacuation@, Safety Science, 16, pp. 709-728. Nigg, J.M. (1987). A Communication and Behavior: Organizational and Individual Response to Warnings@ in Sociology of Disasters: Contributions of Sociology to Disaster Research, R.R. Dynes, B. De Marchi, and C. Pelanda (eds.), Franco Angeli, Milan, Italy, pp. 103-116.

Jan 10, 1999

By C. E. Hennig

On January 1, 1961 there were 311 petroleum refineries in the United States with a total crude-oil throughput capacity of slightly more than 10 million barrels per day, according to the Bureau of Mines' annual survey. Compared with a year ago, this represents net increases of one in the number of plants and 109 thousand barrels per day in total capacity. Contributing to this increase was the completion of two new plants, one in Hawaii and another in Michigan, during the year. At the beginning of 1961 the industry was building facilities which will increase this overall crude capacity by 36,500 barrels per day. As part of its building program, it was also replacing 329,000 barrels per day of its present capacity. Of the total 10 million barrel per day installed capacity, the industry reported 380,000 barrels per day as being shut-down on January 1, 1961. This included 11,500 barrels per day considered inoperable without extensive reconditioning.

Jan 1, 1961

During the initial portion of the contract several alternative designs were considered, as set out step by step in the monthly reports. The conclusions reached during this period were - to use on INTERDATA Model 70 as the system minicomputer - to drop the idea of multiplexing and digitizing the inclinometer outputs downhole due to the greater complexity and cost that that alternative would imply - to use a multitasking software monitor to enable synchronization of the several tasks that the system would have to perform simultaneously - to use a common controller for all I/0 devices except those which were available off the shelf from Interdata - to use a sheave counter to meter off equal increments of probe travel, but to supplement this information with the use of an encoder on the winch drum in order to be able to measure total probe travel unambiguously. - to place all I10 device interfaces in a bin connected to the common controller. During this period considerable attention was dedicated to the design of the mechanical components contemplated it the original contract. Of these, only those required for vertical probe was complete at the time that it was decided to forego the mechanical subsystem and concentrate on developing the necessary electronics and software to interface with the probes being developed by the Bureau of Mines.

Jan 1, 2012

To be able to continuously monitor the noise to which underground workers are exposed as a better way to help prevent hearing damage. The Approach: The Bureau of Mines has developed a Time-Resolved Audio Dosimeter which can be worn by miners to record noise level every 30 seconds and store It in a miniature solid state memory. Figure 1 is a photo of the dosimeter. [ ] How It Works: Acoustical noise is picked up by a micro-phone and fed to a sound level meter which produces a d-c voltage proportional to the A-weighted sound pressure level. (As specified by federal regulations, the A-weighted sound pres-sure level approximates the response of the ear by discounting the higher and lower frequency components of the noise.) This d-c voltage controls an oscillator which, together with related circuitry, produces a pulse train having a frequency that's proportional to the noise level.

Jan 1, 1975

By Ralph D. Gift

This report describes a program of research to evaluate methanometry in coal mines. The program commenced by conducting an extensive state-of-the-art survey. Details of the survey are presented which includes a rating of various types of instruments that can be used to detect and record methane gas. Laboratory test data, on mine instruments tested are presented together with results from a computerized statistical analysts.

Jan 1, 1972

By R. V. Petrella

The flash induced combustion of Sewell and Pittsburgh coals was studied in air and in oxygen. The primary decomposition and combustion processes occur within the first 300 ~sec in oxygen and slightly later in air. Strong absorption spectra of CN and OH are indicative of the decomposition and combustion processes, respectively. Kinetic spectroscopy and combustion product analyses indicate that only about 35% of the coal dust is consumed in the explosive combustion which takes place in several (1-5) distinct but similar steps. The combustion-modifying effects of (NH4)2HP04, NH4H2P04, KHC03 and Rock Dust were studied in the 1-20 wt % range in coal dust flash com-busted in air and oxygen. The study reported herein shows Rock Dust to be the most efficient coal combustion inhibitor. KHC03 is the least effective agent, with the phosphate salts showing marginal effectiveness.

Jan 1, 1976

By P. -E. Boileau, P. Marcotte, Y. Aldien, S. Rakheja

A number of biodynamic models of the hand-arm system have evolved on the basis of measured driving-point mechanical impedance (DPMI) responses to facilitate analyses of the coupled hand-tool system [1]. The parameter identifications in such models are based upon minimization of an error function of the model and the target impedance data, which may not yield a unique solution. Consequently, a number of model structures and parameter sets could be realized that would equally satisfy the target curve. Moreover, the vast majority of the reported models exhibit acute deficiencies due to excessive static deflections of model masses, presence of a low frequency mode and very light masses in the order of 1.2- 4.8 grams. The models also do not characterize the dependency of the biodynamic responses on many factors, namely the hand forces, hand-arm posture and vibration intensity. This study aims at development of a hand-arm biodynamic model with considerations of the hand forces, and both the DPMI and power absorption measures, to enhance the uniqueness of the model. Methods Two different model structures are chosen for identifying the model parameters on the basis of measured DPMI and absorbed power characteristics of the hand-arm system under zh-axis vibration over a range of hand-grip and push forces. Owing to the strong influence of the hand-handle coupling forces, the models were initially derived for fixed hand forces, namely 30 N grip and 50 N push forces, as suggested in the ISO 10068 standard [2]. The equations of motion for the model are formulated and solved to compute both the DPMI and absorbed power responses. A constrained minimization function comprising weighted errors of both the DPMI and absorbed power is formulated and solved to identify the parameters. Alternate functions corresponding to different combinations of hand forces are then applied to identify hand-force dependent model parameters. Variations in the model parameters are investigated as functions of the grip, push and coupling forces through linear regression analysis. Regression-based models are formulated for deriving the hand-handle forces dependent model parameters. The validity of the model is also examined under selected combinations of hand forces. [ ]

Jan 6, 2006

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing, and grinding methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that in many instances publication of total production costs may cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The following report deals with the methods employed by the Malvern Clay Co., Malvern, Carroll County, Ohio. The author wishes to acknowledge the assistance of the following persons: H. C. Ross, vice-president and general manager, and H. C. Dormer, secretary and treasurer.

Jan 1, 1937