Search Documents

By Sehoon Lee, Duhwoe Jung, Eunsu Cha, Kyeonghwan Jeong

This case study presents the effectiveness of underground rock blasting to facilitate the trench cut in the hard rock layer using a conventional trench cutter for the construction of a diaphragm wall. Rock blastings are pre-performed up to the scheduled depth and then the fragmented rocks can be easily cut using a conventional trench cutter. Two trial underground rock blastings have been performed and the effectiveness of pre-blasting is presented in terms of a cutting rate, a loss of cutter heads and an amount of overbreak. Based on the results obtained from the trial underground rock blastings, the following conclusions can be appropriate: 1) A pre-blasting of hard rock layer located in depth can help to overcome the limitation of the trench cut using a conventional trench cutter. If the hard rock layer is fragmented after blasting, the fragmented rocks can be easily cut using a conventional trench cutter, 2) The speed of cutting works was accelerated and the loss of cutter heads was significantly reduced in the sections where the blastings were applied prior to cutting. 3) The amount of overbreak, expressed in terms of the amount of poured concrete, can be reduced to some extent. However, the location of blast holes in the trench can also contribute to the amount of overbreak. The closer the location of blast holes to the edge of the trench, the more extensive fractured and cracked zone can be formed on the face of the trench. This can increase the amount of overbreak if the trench is left empty for a while.

Jan 1, 2000

By Greg Mclellan, Mark Johnson, John Pepper

Several large quarrying projects recently occurred in Miramar, Florida. These were closely monitored by the Seismologist of Record and Broward County in accordance with County and City regulations. In addition to this monitoring, the City of Miramar employed The Pepper Engineering Group, Inc., to provide additional spot check monitoring and to review the records of the other two parties on a routine basis. Broward County ordinances require that the location of each shot and the nearest protected structure be recorded along with seismograph measurement of each shot at the nearest protected structure. The positions of the blasts and nearest protected structures were determined using GPS. The blast vibrations were measured by seismograph. Over 600 shots, which are the subject of this study, were measured both by the County, the Seismologist and, on many occasions, The Pepper Engineering Group. As such, the vibration data was constantly cross-checked for consistency. The blasting contractor also provided blast designs for each shot. In this paper, the measured vibrations are plotted in terms of Resultant Peak Particle Velocity (RPPV) versus Scaled Distance (SD) on logarithmic scales. The data curves are fitted with least squares and upper 95% and 99% prediction limits are provided. Equations are presented to predict the RPPV based on scaled distance and prediction level using power fits. Statistical information concerning the derivation of the various limits is presented. The raw data used to develop this paper, along with other information concerning the shots, will be posted on the Internet for use by other researchers.

Jan 1, 2000

By Raimo Vuolio

"Over the past 30 years, the Nordic countries have developed similar practices for estimating damage caused by rock blasting vibrations. However, over the last few years the risk of damage has sometimes been estimated by using international values, which have created unnecessary costs, since they are too conservative. This paper gives a proposal for Finnish blast vibration standards and a calculation model for the extent of the zones for building inspection, risk analysis, and vibration measurements. The international conclusion is that particle velocity is the best descriptor for limiting damage potential for structures. Over 900 000 vibration data recordings from 52971 blasts were collected for this paper during 1970-1989. They show that the most practical description is the vertical component of the peak particle velocity. As rock is a nonhomogeneous medium, it is hard to predict the need and scope of risk analyses, building inspection, and vibration measurements. As a large number of blasts were monitored for the recording of the peak particle velocity in several locations in Finland, and the data combined, it is possible to establish safe scaled distances for the calculation of the need and scope of risk analyses, building inspections, and vibration measurements."

Jan 1, 1991

By Paul Sairato, Cathrine E. Johnson

Recruiting and retaining students in the explosives industry is becoming increasingly important each year. With no undergraduate degree in explosives engineering currently available in the United States, it is from other industries and degree disciplines we must recruit. The 2014 annual ISEE conference saw the first anonymous online survey distributed to members of SEE student chapters of the International Society of Explosives Engineers. The survey contained questions about future job and career plans, ideal job placement, expectations of salary and current academic degrees. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry, and their current path to pursue this. This information can help steer recruitment activities and job offers for graduating students. The success for both student response rates and interest from the industry has allowed space for a yearly update of this survey. This paper provides the data from a second, restructured, online survey distributed to all student members of the International Society of Explosives Engineers, globally. Understanding the main incentives for a student to accept a graduate position as an explosives engineer can help us, as an industry; position ourselves to remain competitive in recruiting against other major degree disciplines.

Jan 1, 2015

By Christopher Smith

The critical nature of detonator function in blast design and its effects upon performance and safety of a blasting operation are well documented. Numerous laboratory and field studies have shown dynamic shock waves, generated by the detonating explosives in a shot, to be detrimental to the performance of the explosive columns in the adjacent boreholes. Laboratory tests conducted in Japan have explored the possible effects of dynamic precompression upon cartridges of emulsion explosives, which had been sensitized with different hotspot void producing methods. These tests uncovered significant differences in the magnitude of the dynamic shock wave pressures measured inside the different emulsion explosive cartridges, and demonstrated these pressure differences by crushing detonator shells inserted inside the emulsion cartridge. Basically, the results of these tests clearly showed the magnitude of the compressive force applied to the detonator inside the primed explosive cartridge to be a function of the mechanism that had been used to sensitize the emulsion (i.e., glass microspheres, plastic spheres, chemical gassing). The current study was designed to further explore the actual detonator failure mechanism in these dynamic precompression tests using live detonators inside the emulsion cartridge as opposed to empty detonator shells. The testing involved inserting commercial delay detonators inside emulsion charges, which had been sensitized with common hotspot void producing agents, and subjecting the primed explosive cartridge to the dynamic pressure wave generated by an underwater donor explosive charge. The effects of variations in the emulsion’s sensitization method upon the damage inflicted to the detonator were studied. Depending upon the degree of detonator damage, detonator crushing can lead to varying degrees of detonator malfunctions, ranging from sympathetic initiation of the detonator, to a reduction in delay time accuracy, to reduced detonator output, to complete detonator failure. Each of these malfunctions can have serious detrimental effects upon the performance and safety of a blasting operation.

Jan 1, 2006

By Dale S. Preece, Vanessa S. Berg

Shaped charges are being utilized in defense applications against a wider variety of targets including concrete, rock, and soil. This work was motivated by a heightened interest in characterizing the effect of shaped charge attack on brittle, non-homogenous materials, in particular, concrete damage and penetration predictions resulting from a TOW-2a conical shaped charge (CSC). This paper presents a multi-stage approach for accurately predicting the high explosive detonation and subsequent jet formation due to the collapse of shaped charge liner, the changes in jet length and diameter as a function of standoff distance, and the jet-target impact dynamics. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN to predict the shaped charge jet formation. 2-D finite difference Eulerian subgrids represent the explosive and casings components, while thin components like the liner are modeled with Shell subgrids. The Pugh, Eichelberger & Rostoker (PER) jetting theory option is invoked to obtain the jet and slug masses and associated velocities. The jetting data is post processed where the jet velocity gradient and jet mass is used to solve for the new jet length and diameter gradient at a desired standoff. The final computation involves a 2-D fully Lagrangian model in which the jet and velocity gradient is represented by a string of Lagrangian segments and the concrete target is defined as Lagrangian with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model. This model has a third invariant dependency that accounts for failure mechanisms in brittle materials.

Jan 1, 2004

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining; on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years.

Jan 1, 1998

By Lawrence Mirabelli, Wayne Lidkea, Mario Paventi

On Januarv 1, 1996, INCO Limited, Tamrock OY, Dyno Nobel and CANMET formed a consortium for the development of robotic mining equipment called the Mining Automation Program (MAP). This project was a tive- [5] year research and development program that combined the talents of the above organizations to facilitate the development of mining equipment and systems for tele-remote mining. The year 2000 brings MAP to conclusion with actual production process trial testing of the developed prototype equipment and systems during the period between May and October. MAP consisted of multiple projects all of which are based on the communication system developed by INCO Mines Research and currently sold and marketed by Automated Mining Systems Limited. The main projects include the development of a positioning and navigation module (including a software mapping system that will be inherent to each piece of equipment), robotic systems for underground development and stoping operations, as well as software systems to support the use of this equipment. Included in the program was the establishment of a Research Mine, at INCO’s 175 orebody, Copper Cliff, Ontario, Canada. This facility allowed for the on-site collaboration between the companies and research organization in the design and testing of techniques and equipment to mine with TeleminingTM. Some of the prototype equipment developed through the program are: a tele-operated drilling jumbo, a tele-operated load-haul-and-dump [LHD] tram, a tele-operated production drill, a remote initiation system for programming and detonation of electronic detonators, and the development of a vatiable energy bulk emulsion explosive system, including loading equipment, to deliver the explosives to boreholes. Use of tele-operated and automated equipment for mining mandates a dramatic change in the traditional drill/blast/muck/support cycles in the underground mining process.

Jan 1, 2001

By Fumihiko Sumiya, Yukio Kato, Yoshikazu Hirosaki

Secluential blasting is one of the most popular methods in blasting. tiowever, it is well known that an emulsion explosive can be dead-pressed by dynamic pressure generated by the previous detonation. It is difficult to gain the expected blasting performance due to tb.e malfunction of explosive caused by deadpressing and shock desensitization. Such malfunction of an explosive is undesirable for safety blasting operation. Voids in the emulsion explosives will considerably affect the performance of explosives such as sensitivity, detonation velocity (DV), pressure-resistance and so on. To clarify the detonability and the performance of precompressed emulsion explosives, the DV was measured. Three types of microballoon or micro bubble ; two types of glass microballoon(GMB), resin microballoon@MB) and chemical gas bubble ; were used as sensitizers for the sample emulsion expiosives. The underwater explosion test was carried out to load dynamic pressure into the sample explosives. The dynamic pressure was generated by the detonation of a donor explosive, and the DV of the sample explosives as acceptor was measured by ionized gap terminals. The dynamic pressure level and initiation interval for the donor and the acceptor were chosen as experimental factors. The detonability was carefully investigated at short initiation intervals taking into consideration the interaction between same delays caused by the deviation of the ignition time of the electric detonators. From these experiments, the following results were obtained ; A) The DV of precompressed emulsion explosives was low compared with that of uncompressed emulsion explosives in all pressure conditions. B) The decrease of DV in the sample explosives sensitized by GMB s was larger than that of DV in the sample explosives sensitized by RMBs or chemical gas bubbles. C) The recovery of the detonability occurred rapidly in the sample explosives sensitized by RMBs and chemical gas bubbles. However, a long period was needed for the recovery of detonability in the sample explosives sensitized by GME! s. It was concluded that the type of microballoon and micro bubble significantly influenced the detonability of precompressed emulsion explosives.

Jan 1, 2002

By Richard Mainiero, James H. Rowland III

For many years there have been small scale tests available for evaluating the toxic fumes production by capsensitive explosives (DOT Class 1. l), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agents in construction and mining, there is a need to determine the quantities of toxic ti,tmes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pet) tieI oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/set for the 1 to 10 pet range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4~mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding 5 and 10 pet aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

Jan 1, 2000

Blastserve, ISEE’s Listserve is being replaced by our new Blasters Forum-online, an exclusive member benefit. Our goal is to provide an ISEE forum for you to network with your peers and exchange technical information and get answers to your technical questions. This forum is unique in the fact that only ISEE members are permitted to review or post on the site. Over time you will be able review the discussion history and use the archived discussion as a valuable resource for trends in the industry. The following are a sample of the discussions that too place recently on Blastserve

Jan 1, 2013

By James R. Houston, Wendel Clay Chaffin, John Loviza

During the spring and summer of 1993 the largest pipeline in Tennessee was installed as part of the upgrading of Nashville's sewage needs through the year 2035. This new 3.3 million dollar outfall project is able to carry 330 million gallons of treated sewage water daily. Special projects required special equipment as this project was safely and quickly installed.

Jan 1, 1995

By Dr. Kyle Perry, Ryan Sibley

Rock blasting is an inherently difficult field to quantify independent & dependent variables and the specifics of how the energy interacts with the material for a number of reasons. Independent variables such as geology are innumerable and stochastic, thus, on a laboratory and full-scale basis these variables are assumed to be homogenous across the desired rock boundary. Dependent variables are difficult to quantify in the laboratory based on the specific aspect of the fracture mechanisms that caused the fracturing. The same variables are difficult to quantify in the field because of the shear amount of material being blasted. The energy interactions with the material are difficult to quantify due to the rate of the reaction and the lack of quantification of independent variables. The second main issue with laboratory scaled rock blasting is the nature of the small form-factor explosives required for use in a scaled setting. These explosives that are utilized, traditionally PETN detonating cord, have a greater ratio of potential energy converted to shock energy rather than gas energy when compared to traditional field explosives, such as emulsion or ANFO. Research over the past decades has indicated that gas pressure has the greatest contribution to rock blasting performance, such as fragmentation and material throw. The factor of varying ratios of energy production has not been discussed in any of the reviewed publications. Publications discuss dimensionless scaling, dynamic similitude, and length-based scaling, however, none of these scaling methods discuss the ratio of energy production. The main focus will be correlation of energy production ratio of shock versus gas to dependent variables. This paper analyzes previous publications within rock blasting and related field as they pertain to scaling procedures and will highlight the similarities and differences in the various publications and detail the observed omitted variables that possibly lead to skewed data.

Jan 21, 2025

By Harley Cheema, Brandon Fryman, John Tatom

A new magazine propagation model has been proposed by the IMESAFR Science Panel for eventual implementation into the IMESAFR QRA program. Initial results from this QRA propagation model are now available.

Feb 1, 2020

By Mark Roberts

Automation, data analytics and optimisation are key trends in the mining industry. Doing more, and better, while expending less resources targets KPIs around efficiency and productivity. With the explosion of data, the next step is to develop an optimal level of processes and systems to harness this data to support value-in use decisions. Typically, significant amounts of resources and effort are invested to develop realistic simulation models. However, models are frequently not integrated with existing systems, and therefore are underutilised. When we consider the specialised process of blasting, integration with upstream and downstream processes is a significant driver to realise sustained improvements and value. The application of genetic algorithms and cloud computing to solving complex mining problems has advanced over the last 15 years, in particular with mine scheduling. Genetic algorithms are unique in that they support true multi-objective optimisation, utilising population-based methods to present trade-offs between multiple solutions. Secure in-cloud processing speeds up the processing, with results delivered in timeframes that are not feasible with desktop computing.

Feb 6, 2023

By Paul L. Matrin

This paper will discuss the recent and on-going drill and blast optimization measures at the Sparkhule Limestone Quarry, which have resulted in a 44% reduction of drill and blast unit costs per ton of broken limestone. This amounts to approximately $240,000 of drill and blast saving per year at current annual production rates of about 2.5 million tons (2.3 million tonnes) total material shot. The reduction of drill and blast costs were accomplished by a detailed and controlled in-the-mine drill/blast experimentation and cost evaluation using 8 different blast pattern designs and shots totaling approximately 267,000 tons (242,200 tonnes) of shot and mucked material. A careful review of the geology of the deposit was performed to determine the different rock classification/strengths/structural properties and to adjust blast designs to optimize fragmentation for the different rock types. Equipment loading productivity and crusher throughput performance were monitored as part of the evaluation process to assure that an optimal fragmentation of broken rock was achieved with the new blast designs. The study included the review of bulk explosive and accessory selection criteria (ammonia nitrate/fuel oil mix - ANFO, mini prills (high density ANFO), sensitized and un-sensitized emulsions at a 30% emulsion/70% ANFO blend), blast pattern design, charge diameter and the cost of drilling. Laser profiling technology was used to assure proper bench heights, stemming and sub-drill footage and front row burdens. High speed photography, video and still photos were taken of the different designed shots to assist in the evaluation of the performance of each blast. Powder density checks, size distribution, back break, detonation velocity and pressure measurements were taken. Different borehole diameters were used for the drill optimization study and drilling cost and productivities determined. A detailed cost comparison between in-house blasting and complete shot service was prepared to evaluate if shot service is a cost effective alternative to current in-house loading and blasting including a review of the new and pending United States Bureau of Alcohol, Tobacco and Fire Arms (ATF) regulations and associated owner costs/risks and potential benefit of shot service.

Jan 1, 2004

By Cory Loukides, Cathy Aimone-Martin

Blaster training manuals used by the Office of Surface Mining (OSM) and others are outdated and cumbersome. A new approach has been developed using Microsoft PowerPoint with a Visual Basic overlay to produce modules on CD’s that present state of the art blasting techniques. The education modules contain enhanced information on topics such as explosives and initiation products, blast design, drilling, and vibration control. The content is based on safe practices and illustrated with numerous photographs and movies. Review questions, complete with explanations for incomplete answers, enhance the learning process and keep the blaster involved. The benefits of using an electronic format include the ability to continually change and update the training modules as new products, technology and applications become available. In addition, the blaster can work at home in preparation for class work and may reduce the time away from the job. This poster session presentation will allow potential users to view and take part in the evaluation of these modules.

Jan 1, 2004

By Lazar Kricak, Zoran Teodorovis, Dragan Bogunovic

Scattering of delay interval around nominal value is an important issue in blasting practice. The scatter interval, as becomes wider, increases a probability of time delay overlapping adjacent blastholes. An excessive flyrock, ground vibrations, air blast and poor fragmentation are the symptoms for scattering related problems. Utilization of the short delays in the blastholes and longer delays on the surface are recommended solution to overcome mentioned problems. In contrast to global trends manifested through the application of electronic detonators and non-electric shock tube systems, revitalization of inexpensive electric detonators in combination with an accurate initiation system may be an acceptable solution. An extensive work was carried out at the Blasting Center Laboratory at the College of Mining and Geology, University of Belgrade, to develop a precise initiation system. As a result, Sequential Blasting Initiation System – Radio Frequency (SBIS-RF) was developed. It is expected that this system will increase blasting productivity, and reduce negative environmental impacts and total blasting costs.

Jan 1, 2008

By S. M. Geerts, M. T. Wild

In this paper the performance effects of various shaped charge liner designs will be discussed. Several different charges will be tested and the liner design will be reviewed based on the performance in testing. The first type of shaped charge to be tested is a conical charge with dual confinement. For the purpose of this paper, dual confinement is a shaped charge with two liners but containing one explosive charge. Several charges with different dual confinement designs will be tested. Variations in configuration include charges with similar angle and similar diameter. The second type is a double conical shaped charge configuration. A double shaped charge will be considered to be two complete charges formed into a single cone. The goal of the project is to determine if any of the designs increase the efficiency and/or effectiveness of the shaped charge in comparison to the standard conical shaped charge. A standard conical charge will be detonated against a witness plate to get a standard depth of penetration or a baseline. All charges will have a seven cone diameter standoff, allowing the data to be compared to the control charge. Computer modeling will be used to predict the results of the testing that will be conducted. The actual results will be compared to the computer simulation for validation.

Jan 1, 2010

By María Virginia Ramírez, Alejandro Alarcón, Alea Reyes

Reactive grounds (presence of FeS2, CuFeS2) can create hazards in a mine; misfires to premature deflagration or detonation of loaded blast holes. This occurs because some minerals can react to ANFObased explosives. Due to a high potential event that occurred in The Mine in 2013, The Mine and the Explosive Provider (“The Company”) are conducting a soil characterization of the areas containing reactive sulfides. This study was planned along with The Mine and it is being developed by a multidisciplinary team.

Jan 1, 2018