Search Documents

By Kai Nielsen

A model has been developed for sensitivity analysis of open pit bench blasting. The model simulates the cost effectiveness of various blasting designs in relation to the equipment used for drilling, loading, hauling and primary crushing. The simulations will give an indication of the optimum powder factor giving the lowest over-all costs for drilling, blasting, handling and crushing.

Jan 1, 1985

By R A. Farnfield

Measurement of the environmental impact of ground vibration from blasting operations is based almost exclusively on the peak vibration level generated. This measurement is known as the Peak Particle Velocity or PPV. The recorded PPV is used to assess the impact of the vibration both in terms of structural damage and human response. Limits for vibration are almost universally quoted in terms of PPV levels and, as a consequence, blast design for vibration control is centred around techniques for the control of this peak value.

Jan 1, 1996

By Marlyn G. King, Robert L. Martin

Blasting activities in all four pits at Thunder Basin Coal's Black Thunder Mine are focused on cast blasting. With widths varying from 190 feet to 265 feet and bench heights varying from 90 feet to 175 feet, casting efficiencies vary with different geometry's. For example, the percent cast to final in the 200 foot pit is on the average higher than the 270 foot pit. The powder factors are somewhat higher in the narrower pits, thus increasing the cost of blasting. This leads to a very detailed look at the actual benefit of cast blasting and the associated cost of these benefits.

Jan 1, 1995

By Winfried Rosenstock

Following successful trials at Chuquicamata / Chile from February to May 2000 and from February 2001 onwards at Burton Coal Mine, RAG International/Thiess Pty Ltd., Queensland / Australia a significant advancement in blasting technology was achieved using electronic detonators. The mine now uses electronic intiation for the majority of overburden blasting.

Jan 1, 2002

By T J. Wilton, K A. Broadhurst

The United Kingdom, although a relatively small island, has a wealth of mineral deposits, coal, granite, limestone, gypsum, lead, florspar, etc. Coal is a major source of energy with 71 opencast coal sites, 52 using explosives. Many of these sites are in rural areas, the average area worked being 250 acres. The smallest is 35 acres, the largest 2,000 acres, but only 600 acres can be operated at any one time.

Jan 1, 1981

By Donald Little, Larry Unger

This paper will give a detailed insight into hard rock, large diameter surface blasting including some practical tips to improve blasting practices. These tips will be non-technical, of the nuts and bolts type, intended to help the man in the boots. The paper will begin with the importance of communication between the engineering department and the blasters. What looks good on the mine development map might not blast very well. Tight inside corners, 90 degree outside corners, too few rows; are a few of these problems.

Jan 1, 2006

By Jacques Monette, P K. O'Connell, Keith Boyle

The mine contracting industry in Canada is no different from any other industry in its quest for productivity improvements. Dynatec Mining Ltd. has focused on drilling and blasting of rounds as an area for improvement. This paper describes the development of blasting long rounds in shaft sinking as well as a description of the lateral excavation system as applied at Aur Resources Inc., Louvicourt Project.

Jan 1, 1994

By Dale Preece, Stephen Chung

Mining and quarrying industries recognize blasting as the most effective method for breaking and removing large volumes of rock. However, the economics of blasting are often offset by the costly trial-and-error approach. Researchers in the field of blasting therefore design models to help eliminate the number of trials before finding the best feasible solution. Because of the complexity of blasting, a capable model would allow the designer to look at more than one variable at a time so that the most critical factor can be tackled.

Jan 1, 2002

By Theodore C. Hile, Floyd P. Henry, Ken Gragg

"Conventional explosive-storage methods usually rely on combinations of earth and concrete barriers, along with sufficient distance between limited explosive loads, to avoid accidental conflagration. However, under many circumstances, Air National Guard (ANG) facilities co-located with civilian airfields have trouble meeting necessary Quantity-Distance (Q-D) requirements for Explosive Hazard Class/Division 1.1 and 1.4 materials. Because of the danger posed by explosives stored in earthcovered magazines (ECMs) too close to civilian activities, ANG units often find itdifftcult to maintain adequate stores of ordnance needed to meet unit mission goals."

Jan 1, 1999

By Josh Campbell

Modern blast engineering involves the use of modern technology to provide more efficient blasts. Through the use of improved measurement techniques more information can be obtained on many of the physical variables of a quarry rock face. By employing this information, a more efficient production shot can be designed and loaded. Along with improvements in production, greater safety and improved environmental impact can be achieved. This paper concerns the employment of modern blast engineering at a granite quarry in the Southeastern United States. The test period extended over a period of approximately six months, and this paper will show the results achieved in that time span.

Jan 1, 1998

By Qingshou Chen, Gongbo Li, Hengqian Ran

A method for safe fracture of rock, concrete and other brittle solid material using dynamic water pressure by explosion is provided. The propagation of the pressure is studied with Allievi water hammer theory. Wave equation and velocity formulas of the pressure propagation are shown. The dynamic water pressure is tested in the lab. The propagation of the pressure is simulated by MMIC-2D. The results of fracturing rock in the lab and on a quarry are presented.

Jan 1, 2000

By Yuji: Wada Ogata, Kunihisa Katsuyama

It is well known that a compressed stress wave reflects at the free face, it propagates to the backward as a tensile stress wave, and cracks grow when the tensile stress becomes the dynamic tensile strength. The behavior of these cracks has been discussed through the observation of the dynamic photoelastic high speed photography.

Jan 1, 1993

By Scott Giltner, Allan Koski

Blasting is one of the lowest cost yet most critical parts of the mining cycle. This paper discusses the findings of an audit conducted on the blasting operation at an iron ore mine. The purpose of the audit was to review current blasting practices in order to identify opportunities for production/cost improvements. The approach taken in the audit was to observe general blasting practices, their related downstream effects and to compare current procedures to established best practices.

Jan 1, 2009

By Paul Worsey, Larry Kenchel, David Randall, Mark Schmidt

The University of Missouri-Rolla (UMR) has historically maintained a manual, paper inventory of explosives stored and used at the university. Although this system was accurate for inventory control and reporting criteria, it was labor intense and delays in record keeping were predominant. A directive from the university’s administration mandated the development of a precise real time system “on-line” to maintain and control the explosives inventory in line with the universities new chemical tracking policies.

Jan 1, 2001

By J Paul Tidman, Stephen H. Chung

One of the requirements in open pit gold mines is to minimise the mixing of ore and waste. Dilution can be reduced by choke blasting and control of the initiating sequencing. The authors have used the DMC computer model (developed at SANDIA) to examine the effects of timing and charge distribution on ore dilution. The model has been calibrated by measurements of vertical uplift derived from high speed videos made at the Dome Super Pit in Timmins.

Jan 1, 1997

By Joseph A. Sohara, John J. Mullay, Curtis J. Keefer, Robert L. Schrepple

The desensitization of an explosive column by the action of a previous detonation (adjacent borehole, deck or detonating cord) is a vital concern to the explosives industry. Previous reports to this symposium and in other places have addressed this issue. However, this work has been mainly concerned with model or simulated conditions. No systematic study has appeared that utilizes an actual borehole environment. Thus the relation between this work and expected field performance is somewhat uncertain. The present paper attempts to partially resolve this difficulty.

Jan 1, 1990

By Michael E. Kovach

This discussion is an overview of an approach to drilling and blasting angle holes at Martin Marietta Aggregates. Method of determining burdens, hole depths, angle settings and explosive selection will be discussed in detail with an emphasis on safety and production. Such techniques and methods involve the use of hand-held surveying instruments such as the Abney level, pocket transit and inclinometer along with measuring tape and burden pole. An interesting method developed by Oscar Banfield a retired Martin Marietta and E. I. duPont engineer, for setting the proper angle on a drill will also be presented. This treatise is a discussion of the use of simple yet important tools and techniques a blaster should use to resolve both routine and complex problems encountered during quarry blasting operations.

Jan 1, 1992

By O E. Crenwelge

Seismograph measurements are usually made near blasting operations solely for the purpose of monitoring compliance with governmental regulations. However, recordings of seismograph signals have far greater potential than this, if the proper procedures are used for analyzing the transient data.

Jan 1, 1991

Increasingly specialized blasting needs require that the explosive energy available in a borehole be reliably known for representative blasting conditions. The underwater test, when properly performed, can yield such information and thus provide a reliable rating of explosives in terms of energy release. This paper reiterates the stringent experimental conditions to be satisfied, and data analysis and interpretation techniques to be followed to achieve this. This is supported by detailed experimental studies involving select parameters in both detonator and booster sensitive explosive compositions. The paper also illustrates the inadvisability of equating blasting performance with the commonly calculated energy values.

Jan 1, 2000

By Leslie Taylor, W. Fourney, Uli Leiste

This paper presents the results from a series of tests conducted to investigate the total vertical impulse delivered to a target plate by a buried explosive charge. The tests were conducted at a very small scale but previous work has shown that small scale testing can predict impulse applied to plates in full scale. Non-deforming plates were used to determine the change in impulse delivered to targets as a result of changes in standoff distance and burial depth changes.

Jan 1, 2009