Search Documents

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Lina Lopez, Jose Sanchidrian, Manuel Lopez, Pablo Segarra

Previous work in which rock properties and blasting parameters (geometry, charging and timing) were reported together with truck filling times, is taken as a starting point for a thorough analysis of the influence of the former on the mucking velocity. The experimental set was composed by 11 blasts made in an open pit mine. Non-parametric, distribution-free statistics is applied. The mucking rates (in bank cubic meters per unit of bucket volume and per hour) appear to be clearly dependent on the explosive energy and powder factor, both magnitudes combined as energetic powder factor (energy per unit of rock volume). The mucking rate is a non-monotonic function of such factor in the range of the blasts analyzed. The determination of the function is optimum when the fraction of the explosive below grade is not considered and when the explosive energy is qualified as that delivered at a partial detonation regime. Different types of loaders seem appropriate for different energy levels. At low levels both front loaders and rope shovels obtain small productivities without a statistically significant difference in their performance. At high energy levels, front loaders qualify higher than rope shovels. Mucking velocities can be equally small at low energy powder factors and at high ones if rope shovels are involved.

Jan 1, 2008

By M. L. Mendes, J. Q. Nojiri, S. C. Botelho, A. P. Campanha

In February 28, 2001 JOULE coordinated the first tests with an electronic detonator in South America at an iron ore operation - ITABIRA MINES from the Brazilian COMPANHIA VALE DO RIO DOCE (CVRD) - the largest producer and exporter of iron ore in the world. ITABIRA MINES (CAU and CONCEI O) belong to one of the complexes, called the Southern System, producing 56 million tons of ROM as well as concentrated products and pellets. This paper is going to describe the tests at ITABIRA MINES with results indicating the improvement in the excavator productivity and reduction of the mining global costs (due to the better performance of the equipment and potential reduction of the maintenance cost).

Jan 1, 2002

By Changa-Ha Ryu, Hae-Moon Choi, Sang-Don Lee

The rock mass to be excavated is classified using data obtained from the initial site investigation, and the design of excavation and support is then made based on the rock class. Rock classification provides an empirical design with guidelines for tunnel support compatible with rock mass quality and the method of excavation. Although most clients provide standard patterns corresponding to each rock class, the patterns of drilling and blasting have only been used in estimating the excavation cost and not used in the construction stage. The purpose of the study presented in this paper is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing the country. Long hole blasting was tested in rock mass whose RMR value is over 60. The blasting results were evaluated by measuring degree of fragmentation, advance rate, muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a twolane highway tunnel.

Jan 1, 2005

By Dal Sun Kim, Michael K. McCarter

"Comminution (crushing and grinding) of rock materials is energy-intensive and expensive. Mucheffort has been directed to improve the efficiency of conventional milling practice, but relatively littleattention has been given to the potential benefits of blast-induced damage on comminution processes. To help assess this effect, research has been conducted at the IRECO Laboratory and the Generic Center for Comminution at the University of Utah. The objective of this research is to investigate the effect of shockinduced “crack-like” damage on rock properties and subsequent breakage efficiency for three petrologically different rock materials under laboratory conditions. In order to evaluate the effect of shockinduced damage, a quantitative measure of rock damage is needed. For this purpose, a scalar variable (0) is proposed."

Jan 1, 1993

By Dale Preece, Stephen Chung, D. Scott Scovira

The DMC_BLAST (Distinct Motion Code) has been developed to model rock motion and displacement during the gas expansion phase after the detonation of an explosive in a borehole. Recently, a designated delay firing order algorithm was written into the DMC_BLAST code. The model can now be used to analyze rock mass displacement for a V-cut, center opening, or sinking cut initiation sequences. This new feature allows the investigation of the effects of delay firing order on rock displacement when blasting complex inter-bedded and ore-waste structures. The model provides important ground movement and mixing indicators for dilution control in surface gold mining relative to the initiation sequences employed. Echelon blasts as compared to center opening type blasts show differences in their internal muckpile displacement. These displacement differences can be important to operations that mine narrow strike driven ore bodies. The model also has applications to through coal seam blasting and demonstrates that down-dip blasting is a better alternative than up-dip blasting. There is less disturbance to the dipping coal seam and less mixing of the rock and the coal.

Jan 1, 2000

By Brian Stump, D. Craig Pearson

This work quantifies seismic coupling as a function of charge weight for single-fired (simultaneously detonated) explosions observed in the mine and at regional distances. These single-fired explosions are contrasted to standard production shots from the same mine. Production shots include cast blasts to remove overburden and coal shots for fragmentation. The blasts were conducted in a mine in NE Wyoming. The data sets consist of measurements in the mine (100-10,000 m) and at regional distance (360 km) using a seismic array near Pinedale, Wyoming (PDAR). The single-fired explosions ranged in designed size from 5,500 to 50,000 lbs. Peak amplitudes measured at a single element of the regional array are modeled by a power law relation dependent on explosive weight. Scaling constants were determined for each of the dominant regional phases: b(Pn) = 0.84±0.14; b(Pg) = 0.84±0.09; b(Lg) = 0.91±.08. Spectral ratios of observations from different explosions observed at the same station illustrate the frequency dependnce of the source scaling relations. Spectral ratios of in-mine observations are consistent with those of regional data. The observed single-fired ratios are well replicated by Mueller-Murphy source model ratios. The data and model illustrate both the increase in long-period spectral level and the accompanying decrease in source corner frequency with increasing charge weight. The coal and cast blasts that make up the production shots ranged in size from 77,000 to 4,738,230 lbs. The peak amplitude (1-20 Hz) for the largest delay-fired production shot (4,738,230 lbs.) is comparable to that of the largest single-fired explosion (50,000 lbs.). This comparison can be explained in terms of destructive interference between waveforms from individual boreholes introduced by delay firing. Shot specific models of delay firing suggest that peak amplitudes in this same frequency band for the production shots are insensitive to the total amount of explosives in the blast. Peak amplitude data at regional distances supports his modeling result.

Jan 1, 2002

By Larry Schneider

In 1998, the Blast Vibration and Seismograph Section of the International Society of Explosives Engineers formed a working group to collect and compile a list of regulations limiting ground vibrations from blasting. The goal was to locate those countries, states, provinces, and cities that have such regulations, identify which governmental body enforces them, and determine what limits on ground vibrations are imposed upon the blasting operations. In the course of this study, data was collected from over 60 jurisdictions where peak particle velocity restrictions range from non-existent to very stringent. Some of the regulations were found to be based upon standards grounded in good science, while others possess little or no technical justification. This presentation will summarize the findings of the subcommittee, focusing primarily on what the limits are, which type of blasting operations must adhere to them, and to what structures they apply. The degree to which these regulations are based upon valid scientific and engineering research will be discussed. A listing of specific locations having such regulations and information about those regulations will be provide

Jan 1, 2000

By Tom Donnelly, Roger C. Ilsley

Remote telecommunications seismographs were used to monitor blast vibrations at two historic structures in Cedarburg, Wisconsin during adjacent sewer line construction. The purpose of the vibration monitoring program at the historic structures was to maintain blast vibrations below limiting tolerances established by the Wisconsin State Historic Society.

Jan 1, 1991

By Kirstin Girdner, Vicki Seppala, Tom BoBo, John Kemeny, Mike Higgins

Optimal blast fragmentation is fundamental to all phases of comminution. Changes in blast design may affect efficiency and productivity of downstream processes such as crushing, milling and leaching, resulting in cost savings or losses.

Jan 1, 1999

By Lewis L. Oriard

This paper describes the process of developing blasting specifications for 850 miles of new pipe trench running parallel to an existing high-pressure gas pipeline, often with as little as 14 ft to the existing pipeline trench. The primary method of preventing damage to the existing pipeline was the use of fracture (overbreak) control.

Jan 1, 1994

By K Uenishi, H P. Rossmanith, N Kouzniak, A Daehnke

This contribution presents an introduction into that part of the field of elastic wave propagation which is relevant to blasting of boreholes and addresses briefly borehole breakdown and the formation of the fracture network around a borehole which ultimately leads to the disintegration of the rock mass. Phenomena of this kind are encountered in mining and quarrying. Numerical as well as experimental work referring to stress wave expansion from a detonating borehole is addressed.

Jan 1, 1998

By Keith L. Bockelman

The Colowyo mine is a unique surface coal mining operation because it is a multiple seam pit. Using a combination of a shovel-truck and dragline operation, Colowyo mines 8 seams of coal to a depth of 400 ft. Over the past 3 years a number of operational changes have occurred, one of which is the implementation of blast casting. Through this implementation Colowyo has been able to eliminate over one million cubic yards a year, which would have had to be removed by the shovel-truck operation. This has also brought about a significant decrease in the stripping cost per ton within the dragline operation.

Jan 1, 1985

By Stephen H. Chung

Direct visualization of rock movement during blasting is an important key to understanding the blasting process, as well as optimizing blast designs and explosives performance. To achieve this, a digital camera system (HSIS-500) has been built. It is a custom made high speed solid-state camera employing an advanced charge coupled device (CCD) and dynamic random access memory (DRAM) technologies. It handles like a regular video camera but requires no film or tape as the image is recorded in digital form on memory chips and transferred to the system hard disk for storage. The system consists of two components: the camera body and hardware, and the image processing unit.

Jan 1, 1996

By Brian W. Stump

The cessation of testing of any nuclear explosive devices in all environments is the goal of the Comprehensive Test Ban Treaty. In order to assure compliance with such a treaty, an international monitoring system has been proposed. This system will include seismic, infrasound, hydroacoustic and radionucleide monitors located throughout the world. The goal of this system is the detection of any nuclear test. In preparation for this treaty, a series of monitoring system tests, focusing primarily on seismic observations, have been undertaken. The most recent of these tests, Group of Scientific Experts Technical Test Three (GSETT-3), provides valuable data for assessing future monitoring systems. During the course of this experiment, seismic events associated with earthquakes, nuclear explosions and mining explosions have been recorded. This presentation will discuss the numbers and types of mining explosions triggering the system, in a particular area. Possible implications for the mining industry will be explored.

Jan 1, 1997

By Dwayne Tannant, Jeffrey Loeb

Blasting techniques and protective measures exist that can mitigate risks associated with flyrock and the nuisance of vibration, and overpressure. However, these are often misused or not used because there are no prescriptive regulatory requirements and typically urban blasting guidelines do not exist. The relationship between the increasingly negative publicity that the urban blasting industry receives and the existing state of regulatory control on blasting in urban environments is presented.

Jan 1, 2012

By J S. Kuszmaul

"A computational model of rock blasting is being developed to examine the blasting problems associated with in situ oil shale processing. This model, however, will also be useful as a design tool for the traditional problems in rock blasting. The model includes fundamental treatment of both shock-wave propagation and the accumulation of brittle fracture in the rock. As a result, the model accurately predicts the degree and extent of fracturing as functions of design parameters. The model has proven useful for making parametric studies and for evaluation of alternate blast designs. This paper demonstrates the use of the numerical model to simulate the fracturing induced by the detonation of a vertical explosive column near a bench. The fracturing induced by three differentexplosives indicate that (in the chosen geometry) the most efficient breakage is done by a column of ammonium nitrate and fuel oil mixture (ANFO) used with a toe charge of aluminized ANFO. There was too much unfractured rock left when ANFO was used alone; aluminized ANFO used for the entire explosive column caused excessive fracturing. A final case involves ANFO used alone to fracture a different rock type. This case points out that in a different rock type, the ANFO will not leave excessive unfractured rock."

Jan 1, 1987

By D. C. Valdemeri, Oppermann J. P. Z., R. G. Schaarschmidt, C. S. Mendonca

This case study was conducted in an aggregate company, located at Estância Velha town, RS, Brazil. The study was based on the results of vibration monitoring mainly in terms of PPV (peak particle velocity) and frequency. Changes in the blasting design were performed to adjust the limits determined by the Brazilian standard NBR 9653:2005. Understanding the seismic wave attenuation for the site, changes in the blasting design were tested to fit the limits, such as reduction of maximum charge per delay, initiation orientation and sequencing and finally the replacement of accessories like "shock tube" by electronic initiation system. The results are shown below.

Jan 1, 2015

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By Frank Lucca

This study is based on a six month study performed for Lee County, Florida. The study was based on blasting for land development and how this type of blasting affects structures. The study is investigates peak particle velocities and the relationship to other environmental and manmade forces that affect structures. The study also explores the effect of geology on blast vibration. After completion in Lee County, the study was then continued in the quarry environment in Vermont and extremely tight blasting environment of New York City. Charge diameters were 127mm (5 inches) or less.

Jan 1, 2006