Search Documents

By A. N. Zagorodnyaya

The results of research on recovery of ammonium perrhenate from by-products of lead production are presented in the article. For the first time in the world, rhenium marketable products were produced on lead plant of Kazakhstan. Distribution of rhenium in lead production has been studied. During oxidative agglomeration of lead charge, 67.43% rhenium is sublimated and at that, 67.27% rhenium is trapped by the dusts of a system of gas purification, out of them 6.21% is transferred into different solutions, 1.89% into slime and only 0.09% into exhaust. During agglomerate smelting, up to 72% of its rhenium is sublimated and condensed in the dusts also. At leaching stage of sulphate product under dusts processing by the method of sulphatization, 15% of its content in the dusts is transferred into solution. The sorption method on the ionite ?N-21 has been proposed for recovery of rhenium from the solutions of sulphatization. At the same time, rhenium recovery from the dusts into commodity was 13%. The method of direct hydrometallurgy - leaching the dusts by solutions of sulphuric acid under presence of manganous concentrates, has been proposed as alternative method of recovery. This method has allowed increasing recovery of rhenium and other metals from the dusts into solution up to 90%~95%. Rhenium solvent extraction by ??? has been proposed for recovery of rhenium from the leaching solutions. At that, extraction of rhenium into marketable product from the dusts is above 75%.

Jan 1, 2014

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014

By N. P. Haran

A detailed study was undertaken to beneficiate sub-grade iron ore sample from Kenojhar District, Orissa, India containing 57% Fe (T), 7.7% SiO2, 4.8% Al2O3, 4 % L.O.I. 0.4% TiO2,1.3 % Mn and traces of S(T) to make it suitable for the user industry. The mineralogical study indicated that it predominantly consists of haematite with subordinate amounts of goethite and clay. Quartz, Cryptomelane / Psilomelane, Pyrolusite, Gibbsite, Feldspar and Muscovite mica were present in very minor to trace amounts. The Denver grind ability tests indicated, that the sample could be categorized as ?medium soft to medium.? The Bond ball mill work index was determined to be 14.19 kwh per short ton. The beneficiation process involved classification followed by tabling of the classified sand, ground to minus 48 mesh size. The table slimes were subjected to Wet High Intensity Magnetic Separator (WHIMS). The developed process yielded a composite concentrate from tabling and WHIMS operations assaying 65% Fe(T), 2% SiO2, 1.8% Al2O3, 2% Mn and 0.9% LOI with a recovery of 60.1% Fe (T), amounting to 52.5 wt.% yield. To meet the size specifications for pellet making, it was further ground. Dewatering studies were also carried out on the ground combined concentrate and rejects. The thickener area of ground combined concentrate using 0.02 kg/t of Sufloc A 1115 flocculant was 0.02 m2/tonne of dry solids per 24 h. And for the combined rejects using 0.12 kg/t of flocculant, it was 0.035 m2/tonne of dry solids per 24 h. The moisture content, in the pressure filtration cake, in the ground combined concentrate product was 10.0%, and productivity was 506.7 kg/m2h. Thus, by thickening and filtration of process products, 90% of water used in the process could be recovered. The study highlights the development of a simple and cost effective flowsheet with almost complete water recovery for a subgrade iron ore sample. Keywords: tabling, WHIMS, thickener, filtration

Sep 1, 2012

By W. Z. Yin

With increasing of mining depth, many iron ores in Liaoning Province contain carbonates such as siderite and ankerite. The emergence of these carbonates in ores creates a fatal impact on the running producing process of anionic reverse flotation in Dong Anshan Sintering Plant, which leads to ?concentrate and tailing no separated?. And its reason is still unknown. Moreover, siderite, despite that its ferric theoretic grade is only 48.2%, however, do not affect the blast furnace utilization factor, therefore, can be used as raw materials in ironmaking. In order to solve the separate problem of iron ore containing carbonates, five pure minerals, martite, magnetite, quartz, siderite and ankerite, were selected for a series single flotation experiment. The aim was to discover the flotation difference of these minerals, furthermore, to explore a new flow sheet for the iron ore containing carbonates. The results of single mineral flotation experiment reveal that the combination regulators, starch and CaCl2, in different pH extent, can make these minerals taking on obvious flotation difference, which make it possible to process the iron ore containing carbonates. A new flow sheet, step-flotation, to process iron ore containing carbonates is explored, that is, first step, direct-flotation processing, is to eliminate the bad effect that the carbonates bring in flotation system by collecting carbonates under neutral condition; the second step, reverse?flotation processing, is to get qualified iron concentrate by collecting quartz under alkaline condition. Manual mixed ore sample were processed successfully through this new flowsheet under proper reagent system, which has absolute advantage compared with routine flowsheet. Actual ore sample of compound magnetic separation concentrate were processed successfully both open and closed circuit experiment through this new flowsheet. SEM and EDS were used to probe the reason why carbonates affect the regular processing. It is analyzed that moderate floatability of siderite and its coating on the surface of hematite and quartz make the phenomenon ?concentrate and tailing no separated?. This research provides a reasonable processing scheme for iron ores containing carbonates and can be used for reference in processing other complicated, refractory iron ore.

Jan 1, 2014

By J. Quinteros-Riquelme

Despite increasing demand, the supply of silver is limited by its inadequate recovery from ores. Due to its scarcity in nature, its high ore variability and complex mineralogy of current silver deposits, its recovery by mineral froth flotation presents a real challenge for process engineers. A silver ore often contains significant amounts of five to ten different silver minerals and knowledge of the mineralogy is a necessary precursor to flotation testing. In this work, a complex silver ore was treated by using batch laboratory flotation, in an effort to find the best experimental conditions to obtain the optimal silver recovery. Mineralogical characterization of feed samples was conducted using a combination of tools, namely the mineral liberation analyzer (MLA) and inductively-coupled plasma mass spectrometry (LA-ICP-MS), which indicated that most of the silver occurred as ?invisible? silver in pyrite. The pyrite assay of the ore was approximately 4%. The ore was processed in two flotation stages. The first stage, sulphide flotation, aimed to collect a sulphide mineral rich concentrate; then a non-sulphide flotation stage was performed by adding sodium sulphide and collectors to the remaining material in the cell, with the objective of obtaining a pyrite rich concentrate. To reach the target recovery of silver from this ore, various variables were altered. In the first stage: mixed collectors, activators, dispersants, and mainstream inert grinding were assessed. In the second stage, the conditions for sulphidization and subsequent flotation were both investigated. From the grade recovery curves for silver and sulphur it was possible to observe a similar metallurgical behavior for both elements, supporting the results given by the mineralogical characterization. Keywords: silver oxide, froth flotation, sulphidization, mig

Sep 1, 2012

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

By Shi Shuaixing Zhang Yuejun, Fan Xuesai Zhangming

"For the traditional principle of flotation cell design, or in the perspective of some researchers, the mixing effect of impeller for flotation cell is not only to suspend the particles off the bottom, but also to mix slurry well to achieve a uniform system. But for some special processing conditions, the depth profile of slurry concentration and particle size demonstrates an obvious difference. In the part around of the impeller in the cell, the slurry concentration is much higher than the part below the lip.For the vanadium titano-magnetite flotation process, distinguished with high concentration and large coarse particle size fraction, even though the concentration is very high, it can reach good gas dispersion, which is a fundamental principle for flotation cell design and application. The gas dispersion is not a challenge in the high slurry concentration environment, not only in the vertical direction, but in the cross section. Different levels (the distance from the lip is 400mm, 700mm, 1200mm, 1700mm, 2200mm, 2700mm) slurry in the flotation cell is sampled and analyzed. The slurry concentration of the 3 levels(1700mm, 2200mm, 2700mm) is about 55%, but the slurry concentration decreases from 55% to 25% sharply towards the lip.Therefore, a new understanding and viewpoint is presented, that the uniform system of slurry is not always reasonable for all of the flotation process. For some special process, if the coarse particles are needed to agitated well and transported to the upper cell, the quiescent zone in the upper cell will be destroyed and enhance the detachment probability for the coarse particles. The difference of slurry concentration and particle size fraction benefits the air dispersion and coarse mineral particles recovery.1.INTRODUCTIONNowadays, flotation is the most widely used separation process in the mineral processing industry. The importance of flotation technology in the global economy is significant. A rough estimate of the quantity of crushed ore treated by flotation is about nine billion tons per year, and the portion of base metals processed using this method is approximately 95% (Brewis, 1996)."

Jan 1, 2018

By B. Csoke

As opposed to large household appliances, in the processing of which dissambling has an important role, this possibility is pushed into the background as the size decreases. The practicable solution is physical liberation of the used small electronic household devices (by comminution) and separation of the liberated components according to their physical properties. In the first phase of the experimental work the structural/material composition of the typical products (mixer, kitchen robot, hair dryer, coffee machine, iron, bread toaster, vacuum cleaner, oil fryer) was determined. In the second phase a physical liberability test for each appliance using a rotary shear/shredder for crushing and a hammer shredder for milling was carried out. In the third phase the experimental separability tests using an air classifier and a shaking air table, as well as an eddy-current and an electrostatic separator were performed. In the present paper the results obtained using the air classifier and the electrostatic separator, are reported. To follow the life of a grain a new methodological procedure was elaborated. The particle size fractions after comminution were sorted into material fractions (copper, aluminium, plastics, etc.), then separated, and finally the recovery of the material components in the products were determined. Furthermore, the joint separability was investigated from two points of view: 1) for grain fractions and 2) for each waste appliance. According to the tests carried out so far, it was established that it is reasonable to form appliance groups by selection (e.g. mixer, iron, bread toaster and similar appliances form the first group, while the sandwich oven,

Jan 1, 2014

By J. Y. P. Leite

In the Borborema Pegmatitic Province (Brazil) exploitations of several minerals are conducted by small producers. They use traditional techniques of gravity concentration in small-scale plants as jigs and vibratory tables. During decades the mining activity generated tailings with economic interest in particularly columbite-tantalite. Samples collected in tailing piles of a gravity plant were characterized in mineral composition, which shows in the heavy fraction the minerals spodumene, columbite-tantalite, ilmeno-hematite, garnet and cassiterite. The light fraction presents quartz, feldspar and muscovite. The degree of liberation of spodumene and columbite-tantalite were determined using optical microscopy that presents liberation in 100 µm (90% to columbite-tantalite and 100% to spodumene). Centrifugal concentrator Falcon SB-40 was used for concentration of these minerals and presents 65% recovery in mass to two stages with mass reduction about 85%.

Sep 1, 2012

By D. W. Lui

Tangdan copper oxide deposit, the largest independent copper oxide deposit in China so far, is located in the northeast of Yunnan province, southwest of China. The ore from this deposit is characterized by: low grade, high oxidation ratio, and fine-grained disseminated, resulting in poor flotation recovery. The analysis of plant flotation data reveals that the loss of copper minerals into tailings is mainly with coarse size fraction due to insufficient liberation and fine size fractions, especially minus 10 microns fraction, which proved to be very difficult-to-float with conventional flotation. In order to improve the performances of plant flotation of this ore, laboratory flotation tests were conducted with the pure malachite, which was the principle copper oxide mineral in Tangdan copper ore deposit. The results obtained suggested that a finer grinding (up to -325 mesh or even -400 mesh) be needed to decrease the loss with coarse size fraction, and vacuum flotation is a promising way for the recovery of the fine malachite effectively.

Jan 1, 2014

By A. A. Sirkeci

In the scope of this investigation comparison between impact breakage and compression breakage were carried out for the separation efficiency of minerals using a chromite ore sample. The ore sample was broken below 1 mm employing a laboratory type roll crusher and an impact crusher. Concentration tests were conducted on -1+0.5 mm, -0.5+0.2 mm and -0.2 mm size fractions using a Wilfley type shaking table. Test results showed a remarkable difference between two types of breakage. Both concentrate grade and recovery was in the favour of impact crushing. Furthermore, the shape of the broken particles also showed differences such that in the case of impact breakage they were more spherical compared to compressive crushing. The results of the shaking table con-centration tests showed that a concentrate assaying 48.4% Cr2O3 were obtained with 78.5% recovery in the case of impact breakage. On the other hand the concentrate grade and recovery values were 48.8% Cr2O3and 52.4% respectively in the case of compression crushing. The losses in the tailings were also in favour of impact breakage proving that differential breakage occurred between chromite and gangue minerals.

Jan 1, 2014

By S. L. Gao

Based on the differences in hardness and density of diaspore and aluminosilicate minerals which usually exist in Chinese diasporic bauxite, It is analysed that bauxite of this kind is difficult to be separated effectively by classification and normal gravity separation, and cyclonic centrifugal field was thus proposed to be carried out, in which classification can take place according to the size difference resulted from selective grinding, what?s more, the separation function according to density difference is expected to take effect at the same time, and then cyclonic separation tests for diasporic bauxite of A/S 4.39 and grinding 61.90% -0.074mm were carried out tentatively. The results showed that the accretion of feed pressure can offer strong enough centrifugal force for cyclonic separation with result that separation function according to density difference is effectively intensified, by the increasing of this parameter, underflow and overflow of A/S 7.64 and 2.18 can be processed at the same time, and the recovery of Al2O3 in underflow is 71.78%; judging by the flow ratio, the spatial locality envelope of zero vertical velocity do constringe to the vertical axis by the enlarging of diameter ratio of apex to vortex, overflow and underflow of A/S 2.08 and 6.5~7.0 can be processed by controlling this structural parameter, which is possible to offer a technological method for low-grade bauxite to de-sliming beforehand.

Jan 1, 2014

By M. Illikainen

Limestone is used for neutralization of acid leachates in a number of hydrometallurgical processes. The aim of this study was to clarify how limestone ground to different particle sizes can neutralize sulfuric acid. The laboratory scale ball mill was used in grinding experiments carried out using ball sizes of 20, 30 and 40 mm and volumetric slurry densities of 30, 40 and 50 percents. Varied grinding times were used in order to produce limestone samples with different particle size classes on which the neutralization potential and rate were determined. The results of the study showed that the neutralization potential of limestone is not dependent on its particle size between 5 and 120 µm. However, the particle size strongly affected the neutralization rate of sulfuric acid: The smaller the particle size, the higher the rate of neutralization. Thus, when optimizing the cost efficiency of the process, the optimal degree of grinding should be considered taking in account the required residence time in neutralization phase.

Sep 1, 2012

By W. G. Liu

Phenyl malonic acid (PMA), a new chelating collector, which contains a phenyl structure and a malonic acid chelating group, has been synthesized and its collecting capabilities to calamine, hematite, quartz and hemimorphite are also studied in laboratory. From the experimental results, it can be seen that the PMA has somewhat flotation ability to calamine, hematite and quartz, while it nearly has no collecting ability to hemimorphite. With the increase of PMA concentration, the flotation recovery of calamine increases. When the dosage of PMA was 560g/t and at pH=7~9, the flotation recovery of calamine gets its maximum of 45.94%. The test results about the influence of pH on the flotation recovery of quartz show that the flotation recovery increases with the increase of pH, and the maximal flotation recovery can be gained in alkaline media. On the other hand, PMA has stronger flotation capability to hematite than to other minerals. The flotation recovery of minerals increases with increase of PMA concentration. When the dosage of PMA is 560g/t and at pH=5~7, the flotation recovery of hematite is 82.96%. Mean-while, the influence of pH on the flotation recovery of hematite was studied and test results showed that, as pH increases, the flotation recovery sharply rises until pH=4, then the increasing rate de-creases outstandingly, at pH=6 the flotation recovery reaches its maximum of 82.96% and it de-creases speedily in alkaline media. Finally, through the measurement of infrared spectroscopy and in terms of solution chemistry of collector, the flotation mechanism has been discussed. It was concluded that the adsorption of PMA on minerals surface is chemical adsorption in nature through two oxygen atoms in the polar group of phenyl malonic acid chelating with the metal ions of minerals surface to form a hexagon-cycle chelate complex: C(=O)-O-M-O-(O=)C.

Jan 1, 2014

By Sepideh Javanshir

The process of liquid?liquid extraction of gold from chloride solution is complicated by the presence of many variables acting simultaneously in an unknown non-linear fashion for the determination of the final extraction efficiency. In practice, it is quite difficult to develop a model for predicting various properties of such process. Therefore, an alternative approach based on Artificial Neural Network (ANN) is considered to assist in the simulation process. Artificial neural networks (ANN) are powerful tools that can be used to model and investigate various highly complex and non-linear phenomena. This paper presents application of Multi-Layer Perceptions (MLP) to construct relationship that will be employed to develop a quantitative method for the estimation of the extraction efficiency as a function of hydrodynamical parameters such as stirrer speed, [AuCl4]- and DBC concentration, organic and aqueous flow rate. The model is shown to be in excellent agreement with the experimental data (R2 value for training and testing data was 0.9992 and 0.9915 respectively). Therefore, it can be used to optimize the parameters of liquid?liquid gold extraction with dibutyl carbitol (DBC).

Sep 1, 2012

By Zhangm Zeqiang, Manman Lu, Hanquan Zhang, Hong Yu, Jintao Fu

"Pelletizing is an important technique in the ironmaking industry. Artificial and natural magnetites are materials that are widely utilized in the iron ore pelletizing process. In this work, the pelletizing characteristics of these two types of magnetite have been investigated in detail. The obtained results shown that in contrast to natural magnetite, the artificial magnetite concentrate exhibits stronger hydrophilicity, lower electronegativity, larger specific surface area, and rougher surface. In addition, the green pellets produced from the artificial magnetite concentrate are characterized by a higher compressive strength as compared to that of the pellets obtained from the natural magnetite concentrate. However, the shock temperature of the artificial magnetite pellets around 255 C is significantly lower than the threshold specified by the industry. The balling characteristics of the material obtained by mixing 20% of the artificial magnetite concentrate with 80% of the natural magnetite concentrate are considerably improved with respect to those of the individual components.INTRODUCTION Pelletization is an essential process of the ironmaking industry in China. Since the pellets produced from iron ore exhibit high mechanical strength, good particle granularity, and uniform shapes, pelletizing high-grade iron ores with good metallurgical reducibility can lower the coke ratio, improve their technico-economic index, and reduce the cost of processing pig iron in blast furnaces[1, 2]. Presently, high-grade magnetite is a material utilized for pelletizing various iron ores across the globe. However, its natural deposits have been depleting rapidly in recent years; as a result[3], China’s dependence on the foreign high-grade iron ores exceeded 70% in 2009 and reached the level of 87% in 2016. Hence, possible methods for the efficient cultivation of limonite, siderite, hematite, and other refractory minerals that correspond to low-grade, finely sized, inhomogeneous, and scattered iron ores have attracted significant attention [4, 5]. In particular, magnetization reduction roasting and magnetic separation techniques, which are widely utilized for obtaining high-grade artificial magnetite, represent effective ways of processing iron ores that can alleviate the scarcity of natural magnetite resources [6, 7]. The artificial magnetite produced by magnetization reduction roasting exhibits different characteristics as compared with those of natural magnetite (including the degree of hydrophilicity, surface potential, specific surface area, and other surface physicochemical properties[8-11], which significantly affect its pelletizing behavior. In this work, the surface characteristics of artificial and natural magnetites are investigated in detail, and their effect on their pelletizing properties (such as green ball strength, heat stability, and pelletization rate) are examined."

Jan 1, 2018

By P. Banerjee, P. Dash, S. Sriramoju, A. Suresh, R. Lingam, T. Ray

"One single property that influences the quality and market value of coal to the maximum extent is the ash content. The lower the coal ash higher is the energy utilization and potential for different applications. Even though Indian coal washeries aspire to produce coal with low ash, the intimate distribution pattern of ash bearing minerals in the coal matrix becomes the real bottleneck, as it brings down the clean coal yield to the impractical value. Because of this fact, most of the Indian washeries are operated to produce coal with 14-15% ash content at the yield of around 40%. In this context, with an objective to produce low ash coal at higher yield, a novel chemical beneficiation route has been explored to demineralize the high ash containing Indian coals. In this present work, the production of low ash clean coal from high ash Indian coals using chemical leaching process has been studied at pilot plant level. The leaching process parameters such as reaction temperature, reagent concentration, reaction time, coal-liquid ratio and agitator speed have been optimized for the flotation tailings sample from a captive washery of Tata Steel. The results obtained show that 67% demineralization could be achieved in a single stage of leaching process with a product yield of more than 65%. For further demineralization, multistage leaching was carried out and the results showed that 75-85% demineralization could be achieved with significant reduction in alumina to silica ratio. Additionally, the phosphorus content is also significantly reduced from 0.20 % to 0.022 %. Further, it is interesting to note that there is no increment of sodium content in the product coal after chemical treatment."

Jan 1, 2014

By S. N. Shahcheraghi

Bioleaching method makes use of bacteria in solving metallic sulphides, so that these bacteria tend to convert insoluble metal sulphides into soluble sulphates. Since the kinetics description of this process is inevitable for better interpretation of relation between metabolism and growth of live organisms, as well as optimization of metals extraction processes, in this paper, this description is represented and designed in mathematic (kinetics) model for copper sulphide minerals based on Monod kinetics model. According to this model, special growth rate of bacteria (?) is a hyperbola function of restrictive substrate concentration (S). By Solving and developing of Monod kinetics model, a comprehensive kinetics model for bioleaching of copper sulphide minerals results. The designed is also applicable for other metal sulphides.

Sep 1, 2012

By Shuoshi Lu

The Cu-Co ore studied here belongs to the oxide type. The oxidation rates of copper and cobalt are69.30% and 78.78%, respectively. The content of Cu in ROM is 1.34% and that of Co is 0.096%. The ore contains 4.64% carbon.Based on the process mineralogy and previous metallurgy tests, the principalprocess flow-sheet of ?grinding fines 80% -0.074mm, sulphide flotation followed by oxide flotation, and flash flotation for oxides? has been determined.The handling of carbon is determined through tests. The depressant PNL-1 depressed carbon effectively, improved the recovery of sulphide minerals and reduced the reagents consumption.The operation of the flow-sheet was also changed to better at the same time. Keywords: Cu-Co oxide ore, process mineralogy, carbon depression, efficient depressant of carbon

Sep 1, 2012

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018